Sony SCH-735 User's Manual
Contents
1. SENSITIVITY You can select up to 8 MD areas When SENSITIVITY number is high motion detection sensitivity is increased to recognize even MASK COLOR Determine area color You can select Gray Green Red Blue small movement Black White AREA MODE Determines whether to use the MD area selected in SENSITIVITY TRANSP Determine the transparency of selected area as controlling number SEL POS Determines which of the 4 vertices of each MD area is to be used from 0 to 3 YPOS Determines the coordinate of the vertical axis for SEL POS RETURN Select this to save the PRIVACY menu settings and return to the XPOS Determines the coordinate of the horizontal axis for SEL POS SPECIAL menu COLOR CCD CAMERA 36 User Guide COLOR CCD CAMERA 137 User Guide How to Use the Camera DIS Digital Image Stabilizer This function mitigates any picture movement due to external factors such as wind Notes e The chance of resolution decrease is existed because DIS function uses the digital zoom e DIS doesn t operate when background illumination is too low e DIS doesn t operate when object pattern is monotonic as like sky or white wall If Digital Image Stabilizer DIS is enabled the digital zoom is not configured to less than 46 level COMM ADJ Communication Adjustment This function sets up the camera communication status when controlling the camera through an external control device2. Some lenses may not work properly depending on the setting of the BRIGHTNESS LEVEL e When Using a Video Type Auto Iris Lens Disable AGC mode of EXPOSURE menu Adjust the ALC adjustment terminal on the lens properly Typically the terminal is set to AV Average Make an image as bright as you want by adjusting the lens LEVEL VR Set AGC mode to ON under EXPOSURE menu after adjusting the lens LEVEL VR If the image looks brighter than it should return to and adjust the LEVEL VR again The lens LEVEL VR may not work properly depending on the lens used 24 O Manual Select Manual Lens gt 2 EXPOSURE How to Use the Camera 1 When the SETUP menu screen is displayed select EXPOSURE by using the Up and Down buttons so that the arrow indicates EXPOSURE 2 Select a desired mode using the Up and Down buttons EXPOSURE SETUP P1 SHUTTER 2 AGC HIGH 3 SENS UP OFF 4 RETURN SHUTTER You can select either auto or manual shutter A FLK Select this when you experience picture flicker which can happen when there is a clash with the frequency of the installed lighting ESC Select this to control the shutter speed automatically If ESC is selected the shutter speed is automatically controlled depending on the ambient illumination of the subject MANUAL You can control shutter speed manually amp Notes To produce better results with A FLK do
3. COMMUNICATION SETUP Press SET to Return When the SPECIAL menu screen is displayed press the Up and Down buttons so that the arrow indicates COMM ADJ Set up the mode using the 4 direction buttons CAMID Determines the camera s identification number between 0 and 25 BAUD RATE You can select 2400 4800 9600 19200 38400 57600 bps UART MODE You can select NONE EVEN or ODD for the parity bits Determines whether to send a command back to the controller device when a communication control command is sent to the camera DISP CAM ID Display camera title on top left corner of the screen O LANGUAGE You can select the menu language according to your requirements O RESET Resets the camera settings to the factory defaults RETURN Select this to save the SPECIAL menu settings and return to the SPECIAL menu EXIT Press the SET button in the EXIT menu to save the current settings and exit the SET menu COLOR CCD CAMERA 38 User Guide J Troubleshooting If you have trouble operating your camera refer to the following table If the guidelines do not enable you to solve the problem contact an authorized technician Nothing appears on the screen Check that the power cord and line connection between the camera and monitor are fixed properly Check that you have properly connected VIDEO cable to the camera VIDEO output jack The image on the screen is dim e Is lens stained with dirt
