Sony HKJ-101 User's Manual
Contents
1. 4 Fix the DV 29 board to the IF panel and to the CN 2478 board using the supplied screws PWH2 X 5 2 screws PSW2 6 X 5 3 screws When tightening the screws tighten the screws PWH2 X 5 first of all screws Install the supplied rear panel for J H1 using the six M3 case stopper screws Tighten the screws in the state that the two dowels are aligned with the holes a and b on the rear panel as shown in the figure DV 29 board PSW2 6 x 5 Psw2 x 5 CN 2478 board Dowel M3 case stopper a screws M3 case stopper screws J H1 rear panel Supplied accessory 1 2 E HKJ 101 1 2 2 To install HKJ 101 in J H3 1 Remove the six M3 case stopper screws 2 Remove the rear panel Store the removed rear panel in a safe place so as not to lose it Ost X M3 case stopper TR screws zh M3 case stopper screws Insert the connector CN601 on the DV 29 board into the connector CN41 on the SDI 80 assembly First insert the connector CN401 on the DV 29 board to the hole for i LINK connector on the IF panel Then insert connector CN601 to the connector on the CN 2478 board Fix the DV 29 board to the IF panel and to the SDI 80 assembly using the supplied screws PWH2 x 5 2 screws PSW2 6 x 5 3 screws When tightening the screws tighten the screws PWH2 X 5 first of all screws 3 Pull out the SDI 80 assembly from the second slot from the botto2. partie que ce soit de ce manuel ou son emploi pour tout autre but que des op rations ou entretiens de l quipement moins d une permission crite de Sony Corporation Das in dieser Anleitung enthaltene Material besteht aus Informationen die Eigentum der Sony Corporation sind Die Sony Corporation untersagt ausdr cklich die Vervielf ltigung jeglicher Teile dieser Anleitung oder den Gebrauch derselben f r irgendeinen anderen Zweck als die Bedienung oder Wartung der in dieser Anleitung beschriebenen Ausr stung ohne ausdr ckliche schriftliche Erlaubnis der Sony Corporation HKJ 101 Printed in Japan HKJ 101 SY J E Sony Corporation 2003 7 16 3 805 991 01 B amp P Company 2003
3. SONY i LINK INTERFACE BOARD HKJ 101 1 INSTALLATION MANUAL 1st Edition ABS ZOVIaAy ls U EAHATCT DANA ZONZAI NARSNEREPRTF MR HERES CMB RKE AFFBUCDEMATEMHBOVET fae SIZED FEA RL VF ESUERMNBOATCHAXK FSW Z WARNING This manual is intended for qualified service personnel only To reduce the risk of electric shock fire or injury do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so Refer all servicing to qualified service personnel ANWARNUNG Die Anleitung ist nur f r qualifiziertes Fachpersonal bestimmt Alle Wartungsarbeiten d rfen nur von qualifiziertem Fachpersonal ausgef hrt werden Um die Gefahr eines elektrischen Schlages Feuergefahr und Verletzungen zu vermeiden sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen Andere als die angegeben Wartungsarbeiten d rfen nur von Personen ausgef hrt werden die eine spezielle Bef higung dazu besitzen A AVERTISSEMENT Ce manual est destin uniquement aux personnes comp tentes en charge de l entretien Afin de r duire les risques de d charge lectrique d incendie ou de blessure n effectuer que les r parations indiqu es dans le mode d emploi moins d tre qualifi pour en effectuer d autres Pour toute r paration faire appel une personne comp tente uniquement i LINK 214 IEEE 1394 1995 ERB KOZ OSRORLEER RL VOOR c amp IXLLINKO IP TY i LINK an
4. This Class A digital apparatus complies with Canadian ICES 003 Pour les utilisateurs au Canada Cet appareil num rique de la classe A est conforme a la norme NMB 003 du Canada HKJ 101 For the customers in Europe This product with the CE marking complies with the EMC Directive 89 336 EEC issued by the Commission of the European Community Compliance with this directive implies conformity to the following European standards EN55103 1 Electromagnetic Interference Emission EN55103 2 Electromagnetic Susceptibility Immunity This product is intended for use in the following Electromagnetic Environment E1 residential E2 commercial and light industrial E3 urban outdoors and E4 controlled EMC environment ex TV studio Pour les clients europ ens Ce produit portant la marque CE est conforme la Directive sur la compatibilit lectromagn tique EMC 89 336 CEE mise par la Commission de la Communaut Europ enne La conformit cette directive implique la conformit aux normes europ ennes suivantes EN55103 1 Interf rences lectromagn tiques mission EN55103 2 Sensibilit lectromagn tique immunit Ce produit est pr vu pour tre utilis dans l environnement lectromagn tique suivant E1 r sidentiel E2 commercial et industrie l g re E3 urbain ext rieur et E4 environnement EMC contr l ex studio de t l vision F r Kunden in Europa Dieses Produ
