Spectra HR150U User's Manual
Contents
1. Press the power audio button to turn on the receiver Note When the receiver is initially turned on all LEDs and the audio signal turn on for one second diagnostic mode Note The on grade LED flashes once every two seconds to show that the receiver is on 2 Press and hold the power audio button for two seconds to turn off the receiver Note When the receiver is being turned off all the LEDs and the audio signal quickly turn on for one second Selecting the Audio Function The receiver always starts up with the audio mode active 1 Press the power audio button repeatedly to turn on off the audio function Note If the audio function is on the receiver beeps quickly when the receiver is above the laser beam slowly when below it and continuously when centered in the laser beam or on grade Receiver Features and Functions 1 Power Audio Button is a multi functional button that turns on off the receiver and audio function 2 Marking Notches both sides align with the on grade portion of the photocell and are used to mark elevation readings The marking notches are 50mm 2 inches from the top of the receiver 3 LEDs front and back show the position of the receiver relative to the laser beam high on grade or low and indicate power and low battery status 4 Level Bubble is used to make sure that the receiver is level Photocell detects the laser beam when it strikes the receiver 6 Audio2. HR150 Receiver User Guide SPECTRA PRECISION TASER Cy www trimble com E gt Trimble How to Use the Receiver Installing Removing the Batteries 1 Release the battery door using your fingers a coin or a screwdriver Open the door 2 Install Remove the 2 AA batteries noting the positive and negative diagram on the bottom of the battery housing 3 Close the battery door and latch it shut Introduction Thank you for choosing the Spectra Precision Laser Receiver HR150 from the Trimble family of precision instruments The HR150 is a battery operated laser receiver that detects a rotating laser beam and indicates its position relative to the beam using LEDs Before using the receiver be sure to read this user guide carefully Included in it is information about setting up using and maintaining the receiver Also included in this manual are CAUTIONS and Notes Each of these words represents a level of danger or concern A CAUTION indicates a hazard or unsafe practice that could result in minor injury or property damage A Note indicates important information unrelated to safety Your comments and suggestions are welcome please contact us at Trimble Construction Division 5475 Kellenburger Road Dayton Ohio 45424 1099 U S A Phone 937 245 5600 800 538 7800 FAX 937 233 9004 Internet www trimble com 2 Learning the Receiver Functions Turning On Off the Receiver 1
3. Port is the opening the sound comes out of Using the Receiver with a Laser 1 Press the power audio button to turn on the receiver 2 Position the receiver so that its photocell faces the laser 3 Move the receiver up down until the LEDs show an on grade reading Note The top bottom red LEDs flash when the receiver is above or below the laser beam The green LED flashes when the receiver is on grade High On Grade Low Battery Low Power Audio Button Audio Port 7 Clamp Tab Recess is the area that the general purpose clamp s release tab fits into Label shows the serial number and bar code oo Ne Magnet holds the receiver on a wall molding cross T runner etc 10 Battery Housing holds two AA alkaline or Ni Cd batteries 1 Battery Door holds the batteries securely in place D 12 Neck Cord Holder allows a neck cord to be attached to the receiver LED Audio Information LED Audio Indication Audio Output Green LED flashes Receiver is on N A once every two seconds Top red LED flashing Fast beeping tone Bottom red LED Low Slow beeping tone flashing Speaker beep Both red LEDs Low battery N A flashing in sequence General Purpose Clamp The C61 general purpose clamp allows the receiver to be attached to a survey rod or wooden pole Features and Functions 1 Release Tab allows the receiver to be locked onto or released from the genera
