Technicolor - Thomson Ferguson T 7025 UD User's Manual
Contents
1. FERGUSON T 7025 UD COLOUR TELEVISION WITH NICAM DIGITAL STEREO SOUND AND FASTEXT FERGUSON OPERATING INSTRUCTIONS About this manual This document is common to several television models Therefore certain functions or settings may not apply to the model you have purchased About the switch The position of the ON OFF switch differs depending on the model It may be located on the front or on the right hand side of your set see the drawing inside the cover page of your manual About safety To ensure your own safety and safe operation of the equipment observe the following instructions thoroughly TV sets require sufficient ventilation to prevent their components from overheating which will cause failure Do not block the ventilation openings at the rear If you place your TV set in a special piece of furniture make sure there is enough space for unhindered air circulation Do not place the TV set in the close vicinity of a heater The TV set has been designed for use in dry rooms Should you use it in exceptional circumstances in the open air example on the balcony in the veranda or tent you must absolutely protect it against moisture dew rain splash water Before switching on a cold TV set in a warm room you should wait until any condensation in the screen has dried by itself Maximum ambient temperature 35 C Maximum humidity 85 By the end of your TV evening or w2. London amp South East Bluebell Hill Crystal Palace Dover Heathfield Oxford South West Beacon Hill Caradon Hill Huntshaw Cross Redruth Stockland Hill Channel Islands Fremont Point South Hannington Midhurst Rowridge West Mendip East Sandy Heath Sudbury Tacolneston Midlands Ridge Hill Sutton Coldfield The Wrekin Waltham North Belmont Emley Moor North West Caldbeck Winter Hill North East Bilsdale West Moor Chatton Pontop Pike Scotland Angus Black Hill Sandale Caldbeck Craigkelly Darvel Durris Eitshal Keelylang Hill Knock More Rosemarkie Rumster Forest Selkirk 12 40 260 50 49 57 57 22W 55 51 33 51 39y 61 31v 58y 31v 51v 62y 22 46y 26 58y 22W 46 33v 56 52 63y 63 28y 62 44 26 44 45y 55 24y 64y 270 44y 55y 28 40y 33 64y 28y BBC 1 BBC2 ITV 43v 23v 66y 64y 60y 60y 25y 59y 41y 23v 41y 420 58y 270 61y 24y 41y 59W 25y 43y 23v 6ivy 25y 470 28y 59 29 CH4 65y 30y 53V 67y 53v 53v 32y 65y 477 29y 470 66y BBC1 BBC2 Wales Blaenplwyf 31y 27W Carmel 57 63 Llanddona 577 63V Moel y Parc 52 45 Presely 46 40 Wenvoe 44y 5iv Northern Ireland Brougher Mountain 22 28 Divis sly 27y Limavady 55 62 i 5 So Orkney Keelylang ie bhnds o Fremont Point Presely Carm Wenvoe Rumster Forest Moor Phe Wrekin e Waltham Sutton Sandy H
3. a channel which broadcasts teletext The time is set automatically and is displayed after the channel number Exit the menu using exit 14 INSTALLATION MAIN MENU Exit Manual programming Auto installation Programme organisation gt Personal settings PERSONAL SETTINGS Return Menu language English Country UK Auto volume level m AV1 name AV2 name AV3 name Prog to be used for reference time Select a station from which you want to get the reference time Select the line marked Return to return to the previous menu Preferences 1 Display the SUMMARY by pressing and releasing the menu key on the remote control 2 Select the line marked Preferences 3 Display the menu using ok Make your choice from the proposed PREFERENCES Se options Use the information below to help Return you Show program number lt b WY Show program number AV2 video input Video If you wish to permanently display the number AV3 video input S Video of the programme you are watching tick the box Format control Auto using the Left Right keys Press the Left Right Picture preferences keys again to deactivate this function AV2 video input Use the Left Right keys to select the type of video signal received at the AV2 SCART socket Video or S Video AV3 video input Use the Left Right keys to select the type of video signal received at the AV3 sockets these sockets are located on the front or the side of the televisi
4. then select the type of sound you desire Sound mode 2 The choices available to you depend on the type of sound you previously selected The Magic and Dolby Virtual modes are only available in stereo if the Surround line has notbeen activated in the SOUND SETTINGS menu Select this line then choose the desired mode using the Left Right keys Treble centre Bass centre These lines appear according to the se Sound mode selected Select each of the lines and set the bass and treble of the central channel Surround effect This line appears only if you have selected Sa Dolby Virtual on the Sound mode ine Select this line and adjust the surround effect to suit you Treble Bass Select each of these lines and adjust to suit you Exit the menu using exit Return Automatic Normal Sound type Sound mode Balance L R Treble Bass Surround effect 1 Broadcast Choice mono automatic mono stereo mono stereo dual sound 1 sound 2 NICAM 3 sound 1 sound 2 sound 3 AV stereo sound 1 sound 2 2 Mode Effect Normal reproduces the original sound mono or stereo Wide gives a stereo effect on mono sounds Magic accentuates the stereo effects and adds echo Dolby Virtual Virtual Dolby Surround Hall Reverberation effect with rear speakers Pro Logic Cinema sound if the sound is coded in Dolby Surround with rear speakers Virtual Dolby Surround is based on Dolby Pro Logic deco
