Tanaka TPH-200 User's Manual
Contents
1. improper use of the unit may cause serious or fatal injuries This pole trimmer attachment has been designed for certain TANAKA brush cutters NOTE Do not use this attachment on the brush cutters with over 26 ml cc engines SAFE OPERATION WARNING 4 DANGER All overhead electrical conductors and communications wires can have electricity flow with high voltages Never touch wires directly or indirectly when pruning otherwise serious injury or death may result CAUTION e Always wear gloves during operation or maintenance e Review the area to be trimmed Look for hazards that could contribute to unsafe conditions DO NOT operate unit if any wires power telephone cable etc are closer than 15M 50ft to any part of the operator or unit Fig 1 1 e Spectator and fellow workers must be warned and children and animals prevented e from coming nearer than 15M 50ft while the pole trimmer is in use Fig 1 2 e Avoid all power lines This unit is not insulated against electrical current e Always wear head protection with full face shield to help protect against falling branches and debris Fig 1 2 www tanakapowerequipment com 2 custsvc tanaka ism com lanaka _ TH200_ _____ Owner s Manual 2 Assembly procedures Installation of cutting attachment Fig 2 1 1 Remove gear case from your brush cutter 2 Join the attachment in place of it NOTE If your brush cutter tube is 26mm diam2. eter remove bracket collar B 4 from the attachment 3 Make sure the locking bolt 1 fits in the location hole 2 of tube and that the tube will not come off 4 Tighten the clamp bolt 3 securely Fig 2 1 1S WARNING During operation hold the unit firmly with both hands A single hand operation may cause serious injury Adjustment of blade angle Fig 2 2 3 LIN WARNING Always stop engine before making adjustments Never touch the blade when adjusting blade angle Hold the support handle 3 instead 1 Stop the engine 2 Loosen wing nut 1 and knob nut 2 slightly so that the support handle 3 slides 3 Adjust the blade angle to desired position by holding the support handle 3 4 Then finger tighten the knob nut 2 securely and also the wing nut 1 Fig 2 3 www tanakapowerequipment com 3 custsvc tanaka ism com lanaka _ TH200_ _____ Owner s Manual 3 Trimming techniques e This attachment is designed for trimming hedges and small branches Follow these tips for successful operation e Plan cut carefully Check direction branch will fall e Long branches should be trimmed in several pieces e Do not stand directly beneath branch being cut e Apply a light cutting pressure e Ease cutting pressure when nearing end of cut to maintain control 4 Maintenance Gear case Fig 4 1 Apply a good quality lithium based grease through the grease fittings NOTE Lubricat
3. ion should be applied at 50 hour intervals and more frequent at heavy use Fig 4 1 Cutter blade Fig 4 2 3 The blades are installed to the cutter guide with three to five bolts depending on cutter length Those bolts are tightened with a clearance so that the cutters can move smoothly When clearance is too small The cutters do not move properly and the sliding surfaces may seize When clearance is too large The cutters are poor in sharpness To adjust the cutter clearance 1 Loosen the cutter fixing nuts 2 Fully tighten the cutter fixing bolts and then loosen them approx 1 2 turn 3 With the bolts set at that position tighten the cutter fixing nuts Be sure to replace cutter guide fixing bolts when they are loosened worn or damaged Also be sure to replace damaged cutter blade NOTE Properly lubricate the cutter sliding surfaces with machine oil www tanakapowerequipment com 4 custsvc tanaka ism com lanaka _ H200 Seer Manual Specifications En MODEL TPH 200 Dry Weight kg E E cave awh Ces baawk 550 MM sses 1 9 4 1 Ibs Overall cutter length mm eere 550 21 65 in X All data subject to change without notice www tanakapowerequipment com 5 custsvc tanaka ism com
4. lanak Owner s Manual Model Numbers PIN 30350 TP H 200 Date 05 21 01 POLE HEDGETRIMMER ATTACHMENT TPH 200 Supplier To The Outdoor Power Equipment Industry ISM Inc 1028 4 Street SW Auburn WA 98001 Phone 253 333 1200 Fax 253 333 1212 www tanakapowerequipment com custsvc tanaka ism com lanaka _ THh200_ _____ Owner s Manual Before using this unit Read the operator s manual carefully Check that the cutting equipment is correctly assembled and adjusted Start the unit and check the carburetor adjustment See Maintenance WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer birth defects and other reproductive harm Read understand and follow all warnings and instructions in this It is important that you read fully understand manual and on the unit and observe the following safety precautions and warnings Careless or improper use of the unit may cause serious or fatal injury Always wear eye head and ear Do not touch the blade when l protectors when using this unit running the engine www tanakapowerequipment com 1 custsvc tanaka ism com lanaka _ H200 Seer Manual 1 Introduction It is important that you read and understand your TANAKA brush cutter owner s manual as well as this manual Please carefully review and observe all safety precautions and warnings Careless or
Download Pdf Manuals
Related Search