Home
Sony CDX-GT72W Installation/Connections Manual
Contents
1. Make sure that the 4 catches on the protection collar 4 are properly engaged in the slots of the unit EJ 3 Mounting the unit in a Japanese Car You may not be able to install this unit in some makes of Japanese cars In such a case consult your Sony dealer Notes Install only with the supplied screws or the front panel may not slide correctly Do not use holes not specific for the task and do not install screws longer than 8 mm 1 s2 in T Toyota Cars N Nissan Cars 8mm 11 32 in How to detach and attach the front panel Before installing the unit detach the front panel KA A To detach Before detaching the front panel be sure to press COFF Press M then slide the front panel to the left and gently pull out the front panel towards you 4 8 To attach Place the hole of the front panel onto the spindle on the unit then lightly push the left side in Warning if your car s ignition has no ACC position Be sure to set the Auto Off function For details see the supplied Operating Instructions The unit will shut off completely and automatically in the set time after the unit is turned off which prevents battery drain Tf you do not set the Auto Off function press and hold until the display disappears each time you turn the ignition off RESET button When the installation and connections are completed be sure to press the RESET button with
2. not necessary to connect this lead if there is no power antenna aerial or antenna aerial booster or with a manually operated telescopic antenna aerial When your car has a built in FM AM antenna aerial in the rear side glass see Notes on the control and power supply leads To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers Connecting any other system may damage the unit O To the interface cable of a car telephone O Toa car s illumination signal Be sure to connect the black ground earth lead to a metal surface of the car first O To the 12 V power terminal which is energized in the accessory position of the ignition switch Notes e If there is no accessory position connect to the 12 V power battery terminal which is energized at all times Be sure to connect the black ground earth lead to a metal surface of the car first When your car has a built in FM AM antenna aerial in the rear side glass see Notes on the control and power supply leads O To the 12 V power terminal which is energized at all times Be sure to connect the black ground earth lead to a metal surface of the car first BUS AUDIO IN 1 SUB OUT MONO from car antenna aerial desde la antena del autom vil AMP REM Max supply current 0 3 A Fuse 10 A NUDE Fusibile 10 A REAR o 4 Blue white striped Con rayas azules y blancas Corriente m x de alimentac
3. 2 V que recibe energ a sin interrupci n Aseg rese de conectar primero el cable de conexi n a masa negro a una superficie met lica del autom vil circuito de la memoria recibir siempre alimentaci n aunque apague el interruptor de encendido Notas sobre la conexi n de los altavoces Antes de conectar los altavoces desconecte la alimentaci n de la unidad Utilice altavoces con una impedancia de 4 a8 Q con la capacidad de potencia adecuada para evitar que se da en No conecte los terminales de altavoz al chasis del autom vil ni conecte los terminales del altavoz derecho con los del izquierdo No conecte el cable de conexi n a masa de esta unidad al terminal negativo del altavoz No intente conectar los altavoces en paralelo Conecte solamente altavoces pasivos Si conecta altavoces activos con amplificadores incorporados a los terminales de altavoz puede da ar la unidad Para evitar fallas de funcionamiento no utilice los cables de altavoz incorporados instalados en el autom vil si la unidad comparte un cable negativo com n para los altavoces derecho e izquierdo No conecte los cables de altavoz de la unidad entre s Nota sobre la conexi n Si el altavoz y el amplificador no est n conectados correctamente aparecer FAILURE en la pantalla Si es as compruebe la conexi n del altavoz y el amplificador E A tovora max size 5x8mm 7 32 x 11 32 in Tama o m x 5x8mm Bracket Sopo