5. d are trademarks and indicate that this product is in agreement with IEEE 1394 1995 specifications and their revisions HKJ 101 For the customers in the USA This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment The shielded interface cable recommended in this manual must be used with this equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules The device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including ineterference that may cause undesired operation For customers in Canada
6. kt besitzt die CE Kennzeichnung Und erf llt die EMV Richtlinie 89 336 EWG EG Kommission Angewandte Normen EN55103 1 Elektromagnetische Vertr glichkeit St raussendung EN55103 2 Elektromagnetische Vertr glichkeit St rfestigkeit f r die folgenden elektromagnetischen Umgebungen E1 Wohnbereich E2 kommerzieller und in beschr nktem Ma e industrieller Bereich E3 Stadtbereich im Freien und E4 kontrollierter EMV Bereich z B Fernsehstudio Section 1 Installation 1 1 Overview The LINK interface board HKJ 101 enables the Digital Video Cassette Compact Player J H1 J H3 to output the down converted SD video signal in the i LINK DV format In addition off line editing can be executed by connecting the J H1 J H3 containing the HKJ 101 board to the PC containing the non linear editing software using an i LINK DV cable HKJ 101 consists of the followings DV 29 board 1 CN 2478 board 1 Rear panel for J H1 1 Rear panel for J H3 1 Beside this Installation Manual the following manuals are prepared for HKJ 101 Operation Manual CD ROM Supplied with J H1 J H3 This manual is necessary for practical application and operation of J H1 J H3 and HKJ 101 Operation Guide Supplied with J H1 J H3 This manual serves as a quick reference J H Series Maintenance Manual e manual Available on request This manual describes the information that premises the component service periodic inspec
7. m of the J H3 in the direction of the arrow PSW2 6 x 5 amp Psw2 6 x5 SDI 80 assembly Insert the SDI 80 assembly to the original slot Strongly push the connector panel both from the right and the left sides of the SDI 80 assembly so that the connector on the SDI 80 assembly is securely inserted into the connector on the MB 993 board HKJ 101 1 3 E 8 Install the supplied rear panel for J H3 using the six M3 case stopper screws Tighten the screws in the state that the two dowels are aligned with the holes a and b on the rear panel as shown in the figure M3 case stopper screws p Hole a M3 case stopper 4J H3 rear panel screws Supplied accessory 1 4 E HKJ 101 ZOY 17 WIA S VCS HD 8f 9 3 EIS HIET GET MORIZ Lice CHS LEO MANR EHE PROFS CRRAZBNWCAV IA IVER TS CeEPRIELET The material contained in this manual consists of information that is the property of Sony Corporation Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation Le mat riel contenu dans ce manuel consiste en informations qui sont la propri t de Sony Corporation Sony Corporation interdit formellement la copie de quelque
8. tion periodic maintenance diagnostics parts replacement adjustments parts list block diagrams schematic diagrams board layouts and others to be used by system and maintenance engineers If this manual required please contact your local Sony Sales Office Service Center 1 2 Installing the Circuit Board Procedure is different when installing HKJ 101 in J H1 and J H3 To install HKJ 101 in J H1 Refer to Section 1 2 1 To install HKJ 101 in J H3 Refer to Section 1 2 2 Before starting installation be sure to turn off the POWER switch and disconnect the power cord Then start the following procedures HKJ 101 1 1 E 1 2 1 To install HKJ 101 in J H1 1 Remove the six M3 case stopper screws 2 Remove the rear panel Store the removed rear panel in a safe place so as not to lose it Insert the CN 2478 board to the second slot from the bottom of J H1 Strongly push the connector panel both from the right and the left sides of the CN 2478 board so that the connector on the CN 2478 board is securely inserted into the connector on the MB 993 board ee A M3 case stopper w screws we M3 case stopper screws 3 Insert the connector CN601 on the DV 29 board into the connector CN41 on the CN 2478 board First insert the connector CN401 on the DV 29 board to the hole for i LINK connector on the IF panel Then insert connector CN601 to the connector on the CN 2478 board
Download Pdf Manuals
Related Search