Teasi Smart T Power Quick Start Guide
Contents
1. in place in the designated recess for safekeeping when not in use as otherwise the adapter port will not be protected against water and dust If an appropriate adapter see illustration is plugged into the port 5 correctly this connection is waterproof and dustproof Do not change or plug in the adapter in the rain or for example on the beach as water sand or dirt could get inside If water or sand dust penetrates inside this can lead to short circuits or mechanical damage These are not covered by the warranty WARNING Never use any other adapter even if they fit the port The polarity and wiring may be different and this would result in the likely destruction of the connected device and or the smarT power i Image of a TEASI connected to smarT power This is an example of what a correctly connected micro USB Jij adapter looks like The adapter must be fully inserted Technical specifications Input DC 5V 1A direct current maximal permitted 6 5V 1A direct current Output DC 5V 1A direct current The charging current is regulated according to the device connected Built in battery 5400mAh Li polymer rechargeable battery Maximum efficiency 90 depending on the system up to approx 90 of the maximum capacity can be extracted Luminosity of the high power LED Cool white max 300 lume2. may become less bright as a result This is normal The foldout angle must not exceed 90 and the spotlight should never be turned in the other direction Built into the back of the light is a metal component for cooling the LED This can get very warm or even hot depending on the length of time in use and the light intensity This is also normal Avoid contact with this component Connecting to a HR 4QF system mount ef gs Push smarT power onto the 4QF mount from above until smarT power snaps securely into place You can attach your smartphone or TEASI case on the other side in the same manner Make sure that both locking mechanisms have snapped into place securely on both sides smarT power is thus mounted between the mount and the mounting case of the smartphone TEAS almost like the filling in a sandwich Connecting the adapters supplied The following 4 charging adapters for receiver devices are supplied with smarT power ira 1 Micro USB 2 Mini USB SJ 3 iPhone 4 4s 4 iPhone 5 gt These allow you to charge or recharge almost all mobile devices on the market j navigation devices mobile phones tablet f PCs MP3 players etc 1 2 3 4 Each of these 4 adapters can be plugged into the green port for external devices 5 Care fully pull the appropriate adapter out of its holder The green port 5 for receiver devices should be inserted and secured
3. SMAR Quick start guide Intended use smarT power is a universal charging device for charging in absence of other charging options your mobile phone your TEASI navigation system or other devices with a 5V USB charging capability while you are out and about Depending on the battery capacity of the device to be charged it may even be possible to charge or recharge it several times smarT power is also equipped with a high power LED spotlight as well as mechanical connectors for the universal HR 4 Quick Fix System shortened to 4QF below which is the most widely used system in the mobile and outdoor sector and therefore offers you the most universal connection options This means that smarT power can be securely attached onto your bicycle handlebars with the same bike mount system as TEASI The other side of the mount can then hold your TEASI or your mobile phone case The road in front of you is well lit by the powerful spotlight 8 5 smarT power is dustproof and waterproof in accordance with standard IP65 which means that smarT power can be used outdoors even in heavy rain for example Please follow the instructions on this subject later in this guide Connecting and control elements 6 3 4 4 7 2 A 2 3 4 5 6 7 8 LED spotlight Connector for HR 4QF mount Switch for LED spotlight ON OFF switch for charging function Adapter port for external devices Battery status indicator HR 4QF mount for external
4. devices aa a a a a anaana a Se YS FS FS FS Fe LYS aS Charging input with rubber cap Below we simply refer to external devices that are to be charged as receivers as they receive the charging voltage and current from the donor smarT power Basic operation 4 Charging the receiver e g smartphone or TEASI Press the ON OFF switch 4 1x smarT power starts to charge the receiver Pressing the ON OFF switch 4 again stops the charging process 3 Spotlight functions Press 1x switches on LED spotlight while light full power Press 2x white LED approx half strength Press 3x red light Press 4x switches off LED spotlight If the switch 3 is not pressed again within 5 seconds to change to the next LED mode the next time the switch 3 is pressed all LED functions are switched off immediately 6 Battery status indicator This three colour LED indicator shows the status using 3 colours red yellow and green 1 smarT power is operational i e smarT power is operating as a donor A receiver is being charged or the LED spot light is switched on Rapidly flickering red light less than 5 charge remaining WARNING Please switch off the smarT power device immediately to prevent a deep discharge of the built in battery Note Even a single deep discharge could permanently damage the built in lithium bat tery This type of damage is not covered by the warranty Continuous red light 16 30 resid