4. SONY FM AM Compact Disc Player 3 283 551 31 1 Installation Connections Instalaci n Conexiones CDX GT72W O 2008 Sony Corporation Printed in Thailand Equipment used in illustrations not supplied Equipo utilizado en las ilustraciones no suministrado Front speaker Altavoz frontal Rear speaker Altavoz posterior Active subwoofer Altavoz potenciador de graves activo Ro E Power amplifier Altavoz potenciador de graves activo CD MD changer Cambiador de CD MD Rotary commander RM X4S Mando rotatorio RM X4S SUB OUT MONO BUS AUDIO IN A Ei E k AUDIO OUT FRONT ALS BUS CONTROL IN BUS AUDIO IN Source selector Selector de fuente XA C40 BUS CONTROL IN e This unit is designed for negative ground earth 12 V DC operation only e Do not get the leads under a screw or caught in moving parts e g seat railing e Before making connections turn the car ignition off to avoid short circuits e Connect the yellow and red power supply leads only after all other leads have been connected Run all ground earth leads to a common ground earth point e Be sure to insulate any loose unconnected leads with electrical tape for safety The use of optical instruments with this product will increase eye hazard Notes on the power supply lead yellow When connecting this unit in combination with other stereo components the connected car circuit s rating m
5. a ball point pen etc after detaching the front panel Precauciones e Elija cuidadosamente el lugar de montaje de forma que la unidad no interfiera con las funciones normales de manejo e Evite instalar la unidad donde pueda quedar sometida a polvo suciedad vibraciones excesivas o altas temperaturas como por ejemplo a la luz solar directa o cerca de conductos de calefacci n e Para realizar una instalaci n segura y firme utilice solamente elementos de instalaci n suministrados Ajuste del ngulo de montaje Ajuste el ngulo de montaje a menos de 45 Extracci n del soporte 4 Antes de instalar la unidad retire el soporte Y de esta 1 Inserte ambas llaves de liberaci n entre la unidad y el soporte Q hasta que encajen 2 Presione el soporte y a continuaci n levante la unidad para separar ambos elementos Ejemplo de montaje Instalaci n en el tablero Notas e Si es necesario doble estos ganchos hacia fuera para que encaje firmemente EJ 2 Compruebe que los 4 enganches del marco de protecci n 4 est n bien fijados en las ranuras de la unidad E 3 Montaje de la unidad en un autom vil japon s Es posible que no pueda instalar esta unidad en algunos autom viles japoneses En tal caso consulte a su distribuidor Sony Notas Para que el panel frontal se deslice correctamente realice la instalaci n solamente con los tornillos suministrado
6. e entrada de alimentaci n O Al cable de control de la antena motorizada o al cable de fuente de alimentaci n del amplificador de se al de la antena Notas e Sino se dispone de antena motorizada ni de amplificador de antena o se utiliza una antena telesc pica accionada manualmente no ser necesario conectar este cable e Si el autom vil incorpora una antena de FM AM en el cristal trasero o lateral consulte Notas sobre los cables de control y de fuente de alimentaci n A AMP REMOTE IN de un amplificador de potencia opcional Esta conexi n es s lo para amplificadores La conexi n de cualquier otro sistema puede da ar la unidad O Al cable de interfaz de un tel fono para autom vil 0 A una se al de iluminaci n del autom vil Aseg rese de conectar primero el cable de conexi n a masa negro a una superficie met lica del autom vil O Al terminal de alimentaci n de 12 V que recibe energ a en la posici n de accesorio del interruptor de la llave de encendido Notas e Sino hay posici n de accesorio con ctelo al terminal de alimentaci n bater a de 12 V que recibe energ a sin interrupci n Aseg rese de conectar primero el cable de conexi n a masa negro a una superficie met lica del autom vil e Si el autom vil incorpora una antena de FM AM en el cristal trasero o lateral consulte Notas sobre los cables de control y de fuente de alimentaci n O Al terminal de alimentaci n de 1
7. i n de 0 3 A Izquierdo Right Derecho Izquierdo Right Derecho Notes on the control and power supply leads The power antenna aerial control lead blue supplies 12 V DC when you turn on the tuner When your car has built in FM AM antenna aerial in the rear side glass connect the power antenna aerial control lead blue or the accessory power supply lead red to the power terminal of the existing antenna aerial booster For details consult your dealer A power antenna aerial without a relay box cannot be used with this unit Memory hold connection When the yellow power supply lead is connected power will always be supplied to the memory circuit even when the ignition switch is turned off Notes on speaker connection Before connecting the speakers turn the unit off Use speakers with an impedance of 4 to 8 ohms and with adequate power handling capacities to avoid its damage Do not connect the speaker terminals to the car chassis or connect the terminals of the right speakers with those of the left speaker Do not connect the ground earth lead of this unit to the negative terminal of the speaker Do not attempt to connect the speakers in parallel Connect only passive speakers Connecting active speakers with built in amplifiers to the speaker terminals may damage the unit To avoid a malfunction do not use the built in speaker leads installed in your car if the uni