5. been installed even after AUTOMATIC INSTALLATION 1 Press and hold menu the SUMMARY is displayed first followed by the INSTALLATION MAIN MENU 2 Select the line marked programming 3 Display the menu using ok 4 Now continue by following the messages at the bottom of the screen For further details read the information below Standard Select the standard using Left Right keys that corresponds to your country from the list of standards The number of standards proposed will differ from one model to another Manual INSTALLATION MAIN MENU Exit gt Manual programming Auto installation Programme organisation Personal settings MANUAL PROGRAMMING Return Standard France for France and Luxemburg z DKK eg for Eastern Europe and Reception the Middle East Autosearch l for the United Kingdom and Fine tuning Ireland Store on PR number Euro BG for Western Europe Name Decoder Reception Your television can pick up channels either via External sound pathi an aerial RF channels or via a cable network Certain cable networks use the same frequencies as the RF channels If this is the case you must select Aerial instead of Cable Autosearch Enter the programme number if you know it If not search using the Left Right keys Your television will stop at the first channel it tunes into If you wish to memorize it go to the line marked Store on PR number If not resume the search using the Left R
6. border area 4 Then validate using ok 5 A welcome message is displayed 6 Run the automatic installation sequence using ok 7 A message appears to inform you that automatic installation has started Fig 3 Wait for a few minutes A new message will inform you when automatic installation is completed 8 If you wish to check or modify the channel organisation press ok and see the Programme organisation chapter If you do not wish to modify the channel organisation you can exit the menu by pressing exit then watch the channel of your choice Choose the desired channel using the number keys 1 2 3 and the pr pr keys If you_have_a decoder see the Manual programminglchapter Your television will only search for channels corresponding to the country you have selected See the Manual channel programming chapter to install any channels not found For cable networks read the chapter to install any channels not found The list of languages and countries may vary from one model to another Installation Instructions end Fig 1 English gt Francais Deutsch Italiano Espanol Portugu s Nederlands Svenska Dansk Norwisch Fig 2 Exit United Kingdom Eire gt France Germany Italy Spain Portugal Holland Belgium and Luxembourg Switzerland Austria Sweden Denmark Norway COUNTRY SELECTION Other Select your country and press OK SEARCHING AUTO INSTALLATI
7. operate satisfactorily it should then be reported to the dealer from whom it was purchased who will normally be able to provide service and make any claim under guarantee on your behalf 3 If it proves impossible to contact the dealer you should contact the Thomson multimedia Limited Service Depot for advice stating the model and serial numbers date of purchase and the name and address of the dealer from whom it was bought 4 This guarantee is effective in the United Kingdom only 5 Thomson multimedia Limited reserves the right to vary the specifications of the equipment without notice Picture Tube Guarantee The colour picture tube is separately guaranteed for twelve months free or four years optional extra requiring registration Ask your dealer for full details at the time of purchase This Guarantee in no way affects any statutory right of a consumer THOMSON multimedia CROWN ROAD ENFIELD MIDDLESEX EN1 1DZ FERGUSON is a registered trade mark FOR COMPLETION BY THE PURCHASER Purchaser s name 0 00 e eee eee atolo lde e A ised haben tie ie dee es PLEASE NOTE It will not be necessary for the dealer or purchaser to return this guarantee to Thomson multimedia Limited when making a claim under guarantee unless requested to do so provided that the model and serial numbers date of sale and the purchaser s name and address are quoted on the order or advice note FOR COMPLETION BY THE DEALER
8. used see the sec tion headed Basic connections FAST FORWARD SEARCH If this button is pressed and held in during playback fast picture search forward will be obtained Fast forward will be obtained if the recorder is in Stop mode STOP Press to stop tape movement PAUSE STILL Press during playback for pause RECORD Press to start recording PR PR VCR Programme selection Press to switch on or on Stand By Navigation principles Calling up the INSTALLATION MAIN MENU If there is no menu displayed on the screen press and hold the menu_ key on the remote control The settings SUMMARY is displayed first followed by the INSTALLATION MAIN MENU which you can use to operate your television Calling up the SUMMARY Press and release the menu key on the remote control to display the list of menus available for using your television functions or adjusting your television Calling up a Menu Select the menu you wish using the Up Down keys Press the OK key to validate Navigating within the Menus Use the Up Down keys to select a line Use the Left Right keys to Increase or decrease a value for example Fine tuning lt gt mmm Select an option for example Reception lt gt Aerial Reception lt gt Cable Activate or deactivate an option for example Decoder D gt M Access a sub menu for example Picture preferences gt You can use the Ok key to Activate
