Swisher LS12534H User's Manual
Contents
1. Move choke to CHOKE position Prime engine Turn on fuel valve or clean fuel line Clean adjust gap or replace spark plug Connect and tighten spark plug wire Move choke lever to OFF position Clean fuel line fill tank with clean fresh gasoline Drain fuel tank Refill with fresh gasoline Clean or replace air cleaner See authorized service center Engage cold weather clutch Replace or reinstall belt Fill hydraulic tank to correct fluid level Flush and clean hydrualic system See authorized service center See authorized service center Fill hydraulic tank to correct fluid level Drain fluid flush system and refill Make certain pump hoses are clear and unblocked Make certain hose in not collapsing under suction See authorized service center See authorized service center See authorized service center TROUBLESHOOTING CONTINUED Problem Leaking Cylinder 1 Broken seals 1 See authorized service center 2 Scored cylinder 2 See authorized service center TT 12 Volt Units eae een eet Engine will not turn over Weak or dead battery Recharge or replace battery Blown fuse Replace fuse Corroded battery terminals Clean battery terminals Loose or damaged wiring Check all wiring Faulty ignition switch Check replace ignition switch Faulty solenoid Check replace solenoid Engine clicks but will not start Weak or dead batte2. e ALWAYS wear protective gear such as safety goggles protective hearing device steel toed shoes and tight fitting gloves without drawstrings or loose cuffs e NEVER wear loose clothing or jewelry that can be caught by moving parts of the splitter and pull you into it Keep hair away from moving parts e NEVER operate your splitter on wet muddy or icy surfaces KEEP work area clean of split wood Safe footing is essential in preventing accidents e ONLY operate splitter on level ground with wheels blocked not on the side of a hill It could tip or rolling logs poor footing etc could cause an accident 3 NEVER operate your splitter near a flame or spark Hydraulic oil and gasoline are flammable and can explode NEVER fill gas tank while the engine is hot or running Allow the engine to cool before refueling This unit is equipped vvith an internal combustion engine and should not be used on or near any unimproved forest covered brush covered or grass covered land unless the engine s exhaust system is equipped with a spark arrester meeting applicable local or state laws if any If a spark arrester is used it should be maintained in effective working order by the operator NOTE In the state of California the above is required by law Section 442 of the California Public Resources Code Other states may have similar laws Federal laws apply on federal lands A spark arrester muffler optional by manufacturer is available
3. 1 800 222 8183 The model number serial number date of purchase and the name of the authorized Swisher dealer from whom you purchased the splitter will be needed before any warranty claim can be processed THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES Some states do not allow the limitation of consequential damages or limitations on how long an implied warranty may last so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may have other rights All engines utilized on our products have a separate warranty extended to them by the individual engine manufacturer Any engine service difficulty is the responsibility of the engine manufacturer and in no way is Swisher Mower Co Inc or its agents responsible for the engine warranty The Briggs amp Stratton Engine Service Hot Line is 1 800 233 3723 The Tecumseh Engine Service Hot Line is 1 800 558 5402 The warranty period for any product used for commercial or rental is limited to ninety 90 days from the date of original purchase This warranty applies only to products which have been properly assembled adjusted and operated in accordance with the instructions contained within this manual This warranty does not apply to any product of Swisher Mower Co Inc that has been subject to alteration misus
