Sony CDX-2180 User's Manual
Contents
1. out Do not use solvents such as benzine thinner commercially available cleaners or antistatic spray intended for analog discs Note on moisture condensation On a rainy day or in a very damp area moisture may condense on the lenses inside the CD player Should this occur the unit will not operate properly In this case remove the disc and wait for about an hour until the moisture evaporates When you play 8 cm 3 in CDs Use the optional Sony compact disc single adapter CSA 8 to protect the CD player from being damaged Maintenance Fuse replacement When replacing the fuse be sure to use one that matches the amperage described on the fuse If the fuse blows check the power connection and replace the fuse If the fuse blows again after replacement there may be an internal malfunction In such a case consult your nearest Sony dealer Fuse 10 A Warning Never use a fuse with an amperage rating exceeding the one supplied with the unit as this could damage the unit Dismounting the Unit 1 While pushing in on the left side of the front cover insert the tip of a thin screwdriver as shown in the illustration then pry off the front cover Thin screwdriver Be careful not to break the front cover 2 Repeat step 1 on the right side Then the front cover will be removed y 3 Use a thin screwdriver to push in the clip on the left side of the unit then pull out the left side of the unit until the2. catch clears the mounting uoewoy u EUOIPPY H 11 12 Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION 17 watts per channel minimum continuous average power into 4 ohms 4 channels driven from 20 Hz to 20 kHz with no more than 1 total harmonic distortion Other specifications CD player section System Compact disc digital audio system Signal to noise ratio 90 dB 10 20 000 Hz Below measurable limit Frequency response Wow and flutter Laser Diode Properties Material GaAlAs Wavelength 780 nm Emission Duration Continuous Laser output power Less than 44 6 pW This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick up Block Tuner section FM Tuning range Antenna terminal 87 5 107 9 MHz External antenna connector Intermediate frequency 10 7 MHz Usable sensitivity 8 dBf Selectivity 75 dB at 400 kHz Signal to noise ratio 65 dB stereo 68 dB mono Harmonic distortion at 1 kHz 1 0 stereo 0 5 mono Separation 35 dB at 1 kHz Frequency response 30 15 000 Hz Capture ratio 2 dB AM 530 1 710 kHz External antenna connector 10 71 MHz 450 kHz 30 pV Tuning range Antenna terminal Intermediate frequency Sensitivity Power amplifier section Outputs Speaker outputs sure seal connectors Speaker impedance 4 8 ohms Maximum power output 40 W x4 at 4 ohms General Outp
3. PL 2 Press DSPL for two seconds NM tbl LI The hour digit flashes Set the hour digits To go back To go forward payers Bud H The minute digits flash Set the minute digits To go back To go forward 4 a mMm rx _ X mvs te i 3 Press OSPE momentarily ggg The clock is activated i m pe Note If the car has no accessory position on the ignition key switch the clock cannot be set unless the power is turn on Set the clock after you have turned on the radio or started CD playback CD Player Listening to a CD Simply insert the CD Playback starts automatically Labelled side up If a CD is already inserted press repeatedly until CD appears c IN me m S SEC gais Elapsed playing t Ml 1 i Note To play back an 8 cm 3 in CD use the optional Sony compact disc single adapter CSA 8 To Press Stop playback or Eject the CD Changing the displayed items Each time you press DSPL the item changes as follows m gt Elapsed playing time gt Track number Time 4 Locating a specific track Automatic Music Sensor AMS During playback push the SEEK AMS control up or down momentarily SEEK AMS To locate succeeding pei pe tracks To locate preceding tracks iiad Locating a specific point in a track Manual Search During playb
4. S ONY 3 861 727 31 1 FM AM Compact Disc Player Operating Instructions Owner s Record The model and serial numbers are located on the bottom of the unit Record the serial number in the space provided below Refer to these numbers whenever you call upon your Sony dealer regarding this product Model No CDX 2180 Serial No For installation and connections see the supplied installation connections manual COMPACT DIGITAL AUDIO CDX 2180 1998 by Sony Corporation Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipme
5. ack push the SEEK AMS control up or down for about two seconds Release when you have found the desired point To search forward 7 SEEK AMS Pri Pp To search backward Note f L ULL or 77747 appears in the display you have reached the beginning or the end of the disc and you cannot go any further Playing a CD in various modes Playing tracks repeatedly Repeat Play Press 1 during playback REP appears in the display When the currently played track is over it will be played again from the beginning To cancel this mode press again Playing tracks in random order Shuffle Play Press 2 during playback SHUF appears in the display All tracks on the CD are played in random order To cancel this mode press again Radio Memorizing stations automatically Best Tuning Memory BTM This function selects from the currently received band the stations with the strongest signals and memorizes them in order of their frequency PREVENTING ACCIDENTS When tuning in while driving use the automatic tuning instead of manual tuning 1 Press repeatedly to select the tuner Each time you press SOURCE the mode changes as follows CD gt TUNER 2 Press repeatedly to select the band Each time you press MODE the mode changes as follows gt FMI gt FM Il gt FM Ill gt AM 3 Press BTM SENS for two seconds The unit stores stations