9. 75W Pin 19 pin 17 return SIGNAL SELECTION Facilities are provided for automatic switching when the equipment connected provides switching voltages as follows Pin 8 9 5 V to 12 V Auto switching to auxiliary O AUX channel 4 5 V to 7 V 16 9 display Pin 16 1 V to 3 V Auto switching to RGB SIGNAL LEVEL Composite video 1Vp p 3dB in out positive going 75 W Sync 0 3 Vp p 3dB 10 dB negative going 75 W RGB input 0 7Vp p 34dB positive going 75 W Audio in out 0 5 Vrms nominal Input impedance 10 kW 20 Hz 20 kHz Output impedance 31kW 20 Hz 20 kHz 23 Guarantee This guarantee is automatically effective from the date of purchase of the equipment The appropriate sections should be completed by the dealer and purchaser at the time of purchase This guarantee should then be retained by the purchaser and kept safely so that it may be referred to and produced if required should a claim be made during the guarantee period Terms of Guarantee 1 The component parts used in this television receiver with the exception of the colour picture tube are guaranteed by Thomson multimedia Limited against failure due to faulty material or workmanship for a period of one year from the date of purchase The colour picture tube is guaranteed separately for one year unless extended at the time of purchase see Picture Tube Guarantee 2 Should the equipment fail to
10. Call up Teletext Toptext Fastext function purple button Press to operate the TV set Press to operate the VCR Move Up Down in menus Go to adjustment function MENU _ Volume adjustment Video recorder functions Change programme Selecting appliances connected to the television AV1 AV2 Sound mute Go to programmes and enter numerical values in menus For programme numbers higher than 10 press the 0 key on the remote control appears on the screen Now use the number keys on the remote control to enter first the tens digit then the units digit Please respect the environment Before throwing any batteries away consult your distributor who may be able to take them back for specific recycling Remote control Video Recorder Functions Video cassette recorder commands using TV remote control unit Selected Ferguson Video recorders can be operated by direct infra red remote control This facility will be referred to in the appropriate video recorder operating instructions Contact your Ferguson dealer for more details VCR Cs Press to operate the VCR REWIND SEARCH If this button is pressed and held in during playback fast picture search reverse is obtained Rewind will be obtained if the recorder is in Stop mode PLAY Press to start playback When a scart socket is
11. MODEL No ccc cece eee eee SERIAL No cece cece eee eee DATE OF PURCHASE Dealer s stamp or name and address This publication is printed on 100 recycled paper 253 543 30
12. ON Coecccccccocce 03 STATIONS FOUND Searching for TV stations Please wait To cancel press EXIT Automatic installation The Automatic installation function is useful if you have to go through the installation procedure again such as when moving house This function deletes all previously memorised programmes To install a new channel you should use the Manual programming function Before running AUTO INSTALLATION check the PERSONAL SETTINGS menu to ensure that the country displayed is correct N Your television will only search for channels corresponding to the selected country so see the Manual amp programming chapter to install any channels not found For cable networks if you have not found certain channels select Other instead of a country name in the PERSONAL SETTINGS menu then run automatic installation again 1 Press and hold the menu key on the remote control to display the INSTALLATION MAIN MENU The SUMMARY appears first followed by the INSTALLATION MAIN MENU 2 Select the Auto installation line 3 Validate using ok A message will inform you that Automatic installation has begun Wait for a few minutes A new message will inform you when Automatic installation is completed If you wish to check or reorganize your channel display press the Ok key and see the Programme organisation chaptc If you do not wish to reorganize your programmes you can exit this menu by pressing exif then wa
13. ality in your own home with a coded Dolby Surround signal or you can enjoy special sound effects with a stereo or mono signal by connecting 2 pairs of loudspeakers on some models one pair of speakers or simply using the sound facilities of the television set Turn on the main switch and connect the speakers to the appropriate sockets The black terminals of the speakers must be connected to the black terminals of the television set likewise for the red terminals see Speaker Connection page 22 Display the SUMMARY using the Menu key on the remote control Select the line marked Sound Validate using ok The SOUND menu is displayed Select and set the proposed options Use Sei the information below to help you Sound settings Use this menu to set the sound effect of your television To display the SOUND SETTINGS menu select the line and press ok According to your set up activate the external bass box Ext subwoofer line the external line Ext amplifier line the rear speakers Surround line Test balance Activate this function then set the following to the same sound level according to your set up the balance between the left and right channels Balance L R line the volume of the central channel Centre volume line the volume of the rear speakers Surround volume line Return To return to the SOUND menu Ext amplifier Return Sound settings Stereo Pro Lo
