Smith Corona 200 User's Manual
Contents
1. 16 1 Print Text From The 15 Cursor Position 2 OPC iii 16 Function Codes In WP Mode 16 TROUBLE SHOOTING 17 MAINTENANCE aaa 17 SPECIFICATION aaa 18 CONNECT POWER Power cord is located in the compartment located at the rear of the typewriter And the power switch is located on the right side of typewriter near the rear 1 Pull down the rear compartment door and connect the power cord to a proper AG outlet 2 Push the power switch to the I position When the typewriter is switched on the green LED on the keyboard will light up The carrier will move to the extreme left of the typewriter then advance to the left margin The unit is now ready for typing NOTE The Socket outlet shall be installed near the equipment and shall be easily accessible Setting When you open the printcover to change the RIBBON DAISYWHEEL CORREC TION TAPE or other reasons and if you want to re initialize your typewriter press the SETTING key 1 Open the printcover and change the RIBBON DAISYWHEEL or CORRECTION TAPE Close the printcover 2 Press the SETTING key the typewriter will then initialize itself All memories and carrier position will be maintained 4 CHANGING Changing The Ribbon Cassette 1 Move the print carrier to the center of the platen using the or z 2 Hold the ribbon cassette on both2. 11 Manual Correction 11 Word Correction 11 Correction on the Display 11 Inserting on the Display 11 3 ADVANCED OPERATION 12 AUTO Automatic Return 12 LP Line Print 12 JUST Justification 12 WORD PROCESSOR MODE 13 Pre Description 13 Memory all clear 13 File Operation 13 1 dp Direct Print 13 2 np No Print 13 so o A E A O TE 13 4 prn Print 14 5 IS Lis cities 14 6 del Delete 14 Block Operation 14 1 Mark Begin 14 2 MaK End ur 14 3 UNMAFK iii iii iaaa anaana annad e 15 4 MOVE iio apesna karorini rapia anaa 15 Sr CODY i ts 15 6 Delete 15 Edil AETA A initia 15 1 Insert Mode 15 2 Replace Mode 15 3 Correction 15 4 Delete A aaa 15 5 Cursor Movement 16 ojoj Lei EN EI O ERA PETINI 16 Print 8 Stop Code
3. WORD UNDERLINE 11 STOP 28 SEARCH 12 SETTING 29 DELETE 13 MARL MARR 30 MARK 14 TAB DECIMAL TAB 31 MOVE 15 SHFT LOCK CAPS LOCK 32 COPY 16 SHIFT 33 AUTO CENTERING 17 TAB SET TAB CLEAR 34 BOLD 35 RIGHT MARGIN FLUSH is CODE FUNCTION Hold down the CODE key and press the appro priate key to activate these functions CONTENTS CONNECT POWER ind 4 DOUING wine nid dan 4 CHANG EN Groria iieii tdi 5 Changing The Ribbon Cassette 5 Changing The Print Wheel 5 Changing The Correction Tape 6 BASIC FEATURES kivi eve 7 Selecting Pitch 7 Selecting Line Spacing 7 Setting Impression 7 Setting Margins 7 Shift and Shift Lock AAA 8 Gaps Locker 8 Special Characters 8 o ana ea ees A eee 8 Retu ainia fice citi Ai ve a 8 Relocate iii Nina plain 8 Backspacing 9 Index amp Reverse Index 9 A aa 9 A ae ears 9 WNASrINING tas ae cid 9 TABS gets cena Sec nee 10 GENIGNING uti its 10 Decimal Tab 10 Right Margin Flush 10 Checking Your Spelling Option 10 CORRECT WO Nig tests 11 Correcting One Character
4. position at which you want the printing stop The text you type after printing has stopped will be printed immediately You can continue printing the file by pressing the 0 PRINT key Function Code In WP Mode Tab Decimal Tab Indent 3 Return lt l Centering Stop File Start Fs Continuous underline Set L__ Word underline set Underline clear Bold gt Bold clear lt PA Mark LJ 16 TROUBLE SHOOTING If any operating difficulties arise check the list below before returning your typewriter for service 1 Typewriter remains at a stand with the Make sure the power cord is still power switch set to on plugged in 2 Printing is faint or does not appear Be sure the printwheel and ribbon cassette have been properly in stalled Make sure the ribbon has not been fully used 3 Corrections cannot be made Check to make sure the correction tape has been property installed Make sure the correction tape has not been fully used Make sure the correction tape has been properly selected MAINTENANCE We recommend that your typewriter be adjusted serviced and lubricated by a qualified service technician at least once a year If you need help contact your local dealer for checking your machine NOTE For best performance try to use only standard supplies from your dealer The use of non standard supplies including Ribbons Correction Tapes and Print Wheels may cause poor performan