4. Supreme Resolution WDR Camera SHC 735 User Guide Before installing and operating this product please read this manual thoroughly ENGLISH Before operating the camera confirm the camera model and proper input power voltage In order to that you can understand this manual thoroughly we ll introduce our model description E SHC 735 SERIES e NTSC MODELS ePAL MODELS SHC 735N SHC 735P SHC 735PH m MODEL DESCRIPTION e SHC 735X X L POWER SOURCE SIGNAL SYSTEM e SIGNAL SYSTEM N gt NTSC MODEL P gt PAL MODEL e POWER SOURCE gt DC12V AC24V 5AC 230V CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute arisk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance INFORMATION This equipment has been tested and found to comply with limits for a Class A digital device pursuant to part 15 of the FCC Rules These
5. We the undersigned hereby declare that the equipment specified above conforms to the above Directive s Manufacturer SAMSUNG TECHWIN CO LTD Signature IZA 7 WS Chu Full Name BONJENG GU Position QUALITY CONTROL MANAGER Place CHANGWON KOREA Date 2008 02 01 Legal Representative in Europe Signature Full Name Position Place Date COLOR CCD CAMERA m User Guide SAMSUNG TECHWIN SALES NETWORK SAMSUNG TECHWIN CO LTD 145 3 Sangdaewon 1 dong Jungwon gu Seongnam si Gyeonggi do Korea 462 703 TEL 82 31 740 8151 8 FAX 82 31 740 8145 SAMSUNG TECHWIN EUROPE CO LTD SAMSUNG TECHWIN AMERICA Inc Samsung House 1000 Hillswood Drive Hillswood Business 1480 Charles Willard St Carson CA 90746 UNITED STATES Park Chertsey Surrey KT16 OPS Tol Free 1 877 213 1222 FAX 1 310 632 2195 TEL 44 1932 45 5300 FAX 44 1932 45 5325 www samsungtechwin com www samsungcctv com P No Z6806 0828 01F VAN 09 10
6. Clean your lens with soft clean cloth Set the monitor to proper condition e If the camera is exposed to too strong light change the camera position The image on the screen is dark e Adjust the contrast feature of the monitor or DVR If you have an intermediate device set the 750 Hi z properly The camera is not working properly and the surface of the camera is hot Check that you have properly connected the camera to an appropriate power source The DAY NIGHT menu does not work e Check that AGC of EXPOSURE SETUP menu is OFF The SENS UP function does not work e Check that AGC of EXPOSURE SETUP menu is OFF e Check that SHUTTER of EXPOSURE SETUP menu is A FLK or MANUAL The Motion Detection function does not work e Check that MOTION DEF of SPECIAL SETUP menu is OFF Color is not correct e Check the setting of WHITE BAL SETUP menu The screen flickers continually Check that direction of camera turns toward the Sun RS 485 communication fails Check the polarity between RS 485 Control Port and RS 485 cable 485 Control Board Connection Port RS 485 Control Port CONNECTION TERMINAL TRX 485 CONNECTION TERMINAL TRX 485 e Check the RS 485 Communication establishment initial value RS 485 Communication establishment initial value Item CameralD BAUDRATE UARTMODE _ RET PKT Initial value 1 9600 8 NONE 1 ENABLE We recommend that you make ground connect between camera and
7. The use of equipment such as an aerial ladder while providing after sales service shall be at your expense Separate the power plug when thunder crashes or lighting flashes This product is support equipment for surveillance system Therefore we can t compensate for material loss and or personal injuries by robbery fire natural disaster or something like this type Warning Attention Special Mark Messages Ignoring this information may result in material loss and or serious personal injuries including death Ignoring this information may A result in material loss and or a slight injuries Indicates Never Allowed O Indicates No Disassembling Correct Disposal of This Product Waste Electrical Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users
8. There may be some deviation in voltage drop depending on the type of wire and the manufacturer Control via RS 485 Interface The camera can be controlled by using external controllers like a Remote controller RS 485 Communication 1 To control by PC Connect the RS 485 control port of the camera and the serial cable through an RS 485 converter Example PC Serial Port COM1 gt Serial Cable s RS 485 Converter gt Camera RS 485 Control Port 2 To control using a DVR or System Controller Connect the RS 485 cable TRX TRX to the connection port of the 485 control board that is connected to the DVR or System Controller 485 Control Board Connection Port RS 485 Control Port CONNECTION TERMINAL TRX 485 CONNECTION TERMINAL TRX 485 RS 485 Communication establishment initial value Item Camera ID BAUD RATE UART MODE RET PKT Initial value 1 9600 8 NONE ENABLE Notes e To control the camera by constructing an additional controller use Pelco D protocol or STW protocol Samsung Techwin protocol COLOR CCD CAMERA 20 User Guide Setup Menu LENS DC VIDEO MANUAL e SHUTTER EXPOSURE SENS UP MANUAL SET ARS AIW e OUTDOOR INDOOR OFF BACKLIGHT er BLC e WDR SSNR ON OFF e COLOR DAYINIGHT m AUTO IMAGE ADJUSTMENT e V REV e D Z00M e H REV IMAGE ADJ OOO SHARPNESS CAMTITLE SYNC e MOTION DET SPE
