Snap-On 870016 User's Manual
Contents
1. Al air compressors must comply with the requirements of ANSI ie 619 3 Pressure regulators must be used to limit air pressure where air supply pressure exceeds the tool s rated operating pressure Do not carry the brad nailer with a finger on the trigger This could lead to an accidental discharge of the brad nailer Do not press the trigger of the brad nail er unless it is pressed firmly against the work piece Do not point the brad nail er at yourself or in the direction of another person Failure to comply with this warning could result in serious injury or even death to the operator or other bystanders Do not tamper with the work piece contact The work piece contact prevents accidental discharge of the brad nailer and should never be removed or com promised in any way Failure to comply with this warning could result in seri ous injury or even death to the operator or other bystanders Always disconnect air hose and remove any remaining nails 1 When brad nailer is left unattended 2 Before performing any maintenance or repair on the brad nailer 3 Before attempting to clear a jam in the brad nailer 4 Before moving the brad nailer to a new location Always check the overall condition of the brad nailer before using Check for and tighten any loose screws Ensure all safety systems are in working condi tion before using the brad nailer The brad nailer must not operate if only the trigger is pulled or if only the work p2. Store the brad nailer in a safe location or in suitable carrying case It is recommended that the air nailer be secured in a locked location to prevent unauthorized usage Avoid exposure to direct sunlight and or locations with high humidity and heat 4 WARNING Remove the brad nailer from use and schedule to have it repaired at an authorized repair facility if the work piece contact is bind ing or not moving freely Do not attempt to repair the brad nailer Failure to comply can result in malfunction of the tool and severe injury to the opera tor or any bystanders 16 M ANDATORY MAINTENANCE 4 WARNING All maintenance and repairs should be performed by an authorized repair facility Call 1 888 278 8092 to obtain a list of repair facil ities in your area or to make arrangements to return the tool for service ACTION Clean magazine and feeder mechanism Inspect and ensure work piece contact operates properly Lubricate brad nailer after every use using pneumatic tool oil REASON Prevents brad nailer from jamming Ensures operator safety and keeps brad nailer working efficiently Extends life of brad nailer OPERATION Use compressed air and clean daily Use compressed air and clean daily Apply 2 3 drops of pneumatic tool oil to brad nailer air inlet after every use PROBLEM Weak drive Slow to cycle between nailings Nails driven too deep Brad nailer feeds inter mittentl
3. WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE LIMITATIONS ON WARRANTY DISCLAIMERS Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of the incidental or consequen tial damages so part or all of the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state If your product is not covered by this warranty please call our Customer Service Department at 1 888 278 8092 for general repair information and charges and the location of your nearest authorized service facility 26
4. damage When 23 sending your product include your name address phone number e mail address dated proof of purchase or copy and a statement about the nature of the problem Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate written proof that they are the original purchaser and of the original purchase date Parts returned freight prepaid and insured will be inspected and at Alltrade s option repaired and or replaced free of charge if it is found to be defective and sub ject to warranty Alltrade retains the sole discretion to determine whether any item or part is nonconforming and if so whether the item and or part will be repaired and or replaced If the unit is repaired new or reconditioned replacement parts may be used If Alltrade chooses to replace the product it may replace it with a new or reconditioned of the same or comparable design The repaired or replaced unit will be warranted under the terms of the remainder of the one year warranty period cov ered defective parts not subject to normal wear and tear or other exclusions will be repaired or replaced at Alltrade s option During the warranty period Alltrade will be responsible for the return shipping charges Alltrade s repair and or replacement of any nonconforming item and or part thereof shall constitute fulfillment of all obli gations to the purchaser Alltrade shall not be responsible or liable for any expense including freight ch
