Home

Smeg SE365MF-5 Instructions for Installation and Use

image

Contents

1. 49 50 Instructions for the User 11 CLEANING AND MAINTENANCE Before carrying out any operations disconnect the appliance from the electricity supply Never use a jet of steam for cleaning the inside of the oven 11 1 Cleaning stainless steel To keep stainless steel in good condition it must be cleaned regularly after each use of the oven after allowing it to cool 11 2 Routine daily cleaning When cleaning and caring for stainless steel surfaces always use only specific products which do not contain abrasives or chlorine based acids Instructions for use pour the product onto a damp cloth and wipe over the surface then rinse thoroughly and dry with a soft cloth or chamois leather 11 3 Food stains or spills Never use metal scouring pads or sharp scrapers they will damage surfaces Use ordinary non abrasive products with the aid of wooden or plastic utensils if necessary Rinse thoroughly and dry with a soft cloth or chamois leather Do not allow spills of foods with high sugar content e g jam to lt dry inside the oven If they dry for too long they might damage the enamel coating of the inside of the oven me a Instructions for the User 11 4 Cleaning the oven To keep the oven in good condition it must be cleaned regularly after allowing it to cool down Remove all removable parts e Clean the oven shelves with hot water and non abrasive detergents rinse and dry For easie
2. I and X keys together To switch off the oven return all the knobs to the 0 setting in sequence 7 8 Deleting the data set With the program set keep the key of the function for deletion 55 or pressed while at the same time setting the value 0 00 by pressing the value modification keys The programmer will interpret deletion of the duration as the end of cooking 7 9 Modifying the data set The cooking data set can be modified at any moment by keeping the key of the function for modification 4 or 8 pressed and at the same time pressing the value modification keys or 41 42 Instructions for the User et 8 USING THE OVEN Before using the oven check that the display is showing the symbol see point 7 1 Setting the time 8 1 Precautions and General Advice When the oven and grill are used for the first time they should be heated to the maximum temperature for long enough to burn off any oily residues left by the manufacturing process which might contaminate foods with unpleasant smells During cooking do not cover the bottom of the oven with aluminium or tin foil and do not place pans or oven dishes on it this may damage the enamel coating If you wish to use greaseproof paper position it so that it does not interfere with the hot air circulation inside the oven Oven accessories which may come into contact with foods are made from materials compliant with EEC directive 89
3. 2 190 60 RICE CAKE 1 2 180 60 orm PLI PLA m GRILLING wy wv RUNNER POSITION TIME IN MINUTES FROM THE BOTTOM 1ST SIDE 2ND SIDE PORK CHOP 4 7 9 5 7 PORK FILLET 3 9 11 5 9 FILLET STEAK 3 9 11 9 11 SLICED LIVER 4 2 3 2 3 VEAL ESCALOPES 4 7 9 5 7 HALF CHICKEN 3 9 14 9 11 SAUSAGE 4 7 9 5 6 MEATBALLS 4 7 9 5 6 FISH FILLET 4 5 6 3 4 TOASTED SANDWICHES 4 2 4 2 3 48 PASTA LASAGNE PASTA BAKES CREOLE RICE MEAT ROAST VEAL ROAST PORK ROAST BEEF FILLET STEAK ROAST LAMB RARE ROAST BEEF ROAST CHICKEN ROAST DUCK ROAST TURKEY ROAST RABBIT ROAST HARE ROAST PIGEON FISH PIZZA BREAD TOASTED SANDWICHES CONFECTIONERY SPONGE CAKE FRUIT CAKE CROISSANTS PASTRY RICE CAKE APPLE CAKE ANGEL CAKE Instructions for the User A 2 HOT AIR COOKING RUNNER POSITION FROM THE BOTTOM 2 2 2 1 1 1 1 UW o T IMMISIT 1 00 CO CO TEMPERATURE C 190 210 190 210 190 210 150 170 150 160 160 170 160 180 130 150 170 180 170 160 170 150 160 150 160 160 170 140 170 150 170 210 240 190 210 220 240 150 160 150 160 150 160 150 160 150 160 150 160 150 160 TIME IN MINUTES 20 25 25 30 20 25 65 90 70 100 65 90 35 45 100 130 40 45 70 90 100 160 160 240 80 100 30 50 15 25 Depending on size 30 50 40 35 45 40 50 40 60 25 65 65 65