9. com Auto Iris Lens Connector Tripod Mounting Bracket Screw Hole Used to connect Auto Iris Lens plug Used to fix the camera on a bracket or tripod The screw sizes for this hole are as follows 1 4 20 UNC 20 THREAD L 4 5mmz0 2mm ISO standard or 0 197 ASA standard You can separate the Tripod Mounting Bracket and install it on the top or bottom of the camera Make sure to use the Tripod Mounting Bracket when fixing the camera to a bracket or tripod Otherwise the camera may not be secure or the internal circuitry of the camera may be damaged 4 High Voltage Type SHC 735PH Function Setup Button SET Button Displays the menu on the screen Press this button to confirm status or after changing a selected item Up and Down Button Used to move the cursor up or down in the menu screen to select a desired menu item Left and Right Button Used to move the cursor left or right in the menu screen or to change the value of the selected item amp N Input Port You can switch to Day 8 Night Mode by connecting an external signal to this port MD Output Port Motion detection signals are output through this port RS 485 Control Port You can control SETUP MENU through this port by using external controllers like a Remote controller that RS 485 Communication is supported For details see page 21 Video OUT Port Video s
10. controller in order to maintain safety communication control COLOR CCD CAMERA 39 User Guide Specifications SHC 735 SHC 735P SHC 735PH ELECTRICAL Input Voltage AC 24V DC 12V AC230V Power Consumption Max 4 0W VIDEO Imaging Device Diagonal 6mm 1 3 Color Vertical double density interline CCD 41k Total Pixels 811 H x 508 V 795 H x 596 V Effective Pixels 768 H x 494 V 752 H x 582 V Scanning System 2 1 Interlace Synchronization internal Line Lock Frequency 15 734KHz V 59 94Hz H 15 625KHz V 50 00Hz Horizontal Resolution COLOR 560 V lines Min B amp W 700TV lines Min Min Illumination COLOR 0 3Lux 50 IRE F1 2 0 001Lux SENS UP x256 amp W 0 01Lux 50 IRE F1 2 0 00004Lux SENS UP x256 S N Y Signal 52dB AGC Off Weight On Video Output CVBS 1 0Vp p 750 OPERATIONAL IRIS Adustment C VIDEO Electronic Shutter Speed 5 Manual A I Fixed NTSC 1 60 1 120 000 PAL 1 50 1 120 000 On Screen Display AL ENGLISH TSC KOREAN ENGLISH JAPANESE SPANISH FRENCH PORTUGUESE FRENCH GERMAN SPANISH ITALIAN CHINESE PORTUGUESE DECLARATION OF CONFORMITY Application of Council Directive s Manufacturer s Name Manufacturer s Address European Representative Name European Representative Address Equipment Type Environment Model Nam
11. level is increased this is normal White Balance White Bal Use the White Balance function to adjust the screen color 1 When the SETUP menu screen is displayed select White Bal by using the Up and Down buttons so that the arrow indicates White Bal 2 Select a desired mode using the Up and Down buttons MAIH SETUP 1 LENS oc e 2 EXPOSURE 1 gt 3 WHITE BAL ATH 4 BACKLIGHT OFF 2 Select one of the following 5 modes as appropriate for your purpose ATW Select this when the color temperature is between 1 800 and 10 500 K COLOR CCD CAMERA 25 User Guide How to Use the Camera INDOOR Select this when the color temperature is between 4 500 K and 8 500 K UTDOOR Select this when the color temperature is between 1 800 K and 10 500 K sodium light inclusion AWC SET To find the optimal setting for the current luminance environment in this mode set the point the camera towards a sheet of white paper and press the SET button If the environment changes readjust it MANUAL Select this to fine tune White Balance manually Set White Balance first by using the ATW or AWC mode After that switch to MANUAL mode fine tune the White Balance and then press the SET button Press SET to Return Notes e White Balance may not work properly under the following conditions In this case select the AWC mode When the color temperature of environment surrounding the
12. limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARNING Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment WARNING To prevent electric shock and risk of fire hazards 4 Do NOT use power sources other than that specified 4 Do NOT expose this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes m How to Set up the Functions Front View aaa BACKLIGHT nee e SSNR oo Bottom View nku an e DAY NIGHT II Rear View nennen Rennen SIMAGEND ne nee SPECIAL e When Using Auto Iris Lens When Using C CS Mount Lens Connecting a Monitor Connecting Power Control via RS 485 Interface Features Ultra High Resolution By adopting a double speed 410 000 pixel Sony CCD the camera produces clear picture quality with a horizontal resoluti
13. not use it in conjunction with the WDR mode of the BACKLIGHT menu When the SHUTTER is set to ESC after selecting the Internal Synchronization Type the picture may become unstable if the camera faces a bright fluorescent light Therefore take care when choosing the installation position e When you use DC lens set the shutter mode to fixed if Color Rolling is occurred e When the SHUTTER is set to MANUAL or A FLK mode SENS UP will be disabled AGC AUTO GAIN CONTROL The higher the gain level the brighter the screen but the higher the noise OFF Deactivates the AGC function LOW Allows automatic gain control from 0 to 30dB HIGH Allows automatic gain control from 0 to 42dB COLOR CCD CAMERA 24 User Guide O SENS UP When it is night or dark the camera automatically detects the light level and maintains a clear picture if this mode is activated OFF Deactivates the SENS UP function AUTO Activates the SENS UP function RETURN Select this to save the changes in the EXPOSURE menu and return to the SETUP menu Press SET to Return Q Notes e If you press the SET button in AUTO mode You can adjust brightness by increasing or decreasing the shutter speed X2 X256 e Note that the higher the zoom level the brighter the screen but the more likely it is that an after image will appear e Although Noise Spots and Whitish symptoms may occur in SENS UP operation when the zoom
14. one e Only English is available in this mode Press the SET button O Use the 4 direction buttons to move to a desired letter and select the letter by pressing the SET button Repeat this to enter multiple letters You can enter up to 15 letters Notes e If you move the cursor to CLR and press the SET button all the letters are deleted To edit a letter change the cursor to the bottom left arrow and press the SET button Move the cursor over the letter to be edited move the cursor to the letter to be inserted and then press the SET button Enter a title move the cursor to POS and press the SET button The entered title appears on the screen Select the position to display the title on the screen by using the 4 direction buttons and press the SET button When the position is determined select END and press the SET button to return to the SPECIAL menu How to Use the Camera O SYNC In areas where the supply is at 60Hz you can FILL gt SET Fills in a selected MD area Fills in a selected MD area The color of synchronize the output phase of multiple filling is sequentially selected as brown orange blue cyan cameras using the power synchronization PHASE mr yellowish green yellow and red function Line Lock without using a RETURN Select this to save the MOTION DET menu settings and return to the synchronization signal generator SPECIAL menu INT
15. subject is out of the control range e g clear sky or sunset When the ambient illumination of the subject is dim Ifthe camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically the White Balance operation may become unstable BACKLIGHT This camera is designed so that it delivers a distinctive subject and background at the same time even when the subject is in backlight unlike conventional cameras by adopting a proprietary SV IV DSP chip 1 When the SETUP menu screen is displayed select BACKLIGHT by using the Up and Down buttons so that the arrow indicates BACKLIGHT COLOR CCD CAMERA 26 User Guide MAIN SETUP 1 LENS 0 1 2 EXPOSURE el 3 UHITE BAL ATU gt 4 BACKLIGHT OFF 5 SSR DH 1 2 Select a desired mode using the Left and Right buttons depending on the camera purpose O BLC Enables a user to directly select a desired area from a picture and to view the area more clearly e Select BLC to adjust the area to be enhanced and BLC SETUP enhancement level TOP BOTTOM LEFT RIGHT LEVEL Press SET to Return WDR When there are both bright and dark areas at the same time this mode makes both areas distinctive lt WDR gt lt OFF gt e Select WDR to adjust the WDR LIMIT and LEVEL LIMIT Adjust the WDR Sensitivity by selecting LOW MIDDLE or HIGH pena LEVEL Adjust t