8. l cable de conexi n a masa antes de realizar la conexi n del amplificador La alarma sonar nicamente si se utiliza el amplificador incorporado Sugerencia P B O Si desea conectar dos o m s cambiadores de CD MD necesitar el selector de fuente XA C40 no suministrado Supplied with the CD MD changer Suministrado con el cambiador de CD MD E 1 RCA pin cord not supplied 2 Supplied with XA C40 3 Insert with the cord upwards 1 Cable con terminales RCA no suministrado 2 Suministrado con el XA C40 3 Insertar con el cable hacia arriba Notas sobre los cables de control y de fuente de alimentaci n El cable de control de la antena motorizada azul suministrar cc de 12 V cuando conecte la alimentaci n del sintonizador Si el autom vil dispone de una antena de FM AM incorporada en el cristal trasero o lateral conecte el cable de control de antena motorizada azul o el cable de entrada de alimentaci n auxiliar rojo al terminal de alimentaci n del amplificador de antena existente Para obtener m s informaci n consulte a su distribuidor Con esta unidad no es posible utilizar una antena motorizada sin caja de rel Conexi n para protecci n de la memoria Si conecta el cable de entrada de alimentaci n amarillo el Diagrama de conexi n O A una superficie met lica del autom vil Conecte primero el cable de conexi n a masa negro y despu s los cables amarillo y rojo d
9. rcuito conectado del autom vil debe ser superior a la suma del fusible de cada componente e Si no hay circuitos del autom vil con capacidad nominal suficientemente alta conecte la unidad directamente a la bater a Lista de componentes e Los n meros de la lista corresponden a los de las instrucciones e La unidad se comercializa con el soporte Q Antes de montarla utilice las llaves de liberaci n para extraer el soporte 1 de la unidad Para obtener m s informaci n consulte Extracci n del soporte EJ en el dorso de la hoja Conserve las llaves de liberaci n G para utilizarlas en el futuro ya que tambi n las necesitar si retira la unidad del autom vil Precauci n Tenga mucho cuidado al manipular el soporte Q para evitar posibles lesiones en los dedos Enganche Nota Antes de instalar la unidad compruebe que los enganches de ambos lados del soporte 1 est n doblados hacia adentro 2 mm Si no lo est n o est n doblados hacia afuera la unidad no se instalar correctamente y puede saltar Source selector not supplied Selector de fuente no suministrado d CONTROL IN gt Q ANT REM gt Max supply current 0 1 A Corriente m x de alimentaci n de 0 1 A Light blue Azul celeste ATT 0 Orange white striped Con rayas naranjas y blancas ILLUMINATION Q Yellow Amarillo EO S EN Notas A s Aseg rese de conectar primero e
10. rte Face the hook inwards El gancho debe encontrarse en la parte interior to dashboard center console Bracket Soporte Existing parts supplied with your car Piezas existentes suministradas con su autom vil max size 5x8mm 7 32 x 11 32 in Tama o m x 5x8mm B Nissan max size 5 x 8 mm 7h2 x 11 32 in Tama o m x 5 x 8 mm Dashboard Tablero to dashboard center console al tablero o consola central G PS Q y Bracket Soporte ES max size x y 5x8 mm 7 32 x 11 32 in Tama o m x 5x8mm Existing parts supplied with your car Piezas existentes suministradas con su autom vil Precautions e Choose the installation location carefully so that the unit will not interfere with normal driving operations e Avoid installing the unit in areas subject to dust dirt excessive vibration or high temperatures such as in direct sunlight or near heater ducts e Use only the supplied mounting hardware for a safe and secure installation Mounting angle adjustment Adjust the mounting angle to less than 45 Removing the bracket Before installing the unit remove the bracket from the unit 1 Insert both release keys together between the unit and the bracket Q until they click 2 Pull down the bracket then pull up the unit to separate Mounting example Installation in the dashboard Notes Bend these claws outward for a tight fit if necessary BJ 2