5. spool in the clockwise direction tightening the tape until resistence is felt 5 Replace the typing ribbon cassette 6 Press the SETTING key BASIC FEATURES Selecting Pitch There are three pitches available for typing the 4 PITCH key is used to change the typing pitch When the typewriter is turned on PICA mode is selected The selection sequence is the following PICA ELITE MICRO gt PICA The chosen pitch will be displayed PICA 10 10 characters per inch ELITE 12 12 characters per inch MICRO 15 15 characters per inch Selecting Line Spacing There are three line spacing settings availble 1 1 1 2 2 The 4 LINE SPACE key is used to select line spacing The default mode is single 1 when the typewriter is turned on The selection seguence is the following 1 gt 112 gt 2 gt 1 The chosen line spacing will be displayed Setting Impression You can choose one of three hammer impression levels Light Medium and Heavy The 2 IMP key is used to set the impression level The Light level is selected initially The selection sequence is the following Light Medium Heavy Light The chosen impression level will be displayed Setting Margins You may freely adjust the margins The minimum distance between the left and right margins is one inch Left Margin Move the carrier to the desired left margin position and press the key Right Margin Move the carrier to the d
6. you press the RETURN TAB or MODE key You can type in new text while the previous line is being printed JUST Justification This mode allows you to justify a line Characters will appear on the display as you type This enables you to correct any mis typed entries on the display When you type a character over the right margin the entire line is automatically printed out justified between the left and right margin and the carrier returns to the left margin You can type new text while the previous line is being printed If you press the or key while typing on a line text will be printed out immediately and will not be justified 12 WORD PROCESSOR MODE Pre Description The WP mode will make your typing easier and more efficient Repetitive phrases terminology and entire letters can be stored edited and recalled printed at will There are six sub modes in WP mode They are dp np edit prn Is and del You can toggle between WP and TW modes by pressing the 7 TW WP key 1 dp 2 np 3 edit 4 prn 5b ls 6 del Memory All Clear When you need to make memory available for a new file and if you want to delete all contents of memory Press the Q key in TW mode If memory is broken by electric shock or mis operation press the Q key in TW mode to clear the memory File Operation 1 dp Direct Print At the main menu you can select dp mode by pressing the 1 key In this mode a new
7. ELECTRONIC TYPEWRITER Wordsmith 200 Instruction Manual Designs and specifications are subject to change without notice PARTS DESCRIPTION PLATEN KNOB PRINT CARRIER TOP COVER PAPER BAIL PLATEN POWER SWITCH I Y oa o PAPER RELEASE LEVER pat sa MET E lt D LS O nts ees SSE ED Neb eee SAY PRINT COVER KEYBOARD COVER LCD LCD CONTRAST ADJUSTER OESTE PRINT WHEEL PRINT WHEEL RELEASE LEVER PRINT WHEEL COVER RIBBON GUIDE PRINT HAMMER BRACKET RIBBON CORRECTION TAPE KEYBOARD LAYOUT 0 CO 14 2 2PM RIP 7 35 26 a j JERR s f eege a rara 16 H k v EL Li 18 19 20 1 MARGIN RELEASE 18 CODE 2 IMPRESSION SET 19 SPACE 3 LINE SPACE SET 20 CORRECTION WORD CORRECTION 4 PITCH SET 21 INDEX REVERSE INDEX 5 INDENT SET CLEAR 22 RETURN RELOCATION 6 SPELL CHECK ON OFF 23 ESC INSERT 7 TW WP MODE SET 24 CURSOR RIGHT EXPRESS 8 MODE SET 25 BACK SPACE MICRO BACKSPACE 9 STATUS 26 CONTINUOUS UNDERLINE 10 PRINT 27
8. ce or damage to your typewriter Please store your typewriter in a location protected from extreme temperatures and humidity Be sure to unplug the typewriter before cleaning and lifting it If you d like to clean your typewriter use a mild soap to remove stains Never attempt to disassemble your typewriter yourself Repairs should only be made by an autorized service technician 17 SPECIFICATION PAPER WIDTH PRINTING WIDTH DAISY WHEEL PRINTING SPEED PRINTING PITCH LINE SPACE CORRECTION MEMORY TAB BUFFER DISPLAY FILE MEMORY SPELLCHECK DIMENSION WEIGHT POWER REQUIREMENTS 12 305 mm 9 229 mm 100 spokes up to 12 cps 10 12 15 1 11 2 2 1 line 16 stops 16 characters x 2 lines 29 000 characters 50 000 words For USA UK 390 mm W 370 mm D 120 mm H 5 kg AC 120 V x 10 60 Hz AC 220 V 10 50 Hz AC 230 V 10 50 Hz AC 240 V x 10 50 Hz AC 220 V 10 60 Hz NOTE The power source is adjusted by manufacturer according to the power laticn of final destinaticn NOTE POWER CORD New Zealand Only If the electrical supply cord of this typewriter is damaged it must be replaced by the special cord SP 502 18 7301171
9. corrected 2 Press the key 3 Type the character to be corrected Word Correction Move the carrier to the end or next space position of the word to be corrected and press the key The word is then erased Correction On The Display To delete the character on the cursor position press the D DELETE key To delete the character before the cursor position press the key To delete the word before the cursor position press the key Inserting On The Display 1 Move the cursor to one character after the character to be inserted 2 Press the key Then the character indicated by the cursor will blink 3 Type the character s The character s will be inserted before the cursor 4 To exit insert mode press the CODE INSERT key again Then cursor will then change to normal state 11 ADVANCED OPERATION There are three advanced modes in your typewriter AUTO LP and JUST The mode is changed circularly when you press the 4 8 MODE key The selection se guence is following TW AUTO gt LP gt JUST TW AUTO Automatic Return Mode In this mode the carrier will automatically returned to the left margin every time the bar or the HYPHEN key is pressed in the hot zone LP Line Print Mode This mode allows you to print one line at a time Characters will appear on the display as you type This enables you to correct any mis typed entries on the display The line is printed when