14. d Personal settings Display the menu using ok 4 Continue by following the messages at the bottom of the screen o For further details read the information below Menu language Select the language in which the menus are to be displayed Country Indicate the country in which you are if you wish to rerun Automatic Programming For cable networks if certain channels have not been found select Other instead of the country name before run R ning automatic installation again Q You may find that the characters of cer tain teletext languages are inaccess ible for the selected country Auto volume level This is a sound control function which aims to equalise the volume level between different channels and between different programmes on the same channel Activate or deactivate the auto volume level as required R On models equipped with Dolby d Surround this function remains inactive if Dolby Virtual or Pro Logic has been selected in the SOUND menu see Volume Control AV1 AV2 AV3 name Use these to give a name to each of your audio visual programmes Select the character you wish to modify using the Left Right keys Use the 1 or 2 keys to display the desired character Prog to be used for reference time To display the time using the info key or to use the alarm function the television clock must be set to the correct time Select the line marked Prog to be used for reference time and select
15. ding for the reproduction of the Left Right Centre and Virtual Surround sound channels using two loudspeakers Dolby Pro Logic and the double D symbol are trademarks of the Dolby Laboratories Licensing Corporation Manufactured under licence from Dolby Laboratories Licensing Corporation 17 BEUA Picture Adjustment PICTURE Display the SUMMARY using the menu key on the remote control Select Picture Validate Return using Ok The PICTURE menu is displayed Select and set the proposed options Use the information below to help you Contrast Brightness Colour Contrast Sharpness Sharpness Select each of these lines one after the other and set as required Contrast expand Contrast expand Tone Select this line then choose the desired Contrast Select the line marked Return to return to the previous expand setting High or Low menu Tone Select this line then choose the desired colour tone Warm Neutral or Cold Exit the menu using exit List of Channels the number of programmes memorized For each programme the list indicates the station name or type and the programme number The 3 AV programmes are listed on page 11 A This list contains up to 10 pages The number of pages depends on To display the list press the list key on the remote control or Display the SUMMARY using the menu key on the remote control Select the line marked List Validate using ok The page dis
16. eath 2 Coldfield Rowridge Channel Blands S Belmont Ridge Hill Crystal ITV CH4 24 21 60y 53y 60y 53y 49y 420 43y 50y 41y 477 25y 32y 24y 21y 59y 65W Sudbury vy Already transmitting NICAM Manual Programming Channel number guide Ireland In addition to the RTE main transmitters listed there are many RTE transposers throughout the country If your area is not covered by a main transmitter and you are not sure of the channel numbers of your local transmissions your television dealer is the best person to advise you He will also know whether you need a horizontal or vertical aerial to suit the transmissions REPUBLIC OF IRELAND RTE1 RTE2 North West Holywell Hill Truskmore North East Clermont Carn East Kippure Dublin amp East Three Rock West Maghera Central Cairn Hill South West Mullaghanish South East Mount Leinster NORTHERN IRELAND BBC1 BBC2 UTV CH4 23 26 Brougher Mountain 22 28 25 32 09 1 07 G Divis 31 27 24 21 Limavady 55 62 59 65 52 56 08 H 10 J WALES BBC BBC2 HTV S4C 29 33 WALES Presely 46 40 43 50 02 B 08 H 40 43 04 D 07 G 06 F 09 I Hol Hill lywell NORTHER IRELAND Truskmore gs 3 Clermont C4 IRISH REPUBLIC Cairn Hill 13 Personal settings 1 Press and hold the menu key the SUMMARY is displayed first followed by the INSTALLATION MAIN MENU 2 Select the line marke
17. en the television is locked the red power will be light flashing The television can now only be operated from the remote control To release the lock press any number key on the remote control Switching Off the Television To switch off the television press the Standby key on the remote control or press the ON OFF switch on the television set 20 Teletext R Certain channels broadcast an electronic news page service with a range of different information services The presentation and use of the Teletext differ from one country to another and from one programme to another Teletext Fastext or Toptext Press the text key to display the Teletext Index page 100 A message will inform you if the programme you are watching has no Teletext service To call up a page Enter the 3 digits of the page number you wish to consult for example 150 or 170 After a moment the page appears Use the Left Right keys to consult the next or the previous page Standard Functions Rolling pages Some information is displayed over several sub pages It is scrolled on your screen as it is received To stop scrolling select STOP using the Up Down keys and validate using Ok Press Ok again to continue scrolling Masked text To reveal a hidden answer for example in a quiz programme select using the Up Down keys and validate using Ok Press Ok again to hide the answers Zoom Select ZOOM using the Up Down keys then press the Ok key o