4. Link For Idler Arm BRS6H 28 Idler Tension Spring Bent Leg 4422 29 Bolt Spade 5 16 18 X 12 10636 Nut 5 16 18 Nyloc NB181 Return Hose 72 12363 32 16 Hose Clamp LS4999 Not Shown Grommet 12441 Not Shown 44 Belt 644 PUMP DET AIL Pressure oN ALL MODELS ITEM DESCRIPTION PART Hydraulic Pump Model LS722H amp LS728H 12360 Hydraulic Pump Model LS10528H LS12534H amp LS12534H12V LS2002B 16 Hose Clamp LS4999 pa Bolt 5 16 18 X 3 4 Serr Flange NB596 Pr Pa Nut 5 16 18 Serr Flange NB170 of pulley flush with end of pump shaft Note Install pulley collar up and bottom side 11 Beam Weldment 12399TC Shown BEAM DETAIL ALL MODELS NOT ALL PARTS ARE ON ALL MODELS TEM NUMBER 172 13 Nut o SSCS STGP e 12 Master Chain Link SEE BEAM LOCKING PIN DE TAIL TONGUE DETAIL ALL MODELS DESCRIPTION 13 ENGINE DETAIL MODEL LS10528H amp LS12534H NA Nut 5 16 18 Serr Flange NB170 Upper Spacer 689S Engine Pulley BB105 Washer Ballevile OJ 69 TJ ENGINE DETAIL MODEL LS722H amp LS728H Z6 3 a 688 TJ Note Install pulley collar up and bottom side NOTSHOWN Fuel Shut Off Valve Inline 7414 of pulley flush with end of engine shaft NOTSHOWN Fuel Line Clamp 6FLC 14 12 Volt Accessories BATTERY Throttle Cable 686N Bolt 3 8 16 X7 8 Bolt 5 16 18 X 3 4 NB143 NOTSHOWN Nut 5 16 18 Serr Flange 9 Bolt 174 20 Se
5. MODEL NUMBER TYPE PART NUMBER PART DESCRIPTION www swisherinc com TELEPHONE 1 800 222 8183 FAX 1 660 747 8650 SWISHER MOWER amp MACHINE CO INC 1602 CORPORATE DRIVE WARRENSBURG MO 64093 SWISHER MOWER amp MACHINE CO INC
6. Uy pss SAFETY DECALS Replace decals immediately if damaged COLD WEATHER CLUTCH Shut off fuel for transport dt PUSH ODOT j Failure to do so may cause unit to I flood y PULL OD16 FUEL SHUT OFF DECAL 12493 COLD WEATHER DECAL HYDRAULIC FILL PLUG Maintain hynie Sh hae in safe opeating range Be N ot Exceed tween d Use a Universal hydrauli K fuid or Denton M Tirenisi n fluid pr 45 MPH 12549 J 12494 HYDRAULIC FILL PLUG 12549 DO NOT EXCEED 45 MPH DECAL DECAL NOTICE ADD HYDRAULIC OIL BEFORE OPERATING THIS EQUIPMENT __ 12532 HYDRAULIC OIL DECAL VERTICAL OPERATOR S INSTRUCTIONS READ OPERATOR S MANUAL bent yl laa E 3 Set the engine throttle at maximum speed Xi 4 Place the log against the end plate End Veo 5 Stabilize the log when needed on its side NEVER Plate p e li k LA Only one adult should stabilize the log and operate IS on the end between the log and the splitting wedge 9 the control 4 ES 7 Move the control handle in the splitting direction La a 8 Release the control handle to stop the wedge OR SA movement ba I f 9 Move the control handle opposite the splitting M direction to return the wedge HORIZONTAL w a 12492 OPERATOR INSTRUCTION DECAL A DANGER AVOID SERIOUS INJURY OR DEATH READ AND UNDERSTAND OPERATOR S MANUAL BEFORE USING e Always operate outdoors with adequate ve
7. at your nearest engine dealer Check legal requirements in your area ONLY use your hands to operate the control lever NEVER use foot knee rope or any extension device Split ONLY one log at a time NEVER attempt to split two logs on top of each other NEVER place hands or feet between log and splitting wedge or between log and ram during forward or reverse stroke ALWAYS keep fingers clear of splits that open in log during splitting operation DO NOT straddle or reach across the splitting area while operating the splitter DO NOT step over splitter when the engine is running You may trip or accidentally activate the splitting wedge Walk around to get to the other side NEVER attempt to load splitter while splitting wedge is in motion When loading log splitter place hands on the sides of the log not the ends NEVER attempt to split woods across the grain Wood may burst or fly out of your splitter and result in serious injury NEVER leave your splitter unattended with the engine running Shut off the engine if you are leaving your splitter even for a short period of time Someone could accidentally activate the ram and be injured Both ends of the log should be cut as squarely as possible to prevent the log from sliding out of the splitter during operation Log length should be kept to 24 or less NEVER operate your splitter while it is attached to the tow vehicle BEFORE towing be certain that the splitter is securely attach
