Spirit IN839 User's Manual
Contents
1. 1 The warranty registration card must be completed and returned to the address listed on the card within 10 days of the original purchase to validate the manufacturer s limited warranty 2 Proper use of the treadmill in accordance with the instructions provided in this manual including belt tracking 3 Proper installation by an authorized Spirit service company in accordance with instructions provided with the treadmill and with all local electric codes 4 Proper connection to a grounded power supply of sufficient voltage replacement of blown fuses repair of loose connections or defects in house wiring 5 Expenses for making the treadmill accessible for servicing including any item that was not part of the treadmill at the time it was shipped from the factory 6 Damages to the treadmill finish during shipping installation or following installation EXCLUSIONS This warranty does not cover the following 1 CONSEQUENTIAL COLLATERAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY Note Some states do not allow the exclusion or limitation of incidental or consequential damages so this limitation or exclusion may not apply to you 2 Service call reimbursement to the consumer Service call reimbursement to the dealer that does not involve malfunction or defects in workmanship or material for units that are beyond the warranty period for units tha2. move too far back on the tread belt Pulling this safetv tether cord will stop tread belt movement To Use 1 Place the magnet into position on the round metal portion of the console control head Vour treadmill will not start and operate without this Removing the magnet also secures the treadmill from unauthorized use 2 Fasten the plastic clip onto vour clothing securelv to assure good holding power Note The magnet has strong enough power to minimize accidental unexpected stopping The clip should be attached securelv to make certain it does not come off Be familiar with its function and limitations The treadmill will stop depending on speed with a one to two step coast anvtime the magnet is pulled off the console Use the red 5 IN839 Stop Pause switch in normal operation Assembiv Instructions IN839 ASSEMBLV PACK LIST IN839 5 16 x 1 2 Button Head Socket Screw x2 5 16 x 3 4 Button Head Socket Screw x2 5 16 x 1 1 2 Button Head Socket Screw x2 5 16 x 19 x1 5T Curve Washer x2 M5 10 mm Button Head Socket Screws 4 Safety Key x1 Lubricant x1 Combination M5 Allen Wrench amp Screwdriver x1 Assembly IN839 STEP 1 Remove all parts from the carton As shown in Figure 1 STEP 2 Fasten the Left and Right Handrails onto the Frame Base with 2 pcs of 5 16 x3 4 Button Head Socket Screws 2 pcs of 5 16 x19x1 5T Curve Washers and 2pcs of 5 16 x1 1 2 Button Head Socke
3. Operation of Your Treadmill Getting familiar with the control panel IN839 Console inspire 77724 EAR PULSE ig ae N y SET MODE N 4 START FAST WINDOW DISPLAY SPEED Displays the current running speed from 0 8Mph 6Mph TIME Accumulates total workout time from 00 00 to 99 59 DISTANCE Accumulates total workout distance from 0 00 to 99 99 miles CALORIES Accumulates the user s calorie consumption during exercise Max Value is 9 IN839 PULSE INCLINE FUNCTION START STOP FAST SLOW MODE UP DOWN SET SAFETY KEY 999 9 calories Displays your current heart rate in beats per minute during workout from 40 to 220 Displays your current workout elevation from 0 to 15 BUTTONS Press START button to start training Press STOP button to stop training Press FAST button to increase your speed Each increment is 0 1 Press SLOW button to decrease your speed Each decrement is 0 1 Press button to select different displaying mode In stop mode you can set count down TIME DISTANCE CALORIES Press UP button to increase elevation position Each increment is 1 Press DOWN button to decrease elevation position Each decrement is 1 Press SET to clear data in exercise or setting count down Put safety key in position to power on the computer When safety key is pulled away from its position the computer will automatically shu
4. and walking running characteristics Some users will affect tracking differently Expect to make adjustments as required to center the treadbelt Adjustments will become less of a maintenance concern as the belt is used Proper belt tracking is an owner responsibility common with all treadmills ATTENTION DAMAGE TO THE RUNNING BELT RESULTING FROM IMPROPER TRACKING TENSION ADJUSTMENTS IS NOT COVERED UNDER THE SPIRIT WARRANTY BELT DECK LUBRICATION Do not re lube with other than Spirit lubricant Spirit provides one application with this unit See your Spirit dealer for additional purchases The use of some other lubricants may destroy the deck surface or belt and will void warranty Conditions exist beyond Spirit s control belt deck cleanliness which relates to friction You should apply the enclosed belt lubrication after approximately the first 50 hours of operation Use all the contents of one container no more and spread lubricant onto 12 IN839 middle portion awav from edges of the deck under treadbelt along its width When walked on the belt will make certain an even coat is applied Lubricant is not harmful to the skin Lube will be distributed properly by walking at 2 to 3 mph for 3 to 5 minutes on all areas of the belt Use handrails for support The first few minutes vou will be polishing your deck and lubricating the belt backing Do not run on a newly lubricated belt until the above break in procedure is done If the t