18. f the On Off switch e Wait about one hour before switching the set on again This procedure performs automatic degaussing of the screen Should there still be coloured spots on the screen repeat the operation amp The pages of this publication are printed on recycled paper Installation Using the remote control and fitting the batteries About this manual 1 About the switch 000 1 ABOUtSATCLY ixcuns acacia 1 About cleaning 000 1 About degaussing 1 Basic connections 000000e 3 TV VCR Antenna connections 4 TV FAMENNE cecnccsanennneeae ee cans 4 TV VCR Antenna 0 4 Remote control cceee eee 5 Television Functions 5 Other Connections 0005 5 Video Recorder Functions 6 Navigation principles 7 Calling up the INSTALLATION MAIN MENU 00200 000 7 Calling up the SUMMARY 7 Calling up a Menu 7 Navigating within the Menus 7 Installing your television for the first time e eee 8 Automatic installation 9 Programme organisation 10 Manual programming 11 Channel number guide 12 Channel number guide Ireland 13 Personal settings 0005 14 Preferences 00cceeeeeeeeeeee 15 How to call u
19. gic Sound type Sound mode Treble centre Bass centre Treble Bass SOUND SETTINGS Return Ext subwoofer Ext amplifier Surround Test balance Balance L R Centre volume Surround volume You can use external amplifiers instead of the television configuration see Speaker Connection page 22 Amplifier with a Dolby Pro Logic decoder Connect the left L and right R CINCH plugs from the television set to your amplifier If there are rear speakers Surround disconnect them from the television set Select Normal mode from the SOUND menu Set the sound using the amplifier 16 Stereo amplifier Connect the left L and right R CINCH plugs from the television set to your amplifier Connect the rear speakers Surround to the television set Activate the Surround line in the SOUND SETTINGS menu Setthe sound of the Left and Right channels using the amplifier and the sound of the Center and Rear channels Surround using the television set SOUND SETTINGS menu In both cases activate the Ext amplifier function to cut the Left Right and Center channels of the television set if you have also activated the Surround option the central channel is not cut A Note If you do not connect an external amplifier cancel this option e Otherwise you will have no sound Sound type 1 The choices available to you depend on Sei the broadcast Select this line
20. hannel you wish to delete Return select the line marked Delete program 4 Press Ok to delete the programme SARE L EU 5 Validate using ok Swap with PR Change pr name Delete program PROGRAMME ORGANISATION To organize your channels to suit you 1 Select the line marked Select program 2 Use the pr pr or Left Right keys and the programmes logos to find the programme Select programme number using to which you wish to give the No 1 PR PR or lt gt or 0 to 9 keys Its present number appears on the line marked Select program Select the line marked Return to return to the previous 3 Select the line marked Swap with PR menu Enter 01 A 5 Press Ok The two programmes swap position and the desired programme becomes N 1 6 Repeat the above procedure for the other channels To name your channels 1 Select the line marked Change pr name 2 Select the character you wish to modify using the Left Right keys 3 Use the 1 and 2 keys to display the letter you require The name you have entered will be memorised when you move to another line or exit the menu R If you wish to change the order in which A your programmes are displayed or if you wish to name other programmes repeat the procedures described above When you have finished organizing the programmes exit the menu using exit 10 Manual programming The manual installation function is useful if some programmes have not
21. hed off The television automatically switches to 16 9 format if the connected appliance delivers the corresponding signal Continental Europe D ra 220 240 V United Kingdom The plug is fitted with a fuse which protects your television If your television does not work the fuse may be blown In this case replace it with an identical 5 Amp ASTA or Ir BSI BS 1362 certified fuse Note the mains lead of your television is fitted with a moulded plug This lead contains all the safety equipment so you are advised when replacing it not to use a non specific commercially available model TV VCR Antenna connections In order to avoid any interference use the male to male adaptor and the male to female cable supplied with your TV set as shown below TV Antenna J W f Male to male adaptor Male to female cable TV VCR Antenna Ie to female cable supplied with TV Remote control Television Functions Display of channel time sound yellow button and zoom for models with zoom Call up programme list green button Fastext or Toptext headings red button picture freeze for models with this function Right Left Selection within menus and Zoom Function for models with this function To leave a menu or Teletext n sT NFO ENC This key is active only when using the Teletext blue key Standby
22. hen away from home for a longer period we recommend that you turn off the TV set with the On Off switch The mains plug must be easily accessible In the following cases we recommend that you pull out the mains connector 1 During a thunderstorm In such a case it is advisable that you also disconnect the TV set from the aerial socket 2 When odour or smoke emanates from the set Never attempt to open your TV set yourself Further information The TV set shielding is sufficient to prevent X radiation to the exterior Any operation performed by a non skilled person change of high voltage or replacement of the picture tube by a model not complying with the manufacturer specification are likely to cause considerable increase in X radiation A TV set modified in such a way no longer complies with the manufacturers specification and must not be used About cleaning The screen is to be cleaned with liquid glass cleaners e Never use abrasive products Clean the cabinet with a soft cloth soaked with neutral cleaner Do not use solvents such as white spirit or alcohol based cleaning products since they may damage your television At regular intervals clean the ventilation grids at the rear of the TV set About degaussing The terrestrial magnetic field may have an influence on your TV set This influence is revealed by the coloured spots which appear on the screen Should this be the case e Turn the equipment off by means o