5. pay particular attention to all the DANGER MAINTENANCE C 15 16 WARNING CAUTION and NOTE statements of this manual MANDATORY MAINTENANCE een RR 17 TROUBLESHOOTING ii eee 17 18 A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all PARTS DIAGRAM cawi sa gera n 4 1 63 4 SAT aC ata 19 safety messages that follow this symbol to avoid PARTS LIST ure naturae Sind Eo Eae ea E EE nd oe 20 22 possible injury or death SPECIFICATIONS 0 0 ccc eee RR 29 1 YEAR LIMITED WARRANTY 0 0 c cece ee 23 26 A DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage CAUTION NOTE provides additional information that is useful for proper use and maintenance of this tool If a NOTE is indicated make sure it is fully understood NOTE In addition to SAFETY ALERTS listed above there could also be numerous symbols alerting the operator that specific safety equipment is required to safely o
6. see Exclusions to be free from defects in materials and workmanship for a period of one year from the original date of purchase NAIL DIAMETER NET WEIGHT The date of purchase shall be the date of shipment to the original purchaser or the date the original purchaser took possession custody or control of the product whichever occurred first This warranty shall be null and void if the product or any component thereof is modified or altered This warranty does not apply to any other product and or component thereof manufactured or distributed by Alltrade and does not apply to products and or components thereof designed manufactured and or assembled by others for which Alltrade makes no warranties whatsoever THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF WARRANTY PERFORM ANCE By purchasing this product purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provid ed that any such nonconforming item and or part is promptly returned to an author ized Service Center within the applicable warranty period with a written request by purchaser to repair and or replace the nonconforming item and or part We recom mend that you keep the original product packaging in the event you need to ship the unit We suggest the package be insured against loss or in transit
7. EQUIRED DAILY PREPARATION The following steps should be performed on a daily basis to ensure the brad nailer is operating correctly 1 Disconnect air supply from nailer and remove fastener strip 2 Check all screws nuts and pins and ensure all are tight 3 Press the pusher release button and slide back the pusher assembly Overriding the reload indicator Press the work piece contact against a work piece ensuring smooth movement 4 With work piece contact against the work piece pull trigger The trigger must operate smoothly 5 Connect air supply and set regulator for 70 psi DO NOT load a fastener strip 13 6 Select Single Sequential Actuation Operation Check for leaks Without pulling the trigger press the work piece contact against the work piece The tool MUST NOT operate Holding the tool away from the work piece pull trigger and hold for 5 seconds The tool MUST NOT operate Repeat steps several times Without pulling trigger press nailer against work piece and pull trigger The tool MUST operate Release trigger Driver MUST move up N Select Contact Actuation Operation Holding nailer away from work piece pull trigger The tool MUST NOT operate While still pulling trigger press the nailer against work piece The tool MUST operate Oo If Steps 1 through 7 function properly prepare the tool for use Select opera tion mode and load fasteners 9 Set the required depth of drive 10 Repeat these ste
