Sony CD-R/RW User's Manual
Contents
1. EVITER TOUTE EXPOSITION DIRECTE AU FAISCEAU VORSICHT UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GE FFNET NICHT DEM STRAHL AUSSETZEN ADVARSEL USYNLIG LASERSTRALING VED ABNING UNDGA UDS ETTELSE FOR STRALING ADVARSEL USYNLIG LASERSTRALING NAR DEKSEL APNES UNNGA EKSPONERING FOR STRALEN VARNING OSYNLIG LASERSTRALING NAR DENNA DEL AR PPNAD STRALEN AR FARLIG VARO NAKYMATON AVATTAESSA OLET ALTTINA LASERSATEILYLLE ALA KATSO SATEESEN This label is located on the bottom of the drive unit enclosure This unit uses CD R discs and CD RW discs COMPACT with the following mark xao Recordable ReWritable This unit uses CD ROM discs with the following mark alice When you use this unit as a CD player use compact COMPACT discs with the following mark ISO DIGITAL AUDIO You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference2. lat raux et de la plaque inf rieure Abmessungen Wichtig Die Schrauben d rfen nicht mehr als 6 0 mm ber die Seiten oder Bodenbleche hinausragen Esquema de dimensiones Importante Los tornillos de montaje no deben nunca sobrepasar m s de 6 mm de la superficie de los paneles laterales o del panel inferior de la unidad Dimensioni Importante La sporgenza delle viti non pu superare il limite di 6 mm dalle superfici dei pannelli 8 Iffo o oo 8 2 8v ope epeo e p EW ody sojiuj01 g alias Japal jne gn uebuniuoqqneiuos g nei 1uBo Jad gi oibBessy IP ni 8 8199 enbeuo ep y EIN e8ejuoui ep si e sno g EW o1bbessy Ip ni EW Odi soju40 t W ueBuniugoqgneiuos p EIN eBejuoui ep si E SNO epis uoee uo y sejou Bununow EN 8 sejou Bununou EW 7 l eel BeBe mm inch INTERFAGE CONNECTOR PI eS orb
3. on pin 1 of host adapter e The following is a sample configuration of CD RW installation CD R W Drive ae gp T sua Power Supply inc Cable Audio Cable included SCSI S Cable Not included Red Edge O m 71 OO 50 2 oo Sound Card Not included SCSI Card Not included Speakers Not included Step 10 Closing the Computer Carefully replace computer cover per Owner s Manual Hardware installation is now complete 14 Hardware Installation Software Installation Please refer to CD RW formatting software CD manual for instruction on software installation CD RW formatting software must first be properly installed in order to write CD s with this device Using Discs Storing Discs e Do not store the disc in a location subject to high humidity high temperature excessive dust direct sunlight Care of Discs e Only hold disc by its edge Do not touch the record surface e Do not wipe CD R RW discs before recording data To avoid scratching the recording surface blow away dust using an air blower Software Installation Using Discs 15 Operating the Drive Assure application software is installed before using the CD RW drive Starting Up 1 Turn on the computer 2 Press eject button and the tray extends from drive unit Note Eject button does not function if softwar
4. professionals For Europe German or English contact the hotline at Tel 49 0 2389 951047 or SONY HOTLINE SUPLIE COM Monday Thursday 8 00 am 4 30 pm Friday 8 30 am 2 00 pm For DK N SW amp FIN please call Tel 47 0 6281 8666 Monday Friday 8 30 am to 4 00 pm Norwegian time Within the UK please call Tel 0870 900 8166 Monday Friday 8 45 am to 5 00 pm For France please call 33 0 155 870 866 Monday Friday 9 00 am to 6 00 pm or E Mail sony hlGnati fr All this information and more may be downloaded from the Internet Simply access the following address http www sony cp com Technical Support 19 Specifications E General Host interface SCSI 2 single ended 50 pin E Audio Line out 0 7 V at 47 kQ Headphone 0 55 V at 32 Q E Environmental conditions Relative humidity 1096 to 9096 no condensation Climate gradient 10 C hour 10 humidity hour Temperatures Operating 5 C to 45 C 41 F to 113 F Transport 40 C to 60 C 40 F to 140 F 72 hours max Storage 30 C to 50 C 22 F to 122 F 6 month max Design and specifications subject to change without notice 20 Specifications Dimension diagram Important The overhang of the screws should not exceed 6 0 mm from the surface of the side panels or the bottom plate Sch ma des dimensions Important Le d passement des vis ne doit pas exc der 6 0 mm par rapport la surface des panneaux