6. frequency signal with a sharper curve than conventional bass boost You can hear the bass line more clearly even if the vocal sound is the same volume You can emphasize and adjust the bass sound easily with the D bass control This effect is similar to the one you get when you use an optional subwoofer system Moreover the Digital D bass function creates even sharper and more powerful bass sound than Analog D bass Digital D bass is available during CD playback Digital D BASS Analog D BASS o o gt D BASS 3 g D BASS 3 8 D BASS 2 3 aO D BASS 2 x D BASS 1 XK oeass 1 Frequency Hz Adjusting the bass curve Turn the D BASS dial to adjust the bass level 1 2 or 3 D BASS appears in the display During CD playback DIGITAL D BASS appears in the display To cancel turn the dial to the OFF position Note If the bass sound becomes distorted adjust the D bass dial or volume control Attenuating the beep tone Press 6 while pressing SOUND To obtain the beep tone again press these buttons again Note If you connect an optional power amplifier and do not use the built in amplifier the beep tone will be disabled Turning on the clock display power SELECT function Only for cars with an accessory position on the ignition key switch To turn the Power Select function ON Press while pressing SOUND The Power Select function ties the clock display power to the accessory positi
7. h the SEEK AMS control up or down repeatedly until the desired station is received Note If the automatic tuning stops too frequently press momentarily until LCL appears in the display local seek mode Only the stations with relatively strong signals will be tuned in Tip If you know the frequency of the station you want to listen to push the SEEK AMS control up or down for two seconds until the desired frequency appears manual tuning If FM stereo reception is poor Monaural Mode Press momentarily until MONO appears The sound improves but becomes monaural ST disappears To go back to the normal mode press again until MONO disappears Changing the displayed items Each time you press DSPL the items alternate between the frequency and time Other Functions Adjusting the sound characteristics You can adjust bass treble balance and fader Each source can store the bass and treble level independently 1 Select the item you want to adjust by pressing repeatedly VOL volume BAS bass gt TRE treble BAL left right gt FAD front rear 2 Adjust the selected item by rotating the dial Adjust within three seconds after selecting the item After three seconds the dial functions as volume control Changing the sound and beep tone Boosting the bass sound D bass You can enjoy clear and powerful bass sound The D bass function boosts the low
8. in the order of their frequencies on the number buttons Notes e The unit does not store stations with weak signals If only a few stations are received some number buttons remain empty e When a number is indicated in the display the unit starts storing stations from the one currently displayed e Ifa CD is not in the unit only the tuner band appears even if you press SOURCE Memorizing only the desired stations You can store up to 6 stations on each band 18 for FM I FM II and FM III 6 for AM in the order of your choice 1 Press repeatedly to select the tuner 2 Press repeatedly to select the band 3 Push the SEEK AMS control up or down to tune in the station that you want to store on the number button 4 Press the desired number button CD to for two seconds until MEM appears The number button indication appears in the display Note If you try to store another station on the same number button the previously stored station will be erased Receiving the memorized stations 1 Press repeatedly to select the tuner 2 Press repeatedly to select the band FM I FM II FM Ill or AM 3 Press the number button GD to momentarily where the desired station is stored olpey sake d qd H If you cannot tune in a preset station Push the SEEK AMS control up or down momentarily to search for the station automatic tuning Scanning stops when the unit receives a station Pus
9. nt into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment CAUTION The use of optical instruments with this product will increase eye hazard Welcome Thank you for purchasing the Sony Compact Disc Player This unit lets you enjoy a variety of features Table of Contents Location Of CONEIOIS scecseesseessesseesteeseesesseesneeseesees 4 Additional Information P PYCCAUTIONS sareen a i diiis 9 Getti ng Started Maintenance sssssesiersrrrsssissiiisrersisssereresisnaidssesra 10 Resetting the unit Dismounting the Wits isisisi 11 Setting the clock Specifications Troubleshooting guide CD Player Listening t0 a CD u ccssssssssessesssssessscssseeneessssseneens 6 Playing a CD in various modes eesceeeeeees 6 Radio Memorizing stations automatically Best Tuning Memory BTM sses 7 Memorizing only the desired stations 7 Receiving the memorized stations 000 7 Other Functions Adjusting the sound characteristics 8 Changing the sound and beep tone 0 8 Turning on the clock display POWER SELECT function 0 9 Location of controls Refer to the pages for details SEEK AMS seek Automatic M