4. chase and use of its equipment Trimble will not be held responsible for any consequential loss or damage of any kind This warranty is in lieu of all other warranties except as set forth above including any implied warranty merchantability of fitness for a particular purpose are hereby disclaimed This warranty is in lieu of all other warranties expressed or implied 15 Notice to Our European Union Customers For product recycling instructions and more information please go to www trimble com environment summary html Recycling in Europe To recycle Trimble WEEE call 31 497 53 2430 and ask for the WEEE associate or mail a request for recycling instructions to Trimble Europe BV c o Menlo Worldwide Logistics Meerheide 45 5521 DZ Eersel NL 12 Trimble Trimble Construction Division 5475 Kellenburger Road Dayton Ohio 45424 1099 U S A 1 937 245 5600 Phone www trimble com nz 2006 Trimble Navigation Limited All rights reserved Reorder PN 1277 7571 11 06
5. e Automatic Shutoff 30 minutes after last laser detection or push button actuation Spectral Sensitivity Operates with red visible and infrared rotating lasers with wavelength between 610 and 900 nm Marking Notch 50 mm 2 in below top of receiver on both sides Operating Temperature 20 C to 50 C 4 F to 122 F Storage Temperature 40 C to 70 C 40 F to 158 F SiS Dimensions H x W x D 13 6 x 5 0 x 2 8 cm 5 37 x 2 00 x 1 11 in 11 Warranty Trimble warrants the receiver to be free of defects in material and workmanship for a period of one year Trimble or its authorized service center will repair or replace at its option any defective part for which notice has been given during the warranty period If required travel and per diem expenses to and from the place where repairs are made will be charged to the customer at the prevailing rates Customers should send the product to Trimble Navigation Ltd or the nearest authorized service center for warranty repairs freight prepaid In countries with Trimble subsidiary service centers the repaired product will be returned to the customer freight prepaid Any evidence of negligent abnormal use accident or any attempt to repair the product by other than factory authorized personnel using Trimble certified or recommended parts automatically voids the warranty The foregoing states the entire liability of Trimble regarding the pur
6. l purpose clamp 2 Jaws close open so that the general purpose clamp can be attached to or released from a survey rod or wooden pole 3 Reading Edge aligns with the receiver s on grade marking notches 4 Jaws Screw controls the closing opening of the jaws Circular Bubble Screw Holes are where the optional 1277 6251S grade rod circular bubble kit is mounted mi Gis EMC Declaration of Conformity This receiver has been tested and found to comply with the limits for a Class B digital device for radio noise for digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communication and is pursuant to part 15 of the Federal Communication Commission FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This receiver generates radio frequency If it s not used in accordance with the instructions it may cause harmful interference to radio or television reception Such interference can be determined by turning the receiver off and on You are encouraged to try eliminating the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the laser and the receiver For more information consult your dealer or an experience radio television technician CAUTION Changes or modifications to the receiver that are not expressly approved by Tri
7. mble could void authority to use the equipment 2B Attaching the Receiver to the Survey Rod or Wooden Pole I Slide the general purpose clamp into the receiver until it clicks into position Turn the jaws screw counterclockwise to open the clamp s jaws Slide the survey rod or wooden pole between the clamp s jaws Turn the jaws screw clockwise to hold the general purpose clamp securely in place lnndadundadundedunds Q9 Declaration of Conformity Application of Council Directive s Manufacturer s Name Manufacturer s Address 25 l EE 10 89 336 EEC Trimble Navigation Ltd European Representative Address Model Number Conformance to Directive s Equipment Type Environment Product Standards 5475 Kellenburger Road Dayton Ohio 45424 1099 U S A Trimble GmbH Am Prime Parc 11 65479 Raunheim Germany HR150 EC Directive 89 336 EEC using EN55022 and EN50082 1 ITE residential commercial amp light industrial Product meets the limit B and methods of EN55022 Product meets the levels and methods of IEC 801 2 8 kV air 4 kV contact IEC 801 3 3 V m 26 to 1000 MHz 80 1 kHz Receiver Specifications Capture Height 50 mm 2 in On Grade Sensitivity Medium 3 00 mm 1 8 in Power Source Two 1 5 V batteries type LR6 AA Battery Life 20 C 68 F Alkaline 70 hours Low Battery Indicator Red LEDs flash in sequenc
Download Pdf Manuals
Related Search