16. CIAL e PRIVACY DIS e COMM AD e LANGUAGE RESET e RETURN EXIT How to Set up the Functions You can set up functions using the 5 buttons on the rear of the camera UP button SET button LEFT button DOWN button RIGHT button COLOR CCD CAMERA 20 User Guide 1 Press the SET button e Main setup menu is displayed on the monitor screen Select the function using the UP or DOWN button Bb 1 LENS hange the status using e LEFT or RIGHT button 2 Select a desired function using the Up and Down buttons e Place the cursor over a desired item 3 Set up a selected item by using the Left and Right buttons 4 To finish the setting select EXIT and press the SET button An item with the 4 icon also has sub menus To select a sub menu select an item with the icon and press the SET button e An item with the icon is unavailable due to function settings Using this function you can control screen brightness 1 When the SETUP menu screen is displayed select LENS by using the Up and Down buttons so that the arrow indicates LENS 2 Select the connected lens type by using the Left and Right buttons gt i LEHS DCNideo Select Auto Iris Lens e When DC is selected you can control screen brightness The range of brightness control is between 1 and 70 Adjust the brightness appropriately for optimal screen brightness
17. Internal Synchronization Type 5 UL Power Synchronization Type Line lock Notes Press the SET button tdi You can select a desired phase from 0 to 359 when select phase nit T Only MOTION DET mend Therefore MD arcas donit display onthe You can decide the synchronization between luminance and color signal when select the mode PRIVACY Hide an area you want to hide on the screen 9 Notes When the SPECIAL menu screen is displayed press the Up and Down buttons so that the arrow indicates PRIVACY e When using AC power at 60Hz frequency you can use the L L type synchronization When the power is DC 12V the SYNC menu is fixed to the INT mode PRIVACY REA MODE om MODE ON O MOTION DET gt war If you connect an alarm device to this camera you MOTION DET RETURN can monitor activity more efficiently because a signal is generated by the camera whenever motion is detected The motion detection signal is output through the MD OUT port Set up the mode using the 4 direction buttons AREA SEL You can select up to 8 PRIVACY areas AREA MODE Determines whether to use the area selected in the AREA SEL and the size and position of the AREA SETUP When the SPECIAL menu screen is displayed press the Up and Down buttons so that the arrow indicates MOTION DET Set up the mode using the 4 direction buttons Press SET to Return
18. bining Auto Iris lens Back Focus Control Lever Before installing a lens identify whether the lens to be installed is a C Mount or CS Mount This camera is set for a CS Mount Lens by default To install a C Mount Lens a simple modification is required e When Using a CS Mount Lens Remove the protective glass cover at the front of this product and turn the CS Mount Lens clockwise to install it And set focus of camera using Back Focus Control Lever of camera side after combining CS Mount lens 9 Notes gt Use the lens connector shown in the following figure If the dimensions of the connector are not correct it may damage the camera or the lens may not be installed firmly C Mount Lens 10mm or less CS Mount Lens 5mm or less e If the lens is too heavy the camera becomes unbalanced and there may be problems Use a lens that weighs less than 450g e When adjusting the Automatic Level Control ALC of an auto iris lens use Av mode if available If you use the Pk mode the picture brightness may change continuously J When Using a Mount Lens 1 Remove the protective glass cover at the front of this product and turn the C Mount Adapter clockwise to install it 2 Turn the C Mount lens clockwise to install it 3 Set focus of camera using Back Focus Control Lever of camera side after combining C Mount lens Connect the Video OUT port on the rear panel of the camera to a monitor CCD Came