5. will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help CLASS 1 This CD R RW drive unit is classified as a CLASS 1 LASER LASER PRODUCT PRODUCT LASER KLASSE 1 The CLASS 1 LASER PRODUCT label is located at the PRODUNT bottom of the enclosure Trademarks e MS DOS Windows Windows 95 98 NT are registered trademarks of Microsoft Corporation e Pentium is a trademark of Intel Corporation e IBM PC PC XT and PC AT are registered trademarks of International Business Machines Corporation e PHOTO CD is a registered trademark of Eastman Kodak Company Contents Introduction 5 Featuress Lila e re regio irte qoe ai ica System Requirements for WINDOWS 95 98 NT Location and Function of Parts and Controls 6 Front Panel Rear Panel sss 6 Precautions 7 Hardware Installation 7 Installing the Drive Unit into the Computer i T Getting Started ECCE 7 St
6. CD R RW SCSI Drive Unit CD R RW SCSI Drive Unit User s Guide Mode d emploi Bedienungsanleitung Manual de instrucciones Manuale d istruzione User s Guide Mode d emploi Bedienungsanleitung 1999 by Sony Corporation Manual de Instrucciones BKG 98001684 Manuale d istruzione Owner s Record The model and serial numbers are located on the top of the drive Record these numbers in the spaces provided below Refer to them whenever you call upon your sales representative regarding this product Model No Serial No Safety Regulations To prevent fire or shock hazard do not expose the unit to rain or moisture To avoid electrical shock do not open the cabinet Refer servicing to qualified personnel only Caution As the laser beam in this CD R RW drive is harmful to the eyes do not attempt to disassemble the cabinet Refer servicing to qualified personnel only The use of optical instruments with this product will increase eye hazard The use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation DANGER INVISIBLE LASER RADIATION WHEN OPEN AVIOD DIRECT EXPOSIRE TOP BEAM VORSICHT This label is located on the drive unit s internal chassis ee LASERSTRAHLUNG WENN ABDECKUNG NICHT DEMSTRAHL AUSSETZEN DANGER INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM DANGER RADIATIONS INVISIBLES DU LASER EN CAS D OUVERTURE
7. SI devices HDD Scanner CD ROM connected to the SCSI cable If so determine the SCSI ID of each SCSI device This information is required for Step 5 Setting the Jumpers Refer to SCSI device s for ID data In some cases a SCSI chip set may be implemented on the motherboard 8 Hardware Installation Step 3 Finding the Connector The SCSI cable should have 1 or more unused connectors on the end opposite the adapter as shown find a connector not in use We recommend a connector at the very end of the 50 pin SCSI cable SCSI host adapter connector Pin 1 red Opposite End Note If no free 50 pin SCSI connector exists see Troubleshooting page 18 Step 4 Choosing the Configuration SCSI ID selection Termination e If no other SCSI devices are in the system we recommend the default jumper settings In this case go on to Step 6 Connecting the Drive e If one or more SCSI ID s are assigned you must determine if the default ID 6 is free If SCSI ID 6 is assigned you must change the CD R drive to a free ID via jumpers at rear of drive see Step 5 e If CD RW drive is the last physical device on SCSI cable leave Active Term jumper in place Previous last SCSI device may need to be un terminated e If CD RW drive is not on end of SCSI cable or last physical device remove the Active Term jumper and assure the last physical SCSI device is properly terminated or activ
8. W Drive Unit Pin 1 Audio Out Connector SCSI Flat Cable Notes The 50 pin flat SCSI cable must be firmly attached with its red edge Pin 1 positioned next to the power supply connector If computer has a Sound Card an Audio Cable may be connected to the rear of the CD RW drive Contact a local dealer if cable is required 12 Hardware Installation Step 7 Mounting the Drive Insert the CD RW drive into computer front as shown routing cables accordingly Secure drive to frame with appropriate screws us PF oum Flat Cable Audio Cable 7 Note Slide rails not included may be necessary if you cannot secure CD RW drive Refer to your computer s User s Guide for more information Step 8 Connecting the Power Cable Locate an available power supply cable within computer and connect it to the rear of CD RW drive as shown Power Supply Connector DC INPUT 5V 5 GND 12Vt10 SSS Power Supply Cable S Note The power supply cable connector is designed to fit one way do not force it upside down this could damage drive and void the warranty Hardware Installation 13 Step 9 Installation Review Now let us review the hardware installation process assuring that All connectors are properly connected Each SCSI device has its own unique SCSI ID number The last physical SCSI device on the bus is properly terminated Red Edge Notes Red edge of 50 pin flat SCSI cable must be
