Targus USB-2.0 Mobile User's Manual
Contents
1. Each USB light glows blue when a device is connected to the port Specifications Dimensions 2 inches diameter Weight 2 5 ounces 70 9 g Operating Temperature 32 to 158 degrees Fahrenheit 0 to 70 degree Celsius Standards USB Specification Revision 2 0 and 1 1 compatibility Data Speed USB v1 1 12 Mbps USB v2 0 480 Mbps Connector Ports Hub to computer 1 series B receptacle Hub to devices 4 series A receptacle LED Indicators Power 1 Red Hub to devices 4 White blue Per Port Current 500 mA with the AC power adapter External Power AC Power Adapter DC 5 Volt Cable length 6 foot 1 83 m Troubleshooting General Can I connect USB 1 1 compatible devices to the mini hub Yes the mini hub is backward compatible with USB 1 1 devices Can I use the mini hub without the AC power adapter No you must use the supplied AC power adapter to ensure that the devices work properly Device Not Working Make sure that the device is firmly connected to the port on the mini hub Plug the device into a different port on the mini hub Ifit still doesn t work test the device by connecting it directly to your computer Check that you ran the Setup or Install program for the device Make sure that the device appears in Device Manager See Verifying Device is Installed below Disconnect all devices from the mini hub and reconnect them one at a time Check that each device works before2. plugging in the next one Verifying Device is Installed Windows Operating System To check that the mini hub is installed properly use Device Manager to locate the Generic USB Hub on USB 2 0 Bus device To access Device Manager for the Windows 98 Me operating system right click My Computer Properties and then click the Device Manager tab For the Windows 2000 XP operating system right click My Computer Properties click the Hardware tab then click the Device Manager button To test that the mini hub is working properly in the Device Manager window Select the Generic USB Hub on USB 2 0 Bus device 2 Click the Properties button or icon depending on your operating system 3 Verify that the message This device is working properly appears b Macintosh Operating System To verify that the mini hub is installed properly locate the Generic USB Hub on USB 2 0 Bus device by opening Apple System Profiler and clicking Devices and Volumes USB Hub Current Limit Exceeded Warning If a device exceeds the power available for its hub port the following screen appears with the offending device highlighted USB Hub Current Limit Exceeded The USB Human Interface Device has exceeded the current limits of its hub port The placement of the device is highlighted in bold type USB Root Hub 2 ports Unused Port E Generic USB Hub 4 ports a USB Human Interface Device a HID compliant mouse Unus
3. TARGUS NOTEWORTHY TARGUS NOTEWORTHY Essential Accessories for Mobile Computing Making Your Mobile Life Easier USER S GUIDE Visit our Web site at www targus com Making Your Mobile Life Easier Features and specifications are subject to change without notice 2002 Targus Corp 400 0093 001A BrRusseLs HAannoveR BAaRceLona Tokyo MIiLaNno AMSTERDAM SINGAPORE LonDpon PaRi s NewYork Los AnGceLes Toronto Honc Kone SYDNEY PMS Black 15 PMS Black 100 USB 2 0 Mobile Mini Hub Introduction Congratulations on your purchase of the Targus Noteworthy USB 2 0 Mobile Mini Hub This ultra portable mini hub is USB 2 0 compliant and connects to a Universal Serial Bus USB port on your desktop or notebook computer The mini hub has four ports for connecting USB high speed 2 0 or standard 1 1 devices to your computer One or more of these devices can be additional hubs You can daisy chain up to 127 USB high speed 2 0 or standard 1 1 devices to your computer in this way The mini hub also provides a maximum bandwidth of 480 Mbps which enables you to connect devices that consume a large amount of bandwidth such as an external storage device printer scanner DVD or CD RW drive or digital camera to your computer In addition to this user s guide this package contains the USB 2 0 Mobile Mini Hub a high speed USB 2 0 cable and an AC power adapter and cord System Requirements To use the mi
4. ed Port Unused Port Recommendation Disconnect the device and then click Reset to re enable the port If you click Close a reboot will be required to regain the port USB Hub Current Limit Exceeded screen To re enable the hub port for the affected device follow the on screen instructions Technical Support In the unlikely event that you encounter a problem with your Targus accessory please contact our technical support team at Email Internet techsupport targus com http www targus com support asp Our knowledgeable staff is also available to answer your questions through one of the following telephone numbers US Monday through Friday 8 00 a m 08 00 to 8 00 p m 20 00 Eastern time Canada 800 283 6325 Monday through Friday 9 00 a m 09 00 to 5 00 p m 17 00 Eastern time Europe Belgium Denmark France Germany Italy Netherlands Spain Sweden Switzerland United Kingdom Eastern Europe amp others 888 827 4877 32 0 02 717 2451 45 0 35 25 8751 33 0 1 64 53 9151 49 0 21 16 579 1151 39 024 827 1151 31 053 484 9470 34 091 745 6221 46 0 8 751 4058 41 0 1 212 0007 44 0 20 7744 0330 31 053 484 9479 Product Registration For more efficient customer service and to activate the product s warranty Targus recommends that you register your Targus accessory shortly after purchasing it To register your Targus accessory go to http www targus com reg