5. curacy of heart rate readings The pulse sensors are intended only as exercise aids in determining heart rate trends in general Use handrails provided they are for your safety Wear proper shoes High heels dress shoes sandals or bare feet are not suitable for use on your treadmill Quality athletic shoes are recommended to avoid leg 3 fatigue Remove tether cord after use to prevent unauthorized treadmill operation SAVE THESE INSTRUCTIONS THINK SAFETY Important Electrical Information WARNING e NEVER use a ground fault circuit interrupt GFCI wall outlet with this treadmill Route the power cord away from any moving part of the treadmill including the elevation mechanism and transport wheels e NEVER remove any cover without first disconnecting AC power e If voltage varies by ten percent 10 or more the performance of your treadmill may be affected Such conditions are not covered under your warranty If you suspect the voltage is low contact your local power company or a licensed electrician for proper testing See Diagnosis Guide page 13 e NEVER expose this treadmill to rain or moisture This product is NOT designed for use outdoors near a pool or spa or in any other high humidity environment Grounding Instructions This product must be grounded If the treadmill should malfunction or breakdown grounding provides a path of least resistance for electric current reducing the risk of electric shock This pr
6. e belt edge This should be done once a month to extend belt and bed life Use water only no cleaners or abrasives A mild soap and water solution along with a nylon scrub brush will clean the top of the textured belt Allow to dry before using Belt Dust This occurs during normal break in or until the belt stabilizes Wiping excess off with a damp cloth will minimize buildup General Cleaning Dirt dust and pet hair can block air inlets and accumulate on the running belt On a monthly basis vacuum underneath your treadmill to prevent buildup Once a year you should remove the black motor hood and vacuum out dirt that may accumulate UNPLUG POWER CORD BEFORE THIS TASK BELT ADJUSTMENTS Treadbelt Tension Adjustment Belt tension is not critical for most users It is very important for joggers and runners in order to provide a smooth steady running surface Adjustment must be made from the right side of the rear roller in order to adjust tension with the 6 mm Allen wrench provided in the parts package The adjustment bolt is located at the end of the right side rail as noted in diagram below Tracking Tension Adjustment Adjustment Side Only Side Only Note Adjustment is thru small hole of end cap 11 IN839 Tighten the rear roller only enough to prevent slippage at the front roller Turn the treadbelt tension adjusting bolt in increments of 1 4 turn and inspect for proper tension When an adjustment is made to the belt tens
7. e local dealership where vou purchased this treadmill is vour administrator for all Spirit warrantv and service needs Their responsibilitv is to provide vou with the technical knowledge and service personnel to make vour experience more informed and anv difficulties easier to remedv Please take a moment at this time to record the name of the dealer their telephone number and the date of purchase below to make anv future needed contact easv We appreciate vour support and we will alwavs remember that vou are the reason that we are in business Please complete and mail your registration card todav and enjov vour new treadmill Vours in Health Spirit Manufacturing Inc Name of Dealer Telephone Number of Dealer Purchase Date Product Registration RECORD YOUR SERIAL NUMBER Please record the Serial Number of this fitness product in the space provided below Serial Number REGISTER YOUR PURCHASE The self addressed product registration card must be completed in full and returned to Spirit Manufacturing Inc or visit www spiritfitness com to register online 2 IN839 Important Safety Instructions WARNING Read all instructions before using this appliance DANGER To reduce the risk of electric shock disconnect your Spirit treadmill from the electrical outlet prior to cleaning and or service work WARNING To reduce the risk of burns fire electric shock or injury to persons install the treadmill on a flat level surface wit