19. e Beginning Serial NO Year of Manufacture Conformance to 89 336 EEC SAMSUNG TECHWIN CO LTD SAMSUNG TECHWIN CO LTD 42 SUNGJU DONG CHANGWON CITY KYUNGNAM KOREA 641 716 CCTV Camera SHC 735 S7090001 2008 02 01 EN 50081 1 1992 Backlight Compensation WDR 52dB BLC HLC OFF Day amp Night Color B W Auto EXT ICR Gain Control ow High O White Balance ATW AWC Manual Outdoor Indoor 1 800 K 10 500 K SENS UP frame Integration Auto Off x2 x256 Motion Detection On Off 8 programmable zones Alarm output Privacy Masking On Off 8 programmable zones 3D Noise Filter SSNRII On Off Level adjustable Digital Zoom On Off x2 x10 Digital Image Stabilization DIS On Of Camera Title 0f Sharpness On Of Flip Mirror On Of Communication RS 485 Baudrate 2400 4800 9600 19200 38400 57600bps selectable Protocol Samsung Techwin Protocol Pelco D Protocol ENVIRONMENTAL Operating Temperature Humidity 10 C 50 C 30 80 RH MECHANICAL Lens Mount C CS Mount Back Focus Adjustment Manual Dimension 65 8 W X60 6 H X101 9 D mm 65 8 W X60 6 H X115 D mm Weight 315g 535g COLOR CCD CAMERA 40 User Guide EMC Directive 89 336 EEC and 92 31 EEC EN 50130 4 1996
20. e mode is switched to Color in a normal environment but switches to B W mode when ambient illumination is low To set up the sswitching time or speed for AUTO mode press the SET button DWELLTIME You can select the duration time about changing the day night mode 5s 75 10s 20s 30s 405 60s DURATION You can select brightness of illumination about changing the day night mode Color gt BW B W Color Fast 2 5 lux 4 lux The brightness of illumination is changeable Slow 0 8 lux 6 lux by installed environment EXTERN This mode allows you to apply a desired filter to external signals par e When using a Video Auto Iris Lens if you set the lens level to low automatic switching between Color and Black amp White may not occur You cannot control the DAY NIGHT menu when in the EXPOSURE menu is OFF At this time the exchange between DAY mode and NIGHT mode operates as like selecting COLOR mode e Since the camera may not focus as well under infrared illumination at night as it does under normal illumination install an Extra low Dispersion Lens to obtain sharp pictures 1 When the SETUP menu screen is displayed select IMAGE ADJ by using the Up and Down buttons so that the arrow indicates IMAGE ADJ gt 7 IMAGE ADJ 2 Select a desired mode using the Up and Down buttons Bi FREEZE OFF FREEZE You can view still
21. he WDR Brightness by controlling the bar from 1 to 100 Press SET to Return COLOR CCD CAMERA 27 User Guide HLC High Light Compensation If the scene contains extremely bright light areas such as from car headlight the light can mask out much of the on screen detail DAY In normal daylight conditions the HLC is not activated NIGHT If a high light that is larger than a certain size is present on the screen HLC is activated to remove the high light HLC Enable a user to select a mask color of high light area from a picture Press SET to Return OFF Not being used 3 Select a desired mode using the Left and Right buttons and press the SET button In WDR mode shutter mode be selected fixed or flikerless A FLK e Since the following symptoms may occur according to the ambient illumination when WDR is selected set it to OFF Color or screen changes unnaturally Noise appears in the bright part of the screen Notes N Since the performance of the WDR function may be affected by the area of the bright part of the screen optimize the installation angle for the best WDR performance e If you increase LIMIT the screen display may be distorted Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen optimize the installation angle for the best HLC performance e Ina dark environment the HLC is only activated when a h
