Technicolor - Thomson ITC008 User's Manual
Contents
1. About this manual This manual is common to several TV models Therefore the model you bought may not support some of the functions or settings described hereinafter About the On Off switch The position of the ON OFF switch differs depending on the model It may be located on the front or on the right hand side of your set see the drawing inside the cover page of your manual For your safety To ensure your own safety and safe operation of the equipment observe the following instructions thoroughly TV sets require sufficient ventilation to prevent their components from overheating which will cause failure Do not block the ventilation openings at the rear If you place your TV set in a special piece of furniture make sure there is enough space for unhindered air circulation Do not place the TV set in the close vicinity of a heater The TV set has been designed for use in dry rooms Should you use it in exceptional circumstances in the open air example on the balcony in the veranda or tent you must absolutely protect it against moisture dew rain splash water The appliance should not be in contact with liquids or exposed to the risk of dripping or splashing Therefore be careful not to place any object containing a liquid vase glass bottle on or near your appliance Before switching on a cold TV set in a warm room you should wait until any condensation in the screen has dried by itself Maximum am2. AUTO INSTALL menu The first line Norm is selected e Depending on the model of your TV set you ll have to select from the options listed below the one that fits with your country EURO Western Europe Tunisia Morocco Australia New Zealand FR France Luxemburg UK United Kingdom Eire DK Eastern Europe Middle East Africa French DOM TOM Asia Select corresponding option by means of the directional keys Left Right e Select the Start line through the Up Down directional keys ITCOO8_en 3 03 03 16 33 Page 4 e Start the Automatic Channel Set up by pressing the ok key Two new lines appear showing the frequency and programme number on which each new channel found is memorised Wait a few minutes until the Channel Organisation menu ORG appears Channels Organisation The PR line is selected How to change the channel number To identify each channel make use of your TV magazine to find out the actual name of the current programme channel 1 Use the key PR and PR to select the channel number you wish to change 2 Press the new channel number compulsorily 2 digits for ex for Channel 2 enter 0 then 2 on the remote control You can also use the directional Left Right keys 3 Validate with key ok The corresponding programme is now stored under the new channel number How to delete a channel number Delete any programme the picture quality of which appears to be poor
3. S Vid o sockets 3 sur mod les quip s The Audio Video sockets allow you to connect a VHS or 8 mm camcorder The Audio S Video sockets allow you to connect a VHS or Hi 8 camcorder To view images produced by an appliance connected To the AVI peritel socket press the AV key to select AVI or AVIS in the case of an S Video appliance To the AV2 peritel socket press the AV key to select AV2 or AV2S in the case of an S Video appliance To the Audio Video S Video sockets press the AV key to select AV3 or AV3S in the case of an S Video appliance On some models AV3 and AV3S are not accessible in this case select AV2 or AV2S in the case of an S Video appliance Some appliances connected to the AV1 or AV2 sockets automatically produce a switching signal Therefore you do not need to press the AV key to make a selection Not to degrade the picture and sound quality do not turn on the devices connected to the scart socket and to the Audio Video socket at the same time VIDEO LAUDIOR S VIDEO The Headphone socket 4 f included The headphone adapter allows you to connect a stereo headphone or earphone plugs the loudspeakers sound is then muted Volume may be adjusted through keys VOL ITC 008 EN BEI RDG 03 03 2003
4. the TV set flashes The keys of the TV set are now locked and switching it on again will be possible by means of the remote control only Keep the remote control out of the reach of children To unlock the keys of the TV set make use of the number keys on the remote control The keys of the TV set will also remain locked after timer programmed switching off The lock function will also be activated when the TV set is switched on standby or switched off with its On Off switch before the time remaining until programmed switching off is over How to switch off the set To switch the TV set off press the key on the remote control or use the On Off switch on the TV set The TV set automatically switches to stand by after a few minutes without telecast on the selected channel Important The display SIGNAL 0 on the grey screen means that you are on an AV programme and that the TV set is not receiving any signal p The Videotext How to use Videotext If included Press the key TEXT to display the Summary page 100 Calling up a page Enter the 3 digits of the number e g 150 170 of the page you want to read After a few moments the page will be displayed To visualise the next or previous page press the directional keys PR PR For direct access to pages the numbers of which are displayed in the colour rectangles at the bottom of the page press the corresponding colour key To access p