23. ight keys Fine tuning You can use this to improve the picture if the transmitter frequency is out of adjustment Use the Left Right keys to obtain the best possible picture and sound Store on PR number Enter the programme number you wish to give the channel e g 01 for BBC1 Memorise using ok Name If the station has been identified by the transmitter its name will be inscribed automatically You can change the proposed name or enter it if it has not already been identified Select the character you wish to modify using the Left Right keys Use the7 or 2 keys to display the character you desire Decoder Use the Left Right keys to tick the box if the channel is coded and if a decoder is connected to the AV1 jack External sound path Switch on your decoder If the sound is coded or if you have no sound activate or deactivate the box as required using the Left Right keys Enter channel number or start autosearch with lt or gt Select the line marked Return to return to the previous menu Once you have made all the adjustments you wish to a programme go to Store on PR number and press ok to memorise these Then move on to the next channel Once you have completed your Manual Programming exit the menu using exit 11 Manual Programming Channel number guide Only the main transmitters are listed There are in addition many relay stations and full lists are available from the Broadcasting Authorities 0
24. in from the remote control Current time The current time is given by the Teletext see PERSONAL SETTINGS menu You can also set the time manually using the number keys 0 to 9 on your remote control Wake up timer A If you wish to be woken up by your television on the channel of your choice you must first set the television clock to the correct time see above Use the Left Right keys to tick the box and display the Wake up timer menu A The lines Wake up time Programme number and Daily only appear if you have ticked the box on the line marked Wake up timer Wake up time Use the number keys 0 to 9 on the remote control to set the time at which you wish to be woken Programme number Select the programme you wish to be woken by Daily Tick this box if you wish to be awakened at this time every day Exit the menu using exit Set the television to standby using the D key on the remote control The red indicator light on the television flashes The television will come on automatically at the programmed time and will go off one hour later if you do not use the remote control 19 Selecting Programmes For channels 1 to 9 press the number key corresponding to the desired channel on the remote control For programme numbers higher than 10 press the O key on the remote control appears on the screen Now use the number keys on the remote control to enter first the tens digit then the units digit If yo
25. nce to magnify the top of the screen twice to magnify the bottom of the screen the page will scroll from top to bottom and a third time to return to the normal display Display You can superpose the Teletext page over the TV picture To do this select MIX using the Up Down keys then validate by pressing the Ok key Press again OK to return to the normal display Sub code You can use this to access a sub page directly Select using the Up Down keys Then enter the four digits of the required sub page number R Certain programmes have Alarm pages that you can set to appear at the time you require For example for 15h30 enter 1530 as the sub page number then press exit You must of course leave the television on the programme which is to transmit the Alarm page Index To call up the index page select 100 using the Up Down keys then validate using OK Direct access You can use the yellow and blue keys to directly access the pages indicated in the bar at the bottom of the screen Fastext functions If the Teletext you receive is Fastext a sub menu at the bottom of the screen appears which you can use to select from the 4 headings according to its colour To select a heading press the key of the corresponding colour Toptext functions If the Teletext you receive is TOPtext the pages are arranged into headings and sub headings by subject You can select the first page of a heading directly by pressing the blue ke
26. on Format control Use the Left Right keys to select the desired picture format Auto if the transmitter for 16 9 format TV s or the appliance connected to one of the peripheral jacks delivers the switching signal the television automatically adapts to the transmitted picture format 16 9 manually selects widescreen picture format 4 3 manually selects this picture format If you have selected 16 9 or 4 3 the television will switch back to Auto when you change channels or you Sed switch off Picture preferences To access the PICTURE PREFERENCES PICTURE PREFERENCES menu press ok Return If you wish you can personalize certain Settings ab Personal picture settings Select and set the Brigh ghtness proposed options Use the information Colour below to help you A Contrast Settings Select Standard or Personal Standard corresponds to the factory settings Personal corresponds to the settings that you have entered yourself The lines Brightness Colour and Contrast are displayed only if you have selected Personal on the Settings line Select each line one after the other and enter your required settings You can recall these picture settings by pressing the red key on the remote control Exit the menu using exit Select the line marked Return to return to the previous menu 15 Sound Settings The television set fitted with a Dolby Pro Logic decoder lets you create a cinema studio sound qu