8. FOR CUSTOMER SERVICE PARA EL SERVICIO PARA EL CONSUMIDOR 1 888 278 8092 Printed in Taiwan IONAD I2 SNAP ON IS A TRADEMARK LICENSED BY SNAP ON CORP U S A WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT CONSUMER INQUIRES SHOULD BE DIRECTED TO COPYRIGHT 2007 ALLTRADE TOOLS LLC 1431 VIA PLATA LONG BEACH CA 90810 1462 USA 870016 18 Gauge 1 1 4 Brad Nailer Rev 9 6 07 MODEL 870016 18 GAUGE 1 1 4 BRAD NAILER INSTRUCTION M ANUAL THS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY OPERATION MAINTENANCE AND STORAGE OF THS PRODUCT BEFORE USE READ CAREFULLY AND UNDERSTAND ALL CAUTIONS WARNINGS INSTRUCTIONS AND PRODUCT LABELS FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL IN URY AND OR PROPERTY DAMAGE IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WTH YOUR SNAP ON PRODUCT DO NOT RETURN THS PRODUCT TO THE STORE PLEASE CALL CUR CUSTOMER SERVICE DEPARTMENT AT 1 888 278 8092 BEFORE YOU CALL HAVE THE FOLLOWING INFORMATION AVAILABLE MODEL No DATE PURCHASED AND STORE LOCATION TABLE OF CONTENTS CONGRATULATIONS CONGRATULATIONS cl 9 Thanks for choosing this product Our aim is to provide you with the highest quality prod GENERAL SAFETY RULES 9 ucts and we want you to be totally satisfied with your product and our Customer Service uM nue ane eae O lf any help or advice is needed please contact us at 1 888 278 8092 When properly RECOGNIZE SAFETY SYMBOLS WORDS AND LABE
9. GARD TO THIS PRODUCT ALL WARRANTIES AND OR IMPLIED WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANU FACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COM PONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ON PRECEDING PAGES LIMITATIONS OF LIABILITY IN NO EVENT SHALL ALLTRADE AND OR ITS REPRESENTATIVE S BE LIABLE FOR INDIRECT INCIDENTAL SPECIAL AND OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF OR RELATED TO DIRECTLY OR INDIRECTLY ANY BREACH OR PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND OR ITS REPRE 25 SENTATIVE S AND PURCHASER AND WARRANTY HEREUNDER AND OR THE EXISTENCE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF ANY ITEM S SOLD HEREUNDER EVEN IF ALLTRADE AND OR ITS REPRESENTA TIVE S HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES IN NO EVENT WHETHER BECAUSE OF A BREACH OF CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE OR OTHERWISE SHALL ALLTRADE S AND OR ITS REPRESENTATIVE S LIABILITY EXCEED THE PRICE OF THE PRODUCT All LIA BILITY CONNECTED
10. LS 2 3 cared for this product will give you many years of satisfaction IMPORTANT INFORMATION ABOUT THIS MANUAL 4 SAFETY WARNINGS AND PRECAUTIONS 05 4 7 GENERAL SAFETY RULES FUNCTIONAL DESCRIPTION ss so cambia nie aac ror ded aea T COM PONENT INSTALLATION n OB ROB GROB o G G GG GB oG Ge G G3 G9 G39 G 3 S8 Gg G3 3 7 u 8 9 A WARNING READ AND FOLLOW ALL INSTRUCTIONS Failure to fol OPERATING THE BRAD NAILER ss sx epsa eee eee 9 13 low all instructions in this manual may result in severe personal injury or death SELECT TRIGGER ACTUATION MODE 005 9 10 Keep this manual and refer to it for Safety Instructions Operating Procedures ADJUSTING DEPTH OF NAILING 0 0 00 n n II 11 and Warranty USING THE HOOK Cr OR o R 0O 3G G oGoG G P EOS G G GB S G G G3 9 3 S GS OG 3 g SG G3 7 J JH NW S3 3 7 W 12 SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE LOADING NAILS INTO THE AIR NAILER 12 USING THE NO MAR NOSEPIECE seen 12 13 RECOGNIZE SAFETY SYM BOLS WORDS AND LABELS DESSES eb EO reg Wipe sr a enema eels The safety instructions provided in this manual are not intended to cover all possible USING THE AIR NAILER gt nss n n n nn 14 15 conditions and practices that may occur when operating maintaining and cleaning CHANGING DIRECTION OF EXHAUST AIR 005 15 power tools CLEARING JAMS isse nnn 15 Always use common sense and
11. arges or repairs made outside Alltrade s facility or an Alltrade designated service unless expressly agreed to by Alltrade in writing Under no cir cumstances shall Alltrade bear any responsibility for loss of the unit loss of time or rental inconvenience commercial loss or consequential damages For the location of an Authorized Service Center nearest you please call customer service at 1 888 278 8092 EXCLUSIONS Air nailers and staplers need periodic maintenance to remain in proper operating condition Normal wear parts o rings and driver blades shall be warranted to the original purchaser to be free from defects in materials and workmanship for a peri od of 90 days from the original date of purchase This warranty does not cover parts damaged due to normal wear abnormal condi tions misapplication misuse abuse accidents operation improper storage or freight damage Parts damaged or worn by operation in dusty environments are not warranted Failure to follow recommended operating and maintenance procedures also voids warranty DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING ACCIDENT ABUSE NEGLIGENCE FAILURE TO FOLLOW INSTRUCTIONS UNAUTHORIZED REPAIRS OR ALTERATIONS DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY USE OF UNAPPROVED OR IMPROPER ATTACHM ENTS OR ACCESSORIES OR OTHER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS WARRANTY 24 Alltrade will not be liable for the follow