5. 1 Select the channel with the key PR and PR 2 Select line Hi using the Up Down directional keys 3 Press and hold down the ok key the channel is deleted Prior to leaving the menu you should check whether the programmes are stored in the order you prefer Once your channels are duly sorted close the menu through EXIT You may recall this menu by pressing the MENU key 2 times for the mono TV sets 3 times for the stereo TV sets Note For channels diffusing teletext in Czech Slovak Rumanian Croat Russian or Greek After having tuned in the channel display the manual channel set up menu see page 5 Select the Text line by pressing 5 times on the Down button of the remote control Select the number of the character table using the table on page 7 Memorise it with ok and then quit the menu with EXIT ITCOO8_en 3 03 03 16 33 Page 5 p Manual Channel Set up Adjusting the Picture With the manual set up 1 Display the INSTALL menu by pressing MENU on the remote control unit Twice for mono TV sets Three times for stereo TV sets The first line Auto is selected 2 Select the Manual line using the Up Down directional keys 3 Press ok to display the manual installation menu MAN INSTALL The first line Norm is selected Depending on the model of your TV set you ll have to select from the options listed below the one that fits with your country EURO Wes
6. VD player play functions RC 311TA1G only About the TV set Prior to enjoying your TV set you ll have to set it up i e to find and store the channels which may be received in your area The Automatic Channel Set up will look for all the channels and number them Since the channel numbers assigned to the programmes by the Automatic Channel Set up do not necessarily correspond to the actual number of the channels example Channel 4 you may change them upon completion of Automatic Channel Set up How to switch on the set With the On Off button fitted on the set When the red LED is lit the TV set has previously been switched on standby with the key on the remote control To switch the TV set on again type in a channel number Automatic Channel Set up With the Automatic Channel Set up e When a VCR or satellite receiver is connected to the aerial socket you must switch on this equipment Should external equipment be connected to the TV set via the SCART socket it must be turned off The first time you switch your TV set on the automatic installation AUTO INSTALL will automatically appear If it does not you will find this menu by pressing a number of times on the remote control MENU key 2 times for the mono TV sets 3 times for the stereo TV sets The installation menu INSTALL is displayed and the Auto Install line is selected Press the ok key on the remote control unit to display the
7. age scrolling Games Zoom and Display functions you must first press the MENU button to display the corresponding panel at the bottom of the Fastext page Page Scrolling You may stop the page scrolling with the red key This has the effect that STOP is displayed instead of the page number When pressing the red key again page scrolling will start again Prize competitions By means of the green key you can either display or hide the solutions Zoom With the yellow key you can subsequently enlarge the upper and the lower half of the screen page and then switch back to full screen page display Videotext display The blue key enables you to superpose a videotext page on the standard TV picture and to switch back to the standard TV picture Fastext When videotext pages are broadcast as per the Fastext standard you can use the corresponding colour keys to select one out of the 4 headings displayed in the footer Selection of a given heading may have the effect to display further headings Certain programmes use videotext to broadcast subtitles as well as constantly updated news These pages can be found in the videotext summary Once you have found the page the subtitle and or news will be superposed on the TV picture 7 ITCOO8_en 3 03 03 16 33 Page 7 Temporary modification of the character set table for teletext You can temporarily modify the character set table for teletext While the navigator banner is displa
8. bient temperature 35 Maximum humidity 85 In the evening after TV programmes or in case of a long absence it is recommended to turn of the apparatus at the main switch Even when the On Off switch is in the Off position and even though it does not consume any current the television is not completely separated from the mains supply In order to completely disconnect it is necessary to unplug the mains plug ITCOO8_en 3 03 03 16 33 Page 1 The mains plug must be easily accessible In the following cases we recommend that you pull out the mains connector 1 During a thunderstorm In such a case it is advisable that you also disconnect the TV set from the aerial socket 2 When odour or smoke emanates from the set Never attempt to open your TV set yourself Further information The TV set shielding is sufficient to prevent X radiation to the exterior Any operation performed by a non skilled person change of high voltage or replacement of the picture tube by a model not complying with the manufacturer specification are likely to cause considerable increase in X radiation ATV set modified in such a way no longer complies with the manufacturers specification and must not be used About cleaning The screen is to be cleaned with liquid glass cleaners e Never use abrasive products e Clean the cabinet with a soft cloth soaked with neutral cleaner Do not use solvents such as white spirit or alcohol based