10. esired right margin position and press the key Fe e Margin Release To move the carrier or type a character beyond margins press the MARGIN RELEASE key Hot Zone The hot zone starts six 6 spaces before the right margin A beep will sound when the hot zone is reached Shift and Shift Lock To type uppercase characters or symbols press either the left or right key For continuous upper case typing press the key To release the shift lock press the key Caps Lock To type the uppercase characters or lowercase symbols continuously press the CAPS key To release the caps lock press the key again Q y SHIFT or SHIFT LOCK Q CAPS LOCK 1 Q Special Characters To type the special characters marked blue press and hold down key and press the desired key Space To move the carrier or cursor forward one space press the SPACE bar Return To return the carrier or cursor to the left margin and feed paper one space press the key Relocate To move the carrier or cursor to one space after the last typed character press the CODE RELOC key Backspacing There are three different backspace function Backspace To move the carrier or cursor one space backward press the key Micro Backspace Press the key to move the carrier backward by a micro step 1 60 inch Express To move carrier or cursor to the left margin press the CODE EXPR ke
11. ext press the RETURN or CODE DEC TAB key Centering Your typewriter allows you to automatically center a line 1 Press the CENTER key The carrier will move to the center position between the left and right margins 2 Type the text The characters you type will be displayed 3 To print the text press the RETURN or DEC TAB key Right Margin Flush Your typewriter can automatically Print the text flush with the right margin 1 Press the R Right Margin Flush key The carrier will move to the right margin 2 Type the text The characters you typed will be displayed 3 To print the text press the Checking Your Spelling OPTION Your typewriter offers a spellchecker To activate the spellchecker press the 4 6 SPELL key The spellchecker will warn you when a word is mis spelled To cancel the spellcheck press the 4 6 SPELL key again 10 CORRECTION Your typewriter has a one line correction memory You can automatically correct any mis typed character within the correction memory Correcting One Character To correct the last typed character press the key The carrier will then be backspaced and the character will be erased To correct a character printed at any position on the current line move the carrier to the character to be corrected and press the key Manual Correction To correct a character beyond the correction memory 1 Move the carrier to the character to be
12. file is created and characters typed will be displayed printed and stored by pressing the or key 2 np No Print At the main menu you can select np mode by pressing the key In this mode a new file is created but not printed You can create and edit text on display only 3 edit At the main menu you can select edit mode by pressing the key In this mode characters typed are stored only in the recalled file use cursor amp RET name aaa When you want to end editing in the above modes press the key The changes you have made will be stored to the previous named file automatically The WP main menu will then be displayed 13 4 prn Print If you press the 4 key you an print a file The first file name will be displayed Press the key to select or the cursor key gt to change the file use cursor amp RET name aaa After selecting the printing file the following message will be displayed Mar Cur Sto C S If the margin format you want to use is the current format press the c key the format used when the file was created press the key And the following message will be displayed Tab Cur Sto C S If the tab stops you want to use is the current tabs press the C key the tabs used when the file was created press the key NOTE To stop printing a file press the E stop key during the printing 5 Is List If you press the key you will see the
