Sony MEX-DV1700U Installation/Connections Manual
Contents
1. Connecting the parking brake cord Be sure to connect the parking cord Light green of to the parking brake switch cord The mounting position of the parking brake switch cord depends on your car Consult your car dealer or your nearest Sony dealer for further details Removing the protection collar and the bracket Before installing the unit remove the protection collar and the bracket Q from the unit 1 Remove the protection collar Pinch both edges of the protection collar then pull it out 2 Remove the bracket Q Insert both release keys together between the unit and the bracket Q until they click Pull down the bracket then pull up the unit to separate Mounting example 6 Installation in the dashboard Notes Bend these claws outward for a tight fit if necessary 2 Make sure that the 4 catches on the protection collar 4 are properly engaged in the slots of the unit 3 Mounting the unitina Japanese car 7 You may not be able to install this unit in some makes of Japanese cars In such a case consult your Sony dealer Note To prevent malfunction install only with the supplied screws p Front panel release button S How to detach and attach the front panel Before installing the unit detach the front panel EJ A To detach Before detaching the front panel be sure to press and hold SOURCE OFF Press the front panel rel2. see Notes on the control and power supply leads O To the 12 V power terminal which is energized at all times Be sure to connect the black ground earth lead to a metal surface of the car first Oto the parking brake switch cord Notes on the control and power supply leads REM OUT lead blue white striped supplies 12 VDC when you turn on the unit When your car has built in FM AM antenna aerial in the rear side glass connect REM OUT lead blue white striped or the accessory power supply lead red to the power terminal of the existing antenna aerial booster For details consult your dealer e A power antenna aerial without a relay box cannot be used with this unit Memory hold connection When the yellow power supply lead is connected power will always be supplied to the memory circuit even when the ignition switch is turned off Notes on speaker connection Before connecting the speakers turn the unit off Use speakers with an impedance of 4 to 8 ohms and with adequate power handling capacities to avoid its damage Do not connect the speaker terminals to the car chassis or connect the terminals of the right speakers with those of the left speaker Do not connect the ground earth lead of this unit to the negative terminal of the speaker Do not attempt to connect the speakers in parallel Connect only passive speakers Connecting active speakers with built in amplifiers to the s
3. SONY 4 296 932 11 1 Multi Disc Player Installation Connections MEX DV1707U MEX DV1700U Equipment used in illustrations not supplied Front speaker 1 42969321 1 2011 Sony Corporation Printed in Thailand except for U S models Subwoofer Rear speaker Power amplifier http www sony net AUDIO OUT Monitor not supplied REAR SUB AUDIO OUT Monitor not supplied REAR SUB AUDIO OUT 2 REM OUT Max supply current 0 4 A from car antenna aerial Satellite radio tuner SiriusXM not supplied RCA pin cord not supplied AUDIO OUT can be switched SUB or REAR For details see the supplied Operating Instructions Auxiliary device such as hideaway navigation device TV tuner box etc Separate adaptor may be required U S models only For details on connecting to the parking brake switch cord see Connecting the parking brake cord Z on the reverse side Satellite radio tuner SiriusXM gt FRONT AUDIO OUT AUX AUDIO IN SIRIUSXM VIDEO OUT Fuse 10 A Bike Blue white striped White black striped Orange white striped ILLUMINATION gt Q Gray black striped Green black striped Light green PARKING BRAKE Purple black striped e This unit is designed for negative ground earth 12 V DC operation only Do not get the
4. are straight or bent outwards the unit will not be installed securely and may spring out Connection example 2 Notes H A Be sure to connect the ground earth lead before connecting the amplifier e The alarm will only sound if the built in amplifier is used 1 To a metal surface of the car First connect the black ground earth lead then connect the yellow and red power supply leads 2 To the power antenna aerial control lead or power supply lead of antenna aerial booster Notes Itis not necessary to connect this lead if there is no power antenna aerial or antenna aerial booster or witha manually operated telescopic antenna aerial When your car has a built in FM AM antenna aerial in the rear side glass see Notes on the control and power supply leads To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers Connecting any other system may damage the unit To a car s illumination signal Be sure to connect the black ground earth lead to a metal surface of the car first To the 12 V power terminal which is energized in the accessory position of the ignition switch Notes e Ifthere is no accessory position connect to the 12 V power battery terminal which is energized at all times Be sure to connect the black ground earth lead to a metal surface of the car first When your car has a built in FM AM antenna aerial in the rear side glass
5. ease button and pull it off towards you EJ B To attach Engage part of the front panel with part of the unit as illustrated and push the left side into position until it clicks Warning if your car s ignition has no ACC position Be sure to set the Auto Off function For details see the supplied Operating Instructions The unit will shut off completely and automatically in the set time after the unit is turned off which prevents battery drain If you do not set the Auto Off function press and hold until the display disappears each time you turn the ignition off Fuse replacement When replacing the fuse be sure to use one matching the amperage rating stated on the original fuse If the fuse blows check the power connection and replace the fuse If the fuse blows again after S replacement there may be an Ses internal malfunction In such a case N consult your nearest Sony dealer N Fuse 10 A
6. leads under a screw or caught in moving parts e g seat railing Before making connections turn the car ignition off to avoid short circuits Connect the yellow and red power supply leads only after all other leads have been connected e Run all ground earth leads to a common ground earth point Be sure to insulate any loose unconnected leads with electrical tape for safety The use of optical instruments with this product will increase eye hazard Notes on the power supply lead yellow When connecting this unit in combination with other stereo components the connected car circuit s rating must be higher than the sum of each component s fuse When no car circuits are rated high enough connect the unit directly to the battery Parts list 1 The numbers in the list are keyed to those in the instructions The bracket and the protection collar are attached to the unit before shipping Before mounting the unit use the release keys to remove the bracket from the unit For details see Removing the protection collar and the bracket Eq on the reverse side of the sheet e Keep the release keys for future use as they are also necessary if you remove the unit from your car Caution Handle the bracket Q carefully to avoid injuring your fingers Note Before installing make sure that the catches on both sides of the bracket are bent inwards 2 mm 3 2 in If the catches
7. peaker terminals may damage the unit To avoid a malfunction do not use the built in speaker leads installed in your car if the unit shares a common negative lead for the right and left speakers Do not connect the unit s speaker leads to each other Notes on connection If speaker and amplifier are not connected correctly FAILURE appears in the display In this case make sure the speaker and amplifier are connected correctly e Ifyou are to use the monitor for the rear seats connect the parking brake switch cord to the ground earth 7A A toyota size 5 x max 8 mm 7 32 x max 5 16 in Bracket Existing parts supplied with your car Foot brake type Hand brake type ES Parking brake switch cord Parking brake switch cord B nissan size 5 x max 8 mm 7 32 x max 5 16 in size Bracket 5 x max 8 mm 7 32 x max 5 16 in Bracket Existing parts supplied with your car Dashboard size 5 x max 8 mm 7 32 x max 5 16 in Bracket SOURCE OFF Precautions Choose the installation location carefully so that the unit will not interfere with normal driving operations Avoid installing the unit in areas subject to dust dirt excessive vibration or high temperatures such as in direct sunlight or near heater ducts Use only the supplied mounting hardware for a safe and secure installation Mounting angle adjustment Adjust the mounting angle to less than 45
Download Pdf Manuals
Related Search