9. cleaning products since they may damage your television e At regular intervals clean the ventilation grids at the rear of the TV set About degaussing The terrestrial magnetic field may have an influence on your TV set This influence is revealed by the coloured spots which appear on the screen Should this be the case e Turn the equipment off by means of the On Off switch e Wait about one hour before switching the set on again This procedure performs automatic degaussing of the screen Should there still be coloured spots on the screen repeat the operation p ITCOO8_en 3 03 03 16 33 Page 2 To set up your TV set follow the instructions on this page before you continue with the channel set up procedure described on page 4 1 Put the batteries in the remote control unit PRECAUTIONS ON USING BATTERIES Inserting batteries 2 x LR 03 AAA 1 Only use the battery types specified Make sure you use the correct polarity Do not mix new and used batteries Do not use rechargeable batteries Do not expose batteries to excessive heat throw them on the fire recharge them or try to open them as this could cause them to leak or explode Remove the batteries from the remote control if you are not using it for a long period of time several Please respect the environment and gt prevailing regulations Before you dispose of batteries or accumulators ask gt lt your dealer
10. nel number assigned to it VCR s without an integrated modulator do not require this setting 4 Continue on page 4 Channel set up Remote Controls RC 111TA1G and RC 311TA1G Depending on the model of remote control supplied with your TV set you can also use it to operate most DVD players and recent video recorders made by Thomson Saba Brandt Ferguson and Telefunken eo mD aa INFO 008 00 0 0 Oxs G B8 0 BE BOD 2 Bi ITC008_en 3 03 03 16 33 Page 3 p Press the key corresponding to the appliance you want to operate RC 311TA1G only To switch your machine on off stand by Personal Adjustments PRESETS Timer ZZZ LIST Display of channel stand by time INFO Videotext keys TEXT The colour keys can also be used to operate teletext Directional keys Up Down Left Right for selection and validation key ok EXIT for erasing the menu windows or information from the screen MENU is for calling up the menu windows Volume control Mute Programme change For channel selection and number input in the menus For 2 digit channels 10 11 12 etc first press twice on key 0 of the remote control for ex for 12 press 00 then 12 To select one of the appliances connected via the AV sockets Video recorder play and record functions and D
11. o Stereo Mono Dual SI S2 Mono Auto Mono Son AV Stereo SI 52 If you want to preserve these adjustments as preferred settings press the red key during 3 seconds to store them You ll then be able to recall them later on Close the menu through EXIT Settings are stored until you proceed to another change h How to switch on the set With the On Off button fitted on the set When the red LED is lit the TV set has previously been switched on standby with the key C on the remote control If the red LED flashes it means that the control keyboard of the TV is locked and can only be made operational again through the remote control In both cases enter a channel number How to select a channel Through the digital keys of the remote control For two figure channels 10 11 12 etc press the 0 key on the remote control unite twice appears on the screen Through the digital keys enter the tens unit digit then the unit one you can also quickly enter the two digits With the PR or PR button of the remote control or the keypad If you change the channel with the PR or PR buttons of the keypad maintain the button pressed until the next or preceding channel appears on the screen How to adjust the volume With the remote control by making short pulses or maintaining the VOL buttons pressed With the keypad of the television by maintaining buttons VOL pre
12. ssed How to mute the sound With the key Press once more on the key to reactivate the sound Operating the zoom Using the Left Right directional keys select 4 3 format 14 9 zoom 14 9 letterbox format 16 9 zoom 16 9 letterbox format 16 9 zoom subtitles 16 9 letterbox format subtitles Cinerama zoom optional 16 9 format Zoom functions are only available on 16 9 TV sets 6 ITCOO8_en 3 03 03 16 33 Page 6 p How to display the channel number With the JNFO key display or remove the channel number and if you want it the time left before timer programmed switch off How to recall the preferred settings Press on the red key to recall the sound and picture settings you previously stored see page 5 How to programme a switch off Press on the Green ZZZ LIST key then using the Left Right keys adjust on the screen the wished for duration before the switching off of the TV set by intervals of 5 minutes up to 4 hours To exit the menu press EXIT When the programmed remaining time is over the TV set will switch on standby To cancel first press the Green ZZz LIST and then by means of the directional key Left reset the time remaining on 00 00 The programmed switching off is also deactivated when the TV set is turned off through its own On Off switch How to prevent kids using the TV set Hold key C on the remote control down for over 5 seconds until the red LED on