10. on on the ignition key switch To avoid battery wear the clock is not displayed while the unit is initializing Additional Information Precautions e If your car was parked in direct sunlight resulting in a considerable rise in temperature inside the car allow the unit to cool off before operating it e If no power is being supplied to the unit check the connections first If everything is in order check the fuse e If no sound comes from the speakers of a two speaker system set the fader control to the center position e If your car is equipped with a power antenna note that it will extend automatically while the unit is operating If you have any questions or problems concerning your unit that are not covered in this manual please consult your nearest Sony dealer Notes on handling CDs A dirty or defective disc may cause sound dropouts while playing To enjoy optimum sound handle the disc as follows Handle the disc by its edge To keep the disc clean do not touch the surface Do not stick paper or tape on the labeled surface continue to next page UOHEWJO U EUOIIPpY SUO UNY 194 0 01pey H 10 Do not expose the discs to direct sunlight or heat sources such as hot air ducts or leave them in a car parked in direct sunlight where there can be a considerable rise in the temperature inside the car Before playing clean the discs with an optional cleaning cloth Wipe each disc from the center
11. ther CD is already loaded e The CD was forcibly inserted upside down Play does not begin Dusty disc CD is automatically ejected The ambient temperature is more than 50 C 122 F CD will not eject Press the amp button for two seconds The operation buttons do not function The sound skips due to vibration Press the reset button e The unit is installed at an angle of more than 60 e The unit is not installed in a sturdy part of the car Radio reception Problem Preset tuning is not possible Cause Solution e Store the correct frequency e The broadcast signal is too weak Automatic tuning is not possible The broadcast signal is too weak Use manual tuning The ST indication flashes e Tune in the frequency correctly e The broadcast signal is too weak Set to the MONO mode page 8 uonewoy u JEUOIIPPY H 13 14 Error displays The following indications will flash for about five seconds Display Cause Solution mL A CD is dirty or inserted upside Clean or insert the CD correctly E 004 down E 999 The CD player cannot be operated Press the reset button or amp because of some problem If the above mentioned solutions do not help improve the situation consult your nearest Sony dealer Sony Corporation Printed in Korea
12. usic Sensor manual search control 6 7 8 MODE band select button 7 SOURCE source select button 6 7 Dial volume bass treble left right front rear control 5 8 SOUND button 5 8 9 Display window Boao Ae a DSPL display mode change time set button 5 6 8 E 4 eject button 6 E BTM SENS Best Tuning Memory sensitivity adjust button 7 8 f Reset button located on the front side of the unit hidden by the front panel 5 OFF button 5 6 9 During radio reception Number buttons 7 During CD playback CG REPEAT button 6 SHUF button 6 D BASS dial 9 Getting Started Resetting the unit Before operating the unit for the first time or after replacing the car battery you must reset the unit Press the reset button with a pointed object such as a ball point pen Reset button Notes e Pressing the reset button will erase all the memorized program and memory functions e When you connect the power supply cord to the unit or reset the unit wait for about 10 seconds before you insert a disc Do not insert a disc within these 10 seconds otherwise the unit will not be reset and you will have to press the reset button again Setting the clock The clock has a 12 hour digital indication Example Set the clock to 10 08 1 Press or during operation If the POWER SELECT function is set to ON press OFF If it is set to OFF press DS
13. uts Line outputs 2 Power antenna relay control Power amplifier control lead Telephone ATT control lead Tone controls Bass 10 dB at 100 Hz Treble 10 dB at 10 kHz Power requirements 12 V DC car battery negative ground Approx 178 x50 185mm 7 8x2x7 s in w h d Approx 182 x 53 x 162 mm 7 4x2 sx6 2in w h d Mass Approx 1 2 kg 2 Ib 10 oz Supplied accessories Parts for installation and connections 1 set RCA pin cord RC 63 1 m Cleaning cloth XP CD1 Compact disc single adapter CSA 8 Dimensions Mounting dimensions Optional accessories Design and specifications are subject to change without notice Troubleshooting guide The following checklist will help you remedy the problems that you may encounter with your unit Before going through the checklist below check the connection and operating procedures General Problem No sound Cause Solution e Rotate the dial in a clockwise direction to adjust the volume e Set the fader control to the center position for two speaker systems The contents of the memory have been erased e The power cord or battery has been disconnected e The reset button has been pressed Store the settings again into the memory No beep tone e An optional power amplifier is connected and you are not using the built in amplifier e The beep tone is attenuated page 9 CD playback Problem CD cannot be loaded Cause Solution e Ano
Download Pdf Manuals
Related Search