5. mmersed or submerged in water Warranty service You the consumer receive a 36 month warranty commencing on the date of purchase This warranty does not apply to damage caused by improper treatment or external influ ences water dropping sun impact or breakage The full warranty conditions are available at www teasi eu If you have any technical queries and or problems please contact us by phone on 49 0 511 123 83 506 or via email to support first servicecenter de
6. ns USA CREE XPG series LED Beam angle 15 Dimensions 120mm x 66mm x 17 mm Weight 165g without adapter Operating temperature 20 C to 60 ambient temperature Note The optimum ambient temperature of lithium batteries is approx 20 C 45 C At temperatures below approx 10 C the operating time of lithium batteries can decrease significantly This is normal and does not constitute a defect or fault Included in the delivery 1 x smarT power 1 x charging cable with USB connector 1 x charging cable with open ends e g for connecting to a hub dynamo red black 1 x iPhone 4 4S adapter 1 x iPhone 5 5S adapter 1 x micro USB adapter with 90 connector 1 x mini USB adapter 1 x waterproof storage bag for the adapter 1 x this guide Final notes safety information 1 To prevent the built in lithium battery from discharging we strongly recommend charging smarT power approx once every 3 months to avoid a complete or even deep discharge of the lithium battery Deep discharges will destroy the built in lithium battery 2 smarT power must be disposed of in accordance with statutory requirements and legislation Do not discard it in the countryside or in normal household waste 3 This device smarT power must never be heated or exposed to naked flames 4 In the event of mechanical damage or breakage of the casing the device must be sent to the manufacturer for inspection 5 This device smarT power must never be i
7. ual charge smarT power should be recharged soon Continuous orange light 31 50 residual charge Continuous green light 51 100 residual charge 2 The internal battery of smarT power is being charged Flashing red 1 30 charged smarT power is charging Flashing orange 31 50 charged smarT power is charging Flashing green 51 99 charged smarT power is charging Continuous green light smarT power is fully charged The charging process can be stopped To recharge smarT power use a standard USB charger with a 5V 1A charging port e g from a smartphone and the USB charging cable supplied The cable is plugged into the charging input 8 under the rubber cap A charge cycle takes about 6 hours if the re chargeable battery is almost or completely empty Waterproof and dustproof in accordance with IP65 What does this mean You can use smarT power even in heavy rain and off road smarT power is appropriately waterproof and dustproof for these conditions However the following requirements must be observed smarT power must never be immersed or submerged in water If this happens for example as the result of a fall immediately switch off smarT power completely wipe dry all ports and blow water out of them Then please send the device to the service center as soon as possible If you do this please indicate that your smarT power has fallen into water Never open the device yourself Lithium batteries are subject to special safet
8. y re gulations To clean the device it is best to use a soft cloth which should be lightly damp at most Never use water or a damp cloth to clean the electrical ports 5 and 8 Do not recharge smarT power or connect it to an external power source in the rain as the charging socket is only waterproof when the rubber cover is securely closed The adapter port 5 for receiver devices should be stored in the designated recess for safekeeping when not in use Otherwise the port itself is not protected against water and dust If an appropriate adapter see below e g mini USB for TEASI is plugged into the port 5 and the adapter has been inserted correctly this connection is waterproof and dust proof However you should never change or plug in the adapter in the rain or for example on the beach in the wind If water or sand dust penetrates inside this can lead to short circuits or mechanical damage These are not covered by the warranty LED spotlight 1 smarT power bis equipped with a powerful USA CREE LED spotlight with a correspon dingly long service life of approx 5 000 hours The LED spotlight can be folded out up to an angle of 90 A mechanical lock prevents an angle of more than 90 If it is difficult to rotate you should never attempt to turn it by force You may have already reached the end stop or there may be something blocking the pivot Caution i The built in battery is discharged during use The LED light
Download Pdf Manuals
Related Search