11. s No utilice orificios que no est n destinados espec ficamente a esta tarea y no instale tornillos de m s de 8 mm de longitud T Coches Toyota N Coches Nissan Extracci n e instalaci n del panel frontal Antes de instalar la unidad extraiga el panel frontal A A Para extraerlo Antes de extraer el panel frontal aseg rese de presionar OF Presione f y a continuaci n deslice el panel frontal hacia la izquierda y tire suavemente de l hacia usted 4 B Para instalarlo Coloque el orificio A del panel frontal en el eje 8 de la unidad y a continuaci n presione ligeramente el lado izquierdo hacia adentro Advertencia si el encendido del autom vil no dispone de una posici n ACC Aseg rese de ajustar la funci n de desconexi n autom tica Para obtener m s informaci n consulte el manual de instrucciones suministrado La unidad se apagar completa y autom ticamente en el tiempo establecido despu s de que se desconecte la unidad lo que evita que se desgaste la bater a Si no ajust la funci n de desconexi n autom tica mantenga presionado cada vez que apague el interruptor de encendido hasta que la pantalla desaparezca Bot n RESET Una vez finalizada la instalaci n y las conexiones desmonte el panel frontal y presione el bot n RESET con un bol grafo o un objeto similar D J
12. t shares a common negative lead for the right and left speakers Do not connect the unit s speaker leads to each other Note on connection If speaker and amplifier are not connected correctly FAILURE appears in the display In this case make sure the speaker and amplifier are connected correctly White Blanco White black striped Con rayas blancas y negras Gray Gris Gray black striped Con rayas grises y negras Green Verde Green black striped Con rayas verdes y negras Purple Morado Purple black striped Con rayas moradas y negras Precauciones Esta unidad se dise para alimentarse s lo con cc de 12 V de masa negativa e No coloque los cables debajo de ning n tornillo ni los aprisione con partes m viles p ej los ra les del asiento Antes de realizar las conexiones desactive el encendido del autom vil para evitar cortocircuitos e Conecte los cables de entrada de alimentaci n amarillo y rojo solamente despu s de haber conectado los dem s e Conecte todos los cables de conexi n a masa a un punto com n e Por razones de seguridad aseg rese de aislar con cinta aislante los cables sueltos que no est n conectados El uso de instrumentos pticos con este producto aumenta el riesgo de sufrir da os oculares Notas sobre el cable de fuente de alimentaci n amarillo e Cuando conecte esta unidad en combinaci n con otros componentes est reo la capacidad nominal del ci
13. ust be higher than the sum of each component s fuse e When no car circuits are rated high enough connect the unit directly to the battery Parts list The numbers in the list are keyed to those in the instructions The bracket Q is attached to the unit before shipping Before mounting the unit use the release keys 8 to remove the bracket O from the unit For details see Removing the bracket E on the reverse side of the sheet Keep the release keys for future use as they are also necessary if you remove the unit from your car Caution Handle the bracket Q carefully to avoid injuring your fingers Catch Note Before installing make sure that the catches on both sides of the bracket Q are bent inwards 2 mm 3 s2 in If the catches are straight or bent outwards the unit will not be installed securely and may spring out not supplied no suministrado Connection example Notes A A Be sure to connect the ground earth lead before connecting the amplifier e The alarm will only sound if the built in amplifier is used Tip H 8 0 For connecting two or more CD MD changers the source selector XA C40 not supplied is necessary Connection diagram O To a metal surface of the car First connect the black ground earth lead then connect the yellow and red power supply leads O To the power antenna aerial control lead or power supply lead of antenna aerial booster Notes e Itis
Download Pdf Manuals
Related Search
Related Contents
ERI catalogue 2004 (bis) tapis de course motorise techness run 800 manuel d Trust GXT 280 ATOM User Manual Play - Free User`s Manual (Portuguese) Logitech M525 User's Manual Copyright © All rights reserved.
Failed to retrieve file