12. asic safety rules and precautions Most accidents can be avoided if the operator recognizes a potentially hazardous situation before it happens and by observing appropriate safety rules and procedures as outlined in this manual Basic safety precautions are outlined in the SAFETY portion of this manual and throughout text in this manual where a potential hazard might occur Hazards that MUST be avoided to prevent serious injury follow headers marked DANGER or WARNING These same precautions are placed as labels on the tool itself NEVER use this nailer for applications that are NOT specified in this manual SAFETY WARNINGS AND PRECAUTIONS DANGER Do not operate brad nailer anywhere fastener may contact hidden electrical wiring Contact with a live wire will make all metal parts of the brad nailer live This can result in severe electrical shock severe burns or death to the operator Contact a qualified electrical contractor to ensure a safe working envi ronment exists Be aware of conduits or gas pipes Striking a gas pipe could result in an explo sion causing serious injuries or even death to the operator or bystanders Be aware of what is behind the work piece A fastener could travel through the work piece and out the other side striking a bystander resulting in serious injury or even death Do not operate the brad nailer in the presence of flammable liquids such as gasoline thinner paint or adhesives gases or
13. built up during operation A Remove jammed fastener If fastener is diffi cult to grasp use needle nose pliers instead of fingers C1 If necessary insert a flat blade screwdriver so that it touches the tip of the driver blade See Figure 8 Tap the screwdriver with a hammer The screwdriver will push the driver blade back freeing the jam 6 Close the jam clearing door securely MAINTENANCE STORAGE OF NAILS Always handle nail strips and their box very carefully If the nail strips have been mis handled they may be out of shape or have breaks in the connecting strips This will cause the nails to feed poorly and possibly result in misfiring or jams in the air nailer Avoid storing nails in a very humid or hot environment or place in direct sunlight 15 OVERALL MAINTENANCE OF AIR NAILER 4 WARNING Always disconnect the air hose from brad nailer before attempting any type of maintenance or visual inspection of tool Always visually inspect brad nailer before every use Check on the overall condition and for any loose screws Tighten any screws that have come loose See Figure 9 Visually inspect the work piece contact and trigger to ensure there is free movement See Figure 10 When the tool is not going to be used for an extended period wipe off all dust and debris that have collected on it Tighten all loose screws Lubricate the firing mechanism with pneumatic tool oil See page 9 for Lubrication
14. d the red Actuation Selector embedded in the trigger 2 Rotate Actuation Selector down to the Single Sequential Actuation T 3 Release Actuation Selector ensuring locking tab is fully seated in the slot Figure 1 4 CAUTION Ensure selector has locked into position Ensure actuation process is fully understood before attempting to use brad nailer TO USE THE BRAD NAILER IN SINGLE SEQUENTIAL ACTUATION MODE 1 Firmly grip brad nailer handle 2 Position brad nailer work piece contact on work piece surface 3 Push brad nailer against work piece compressing work piece contact 4 Pull trigger on brad nailer to drive nail The brad nailer will recoil away from the work piece as nail is driven 5 Remove finger from trigger and lift brad nailer away from surface of work piece OPERATION IN CONTACT ACTUATION MODE 4 WARNING When using contact actuation mode be careful of unin tentional double fires resulting from tool recoil Unwanted fasteners may be driven if the work piece contact is allowed to accidentally re contact the work piece 10 To select Contact Sequential Actuation Mode see Figure 2 1 Press and hold Actuation Selector embedded in the trigger 2 Rotate Actuation Selector up to the Contact Sequential Actuation TTT 3 Release Actuation Selector ensuring locking tab is fully seated in the slot 4 CAUTION Ensure selector has locked into position Ensure actuation proces
