Sony NSZ-GS7 User's Manual
Contents
1. Change the input of the TV to display the signal from this player Make sure that the power indicator is lit uo white as illustrated below D Power indicator Try the following Turn the player off and on again Turn the connected device off and on again Disconnect and reconnect the HDMI cable Disconnect the AC power cord from the player and reconnect it after about two minutes The HDMI OUT jack is connected to a DVI device that does not Support copyright protection technology The player cannot connect to the Internet Make sure that the LAN router or Wireless LAN router is on Make sure that the LAN cable is connected correctly when using a wired network connection Check the settings of the LAN router or Wireless LAN router For details refer to the operating instructions supplied with the LAN router or Wireless LAN router Move the player and the Wireless LAN router closer to each other The Wireless LAN connection is affected by the surrounding environment the wall material radio wave receiving condition obstacles between the player and the Wireless LAN router etc Move the player away from devices that use a 2 4 GHz frequency band microwaves Bluetooth devices cordless digital devices etc or turn off such devices These devices may interrupt the communication between the player and the Wireless LAN router f you cannot get Wi Fi over the Internet please make sure you do not2. Enter to pair your remote with the player Complete the Network setup process otherwise the Initial Setup Wizard cannot be closed t takes about 15 minutes to complete the Initial Setup This player is equipped with a built in IR Blaster that accepts remote commands and sends them to various connected devices to control them with your remote This function works when the player is turned on When you set the player close to a connected device as illustrated on the right you can control the device using the remote including operations such as adjusting the volume of the TV or an AV Receiver However if you place the player in a location where IR signals cannot reach you cannot control connected devices with the built in IR Blaster In this case connect the supplied IR Blaster as follows Connect the IR Blaster cable to the player 2 Place the IR Blaster so that the infrared transmitter points to the IR receiver sensor on the device you want to control as illustrated on the right CLIR Blaster I R I BLASTER t I a S Location of the IR receiver may vary depending on the product you are using Troubleshooting There is no picture screen is dark Make sure that the AC power cord is securely connected Make sure that all the connecting cables are securely connected Especially make sure HDMI IN and OUT are correctly connected
3. have a LAN cable connected The player places priority on a LAN connection over a Wi Fi connection Product Registration Please take a few minutes to register your product This also allows us to contact you with important product notifications or provides a record in case of product loss or theft From your player Press HOME and select All Apps Product Registration From your PC For customers in the USA http productregistration sony com For customers in Canada http www sony ca register The picture from the Set Top Box is not output correctly via an AV Receiver Make sure that HDMI cables are connected securely to the Set Top Box and to the player Turn the Set Top Box off then turn it on again f the picture is still not output correctly reconnect the TV directly to the player and connect AV Receiver and the player with an optical digital cable as illustrated below Network Media Player OUT SS IN HDMI cable Optical digital cable HDMI cable OUTS Set Top Box 1 Supplied NSZ GX70 only 2 Not supplied When this player and the TV are connected with HDMI cables via an AV Receiver pictures may not be displayed properly due to the copyright protection feature of some Set Top Boxes In this case contact your Cable Satellite TV Operators The remote does not function Make sure that the batterie
4. SONY Network Media Player NSZ GS7 NSZ GX70 NSZ GX70 is only for the US Connection step Quick Setup Guide Sony Customer Support USA http esupport sony com 1 800 222 SONY Canada http esupport sony com CA 1 877 899 SONY Please Do Not Return the Product to the Store Connect to your TV Follow A to connect to your TV directly B to connect to your TV via AV Receiver C if your connection differs from the diagrams below A Direct to TV IN C TV optional Set Top Box Digital Video Recorder step Wireless LAN router 1 2 Broadband router h Prepare for Network connection lt E UT E IN HDMI cable supplied with NSZ GX70 only TV CN Him OUT v v GS HDMI cable not supplied optional Set Top Box Digital Video Recorder step AC power cord In the Box _ Network Media Player Remote control Remote 1 To insert batteries into the remote control B To TV via AV Receiver o AV Receiver HDMI cable supplied with NSZ GX70 only HDMI a e HDMI cable not supplied Connect to the power source Connect to the power source 2 Change the TV input Switch the input selector on the TV so that the signal from the player appears on your TV screen Then a screen that shows how to setup your remote appears N
5. ote LAN cable not supplied This will only appear the first time you setup your player 1 When using wireless connection you need to set the Network Setup in the Initial Setup Wizard on step 4 2 You can find MAC address in the Initial Setup Wizard step 4 as needed Select Explain step on Connect to the Internet screen To control connected devices using the remote 2012 Sony Corporation Printed in China 4 421 770 11 2 tT 442177011 AC power cord 1 HDMI cable 1 NSZ GX70 only size AA batteries 2 Quick Setup Guide 1 Getting Started 1 Reference Guide and other documents What s this The IR Blaster enables you to control connected devices with your remote Please see To control connected devices using the remote shown below for more information IR infrared Blaster cable 1 c C Other connection See Help Guide for other connection patterns From your PC http www sony net helpguide r networkplayer From your smartphone Start the Initial Setup Wizard step Follow the directions for the Initial Setup displayed on screen The screen may stay dark for several seconds after the sony logo appears then the Initial Setup screen appears When the Initial Setup screen on which a picture of a player and a hand holding a remote is displayed appears press and hold
6. s are inserted correctly Operate the remote closer to the player Disconnect and reconnect the AC power cord Perform re pairing according to the following procedure Press the CONNECT button located on the bottom of the player with a thin sharp object such as the point of a pen etc 2 Follow the instructions on the screen Use a thin sharp object such as the point of a pen to press the CONNECT button f the touch pad of the remote is not operated for a while it will not sense any attempts at operations When you want to use It again hold the remote up or after clicking the touch pad lift your finger off it for a few seconds Do not cover the upper left part of the remote because that is where the antenna is located The remote may malfunction or may not work properly if you cover the antenna
Download Pdf Manuals
Related Search