9. ated Note Only the last physical SCSI device needs to be terminated Hardware Installation 9 Step 5 Setting the Jumpers Set jumpers on rear of drive unit according to your computer configuration Jumpers are factory preset as shown below ACTIVE TERM TEST ID1 ID2 ID4 10 Hardware Installation The following table shows the function of each jumper ACTIVE TERM TEST i ii Bi ak jumpers to ON or OFF Do not assign the same number as one used for other SCSI device Jumper Function ACTIVE ON Enables active termination TERM OFF Disables active termination TEST ON Enables test mode OFF Enables normal operation ID SELECT Assign the drive unit s ID number by setting these ID number Jumper settings 0 OFF OFF OFF 1 ON OFF OFF 2 OFF ON OFF 3 ON ON OFF 4 OFF OFF ON 5 ON OFF ON 6 OEE ON ON Notes Factory settings e The upper row of pins is without position KEY is ground e Remove jumper to set OFF install jumper to set ON e ID SELECT ACTIVE TERM and TEST MODE are recognized when the power supply is turned on or the SCSI bus is reset e TEST mode is used exclusively for factory testing Do not set TEST mode to ON Doing so may cause unexpected disastrous results Hardware Installation 11 Step 6 Connecting the Drive Attach flat SCSI cable to connector at rear of CD RW drive CD R
10. ck via Audio Out and headphones jack Note Please read this manual thoroughly before attempting installation System Requirements for WINDOWS 95 98 NT e System requirements of format software SCSI host adapter card Bus Mastering 150 MB or more free hard disc space 3 5 floppy disk drive Mouse Microsoft compatible 32 MB of RAM or more Introduction 5 Location and Function of Parts and Controls Front Panel COMPACT GITE Recordable ReWritable Disc Drawer Emergency Eject Eject Hole Button Headphone Headphone Busy Jack Volume Indicator Control Rear Panel ACTIVE TERM TEST AUDIO OUT ID SELECT DC INPUT RGNDL 612 5V 5 GND 12V 10 ini INTERFACE CONNECTOR Jumper block for SCSI bus Power in connector Audio output connector SCSI bus interface connector 6 Location and Function of Parts and Controls Precautions Bi Installation e Avoid placing the drive in a location subject to high humidity high temperature excessive dust mechanical vibration direct sunlight Only horizontal drive operation recommended not vertical or tilted E Operation e Do not move drive during operation it may cause an error Avoid sudden temperature changes condensation may form inside the drive Should ambient temperature suddenly change wait at least 1 hour before turning off power Operation immediately after temperature change may cause a malfunction E Transpo
11. e disabled Insert disc into drive slot with disc label facing up Push gently until auto load mechanism pulls tray into drive Important When loading a disc do not attempt to overpower the auto load 16 Operating the Drive As the drive begins reading the Table of Contents TOC data the busy indicator lights and remains illuminated until read is completed When the busy indicator switches off the drive is ready to receive commands data may be retrieved from the disc After loading a disc it takes a moment for the drive to become ready while Program Memory Area is read From this point follow instructions provided with the application software Note Busy indicator on drive continues to light amber if disc is not properly inserted or a malfunction occurs In such a case eject the disc tray and reinsert it properly Should the light remain amber consult your dealer or qualified service point During audio play the busy indicator remains amber this is normal M Opening the drawer tray manually in an emergency In the event of electrical or mechanical drive failure a manual emergency eject is provided to allow manual disc removal 1 Turn off the computer and remove power cable 2 Insert a pointed object perhaps a paper clip into the emergency eject hole and push typical force required is 46 N 4 7 kg at least 35 mm After thus removing disc consult dealer or qualified service point Operating the Dri