15. dust Sparks created by the tool can cause flammable materials to ignite or explode Failure to comply with this warn ing could result in serious injury or even death to the operator Keep bystanders children and visitors away from area where brad nailer is being used Distractions can result in severe injury or even death to anyone who inadvertently gets in the way of nailing operations Do not use oxygen combustible or bottled gases such as carbon ILE dioxide or nitrogen as a power source for the brad nailer Use only compressed air from a source as outlined in this manual The tool will explode resulting in severe injury or even death to the operator and bystanders Do not connect brad nailer to an air source capable of generating more than 200 psi 14 06 kg cm G Over pressurizing the brad nailer will result in bursting abnormal operation or breakage of the tool Use only clean dry regulated compressed air at levels speci fied on the tool Failure to comply can cause severe injury or death to the oper ator or bystanders Do not attempt to fasten the trigger in the ON position This could lead to an accidental discharge of the brad nailer Do not operate the brad nailer if any portion of the tool s operating controls are inoperable disconnected altered in any way or not in proper working order Failure to comply with this warning could result in serious injury or even death to the operator or other bystanders
16. ected from the power source Failure to comply with this warning can result in serious or permanent injury or even death to the operator or to bystanders Do not drive nails on top of other nails Do not operate the brad nailer at too steep of an angle Nails can ricochet Failure to comply with this warning can result in serious injury or even death to the operator or bystanders Do not modify the brad nailer in any way Unauthorized alterations can jeop ardize safety in the tool s operation Failure to follow this precaution can result in serious injury or even death to the operator or bystanders On rooftops and other high locations always move forward as you use the brad nailer You can easily loose your footing if moving backwards When nail ing against a perpendicular surface nail from the top down This causes less fatigue and reduces the chances of accidents Ensure the work area is sufficiently illuminated to operate power tools The work area should be clear and free of litter CONTROLS AND COMPONENTS Thoroughly clean and maintain the brad nailer after every use Lubricate moving parts to prevent rust and minimize friction related wear Wipe down the entire tool and remove all dust from the moving parts Properly store the brad nailer in a suitable case to keep it ready for the next job All maintenance and repairs should be performed by an authorized repair facility Call 1 888 278 8092 to obtain a list of repair facilit
17. et oiler reg ulator and air filter as close as possible to the air nailer Adjust the oiler so that approximately one drop of oil will be released for every 50 nails If an air set is not used or is unavailable oil the tool using pneumatic tool oil by plac ing 2 or 3 drops into the air inlet This should be done before and after use For proper lubrication the tool must be fired several times after the oil is introduced to the filter OPERATING THE BRAD NAILER 4 WARNING Always use hearing protection to protect your ears against aw hearing loss due to exhaust noise Always wear proper safe ty glasses to prevent injuries to the eyes from fragments of the work piece defective nails or other debris caused by using the brad nail er All safety glasses must have side shields and should conform to the require ments of the American National Standards Institute ANSI z87 1 Failure to comply with this warning could lead to serious or permanent damage to the ears as well as serious damage or permanent blindness in the eyes Always disconnect the air hose before making adjustments or checking the functionality of the air nailer SELECT TRIGGER ACTUATION M ODE The brad nailer is equipped with a selectable trigger This allows the selection of Single Sequential Actuation Mode or Contact Actuation Mode OPERATION IN SINGLE SEQUENTIAL ACTUATION MODE To select the Single Sequential Actuation Mode see Figure 1 1 Press and hol