27. or deactivate an option for example Decoder DoW Access a sub menu for example Picture preferences gt Validate an action for example Store on PR number Use the exit key to exit a menu INSTALLATION MAIN MENU Exit Manual programming gt Auto installation Programme organisation Personal settings SUMMARY Exit Teletext gt Picture Sound List Time Preferences MANUAL PROGRAMMING Return Standard l Reception Aerial Autosearch al gt CH Fine tuning Store on PR number Name Decoder External sound path Enter channel number or start autosearch with lt or gt EXIT MENU O OONA D D D Installing your television for the first time First plug the television into a mains power outlet and to the external aerial or a cable network then switch on using the ON OFF switch located on the front or the side of your set When you switch on your television for the first time the language selection menu is displayed Fig 1 If this does not happen set the television to standby then press and hold the pr key on the television until this menu appears Installation Instructions start 1 Use the Up Down keys to select the language in which you wish the menus to be displayed 2 Then validate using ok 3 A list of countries is now displayed Fig 2 Select the country in which you live or the country from which you wish to receive the broadcasts if you live in a
28. p a menu and how to select a gt function a setting or anc gt S option ES ov a Daily viewing 0ceeeeeee 16 Sound Settings 0 16 a Picture Adjustment 18 fe List of Channels 4 18 7 WMC cs comee onan e a 5 aac eae amp ae a 19 fe Selecting Programmes 20 2 Scrolling the Programmes 20 f Audio visual AV Programmes 20 J Volume Control 20 D Muting the Sound 20 Zoom 16 9 models only 20 Displaying Information 20 Television Lock 20 Switching Off the Television 20 Teletext 20sec cece 21 Standard Functions 21 Other Connections 22 Other Possibilities 22 Speaker connection 22 Euro AV socket connections 23 C17 dolby int 3092 GB TBA 16 3 B Basic connections The mains plug 1 supplies power to the television The television must only be plugged in to a 220 240 V 50 Hz power supply It must never be plugged in to a DC source If the plug comes away from the lead never attempt to plug it in this could cause electrocution The aerial socket 2 located on the rear of the television can be used to connect an external aerial or other appliance equipped with a modulator such as a VCR satellite receiver etc If you connect an a
29. peripheral jack AV1 for a VCR into the CINCH AV3 jacks for a camcorder see table below PLAY RECORD CALL Appliance SCART Socket Appliance SCART Socket PROGRAMME VCR Peripheral a AV1 EEEE Camcorder Camcorder Cinches or S Video AV3 Camcorder Speaker connection Fl Internal external speaker gt t i pa If you have connected external side 7 Bema speakers to the television set the ORO anen internal external selection button located at connectors to the external position pushed the rear of the television set close to the AA down Use the point of a pen Side speaker Side speaker eile mm Side speaker Side speaker 22 Euro AV socket connections The socket is shown as viewed from the rear of the TV N NOTE If an unsynchronised TV l picture results after viewing an external source with a fast blanking signal connected to AV this voltage must be removed to return to TV mode VIDEO INPUTS Composite video or sync Pin 20 pin 17 return RGB Red Pin 15 pin 13 return Green Pin 11 pin 9 return Blue Pin 7 pin 5 return VIDEO OUTPUT Composite video AUDIO INPUTS A Pin 6 pin 4 return B Pin 2 pin 4 return AUDIO OUTPUTS A Pin 3 pin 4 return B Pin 1 pin 4 return FAST BLANKING INPUT Pin 16 1 V to 3 V for fast blanking switching
30. played is the page containing the programme you are watching It is identified in the list by the symbol TV To display the next page press the Right key To display the previous page press the Left key If you wish to watch one of the programmes on the page displayed Enter the last digit of the programme number e g for 25 simply enter 5 on the remote control The list disappears and your programme is selected Or Select the programme using the Up Down keys Validate using ok Exit the menu using exit 18 Page lt gt Programme 0 9 BEUA Time You can use this menu to switch your A television on or off automatically at a set time Return Display the SUMMARY using the menu key on Sleep timer the remote control Select the line marked Time Validate using ok The TIME menu is Current time displayed Wake up timer Sleep timer Wake up time Use the Left Right keys to choose how long you Programme number wish to view before the television switches off Daily The television will switch off automatically atthe SHG OPIS period TO cancel set to 00 00 Select the line marked Return to return to the previous One minute before switching off a message will menu inform you that the television is about to go off If you wish to keep it on press any key on the remote control or the local keyboard The television switches to Child lock mode after an automatic stop It can only be switched on aga