4. just one part of the appliance and the use of non original spare parts Instructions for the User 4 GET TO KNOW YOUR OVEN i g CONTROL PANEL EJ OVEN LIGHT HOT AIR FAN ON SOME MODELS ONLY 4 SHELF AND TRAY RUNNERS 5 BEFORE INSTALLATION Never leave packaging residues unattended in the home Separate waste packaging materials by type and consign them to the nearest separate disposal centre The inside of the appliance should be cleaned to remove all manufacturing residues For further information see 11 CLEANING AND MAINTENANCE When the oven and grill are used for the first time they should be heated to the maximum temperature for long enough to burn off any oily residues left by the manufacturing process which might contaminate foods with unpleasant smells After an interruption in the electricity supply the programmer display flashes at regular intervals showing 0 00 For setting instructions see point 7 ELECTRONIC PROGRAMMER 35 Instructions for the User 6 DESCRIPTION OF FRONT PANEL CONTROLS All the cooker s control and monitoring devices are placed together on the front panel The table below provides the key to the symbols used 36 m o ome Instructions for the User THERMOSTAT KNOB The cooking temperature is selected by turning the knob clockwise to the value required betw
5. of the frame fig 1 For installation under tops make sure that the rear bottom of the unit has an opening similar to that shown in figure 1 ref B See the instructions supplied with the hob for the relative positioning and fixing procedures m Misure fornite in mm 80 90 989 89 583 585 572 595 583 585 21 560 57 58 Instructions for the Installer Never use the door for leverage when inserting the oven in the cabinet Never apply excessive pressure to the open door 13 3 Hob oven connection Once installed the combined hob must be connected to the oven Fit the oven into the built in installation opening leaving enough room to carry out the operations described below connect the yellow green earth wire of the hob to the oven s earth terminal A see figure connect the hob connectors to the sockets provided on the top casing of the oven The colours and symbols of the connectors must correspond to those on the oven sockets if the hob has a residual heat warning device connector connect it to the unused socket on the right hand side At this point the oven can be completely built into the cabinet taking care to place the power supply lead along the best possible route and ensuring that it is not touching hot parts
6. smaller diameter areas To regulate the heating level turn the knob anti clockwise to the setting required To return to heating of the smaller diameter area only turn the knob to 0 and then to between 2 and 12 IMPORTANT ON MODELS WITH INTEGRATED CONTROLS To access the control knobs they must first be extracted simply press them and they will spring out into the operating position on their own Fig A They must remain in this position as long as the oven is in operation as otherwise they may overheat To return them to the rest position press them right down until the catch engages To open the oven door the handle must first be extracted simply press it and it will spring out into the right position Fig B It must remain in this position as long as the oven is in operation as otherwise it may overheat 38 evt Instructions for the User 7 ELECTRONIC PROGRAMMER 12 3 0 X 9 323 23 2302 LIST OF FUNCTIONS MINUTE MINDER BUTTON D L _ COOKING DURATION BUTTON END OF COOKING BUTTON VALUE DECREASE BUTTON VALUE INCREASE BUTTON Ili MANUAL MODE BUTTON 7 1 Setting the time When the oven is used for the first time or after an interruption in the electricity supply the display flashes at regular intervals showing 0 00 Press to stop the display flashing Press the value modification keys or within 5 seconds to increase or decrease the setting by one minute for ea