18. iece contact is pressed against the work piece The brad nailer must only be used if both the trigger and work piece con tact work at the same time Always use hearing protection to protect your ears against IW hearing loss due to exhaust noise Always wear proper safe ty glasses to prevent injuries to the eyes from fragments of the work piece defective nails or other debris caused by using the brad nail er All safety glasses must have side shields and should conform to the require ments of the American National Standards Institute ANSI z87 1 Failure to comply with this warning could lead to serious or permanent damage to the ears as well as serious damage or permanent blindness in the eyes Never carry the brad nailer by the air hose A sudden disconnection of the air hose could cause the brad nailer to remain charged and an accidental firing could occur Failure to comply with this warning could lead to serious injury to the operator or bystanders Always disconnect the power source and ensure the tool is not charged before loading fasteners Failure to comply with this warning could cause severe injury or death to the operator bystanders and severe damage to the brad nailer Never use a non relieving air coupler with the brad nailer Always use cou plers that release any built up charge in the brad nailer s firing mechanism A non relieving air coupler can allow the brad nailer to discharge a fastener while the tool is disconn
19. ies in your area or to make arrangements to return the tool for service FUNCTIONAL DESCRIPTION 11 Work Piece Contact 1 Exhaust Cover 12 Trigger Actuation Mode Selector Trigger ACCESSORIES Jam Clearing Door 13 Lubricant No mar Nosepiece 14 Safety Glasses Empty Magazine Indicator 15 Hex Wrenches 2 Nail Depth Adjuster 16 F32 Brad Strips Hanging Hook Air Inlet Nail Magazine Lever Nail Magazine Cover oO ON DO FW PD COM PONENT INSTALLATION 4 WARNING Never use a non relieving air coupler with the brad nail er Always use couplers that release any built up charge in the brad nailer s fir ing mechanism A non relieving air coupler can allow the brad nailer to dis charge a fastener while the tool is disconnected from the power source Failure to comply with this warning can result in serious or permanent injury or even death to the operator or to bystanders When selecting an air compressor it must comply with the requirements of the American National Safety Institute ANSI B19 3 Choose an air compressor that can supply more than the required air pressure to ensure optimum efficiency Always use clean dry compressed air with a maximum pressure of 200 psi Use a pressure regulator and set the pressure between 60 115 psi 4 0 8 0 kg cm G Before each use check the pressure regulator to ensure it is functioning within the proper pressure range 4 WARNING Using a
20. iler in a high location or on an unstable platform LOADING NAILS INTO THE AIR NAILER Always disconnect the air hose from the brad nailer before adding or remov ing nails to the brad nailer NEVER use deformed nails or nail strip Failure to observe this precaution can result in poor nail feeding and or jams in the feeding mechanism To load nails in brad nailer depress magazine lever and pull magazine cover to back of magazine Figure 4 Insert nails and slide magazine cover over nails until it locks into place y7 LID Gna a ERN USING THE NO M AR NOSEPIECE 4 WARNING Always disconnect the air hose before attaching the no mar nosepiece 12 In order to prevent the surface of the work piece from being scratched or damaged use the no mar nosepiece Install no mar nosepiece by pressing it into place on the nose frame See Figure 5 Figure 5 4 WARNING Never use a non relieving air coupler with the brad nail er Always use couplers that release any built up charge in the brad nailer s firing mechanism A non relieving air coupler can allow the brad nailer to discharge a fastener while the tool is disconnected from the power source Failure to comply with this warning can result in serious or permanent injury or even death to the operator or to bystanders When the air hose is disconnected the pressure reservoir in the air nailer will dis charge removing any built up air inside the tool R