8. stop engine move throttle lever to SLOW for a few seconds then to STOP COLD WEATHER START UP The Cold Weather Clutch enables the engine to be started without having to pull through cold thickened hydraulic fluid Simply pull the handle out into locked position Start engine let it warm up and release Cold Weather Clutch After starting assure that the lever has reengaged SPLITTER OPERATION 1 Set up the log splitter in a clear level area and block the wheels The suction port on the tank should always be on the lower side of the log splitter 2 Place a log on the beam against the foot plate Make sure the log is securely on the foot plate and up against the beam 3 Depress the valve lever so that the cylinder will drive the push block into the log Extend the cylinder until the log splits or to the end of its stroke If the log has not completely split after the cylinder has reached the end of its extension retract the cylinder NOTE Leaving the valve in the actuate position at the end of the stroke may damage the pump Always use extra care when splitting logs with ends that are not square NOTE To extend the life of the hydraulic cylinder avoid BOTTOMING OUT the cylinder TOWING SAFETY This unit should not be towed on any street highway or public road without checking the existing federal local and state laws Any licensing or modifications such as taillights etc need to comply with existing feder
9. al local or state vehicle requirements is the sole responsibility of the purchaser Obey all regulations when towing on public roads and highways See also SAFETY PERCAUTIONS Turn the fuel shut off valve if applicable OFF to prevent flooding of the engine while traveling Be careful when backing up You can easily jack knife your splitter TOWING AT NIGHT The requirements for taillights are based on States regulations Some states allow towing at night as long as the towed equipment does not visibly impair the tow vehicle taillights This is based on a state to state requirements The customer is responsible for meeting the states requirements If a Statement of Origin is required in your state see your local dealer to receive one HYDRAULIC SAFETY The hydraulic system on your splitter requires careful inspection along with the mechanical parts Be sure to replace any frayed kinked cracked or otherwise damaged hydraulic components Just because it isn t leaking today doesn t mean that it will not fail tomorrow Fluid escaping from a very small hole can almost be invisible Do not check for leaks with your hand Escaping fluid under pressure can have sufficient force to penetrate skin causing serious personal injury or even death Leaks can be detected by passing a piece of cardboard or wood over the suspected leak and looking for discoloration IF injured by escaping fluid see a doctor at once Serious infection or reaction can d
10. e abuse improper assembly or installation shipping damage or to normal wear of product Excluded from this warranty are normal wear normal adjustments and normal maintenance The pump valve and cylinder each carry separate manufacture s warranties The valve and cylinder both carry a one 1 year limited warranty The pump carries a two 2 year limited warranty which vary from state to state This is a limited warranty as defined by the Magnuson Moss Act of 1975 WARRANTY SAFETY TOWING OPERATION TABLE OF CONTENTS MAINTENANCE DECALS PARTS BREAKDOWN SPECIFICATIONS SAFETY PRECAUTIONS This Safety Alert Symbol indicates important messages in this manual When you see this symbol carefully read the message that follows and be alert to the possibility of personal injury Pe Read this manual completely This machine can amputate hands feet and throw objects Failure to observe the following safety instructions could result in serious injury or death WARNING The engine exhaust from this product contains chemicals known to the state of California to cause cancer birth defects or other reproductive harm DANGER Your log splitter was built to be operated according to the rules for safe operation in this manual As with any type of power equipment carelessness or error on the part of the operator can result in serious injury If you violate any of these rules you may cause serious injury to yourself or oth