22. igh light that is larger than a certain area is present The HLC is not activated in light or overly dark conditions lt This function reduces the background noise in a low luminance environment 1 When the SETUP menu screen is displayed select SSNR by using the Up and Down buttons so that the arrow indicates SSNR gt 5 58HE 2 Select a desired mode using the Left and Right buttons O OFF Deactivates SSNR so that noise is not reduced ON Activates SSNR so that noise is reduced 3 Set the SSNR mode to ON and press the SET button Then you can adjust the noise reduction level e You cannot set the SSNR to ON or OFF when the AGC mode of the EXPOSURE menu is OFF e When adjusting the noise reduction level of the SSNR mode remember that the higher the level set the more the noise level will be reduced but that after image may also occur You can display pictures in color or black and white 1 When the SETUP menu screen is displayed select DAY NIGHT by using the Up and Down buttons so that the arrow indicates DAY NIGHT p gt DRY NIGHT AUTO 2 Select a desired mode using the Left and Right buttons according to the picture display you want COLOR The picture is always displayed in color B W The picture is always displayed in black and white Please press SETUP button to turn on or off the burst signal on B W mode AUTO Th
23. ignals are output through this port Connect this port to the Video IN port of a monitor Power LED When power is properly connected this LED comes on Power IN Port Connect the power as specified for each model here The lens is not supplied with this camera Purchase a lens suitable for your environment This camera accepts the auto iris lens and both C and CS mount lens e It is recommended to use the DC type Auto Iris Lens to effectively enjoy the major functions of this camera e Keep the lens surface clean since if it is contaminated with dirt or fingerprints the picture quality suffers 1 Strip the insulation of the auto iris lens cable 8mm from the end approx 8mm 2 Strip the insulation of the core of the auto iris lens cable to expose a 2mm length approx 2m 3 Remove the cover of the auto iris lens connector plug and solder the lens cable to the connector pin of the plug e For a Video Drive Lens For aDC Drive Lens Pin 1 Red Power Pin 1 Damping Pin 2 NC Pin 2 Damping Pin 3 White Video Signal Pin 3 Drive Pin 4 Black Ground Pin 4 Drive Lens cable No 3 Pin t connector No 1 Pin No 4 Pin No 2 Pin 4 Fit the cover of the auto iris lens connector plug remove the protective glass cover from the front of the camera and fasten the auto iris lens by turning it clockwise 5 Set focus of camera using Back Focus Control Lever of camera side after com
24. on of 560 TV lines for color and 700 TV lines for B W Wide Dynamic Range WDR By adopting a proprietary SV IV DSP chip the camera delivers clear high quality pictures even in backlight by increasing exposure in dark areas while decreasing it in bright areas a corrected image with clear details results Excellent Sensitivity Adopting a Diagonal 6mm 1 3 highly sensitive CCD and digital signal processing technology it can clearly distinguish the outline and color of a subject in an extremely low luminance environment even for example under starlight Since surveillance is possible in places where the light is poor the camera is appropriate for day and night surveillance outdoors or on the outside of buildings 0 001 Lux Color Sens up Mode 0 00004 Lux B W Sens up Mode SSNR Samsung Super Noise Reduction Function The high performance SV IV DSP chip dramatically reduces the gain noise in digital image processing producing clear sharp images in low lighting environments Day amp Night The camera identifies whether it is day or night and automatically switches to the appropriate mode depending on its environment By day the camera switches to color mode in order to maintain optimal color At night it switches to B W mode so as to obtain better picture definition Motion Detection Since the camera detects motion and generates signals without any additional external sensors you can monitor activity m
25. or moving pictures OV REV You can flip the picture vertically on the screen H REV You can flip the picture horizontally on the screen D Z00M You can use a digital zoom of x1 x10 Press SET to Return SHARPNESS As you increase this value the picture outline becomes stronger and clearer Adjust this value appropriately depending on the sharpness of the picture Press SET to Return PED LEVEL Please use this menu item when using a LCD monitor other than standard ones You can change PED LEVEL RETURN Select this to save the settings for the IMAGE ADJ menu and to return to the SETUP menu Notes e When the V REV or H REV mode is enabled the text on the screen does not flip If you increase the SHARPNESS level too high the picture may become distorted or noise may appear 1 When the SETUP menu screen is displayed select SPECIAL by using the Up and Down buttons so that the arrow indicates SPECIAL b E SPECIAL 2 Select a desired mode using the Up and Down buttons gt i CAM TITLE OFF CAMTITLE If you enter a title the title will appear on the monitor O If the SPECIAL menu screen is displayed use the Up and Down buttons so that the arrow indicates CAM TITLE Set it to ON by using the Left and Right buttons Notes e When the CAM TITLE menu is OFF no title will be displayed on the monitor screen bi CAM TITLE even if you enter
