Summer Infant 07050A User's Manual
Contents
1. 07050A Please read the following instructions carefully Keep this instruction manual for future reference Tools required Phillips head screwdriver not included For Technical Support Call 1 800 268 6237 or E Mail at customerservice summerinfant com AWARNING This product contains small parts Adult assembly required Exercise care when unpacking and assembling product For use with children birth and up INSTRUCTION MANUAL SURE AND SECURE DELUXE WOOD WALK THRU GATE Thank you for buying the Sure and Secure Deluxe Wood Walk Thru Gate from Summer Infant This pressure mounted gate helps you create and maintain a secure environment for your child It has a hinged swinging door that opens easily in either direction with one hand It also swings closed automatically It s fully adjustable to fit openings from 29 5 40 5 In normal use there is no need for mounting holes that damage woodwork and walls For added security use the mounting cups and screws that are provided Please read all the instructions before installing the gate WARNING IMPORTANT KEEP FOR FUTURE REFERENCE e To prevent serious injury or death securely install gate and use according to manufacturer s instructions e Never use with a child able to climb over or dislodge the gate e Never leave child unattended e Use only with lock securely engaged e Do not use if any components are missing or damaged e To prevent falls never use at t2. e gate making sure the gate is installed correctly as shown in Figure O We at Summer Infant stand behind all of our products If you are not completely satisfied or have any questions please contact our Customer Service Department at 1 800 268 6237 or e mail us at customerservice summerinfant com side view 2003 Summer Infant Inc 6 Blackstone Valley Place Suite 206 Lincoln RI 02865 USA 1 800 268 6237 www summerinfant com MADE IN CHINA Colors and styles may vary 7 05
3. f the gate frame is completely flat on the floor as shown in Figure E Optional mounting cup installation Fasten mounting cups to the doorframe or studs with screws as shown in Figure F If mounting into wall use wall anchors Note The adhesive mounting pads are included only for positioning the mounting cups and must be used in conjunction with screws OPERATION To open the gate see Figure N 1 slide the release button away from the door frame or wall 9 lift up the gate panel 3 swing open in either direction To close the gate Simply release the gate and it will close automatically Caution After closing the gate ALWAYS check to be certain that it is latched securely Troubleshooting If the gate does not stay closed 1 The Upper latch set is not properly adjusted Solution Adjust the upper tension knobs by turning them counter clockwise to release tension or clockwise to increase tension Ensure that the upper latch set MAINTENANCE 1 Regularly check tension knobs and rubber pads to make sure the gate is securely in place 2 Do not use the gate if any components are damaged or missing 3 Wipe surface with a damp cloth or sponge using mild detergent and warm water contacts the gate frame as shown in Figure IUU Ee e E e Distance should be a FIGURE QD FIGURE QD D gt Tighten both of the tension knobs on the bottom inward towards the frame at the same time as shown in Figu
4. op of stairs e This product will not necessarily prevent all accidents Proper adult supervision is required at all times A CAUTION KEEP SMALL PARTS OUT OF CHILD S REACH FEATURES amp COMPONENTS Upper Latch Set Gate Panel Gate Frame Extension Frames two Tension Bolts four Mounting Cups four Adhesive Mounting Pads four z228 Extension Pins four Screws four Wall Anchors four Wrench Lower Latch Set SET UP gt Center the gate in the opening so that the distance from the bottom of gate frame to each side wall is equal as shown in Figure H Use the marks etched into the wrench as a ruler Slide the tension bolts out until the pads contact the door frame or wall Then screw the tension knob away from the pad until it ap Measure the width of the opening where you intend to install the gate Please refer to the following pictures to determine the correct installation configuration FIGURE FIGURE FIGURE gt 29 o 331 2 without Extension Frame 337 0 371 2 with Extension Frame 37 2 40 5 with Extension Frame oP To use with extension frame assemble as shown in Figure D FIGURE Extension Frame Long end of Tension Gp Screw the tension knobs Bolt down the tension bolts until they contact the pads Insert 4 tension bolts into holes on outside and slide inward towards frame as far as possible lt gt Place the gate in the opening so that the bottom o
5. re J Then tighten both of the tension knobs on the top inward towards the frame at the same time as shown in Figure K so that the upper latch set goes below the release button completely as shown in Figure M To verify installation Push the frame to ensure that it is secure in the opening and then push the gate panel to ensure that the upper and lower latch sets Lower Latch Set FIGURE Note Wrench is provided for final tightening of all four tension knobs if necessary as shown in Figure G lock securely in the housings on the frame as shown in Figures L and M Tighten inward at the same time 4 mammur FIGURE C9 Upper Latch Set FIGURE Note If gate is difficult to unlatch top tension knobs may be too tight button always remains below the release button as shown in Figure M Also ensure that the upper latch set button engages securely when the gate swings closed and that it can be released properly when the release button is pushed 2 Lower latch set position is too low Solution Although unusual some door frames may be out of alignment In this case you may have to FIGURE adjust the individual tension knobs to ensure YH 0 iN that the gate is aligned properly Make sure N Bane the upper latch set is still below the release button as shown in Figure M If the gate does not stay in position it may not be installed properly as shown in Figure M Remove and reinstall th
Download Pdf Manuals
Related Search