11. ed to the towing vehicle and that the support leg beam and cylinder are secured in there respective towing positions NEVER allow persons to ride on splitter DO NOT carry any cargo or wood on your splitter It may fall off and cause an accident DO NOT loosen or remove any hydraulic fitting line or reservoir cap while your splitter or engine is running Fluid escaping from a very small hole can almost be invisible DO NOT check for leaks with your hand See maintenance section for instructions IF injured by escaping fluid see a doctor at once Serious infection or reaction can develop if proper medical treatment is not administered immediately DO NOT operate your splitter in poor mechanical condition or when it is need of repair ALWAYS disconnect the spark plug wire and place the wire where it cannot contact the spark plug to prevent accidental starting the engine when setting up transporting adjusting or repairing 4 TOVVING SAFETY e Do not allow persons to ride on splitter Do not carry any cargo or wood on your splitter It may fall off and endanger vehicles that are following you e Be sure support leg is in the travel position and coupling secure This must also be retracted so not to interfere while towing Retract support leg by removing pin pivoting up and replacing pin e Never exceed 45 MPH while towing your splitter Be extra cautious when traveling over rough terrain especially over railroad tracks e Alway
12. ers e Read and understand the manual Learn to operate this equipment in a safe manner Familiarize yourself with all of the controls in a safe environment before starting to work with this machine e DO NOT under any circumstances alter this log splitter This equipment was designed and engineered in accordance with operating instructions Altering this equipment or using this equipment in such a way as to circumvent its design capabilities and capacities could result in serious injury or fatality and WILL VOID THE WARRANTY e Allow ONLY responsible adults who have read this manual to operate this machine NEVER allow children to operate this machine e NEVER operate or allow someone to operate this equipment while under the influence of alcohol drugs or medication Being coherent is essential for safety e ALWAYS use outdoors with adequate ventilation DON T run the engine in an enclosed area Exhaust gases contain carbon monoxide This odorless gas can be deadly when inhaled e NEVER use splitter for any other purpose than splitting wood Any other use can result in injury Your splitter is a precision piece of power equipment not a toy Therefore exercise extreme caution at all times e ONLY a single operator is to load and operate the log splitter KEEP all others including pets and children a minimum of 20 feet away from your work area More accidents occur when more than one person operates the log splitter than any other time
13. esigned to give us all more relaxing in the shade time Swisher products have been featured nationally on television programs such as Regis and Kathie Lee and seen in publications like ATV Magazine Country Journal Popular Mechanics Magazine and others In January 2000 Popular Mechanics Magazine named Max s zero turning radius riding mower one of the 20 century s top household inventions Swisher offers value and function in its products tg meet your grounds maintenance peed CELEBRATING 60 YEARS OF INNOVATION gt MADE IN THE U S A 0D39 18 A TRADITION OF QUALITY SINCE 1945 OWNER S MANUAL MODEL NO LS722H LS728H LS10528H LS12534H LS12534H12V LOG SPLITTER HOW TO ORDER REPAIR PARTS Each Log Splitter has its own serial number Each engine has its own serial number The serial number for the Log Splitter will be found on the right hand side of the hydraulic oil reservoir The serial number for the engine will be found on the top of the blower fan housing All Log Splitter parts listed herein may be ordered directly from Swisher Mower amp Machine Co Inc your nearest Swisher dealer or from our website All engine parts may be ordered from the nearest dealer of the engine supplied with your log splitter Parts subject to change without notice WHEN ORDERING PARTS PLEASE HAVE THE FOLLOWING INFORMATION AVAILABLE PRODUCT SWISHER LOG SPLITTER SERIAL NUMBER MODEL NUMBER ENGINE
14. evelop if proper medical treatment is not administered immediately Should it become necessary to loosen or remove any hydraulic fittings lines or reservoir cap be sure to relieve all pressure by shutting of the engine and moving the control handle back and forth several times NEVER remove the cap from the hydraulic tank or reservoir while the unit is running Hot oil under pressure could result in serious injury See also SAFETY PERCAUTIONS The pressure relief valve on your splitter is preset at the factory DO NOT adjust the valve Only a qualified technician should perform this adjustment MAINTENANCE AND STORAGE WARNING DISCONNECT THE SPARK PLUG BEFORE PERFORMING ANY MAINTENANCE Consult the operating and maintenance instructions of the engine manufacturer for engine