13. tern Europe Tunisia Morocco Australia New Zealand FR France Luxemburg UK United Kingdom Eire DK Eastern Europe Middle East Africa French DOM TOM Asia 1 Select corresponding option by means of the directional keys Left Right 2 Select the Freq line through the Up Down directional keys 3 Start the set up in a decreasing or increasing order by means of the Left Right directional keys When a channel is found the pictures appear If the picture quality is poor make use of the directional keys Up Down to select the line gt lt and try to improve picture quality with the directional keys Left Right 4 Then select the PR line through the Up Down directional keys and enter the channel number corresponding to the pictures You may also use the Left Right keys 5 Store the programme by pressing ok To find the next programme re start Channel Set up by means of the directional keys Left Right 6 Select the Decod line through the Up Down directional keys 7 If the station is encrypted and if you want to connect a decoder to the AV socket tick the box with the Left Right keys 8 Select the Text line through the Up Down keys and choose the character set table to be used for videotext 1 Western Europe 2 Eastern Europe 3 Russia Bulgaria 4 Greek 5 Arab 6 Ukrainian 7 Bielo Russian Use the table on page 7 to guide you Display the Image menu by pressing MENU on
14. the remote control unit Once for mono TV sets Twice for stereo TV sets Through the Up Down keys select the function you want to adjust Brightness Colour Contrast Sharpness Tint Adjust with the Left Right keys Adjustment of tone is only possible and necessary for an NTSC image If you wish to preserve these adjustments as preferential press the red button to memorise them You ll then be able to recall them later on Close the menu through EXIT Settings are stored until you proceed to another change Adjusting the Sound only on stereo models Press the MENU key to display the menu Select the function to be adjusted Treble Bass Balance Mode using the Up Down directional keys then adjust using the Left Right keys I Adjust the treble level F Adjust the bass level tual Adjust the balance between the left and right paths SIE Choose the type of sound see table below AVL This functions tones down loud sound effects It is particularly useful when watching TV late in the evening for instance To activate the function tick the box by pressing ok Dolby Virtual Tick the box to take advantage of optional Virtual Dolby Surround When you do this the surround effect control bar is displayed Select the line and adjust the surround effect Sound received Options NICAM Stereo Stereo Stereo Mono NICAM Dual SI S2 S3 NICAM Mono NICAM Mono Stereo Stere
15. whether they are subject to special recycling and if he accepts to weeks take them back 2 Connect the TV to a mains socket The mains plug carries the power supply to your TV 2 set It should only be connected to an AC supply at 220 240 V 50 Hz It must not be connected to a DC supply If the plug is detached from the cable do not under any circumstances connect it to a mains socket as there is a danger of electrocution a5 1a 0S Continental Europe UK SOCKET United Kingdom Equipment for the UK is supplied with a mains cable fitted with a moulded plug The plug contains safety components and must not be replaced by a type sold in shops It is fitted with a fuse that protects your television If your set no longer works the fuse may have blown If it has replace it with an identical ASTA certified or BSI BS 1362 5 amp fuse 3 Connect the outside aerial or cable network to the F socket at the back of the TV set 3 The aerial socket is for connecting an external antenna or equipment fitted with a modulator VCR satellite receiver etc When connecting additional equipment to the aerial socket you must assign a channel number to it To do so switch the external equipment on then search for its modulator channel on the TV set assign the Cc channel number found to the equipment and store Ww From now on every time you want to use the external equipment connected you must select the chan
16. yed press ok In the green rectangle is replaced by TXT 1 Using the green key choose the correct table number for the teletext on the screen The TV set will automatically return to the character table selected in manual set up page 5 the set is switched off the channel is changed Leave the videotext through EXIT Connections The scart cable AV1 1 The scart cable AV1 allows you to connect a VCR or camcorder VHS 8 mm a Canal decoder a video game machine or devices supplying a RGB signal You may also connect a digital decoder cable earth satellite an analog satellite receiver or a DVD player If your TV set is equipped with a single video socket you can also connect a video recorder or an S VHS or Hi 8 camcorder to it The scart cable AV2 2 If included The scart cable AV2 allows you to connect a VCR or camcorder VHS 8 mm S VHS or Hi 8 You may also connect a digital decoder cable earth satellite an analog satellite receiver or a DVD player When you turn off the connected device and if you have not changed channel during viewing the TV set automatically returns to the previously watched channel If the TV set has been turned on by the VCR it will return to stand by as soon as the VCR is switched off ITCOO8_en 3 03 03 16 33 Page 8 p Front Audio Video
Download Pdf Manuals
Related Search