7. 109 of 21 12 88 and national relevant regulations To avoid unpleasant contact with any steam inside the oven open the door in two stages hold it open just a little about 5 cm for 4 5 seconds then open it completely If you have to check or carry out other procedures on food during cooking leave the door open for as short a time as possible to prevent a drop in the oven temperature which will impair the cooking results When the door is opened the oven s internal fan cuts out automatically it starts up again when the door is closed amp me Instructions for the User 8 2 Cooling fan system on some models only The appliance is equipped with a cooling system which comes into operation a few minutes after the oven is switched on The operation of the fans generates a normal air flow which comes out above Fig 1 or below Fig 2 the door depending on the model and may continue for a short time even after the oven is switched off 1 2 8 3 Inside light Depending on models Depending on the model the oven light switches on when the oven door is opened or when function knob is turned to any function or e when the function knob is turned to the xx symbol 43 44 Instructions for the User 9 ACCESSORIES AVAILABLE The oven is fitted with 4 runners for placing trays and shelves at different heights
8. ECTOR wy Z THERMOSTAT 50 250 C This system is suitable for cooking on several shelves even with foods of different kinds fish meat etc without cross contamination of flavours or smells The air circulation inside the oven ensures uniform heat distribution Multiple cooking is possible provided that all foods require the same temperature 45 Instructions for the User me 10 3 Delicate cooking FUNCTION SELECTOR w THERMOSTAT 50 250 C This type of cooking for which it is extremely important to preheat the oven in fan mode is particularly suitable for finishing cooking of foods underneath or for processes which require heat mainly from below The tray should be placed on the bottom runner 10 4 Grilling PAL a FUNCTION SELECTOR tg THERMOSTAT 250 Used for quick browning of foods For short processes and small amounts 2 place the shelf on the fourth runner from the bottom For longer cooking times and grilling place the shelf on lower runners depending on the size of the food Keep the door closed during grilling Grilling with the door open may permanently damage the oven and reduce operating safety 10 5 Hot air grilling FUNCTION SELECTOR wy G THERMOSTAT 200 C Allows uniform heat distribution with better penetration to the core of foods Foods are lightly browned on the outside but still soft on the inside During cooking the oven door must be closed and the maxim
9. NDED FOR HOUSEHOLD USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE THE APPLIANCE IS BUILT TO PROVIDE THE FOLLOWING FUNCTION COOKING AND HEATING FOODS ALL OTHER USES ARE TO BE CONSIDERED IMPROPER THE MANUFACTURER DECLINES ALL LIABILITY FOR USES OTHER THAN THOSE STATED ABOVE NEVER USE THIS APPLIANCE FOR HEATING ROOMS NEVER USE PACKAGING RESIDUES UNATTENDED IN THE HOME SEPARATE THE VARIOUS PACKAGING MATERIALS BY TYPE AND CONSIGN THEM TO THE NEAREST SEPARATE DISPOSAL CENTRE THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002 96 EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT WEEE THIS GUIDELINE IS THE FRAME OF A EUROPEAN WIDE VALIDITY OF RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT NEVER OBSTRUCT THE OPENINGS AND SLITS PROVIDED FOR VENTILATION AND HEAT DISPERSAL THE NAMEPLATE WITH THE TECHNICAL DATA SERIAL NUMBER AND MARK ARE IN A VISIBLE POSITION ON THE OVEN DOOR FRAME THE NAMEPLATE MUST NEVER BE REMOVED NEVER USE METAL SCOURING PADS OR SHARP SCRAPERS THEY WILL DAMAGE SURFACES USE ORDINARY NON ABRASIVE PRODUCTS WITH THE AID OF WOODEN OR PLASTIC UTENSILS IF NECESSARY RINSE THOROUGHLY AND DRY WITH A SOFT CLOTH OR CHAMOIS LEATHER DO NOT ALLOW SPILLS OF FOODS WITH HIGH SUGAR CONTENT E G JAM TO DRY INSIDE THE OVEN IF THEY DRY FOR TOO LONG THEY MIGHT DAMAGE THE ENAMEL COATING OF THE INSIDE OF THE OVEN Disposal instructions 2 DISPOSAL INSTRUCTIONS OUR ENVI
10. RONMENT POLICY Our products are only packaged using non pollutant environment friendly recyclable materials We urge you to cooperate by disposing of the packaging properly Contact your local dealer or the competent local organisations for the addresses of collection recycling and disposal facilities Never leave all or part of the packaging lying around Packaging parts and especially plastic bags may represent a suffocation hazard for children Your old appliance must also be disposed of properly Important deliver the appliance to your local organisation authorised to collect scrapped appliances Proper disposal allows the intelligent recovery of valuable materials Before scrapping your appliance it is important to remove doors and leave shelves in position as for use to ensure that children cannot accidentally become trapped inside the oven during play Also cut the power supply lead and remove it and the plug 33 34 Safety Precautions 3 SAFETY PRECAUTIONS SEE INSTALLATION INSTRUCTIONS FOR SAFETY REGULATIONS FOR ELECTRIC OR GAS APPLIANCES AND FOR VENTILATION FUNCTIONS IN YOUR INTEREST AND TO ENSURE YOUR SAFETY BY LAW ALL ELECTRIC APPLIANCES MUST ONLY BE INSTALLED AND SERVICED BY QUALIFIED STAFF IN ACCORDANCE WITH THE RELEVANT REGULATIONS OUR APPROVED INSTALLATION ENGINEERS GUARANTEE YOU A JOB WELL DONE GAS OR ELECTRIC APPLIANCES MUST ALWAYS BE DISCONNECTED BY SUITABLY SKILLED PEOPLE THE PLUG