12. ep 1 Opening the Computer ii Step 2 SCSI Configuration cniara iran ziale Step 3 Finding the Connector iii Step 4 Choosing the Configuration Step 5 Setting the Jumpets eicere erect ee erret us Step 6 Connecting the Drive esee Step 7 Mounting the Drive correct retener i Step 8 Connecting the Power Cable EC Step 9 Installation Review i 14 Step 10 Closing the Computer ii 14 Software Installation 15 Using Discs 15 ione c S 15 Careiot DISCS E 15 Operating the Drive 16 starting Up 16 Troubleshooting 18 Checklist a assa iaia nigi 18 Additional Installation Cases i 18 Technical Suppi iaia tene aaa rte ee ti err Ys 19 Specifications 20 Dimension diagram onere iaia Last page of manual Introduction Features This CD R RW drive has the following features General e 5 1 4 inch half height drive form factor Fast SCSI bus interface embedded based on SCSI 2 Integrated buffer memory Power tray loading and ejection manual eject too Housed in an airtight frame casing Supported formats and modes e CD ROM mode 1 CD ROM XA Mode 2 form 1 amp 2 data e PHOTO CD read only amp Video CD CD I Mode 2 form 1 and 2 e CD DA CD EXTRA and CD I Ready read only e CD TEXT CD Recordable amp CD ReWritable Audio e Outputs 16 bit digital audio data over SCSI interface e Audio CD playba
13. rtation Keep the original packing materials for future transport of the drive Hardware Installation Installing the Drive Unit into the Computer This example assumes an IBM PC AT compatible computer a SCSI adapter card and a SCSI interface cable 50 pin flat are at hand Getting Started Assure SCSI adapter is operational before installing CD R RW drive Prepare the necessary parts and tools not supplied a screwdriver Two mounting rails if computer has mounting racks Precautions Hardware Installation 7 Step 1 Opening the Computer First turn off computer and remove unplug all power cables Remove computer cover as directed in the User s Manual Step 2 SCSI Configuration Locate the 50 pin SCSI cable in your computer One end of the cable is connected to the SCSI host adapter card as shown below 4 SCSI Host Adapter Card ZN L Eo ua Red Edge SCSI SCSI SCSI Device Device Device Note The following types of cables may be installed in your computer TT m Ti xs IC i wi c Find this 68 Pin i 40 Pin 34 Pin I flat cable 50 Pin Width Width I Width EXP um I Floppy Disk J _ SCSI Cable ID Cable Drive Cable Adapter required not included Note There may already be internal or external SC
14. ve 17 Troubleshooting Checklist Should problems occur while installing or operating the drive e Please verify the steps of this manual were carefully followed e If problem still exists please confirm the items in Checklist below Please verify the following e Power cable properly attached to drive Step 8 on page 13 When properly connected the LED lights e Both ends of SCSI cable are properly attached check pin 1 position e SCSI ID of CD RW is unique to SCSI bus Compare all other SCSI devices internal and external and see Step 2 Step 5 pages 8 11 e Check all other jumpers on rear of drive We recommend factory defaults on pages 10 and 11 with a SCSI ID 6 if possible e Assure SCSI bus is properly terminated or activated at both ends For details please see Step 4 Termination on page 9 Should you still have problems operating or installing your CD RW drive please contact our hotline or your local computer dealer Additional Installation Cases E No free SCSI connector present If other SCSI devices occupy ever bus connector either remove a device before installing CD RW drive or use a SCSI cable with more connectors Please contact a local computer dealer for details W 68 Pin SCSI Cable If a wide SCSI cable 68 pin is used a 50 pin adapter is necessary 18 Troubleshooting Technical Support If you require further support or service please contact your local Sony technical support
Download Pdf Manuals
Related Search