21. ing labor charges loss or damage resulting from improper operation maintenance or repairs made by other persons pre deliv ery services such as assembly oil and lubricants and adjustment maintenance services that are normally required to maintain the product The use of other than genuine Snap On Repair Parts will VOID the warranty WARRANTY DISCLAIMERS EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES GUAR ANTIES AND OR REPRESENTATIONS EXCEPT FOR THE LIMITED WARRANTY PROVIDED HEREIN ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE BUYER ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSE OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE NO WARRANTY ORAL OR WRITTEN OTHER THAN THE WARRANTY LISTED HEREIN IS MADE WITH RE
22. meter Check inside diameter of air hose nail is driven 17 18 PARTS DIAGRAM PARTS LIST ITEM NO PART NO DESCRIPTION Ls oweewe maem D ow mm D ow 9 20 e EEN O e YT gt 4 Aig y io 19 ITEM NO PART NO DESCRIPTION ITEM NO PART NO DESCRIPTION A0303 0901 Cylinder K0700 5771 Release Catch A0309 0741 A0711 2601 Release Catch C K0400 0601 Body and Handle Grip A0009 0071 Steel Ball A0005 1021 stopping Ring A0005 031 1 Pin Retainer 5 5 2 A0000 0071 Screw M5 16 Main Body Bumper R Snap on K0800 0411 Driver Guide Cover Set A0204 1571 No Mar Pad 21 22 O Ring 4 1 25 Red 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 61 62 63 64 65 67 70 71 72 73 74 SPECIFICATIONS MODEL NUMBER 870016 AIR PRESSURE 60 115 PSIG 4 0 8 0 kg cm 2G NAIL LENGTH 5 8 15 mm 1 1 4 31 75 mm NAIL CAPACITY 110 NAILS MINIMUM HOSE DIAMETER ad UU 18 GAUGE 2 6 LBS 1 17KG 1 YEAR LIMITED WARRANTY Express and Exclusive Limited Warranty to Original Retail Buyer Alltrade Tools LLC hereinafter Alltrade expressly warrants to the original retail purchaser of the accompanying SNAP ON portable air tool and no one else all parts of the product except those parts referred to below which are specifically excluded from such warranty
23. n air pressure of more than 120 psi can cause the brad nailer to malfunction or possibly explode causing i severe injury or property damage SELECTING A PROPER AIR HOSE Use an air hose with the largest diameter and shortest length possible to ensure continuous efficient nailing operations Using an air pressure of 70 psi 5 0 kg cm G an air hose with an inside diameter of 1 4 6 5 mm or greater and a hose length of less than 6 6 ft 20 m it is recommended that a 0 5 second interval be allowed between each nailing Air supply hoses shall have a minimum working pres sure of 150 psi 10 7 kg cm G or 150 of the maximum pressure produced by the compressor or whichever is higher 4 CAUTION Low air output by the compressor or a longer hose with a smaller inside diameter in relation to the nailing frequency may decrease the driving capability of the air nailer SELECTING A QUICK DISCONNECT 1 Remove the plastic protective plug from the tool s air inlet p 2 Insert a 1 4 NPT male quick MDD 01 23 disconnect into the air inlet Install the female portion to the air hose 8 To improve the connection between the quick disconnect and air nailer and to help prevent oxidation apply PTFE tape or joint compound to the connector threads before insertion 3 Snap the air hose onto the quick disconnect on the air nailer Check for air leaks LUBRICATION To ensure maximum performance it is recommended to install an air s
24. perate this tool Learn these SAFETY SYMBOLS as well as the SAFETY ALERTS to prevent injury to the operator and to bystanders r READ OPERATING INSTRUCTIONS Read and understand tool labels E safety warnings and precautions in this manual before operating the tool Failure to follow WARNINGS could result in serious injury or even death to the operator or bystanders WEAR APPROVED EYE PROTECTION Safety glasses must conform to WE the requirements of American National Standards Institute ANSI Z87 1 and provide protection against flying particles from both front and side WEAR HEARING PROTECTORS Hearing protectors should be worn to protect the ears from loud exhaust noise produced by the air tools USE ONLY CLEAN DRY COMPRESSED AIR Never use oxygen com bustible gases and any other bottled gas to operate air tools Using these other sources can cause the air tool to explode NEVER POINT THE BRAD NAILER AT YOURSELF OR OTHERS Fasteners are under extreme pressure and can cause severe injury or even death if misused DO NOT EXCEED 120 psi 8 43 kg cm G Using excessive pressure from the power source can cause the brad nailer to explode resulting in severe injury or even death to the operator or bystanders IMPORTANT INFORM ATION ABOUT THIS MANUAL Improper maintenance and operation are responsible for the majority of accidents involving brad nailers The largest portion of these could be prevented by recogniz ing the b