care Always check the oil level of the hydraulic reservoir before operation Operating without an adequate oil supply will cause severe damage to the pump Change the hydraulic fluid in the reservoir after every 100 hours of operation Change the hydraulic filter after every 50 hours of operation use only a 10 micron hydraulic filter Periodically check that all nuts bolts screws clamps and fittings are tight and secure To keep your splitter in top working condition perform all recommended maintenance procedures before you use your splitter If the wedge becomes dull or nicked a grinder or sharpening tool can be used to sharpen it Completely drain the fuel
15. gs and part lists should it become necessary to disassemble the unit for repair or replacement of parts Inspect all components for damage If you believe you have a damaged part please contact customer service immediately at 1 800 222 8183 WARNING Exercise extreme caution as parts are very heavy Sufficient persons or mechanical handling equipment should be used Refer to uncrating and assembly instructions for assembly procedures OPERATION INTENDED USE This log splitter is intended and designed to only split wood NEVER use for any other purposes Doing so can cause injury or VOID THE WARRANTY IMPORTANT This unit is shipped with oil but without gasoline in the engine After assembly see separate Engine Manual for proper fuel and oil recommendations WARNING DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE ENGINE AND HYDRAULIC RESERVOIR FILLING THE HYDRAULIC RESERVOIR Fill the hydraulic reservoir to the top mark on the dipstick with Dexron III Mercon III automatic transmission fluid a 10YV AW hydraulic fluid or Pro Mix AW 32 Hydraulic oil After the hydraulic reservoir and the engine crankcase are filled correctly with their respective oils start the engine Remember to set the throttle and turn on the fuel shut off valve The hydraulic pump should prime itself With the engine running move the hydraulic valve lever toward the wedge This will cause the cylinder to extend and expel air When the cylinder is ful
16. ly extended retract it Repeat this procedure several times An erratic movement of the cylinder and wedge indicates that there is air in the system Once the cylinder has a smooth and constant speed indicating that all air has been expelled shut the system off and refill the reservoir until the fluid is in the safe operating range as specified by the marks on the dipstick START UP WARNING DO NOT START OR RUN THE LOG SPLITTER WITHOUT OIL IN THE ENGINE AND HYDRAULIC RESERVOIR See separate Engine Manual for fuel and oil recommendations If applicable your log splitter has come equipped with a fuel shut off valve for towing purposes Before starting engine make sure crankcase is filled correctly with oil and the proper fuel has been used The engine will only start when the throttle lever and fuel shut off valve if applicable are turned to their ON positions STARTING INSTRUCTIONS 1 Move throttle control to FAST 2 Set Choke to on position if applicable or push primer bulb three 3 times NOTE Do not use primer or choke to restart a warm engine after a short shutdown 3 Grasp rope handle and pull out slowly until resistance it felt Then pull rapidly with a full arm stroke NOTE If engine fails to start after three 3 pulls repeat steps 1 and 2 4 When Engine starts set choke to off position if applicable leave throttle control at FAST The throttle must be set in the fast position for maximum performance 5 To
17. ntilation e Operate the log splitter in a locked position on a dry level surface with wheels blocked Safe footing is essential e Wear protective work gloves safety shoes and safety goggles Keep hands feet and loose clothing away from wedge end plate partly split wood and moving parts Position log on splitter with hands on its side not ends Only one operator permitted Adult who loads and positions log must be the one who operates control handle Keep bystanders helpers and children at least 20 feet away High pressure fluid can escape through a pin hole leak and cause serious injury by puncturing the skin and causing blood poisoning Never check for leaks with your hands Never operate under the influence of alcohol or drugs Do not refuel a hot or running engine e Never leave splitter running unattended even for a short time 11427 DANGER DECAL 9 SEE BEAM DETAIL SEE ENGINE DETAIL SEE PUMP DETAIL SEE TONGUE DETAIL ASSEMBLY DETAIL LS7522H LS728H LS10528H amp LS12534B MODELS 10 SERVICE PARTS Please have Model and Serial Numbers ready when ordering parts Color cannot be guaranteed upon service parts ITEM NUMBER DESCRIPTION PART NUMBER Siti2 LST 7329 Breather Cap 12379 2203B Tire amp Wheel 7296 2203CN NB633 2203DC 7289 NB107 NB272 6087 6040 NB182 Bolt 3 8 16 X2 1 2 GR 5 NB619 B527 NB280 Clutch Lever 11226TK 26 Clutch Lever Cap 2077 27 Wire