8. h access to a 120 volt 20 amp grounded outlet DO NOT USE AN EXTENSION CORD DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY USING IMPROPER ADAPTERS OR IN ANY WAY MODIFY THE CORD SET A serious shock or fire hazard may result along with computer malfunctions See Grounding Instructions page 4 Do not operate treadmill on deeply padded plush or shag carpet Damage to both carpet and treadmill may result Do block the rear of the treadmill Provide a minimum of 3 1 2 feet clearance between the rear of the treadmill and any fixed object Keep children away from the treadmill There are obvious pinch points and other caution areas that can cause harm Keep hands away from all moving parts Never operate the treadmill if it has a damaged cord or plug If the treadmill is not working properly call your dealer Keep the cord away from heated surfaces Do not operate where aerosol spray products are being used or where oxygen is being administered Sparks from the motor may ignite a highly gaseous environment Never drop or insert any object into any openings m Do not use outdoors To disconnect turn all controls to the off position remove tether cord then remove the plug from the outlet Do not attempt to use your treadmill for any purpose other than for the purpose it is intended The pulse sensors not medical devices Various factors including the user s movement may affect the ac
9. inspire BY as Malila Motorized Treadmill OWNER S MANUAL PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING YOUR NEW TREADMILL Table of Contents Produ i Registration A a bidet but Ad beta uration me poked mecca tab b 2 Important Safety Instriietibrisia i a a 3 Important Electrical Information g 4 Important Operation INStUG OMS xis feck esse ee nn 5 Assembly INS UGCHOM 6 Folding If structure b 8 Operation of Your New Treadmill 0 cece cece eee c cence cece eee ee 9 Maintenance of Your New 11 Service Checklist Diagnosis Guide 13 Manufacturers Limited Warrantv nn r rr rt 14 ATTENTION THIS TREADMILL IS INTENDED FOR RESIDENTIAL USE ONLV AND IS WARRANTED FOR THAT APPLICATION ANV OTHER APPLICATION VOIDS THIS WARRANTV IN ITS ENTIRETV 1 IN839 inspire BY CONGRATULATIONS VOUR NEW TREADMILL AND WELCOME TO THE SPIRIT FAMILVI Thank you for your purchase of this quality treadmill from Spirit Manufacturing Inc Vour new treadmill was manufactured bv one of the leading fitness manufacturers in the world and is backed bv one of the most comprehensive warranties available Through vour dealer Spirit will do all we can to make vour ownership experience as pleasant as possible for manv vears to come Th
10. ion you must also make a tracking adjustment to compensate for the change in belt tension This is accomplished by turning both the tension and tracking Allen bolts an equal amount This adjustment should be made by turning both bolts clockwise by no more than a 1 4 turn at a time DO NOT OVERTIGHTEN Over tightening will cause belt damage and premature bearing failure TREADBELT TRACKING ADJUSTMENT The performance of your treadmill is dependent on the frame running on a reasonably level surface If the frame is not level the front and back roller cannot run parallel and constant belt adjustment may be necessary The treadmill is designed to keep the treadbelt reasonably centered while in use It is normal for some belts to drift near one side while the belt is running with no one on it After a few minutes of use the treadbelt should have a tendency to center itself If during use the belt continues to move toward one side adjustments are necessary TO SET TREADBELT TRACKING A 6 Allen wrench is provided to adjust the rear roller Make tracking adjustments from the left side only Set belt speed at approximately 2 to 3 mph A small adjustment can make a dramatic difference Turn the bolt oniv a 1 4 turn and wait a few minutes for the belt to adjust itself Continue to make 1 4 turns until the belt stabilizes in the center of the CG gt running deck The belt may require periodic tracking adjustment depending on use
11. oduct is equipped with a cord having an equipment grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances DANGER Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded Do not modify the plug provided with the product if it will not fit the outlet have a proper outlet installed by a qualified electrician This product is for use on a nominal 120 volt circuit and has a grounding plug that looks like the plug illustrated below A temporary adapter that looks like the adapter illustrated below may be used to connect this plug to a 2 pole receptacle as shown below if a properly grounded outlet is not available The temporary adapter should be used only until a properly grounded outlet below can be installed by a qualified electrician The green colored rigid ear lug or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover Whenever the adapter is used it must be held in place by a metal screw Adapter Grounded Outlet Tab of Grounding Screw IN839 Important Operation Instructions e NEVER operate this treadmill without reading and completely understanding the results of any operational change you request f