13. list of old files To see additional windows use the cursor key lt o gt use cursor key aaa bbb 6 del Delete If you press the 6 key you can delete a file The first file name will be displayed Press the key to delete or the cursor key L gt to change the file use cursor amp RET name aaa Block Operation Block operation can be used in np or edit mode only 14 1 Mark Begin 1 Move the cursor to the beginning of the text you want to mark 2 Press the MARK key 2 Mark End 1 After having marked the beginning move the cursor to the end of the text you want to mark 2 Press the MARK key 3 Unmark If you would like to unmark previously marked text press the MARK key again 4 Move Press the MOVE key Marked text will then be inserted at the cursor positon The original text will disappear 5 Copy Press the COPY key Marked text will then be inserted at the cursor position The original text will not disappear 6 Delete Press the D DELETE key the marked text will be deleted NOTE Block function such as copy and move have no effect when the cursor is located between the start and end of block code Editor 1 Insert mode Press the key and the typewriter will switch to insert mode In this mode character will be inserted at the cursor position and remains of viewing will be moved back 2 Replace Press the key again to go back
14. sides and lift up the front portion where the ribbon is exposed to remove the cassette 3 To insert a new cassett te place the back end of the cassette on the cassette holder on the carrier and gently press down on the front of the cassette unit it clicks into place 4 Turn the ribbon feed knob counter clockwise again to take up any slack in the ribbon 5 Press the CODE SETTING key Changing The Print Wheel 1 Move the print carrier to the center of the platen using the ou 2 You will see a lever on the right side of the carrier Pull this lever toward you and lift out the daisy wheel 3 Place the daisy wheel into the slot with the characters facing the platen 4 Push the lever back into position 5 Press the SETTING key Da gt sel 5 Changing The Correction Tape 1 Move the print carrier to the center of the platen using the or 2 To replace the correction tape lift out the typing ribbon cassette see Changing The Ribbon Cassette and remove the two spools of the lift off tape by pulling them outwards 3 Place the empty spool of new tape on the left pin so that the tape winds clockwise Place the tape around the left guide Pull the tape around the right guide and place the loaded spool on the right pin so that the tape unwinds counter clockwise Make sure the sticky side of the tape is facing the platen 4 Manually turn the left hand
15. to replace mode In this mode character will be replaced at the cursor position and the cursor will advance to the next place automatically 3 Correction Press the key to delete the character before the cursor position Remains of text will shift to the left 4 Delete Press the D DELETE key to delete the character at the cursor position After the deletion the remains of the text will shift to the left If you have marked a block the block will be deleted and not the character at the cursor position 15 5 Cursor Movement e One character left e One character right e One line up e One line down e To the first column e To the end of of the current line the current line e To the start of file e To the last line of the file 6 Search To search a text press the S SEARCH key You will then be asked by the display for which text you would like to search Type the Text then press the key The display will show the first matching text after the cursor position To search next matching text press the again To quit searching press the key Print amp Stop Code 1 Print Text From The Cursor Position If you press the 0 PRINT key in np or edit mode text will be printed out from the cursor position to end of file 2 Stop Code If you want the printing of a file to stop at a specific point in the file eg to enter a name press the STOP key during the editing of the file at the
16. y Index amp Reverse Index To move the paper up half a space press the key To move the paper down half a space press the key Indent This function allows you to set a temporary indent left margin To set the indent margin move the carrier to the desired indented position and press the INDENT key To cancel the indented margin press the INDENT key again Bold To activate bold typing press the B key All characters will be highlighted To cancel press the B key again Underlining In this mode all characters will be automatically underlined Continuous Underline To activate press the key All text will automatically be underlined To cancel press the CODE U key again Word Underline To activate press the key All text except spaces will be underlined To cencel press the key again TAB To set a tab move the carrier to the desired position and press the key To clear a tab move the carrier to the tab position to be cleared and press the key To clear all tab positions press the CODE TAB C key for half a second Decimal Tab Decimal tab allows you to align numbers by decimal point at the tab position 1 Press the key The carrier will move to the next tab position 2 Type the text The characters you typed will be displayed 3 When the decimal point is typed the text will be printed out with the decimal point 4 To print the t
Download Pdf Manuals
Related Search