18. rr Flange NOTSHOWN Nut 1 4 20 Serr Flange NB524 10 Key Switch 3623 NOTSHOWN Wiring Harness 12551 NOTSHOWN Solenoid Assembly 10806 NOTSHOWN Nut M6 1 0 NB600 BATTERY IGHITION SWITCH Wiring Diagram Pump Pulley Engine fails to start Engine is hard to start or runs erratic Cylinder rod vvill not extend or contract Cylinder rod is slow or erratic while extending and contracting Idler Pulley Engine Pulley Cy BELT ROUTING DIAGRAM VIEWED FROM UNDERSIDE OF SPLITTER TROUBLESHOOTING Spark plug wire disconnected Fuel tank not full enough or stale fuel Throttle control lever not in correct starting position Choke not in CHOKE position Engine not primed properly Fuel valve not ON or blocked fuel line Faulty spark plug Spark plug wire loose 2 Unit running on CHOKE Blocked fuel line or stale fuel Water or dirt in fuel system Dirty air cleaner Carburetor out of adjustment Cold weather clutch not engaged Broken or improperly installed belt Low hydraulic fluid Hydraulic lines blocked Damaged or broken pump Damaged control valve Low hydraulic fluid Contaminated hydraulic fluid Excessive pump inlet vacuum Damaged pump Damaged control valve Internal cylinder damage 16 Connect wire to spark plug Fill tank full with clean fresh gasoline Move throttle lever to FAST position
19. ry Recharge or replace battery Corroded battery terminals Clean battery terminals Loose or damaged wiring Check all wiring Faulty solenoid Check replace solenoid Battery will not charge Bad battery Replace battery Corroded battery terminals Clean battery terminals Faulty solenoid Check replace solenoid Bad alternator See authorized service center NOTE For repairs beyond those listed here contact your nearest authorized service center Flushing the reservoir tank and hoses with kerosene whenever service is performed on the tank hydraulic pump or valve is recommended Contact an authorized service center MAINTENANCE LOG Date of Service Service Performed 17 SPECIFICATIONS Models LS722H LS728H LS10528H LS12534H amp LS12534H12V Splitting Force 22 Tons 28 Tons 28 Tons 34 Tons 6 5 HP Briggs and 7 HP Briggs and Stratton Stratton Quantum INTEK 10 5 HP Briggs and Stratton I C 12 5 HP Briggs and Stratton VC 12 volt Start Engine Splitting Positions Horizontal and Vertical Horizontal and Vertical Horizontal and Vertical Horizontal and Vertical Cylinder Size 4 X24 N 4 1 2 X24 i 4 1 2 X24 2 Stage with Heavy Duty 2 Stage with Heavy Duty 2 Stage with Heaw Duty Bearings Bearings Bearings 5 X24 Pump 2 Stage with Heaw Duty Bearings Pump Specs 11 Gallons Per Minute 11 Gallons Per Minute 16 Gallons Per Minute 16 Gallons Per Minute Valve Auto Return Au
20. s be careful while backing your splitter You could jackknife your log splitter if not careful e Before using splitter disconnect it from tow vehicle A log could easily be POSITION pushed forward into the vehicle e See tire and wheel specifications for PSI while towing e Be aware of the extra length of splitter while turning parking crossing intersections and in all driving situations OPERATION INSTRUCTIONS POSI LOCK COUPLER ADJUST COUPLER LOCKING PRESSURE ON BALL BEFORE USE PLACE HANDLE IN LOCKED POSITION WITH BALL IN COUPLER TIGHTEN LOCKNUT AGAINST TENSION SPRING SO THAT COUPLER IS NOT LOOSE ON BALL CORRECT ADJUSTMENT WILL ALLOW HANDLE TO BE RELEASED WITH MODERATE PRESSURE APPLIED TO HANDLE TO OPEN PULL UP ON COUPLER HANDLE AND ROTATE FORWARD PLACE COUPLER ON BALL WHEN BALL IS COMPLETELY NESTED IN BALL SOCKET ROTATE COUPLER HANDLE BACKWARD UNTIL HANDLE IS IN LOCKED POSITION AFTER TOWING FOR 50 MILES CHECK COUPLER FOR TIGHTNESS ON BALL ALWAYS CHECK TIGHTNESS BEFORE TOWING BE SURE COUPLER HANDLE IS IN LOCKED POSITION WARNING NEVER EXCEED WEIGHT CAPACITY AND ALWAYS USE SAFETY CHAINS ALWAYS USE CORRECT BALL SIZE MAKING SURE BALL IS COMPLETELY INSERTED INTO COUPLER LOCK COUPLER HANDLE SECURELY BEFORE TOWING ALWAYS CHECK FOR DAMAGES AND REPLACE IF DAMAGED AVOID SHARP TURNS AND STEEP VERTICAL ANGLES WHEN TOWING A ASSEMBLY This log splitter has been partially assembled at the factory Refer to the drawin