12. ontact your selling authorized Spirit dealer OR 2 Contact your local authorized Spirit service organization 3 If there is a question as to where to obtain service contact our service department at 870 935 1107 4 If no local service is available Spirit will repair or replace the parts at Spirit s option within the warranty period at no charge for parts All transportation costs both to our factory and upon return to the owner are the responsibility of the owner The owner is responsible for adequate packaging upon return to Spirit Spirit is not responsible for damages in shipping Make all 14 IN839 freight damage claims with the appropriate freight carrier DO NOT SHIP ANV UNIT OUR FACTORV WITHOUT A RETURN AUTHORIZATION NUMBER AII units arriving without a return authorization number will be refused 5 For anv further information or to contact our service department bv mail send vour correspondence to Spirit Manufacturing Inc P O Box 2037 Jonesboro AR 72402 2037 Product features or specifications as described or illustrated are subject to change without notice All warranties are made by Spirit Manufacturing Inc This warranty applies only in the 50 states of the U S A and Canada IN839 Series Drive Motor 10 Years Labor 1 Year Electronics 2 Years Belt 2 Years Rollers 2 Years Frame Weldments Lifetime All Other Components 2 Years 15 IN839
13. ould be receiving power to operate Low AC voltage to treadmill Do not use an extension cord If an extension cord is required it should be as short as possible and heavy duty 16 gauge minimum Low household voltage Contact an electrician or your Spirit dealer A minimum of 110 volt AC current is required High belt deck friction See General Maintenance section on lubrication High belt deck friction See General Maintenance 13 IN839 touched a cold day while walking running Treadmill is not grounded Static electricity is crashing the computer Refer to Grounding Instructions on page 4 Manufacturer s Limited Warranty Effective October 15 2004 TREADMILL WARRANTY Spirit Manufacturing Inc warrants all its treadmills parts for a period of 2 years from the date of retail sale as determined by sale receipt or eighteen 18 months from the original factory shipping date whichever comes first Spirit s responsibilities include providing new or remanufactured parts at Spirit s option and technical support to our independent dealers and servicing organizations In the absence of a dealer or service organization these warranties will be administered by Spirit directly to a consumer An extended warranty period applies to the following components NORMAL RESPONSIBILITIES OF THE CONSUMER This warranty applies only to products in ordinary household use and the consumer is responsible for the items listed below
14. readmill belt deck is kept reasonably clean it is possible to expect over 1000 hours before additional re lubing is necessary CAUTION KEEP HANDS CLEAR OF MOVING REAR PULLEY Service Checklist Diagnosis Guide Before contacting your dealer for aid please review the following information It may save you both time and expense This list includes common problems that may not be covered under the treadmill s warranty PROBLEM Display does not light Treadbelt does not stay centered Treadmill belt hesitates when walked run on Motor is not responsive Display is lit Treadmill will only achieve approximately 7 mph but shows higher speed on display Treadbelt stops quickly suddenly when tether cord is pulled Treadmill trips on board 15amp circuit Computer shuts off when console is SOLUTION CAUSE Tether cord not in position Circuit breaker on front grill tripped Push circuit breaker in until it locks Plug is disconnected Make sure plug is firmly pushed into AC household wall outlet Household circuit breaker may be tripped Treadmill defect Contact your Spirit dealer A user may be walking while favoring or putting more weight on either the left or right foot If this walking pattern is natural track the belt slightly off center to the side opposite from the belt movement See General Maintenance section on Treadbelt Tension Adjust as necessary Make certain clock is running This indicates motor sh