5. ed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation 10 If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Move the computer away from the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Intel and Pentium are registered trademarks of Intel Corporation Windows is a registered trademark of Microsoft Corporation Macintosh is a registered trademark of Apple Computer Inc All other trademarks are the property of their respective owners 11
6. istration asp You will need to provide your full name email address phone number and company information if applicable Warranty Targus warrants this product to be free from defects in materials and workmanship for one year If your Targus accessory is found to be defective within that time we will promptly repair or replace it This warranty does not cover accidental damage wear and tear or consequential or incidental loss Under no conditions is Targus liable for loss of or damage to a computer nor loss of or damage to programs records or data nor any consequential or incidental damages even if Targus has been informed of their possibility This warranty does not affect your statutory rights Warranty Registration at http www targus com registration asp Regulatory Compliance This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation FCC Statement Tested to Comply This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not install
7. ni hub your computer must meet the following hardware requirements and run one of the operating systems listed below Hardware Operating System e PC with a 233 MHz or faster Intel e Windows 98SE Me Pentium processor or equivalent 2000 XP and a hard disk drive e 64 MB RAM or higher depending Mac OS X and higher on the operating system e USB version 2 0 interface N NOTES The USB 2 0 Mobile Mini Hub is backward compatible so you can connect it to a computer with either a version 1 1 or 2 0 USB interface When using the mini hub with a computer that has a version 1 1 USB interface all of the devices attached to the mini hub will run at a version 1 1 USB speed Connecting the Mini Hub to Your Computer and Installing the Default Device Drivers To connect the mini hub to your computer and install the operating system s default drivers 1 Plug the supplied high speed cable s USB connector end type A into a USB port on your computer 2 Plug the cable s other connector end type B into the mini hub AC power USB port jack type B Mini hub AC power jack and USB port type B 3 Connect the supplied AC power adapter to the AC power jack on the mini hub then plug the adapter into an available electrical outlet Your computer s operating system automatically detects the new hardware and begins installing the appropriate default drivers 4 Follow the on screen instructions to complete the driver in
8. stallation You can now connect USB devices to the mini hub or daisy chain additional hubs Connecting Devices to the Mini Hub To connect a USB device plug it into a USB port on the mini hub and follow any additional instructions provided with the device When connecting new devices to the mini hub consider the following guidelines If your computer is running the Windows 98 operating system a series of screens appear beginning with the Add New Hardware Wizard to guide you through the driver installation process If your computer is running the Windows Millennium Edition Windows 2000 or Windows XP operating system the device drivers may install automatically When connecting a new device to the mini hub you must run the Setup or Install program for that device When connecting a device to the mini hub to avoid possible damage never force the cable connector into the port on the mini hub If the cable connector does not attach smoothly remove the connector turn it over and try attaching it again LED Status Indicator Lights Once the default drivers are installed the LED status indicator lights glow and you can connect devices to the mini hub Mini hub LED status indicator lights The LED lights display as follows e Power light glows red when the mini hub is receiving power from an external power source NOTE Use only the supplied AC power adapter with the mini hub to avoid possible damage e
Download Pdf Manuals
Related Search