21. swisherinc com OWNER S MANUAL MODEL NO Model LS12534H Shown LS722H STARTING SERIAL L206 010001 LS728H LS10528H LOG STARTING SERIAL L206 010001 e SPLITTER LS12534H12V STARTING SERIAL L206 010001 Safety IMPORTANT Read and follow all Safety Assembly Precautions and Instructions Operation before operating this e equipment Service and Adjustment Rev 06 164 Repair Parts 1602 CORPORATE DRIVE VVARRENSBURG MISSOURI 64093 PHONE 660 747 8183 Made In The FAX 660 747 8650 U S A Manufacturing quality lawn care equipment since 1945 12489 LIMITED VVARRANTY The manufacturer s warranty to the original consumer purchaser is This product is free from defects in materials and workmanship for a period of two 2 year from the date of purchase by the original consumer purchaser We will repair or replace at our discretion parts found to be defective due to materials or workmanship This warranty is subject to the following limitations and exclusions 1 Engine Warranty 2 Commercial Use 3 Limitation 4 Exclusions In the event you have a claim under this warranty you must return the product to an authorized service dealer All transportation charges damage or loss incurred during transportation of parts submitted for replacement or repair under this warranty shall be borne by the purchaser Should you have any questions concerning this warranty please contact us toll free at
22. tank prior to storage Always store gasoline in an approved tightly sealed container Store container in a dry cool place with adequate ventilation Keep fuel away from areas where fumes could contact open flame pilot light or sparks Be aware of the environment when disposing of used petroleum products Please dispose of used hydraulic fluid engine oil and any by products from the maintenance of your splitter at approved recycling centers Should it become necessary to disassemble the unit for repair or replacement of parts refer to the drawings and parts list on the following pages Exercise extreme caution as some parts are very heavy and will require sufficient persons or mechanical handling equipment Your Swisher Log Splitter has been produced with components designed specifically to this machine Although standard springs hardware and ect may look similar to parts used on other machinery they may in some cases be made of a different construction and or materials All replacement parts must meet manufacturer s specifications The operation of any splitter can produce foreign objects to be thrown into the eyes resulting in severe eye damage Always wear certified safety glasses or wide vision safety goggles over spectacles before staring any splitting machine and while operating such a machine The operation of any splitter produces sound waves that are damaging to the human ear Ear protection is recommended ery Ro de
23. to Return Belt Drive 1 1 Ratio with Belt Drive 1 1 Ratio with Clutch for Easy Starting Clutch for Easy Starting Hydraulic System Fluid 18 22 Quarts 19 23 Quarts 19 23 Quarts Capacity Drive System Clutch for Easy Starting Easy Starting 20 24 Quarts 25 1 2 4 00 X 4 80 X8 with High 4 00 X 4 80 X 8 with High Speed Bearings Speed Bearings E FERI i e a NOTES 4 00 X 4 80 X8 with High Speed Bearings 4 00 X 4 80 X8 with High Speed Bearings Tire Specs No 2 Ball 660 Lbs Auto Return Auto Return Belt Drive 1 1 Ratio with Belt Drive 1 1 Ratio with Clutch for Maximum Log length 25 1 2 25 1 2 jj 25 1 2 SVVISHER HISTORY Back before electricity came to rural Missouri Max Swisher was producing lawn mowers from his mother s chicken house Max never liked to mow grass He installed a gearbox on his family s lawn mower creating a self propelled unit By tying one end of a rope to the mower and the other end to a tree in the center of the yard the mower circled the tree shortening the rope and guiding the mower in concentric circles Max enjoyed relaxing under a shade tree while his invention did all the work Max had designed his first self propelled rotary lawn mower to do his dirty work for him Neighbors noticed his new invention and began asking him to make more Today 60 years later Swisher Mower and Machine Company Inc is still producing innovative lawn and garden and ATV UTV equipment d
Download Pdf Manuals
Related Search