15. rom the computer e Understand that changes in speed and incline do not occur immediately Set your desired speed on the computer console and release the adjustment key The computer will obey the command gradually e NEVER use your treadmill during an electrical storm Surges may occur in your household power supply that could damage treadmill components e Use caution while participating in other activities while walking on your treadmill such as watching television reading etc These distractions may cause you to lose balance or stray from walking in the center of the belt which may result in serious injury e NEVER mount or dismount the treadmill while the belt is moving Spirit treadmills start at a very low speed and it is unnecessary to straddle the belt during start up Simply standing on the belt during slow acceleration is proper after you have learned to operate the unit e Always hold on to a handrail or hand bar while making control changes incline speed etc Do not use excessive pressure on console control keys They are precision set to function properly with little finger pressure Pushing harder is not going to make the unit go faster or slower If you feel the buttons are not functioning properly with normal pressure contact your Spirit dealer Safety Tether Cord A safety tether cord is provided with this unit It is a simple magnetic design that should be used at all times It is for your safety should you fall or
16. t Screws by using the Combination M5 Allen Wrench amp Screwdriver As shown in Figure 2 Don t fasten these bolts tightly at this moment STEP3 Install the Console Support into the Left and Right Handrails with 2pcs of 5 16 x1 2 Button Head Socket Screw by using the Combination M5 Allen Wrench amp Screwdriver As shown in figure 3 STEP4 Plug the Computer Cable into the socket in back of Console As shown in figure 4 STEP5 6 IN839 Install the console into the Console Support with 4 pcs of M5 x 10 mm Button Head Socket Screws by using the Combination M5 Allen Wrench amp Screwdriver As shown in figure 5 PLEASE LOCK DOWN ALL HARDWARE AFTER THE ACCESSSORIES HAVE BEEN ASSEMBLED Assembly Instructions IN839 IN839 IN839 Folding Instructions Do not attempt to move the unit unless it is in the folded and locked position Be sure the power cord is secured to avoid possible damage Use both handrails to maneuver the unit to the desired position To Fold The Treadmill Pull the locking knob with left hand right hand lift the running deck up to 30cm then two hands lift it until it is locked by the locking knob To Unfold The Treadmill Pull locking knob and hold running board and lower down to the floor IN839 The treadmill is equipped with four transport wheels which are engaged when the treadmill is folded After folding simply roll the treadmill away 8 IN839
17. t are beyond the service call reimbursement period for treadmills not requiring component replacement or treadmills not in ordinary household use 3 Damages caused by services performed by persons other than authorized Spirit service companies use of parts other than original Spirit parts or external causes such as alterations modifications abuse misuse accident improper maintenance inadequate power supply or acts of God 4 Products with original serial numbers that have been removed or altered 5 Products that have been sold transferred bartered or given to a third party 6 Products that do not have a warranty registration card on file at Spirit Mfg Spirit reserves the right to request proof of purchase if no warranty record exists for the product 7 THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND OR FITNESS FOR A PARTICULAR PURPOSE SERVICE Keep your bill of sale Twelve 12 months from the date on the bill of sale or eighteen 18 months from the date of factory shipping as determined by the serial number establishes the warranty period should service be required If service is performed it is in your best interest to obtain and keep all receipts This written warranty gives you specific legal rights You may also have other rights that vary from state to state Service under this warranty must be obtained by following these steps in order 1 C
18. t down CONSOLE OPERATION START Put the safety key in position and all data will be displayed for 2 seconds then press button to begin exercising 2 While exercising you can press FAST SLOW button to adjust the speed manually 3 While exercising you can press STOP button to stop your workout or pull safety key away from its position to shut down the computer 4 In STOP mode press button to set count down time distance calories Press SET to clear data or press FAST and SLOW to adjust value You can set single or multi data that you have set data will count down and others data will count up After setting press START to start training 5 If after pressing STOP button to stop the treadmill and you want to resume your workout you can press START button again to start the treadmill then all previous data will resume counting 10 IN839 ERROR MESSAGE ERR Treadmill doesn t receive the speed signal for 6 seconds or controller fault then treadmill will stop Restart the treadmill after fixing the problem General Maintenance Belt and Bed Your treadmill uses a very high efficient low friction bed Performance is maximized when the bed is kept as clean as possible Use a soft damp cloth or paper towel to wipe the edge of the belt and the area between the belt edge and frame Also reach as far as practical directly under th
Download Pdf Manuals
Related Search