31. ppliance to the aerial jack you must give ita channel number To do this switch on the appliance then use the television to find the modulator channel see the appliance manual Now give it a programme number and memorise it sed Manual Programming of channels Then when you wish to use the appliance simply select its programme number on the television This procedure is not required for VCR s not equipped with a modulator The SCART socket AV1 3 located on the rear of the television is intended to connect a VCR or a camcorder VHS 8 mm a Canal decoder a video games console or RGB signal emitting appliances The SCART socket AV2 3 located on the rear of the television is intended to connect a VCR or a camcorder VHS 8 mm S VHS or Hi 8 We strongly recommend the use of this type of connection which gives a better picture quality To use the peripheral appliance that you have connected press the A Vkey on your remote control press once to ae AV2 three times for AV3 see This selection is automatic for some appliances A olay y on a VCR or switching on a satellite receiver connected to AV1 or AV2 will automatically switch on your television When you stop the VCR if you have not changed channels while watching the VCR the television automatically switches back to the channel you were watching beforehand If the television has been switched on from the VCR it switches to standby when the VCR is switc
32. tch the programme of your choice Choose the desired programme using the number keys 1 2 3 and the pr pr keys INSTALLATION MAIN MENU Exit Manual programming gt Auto installation Programme organisation Personal settings SEARCHING AUTO INSTALLATION Coecccccccccoe 03 STATIONS FOUND Searching for TV stations Please wait To cancel press EXIT Programme organisation During automatic installation your television will search for the channel name and assign it a programme number according to the selected country You can use the PROGRAMME ORGANISATION menu to name any channel name not found to change the order in which the channels are displayed or to delete channels for which reception is too poor Follow the messages at the bottom of the screen For further details read the information below R If you wish to access the d PROGRAMME ORGANISATION menu thereafter first press and hold the menu key on the remote control to display the INSTALLATION MAIN MENU the SUMMARY is displayed first followed by the INSTALLATION MAIN MENU then select Programme organisation and validate using ok INSTALLATION MAIN MENU Exit Manual programming Auto installation gt Programme organisation Personal settings To delete a programme for which reception is too poor 1 Select the line marked Select program 2 Use the pr pr or Left Right keys to list your channels 3 When you get to ac
33. u press O while is already displayed the display returns to 0 in which case you can only select s programmes 1 to 9 Scrolling the Programmes You can scroll through the programmes using the pr pr keys Audio visual AV Programmes Press the av key to call the last audio visual AV programme watched Press repeatedly to scroll the audio visual AV programmes on the screen Volume Control Use the volume keys to increase or decrease the volume Muting the Sound Press the key to mute the sound Press again to restore the sound Zoom 16 9 models only This function is useful for 4 3 or letterbox pictures black bands at the top and bottom of the screen Use the Left Right keys to select the desired zoom position ZOOM 0 4 3 picture black bands at the sides FULL SCREEN for a 4 3 picture that fills the screen ZOOM 1 for letterbox pictures Displaying Information Press the info key to display the following information on the screen channel number and name time zoom type of sound Television Lock You can use this function to prevent anyone from switching on the television using the buttons on the television set The buttons on the television set are locked in the following cases If you switch off the set by pressing and holding the YO key on the remote control for more than 3 seconds After a programmed stop If the television is set to standby when the alarm has been set Wh
34. y or the first page of a sub heading by pressing the yellow key Other functions With certain Teletext channels it is possible to have sub titles overlaid on the screen for certain broadcasts as well as certain news flash updates The corresponding page number is indicated in the Telextext index Once you have found the page the sub title or the news flash will be overlaid onto the TV picture The navigation status bar disappears after a few seconds To display it again press the text key To exit Teletext press exit or text 21 The CINCH Video and Audio sockets 1 are provided to 1 connect a VHS or 8mm camcorder The S and CINCH Audio sockets 1 are provided to connect a S VHS or Hi 8 camcorder To use the appliance you have connected press the i av key several times until the AV3 programme is l selected on the screen When you switch off the connected appliance the television will remain on the AV3 programme and you must use the numerical keys on the remote control to select a programme on models equipped with this function The headphone socket 2 is provided to connect a 2 headphone or earphones N Connecting headphones mute the sound from the television loudspeakers Other Possibilities Copying a cassette on models equipped with this function Plug the VCR you wish to record to into the SCART socket AV2 Plug the appliance you wish to copy from as follows into the
Download Pdf Manuals
Related Search