26. ore efficiently by connecting the camera to an alarm device DIS Digital Image Stabilizer The DIS function compensates for any camera movement to produce more stable pictures Video DC Drive Lens Support You can select Video or DC Drive Lens from the menu Miscellaneous Functions HCL HIGH LIGHT COMPENSATION SYNC INT LL SENS UP FREEZE FLIP H V REV D Z00M SHARPNESS MOTION DETECTION and PRIVACY functions are provided RS 485 Communication Control Support Remote OSD menu control via an RS 485 interface is supported 080 The camera control is convenient by using 9 different foreign language 0 5 0 NTSC KOREAN ENGLISH JAPANESE SPANISH FRENCH PORTUGUESE PAL ENGLISH FRENCH GERMAN SPANISH ITALIAN CHINESE PORTUGUESE COLOR CCD CAMERA 6 User Guide Samsung Techwin cares for the environment at all product manufacturing stages to preserve the environment and is taking a number of steps to provide NIA customers with more environment friendly products The Eco mark represents Samsung Techwin s will to create environment friendly products and indicates ROHS compliant that the product satisfies the EU RoHS Directive QO Warnings amp Cautions This information is provided to ensure your safety and to prevent any losses financial or otherwise Please read it carefully and use the product accordingly For product inquiries please contact the retail shop where you bought the camera
27. ra 4 Monitor Y Since the connection procedure may differ depending on the type of monitor or peripheral device to be connected refer to the User Manual for the device to be connected e Make sure to turn off the device to be connected before making any connections Turn the 75Q Hi Z switches of interim display devices to the Hi Z position and the switches of any final device to the 750 position Intermediate End monitor CCD Camera Since power specifications differ depending on the model make sure to check your model name and specifications before connecting power You can connect power as shown in the following figure Since the power specification supports both AC and DC connect AC 24V 500mA Adaptor or DC 12V 500mA Adaptor e Use AC230V 50Hz power source For SHC 735PH Installation Procedures _ When the resistance value of copper wire is at 20 68 Copper wire size AWG 24 0 22mm2 22 0 33 2 20 0 52 2 18 0 83mm2 Resistance value Q m 0 078 0 050 0 030 0 018 Voltage drop V m 0 028 0 018 0 011 0 006 J How to Use the Camera Function Menu Structure e As shown in the table above voltage decreases as the wire gets longer Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera Standard voltage for camera operation DC 12V 10 24V 10
28. should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal COLOR CCD CAMERA D User Guide A NO 7 SR Use only under temperature conditions May lower image quality between 10 C and 50 C Provide good ventilation when using in high temperature conditions Severe lighting changes or flickering may The lens is the most important component hinder normal camera operation of the camera Be careful not to smear it with fingerprints May cause a product malfunction We A 2 Wipe dry any liquids Liquids may contain Radioactivity exposure may damage the minerals that are corrosive to electronic CCD components Notes e Exposure to a spotlight or an object emitting strong light may cause smear or blooming e Ensure that the power source complies with normal specifications before supplying it to the camera 1 Ultra High Resolution WDR Color CCD Camera SHC 735 2 Auto Iris Lens Connector Plug 3 C Mount Adapter NAA ALAPAN AR TARA N Tripod Mounting Bracket Screw Hole Used to fix the Tripod Mounting Bracket to the top of the camera C Mount Lens Adapter Install this adapter to use a C Mount Lens Back Focus Control Lever Adjust focus by this Back Focus Lever 4 Instruction Manual SAMSUNG SHC 735 www samsungcctv
Download Pdf Manuals
Related Search