25. ps daily Test again if the nailer is dropped jammed etc USING THE AIR NAILER To drive a nail place the work piece contact of the brad nailer against the work piece and pull the trigger See Figure 6 To avoid any unexpected nailings perform the operation as follows 1 Avoid placing the work piece contact against the work piece with excessive force 2 Pull the trigger fully and hold it in the fired position for 1 to 2 seconds before releasing the trigger This will give the brad nailer time to complete ly expend the previous nail and build enough pressure for the next nail Figure 6 4 WARNING DO NOT hold the trigger in a half pulled position This could cause an unexpected nailing to occur if the work piece contact is permit ted to re contact the work piece Failure to comply could result in damage to work piece CHANGING DIRECTION OF EXHAUST AIR The direction of exhaust air on the air nailer can be directed 360 degrees by placing hand on exhaust cover and turning See Figure 7 Figure 7 CLEARING JAMS Typically jams are caused when a fastener or a fastener fragment becomes wedged between the driver blade and nail guide Using the wrong fastener can also cause jams TO CLEAR A JAM 1 Disconnect the air supply and remove the fastener strip Leave the pusher assembly open Figure 8 2 Pull out the latch tab and open the jam clearing door CO Remove all debris that has
26. s is fully understood before attempting to use brad nailer TO USE THE BRAD NAILER IN CONTACT ACTUATION MODE 1 Firmly grip brad nailer handle 2 Pull and hold the brad nailer trigger 3 Push brad nailer against work piece compressing work piece contact 4 The brad nailer will drive nail upon contact The brad nailer will recoil away from the work piece as nail is driven ADJUSTING DEPTH OF NAILING 4 WARNING Be aware of material thickness when using nailer A pro truding nail may cause injury Adjust the depth of nailing by turning the adjustment knob Figure 3 Item 1 to the left A for the shallowest setting and to the right B for the deepest setting To increase the depth of the nails when the adjustment knob is already set to its lowest setting increase the air pressure To decrease the depth of nails when the adjustment knob is already set to its highest setting decrease the air pressure Should nails be driven too deep even when the adjustment knob is set at its lowest setting decrease the air pressure In general the brad nailer will have a longer service life when the adjustment knob is set at a lower setting causing less wear and tear on the driving mechanism Figure 3 11 4 WARNING Always disconnect the brad nailer before making any adjustments to the nail depth knob USING THE HOOK Always disconnect the air hose before hanging the brad nailer with the hook NEVER hook the brad na
27. y or skips nails POSSIBLE CAUSE Ensure proper air pres sure is being used Inspect for worn driver blade Inspect piston O ring for wear or damage Check air pressure Ensure correct nails are being used Inspect nail feeder mechanism Piston O ring damaged or worn Nail feeder worn or damaged SOLUTION Increase air pressure Do not exceed 120 psig 8 3 bars 8 5 kg cm Contact Customer Service Reduce air pressure Use ONLY recommend ed nails Clean and lubricate nail feeder Use recommended pneumatic tool oil Contact Customer Service Replace nail feeder TROUBLESHOOTING Most minor problems can be resolved quickly and easily using the troubleshooting table below For problems that cannot be solved contact Customer Service toll free at 1 888 278 8092 PROBLEM Use ONLY recommend ed nails Contact Customer Service Replace nail feeder Ensure correct nails are being used Inspect for worn driver blade Nail feeder worn or damaged Nails jam or driven nail is bent POSSIBLE CAUSE SOLUTION Check for jammed nail Inspect nail feeder mechanism Ensure correct nails are being used Clear jammed nail Clean and lubricate nail feeder Use ONLY recommend ed nails Drives nails properly during normal nailing operations but fails to drive nails fully at faster operating speeds Nailer operates but no Switch to air hose with larger inside dia
Download Pdf Manuals
Related Search