11. Shelf useful to support pans containing the food for cooking Tray grid for placing on top of a tray for cooking foods which may drip Oven tray useful for collecting fat from foods placed on the grid above Pastry tray useful for cooking cakes pizza and confectionery Roof liner remove it to simplify cleaning inside the oven Chromium plated gripper useful for removing hot shelves and trays Not all accessories are provided on some models Optional accessories Original accessories can be ordered through our Authorised Service Centres me Instructions for the User 10 COOKING ADVICE The oven should always be preheated in fan mode to 30 40 C above the cooking temperature This considerably shortens cooking times and reduces electricity consumption as well as giving better results The oven door must be closed during cooking operations 10 1 Conventional cooking Ed ed FUNCTION SELECTOR 7 THERMOSTAT 50 250 C This conventional cooking method with heat from above and below is suitable for cooking food on just one shelf The oven must be preheated to the chosen temperature Do not place the food in the oven until the thermostat light goes out Place frozen meat in the oven directly without thawing The only precaution required is to set temperatures about 20 C lower and cooking times about 1 4 longer than for fresh meat 10 2 Hot air cooking PE ae CES FUNCTION SEL
12. TO BE CONNECTED TO THE POWER SUPPLY LEAD AND THE RELATIVE SOCKET MUST BE OF THE SAME TYPE AND COMPLY WITH THE RELEVANT REGULATIONS THE POWER SUPPLY SOCKET MUST BE ACCESSIBLE EVEN AFTER THE APPLIANCE HAS BEEN BUILT IN NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY REGULATIONS IMMEDIATELY AFTER INSTALLATION CARRY OUT A QUICK TEST ON THE APPLIANCE FOLLOWING THE INSTRUCTIONS PROVIDED LATER IN THIS MANUAL IF THE APPLIANCE FAILS TO OPERATE DISCONNECT IT FROM THE ELECTRICAL MAINS AND CONTACT YOUR NEAREST SERVICE CENTRE NEVER ATTEMPT TO REPAIR THE APPLIANCE NEVER PLACE FLAMMABLE OBJECTS IN THE OVEN IF IT SHOULD ACCIDENTALLY BE SWITCHED ON THIS MIGHT CAUSE A FIRE THE APPLIANCE BECOMES VERY HOT DURING USE TAKE CARE NOT TO TOUCH THE HEATING ELEMENTS INSIDE THE OVEN THE APPLIANCE IS INTENDED FOR USE BY ADULTS KEEP CHILDREN AT A SAFE DISTANCE AND NEVER ALLOW THEM TO PLAY WITH IT WHEN THE GRILL IS IN OPERATION ACCESSIBLE PARTS MAY BECOME VERY HOT KEEP CHILDREN AT A SAFE DISTANCE BEFORE THE APPLIANCE IS PUT INTO OPERATION ALL THE LABELS AND PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED AFTER EACH USE ALWAYS CHECK THAT THE CONTROL KNOBS ARE TURNED TO 0 OFF The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even
13. Table of Contents 1 PRECAUTIONS FOR USE eee emere 32 2 DISPOSAL INSTRUCTIONS OUR ENVIRONMENT POLICY 33 3 SAFETY PRECAUTIONS da ite err rette cepa etiain 34 4 GET TO KNOW YOUR 35 5 BEFORE INSTALLATION eene 35 6 DESCRIPTION OF FRONT PANEL CONTROLS 36 7 ELECTRONIC PROGRAMMER eee emen 39 85 USING THE OVEN eese ester be e E ER nce eats 42 9 ACCESSORIES AVAILABLE eee 44 10 COOKING ADVICE oer Ete ite Pese tesa tus 45 11 CLEANING AND MAINTENANCE eee e 50 12 EXTRAORDINARY MAINTENANCE eee 53 13 INSTALLING THE APPLIANCE 55 INSTRUCTIONS FOR THE USER these provide recommendations for me use a description of the controls and the correct procedures for cleaning and maintaining the appliance INSTRUCTIONS FOR THE INSTALLER these are intended for the qualified engineer who is to install commission and test the appliance 31 32 Precautions for Use 1 PRECAUTIONS FOR USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE OVEN S LIFE CYCLE WE URGE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE APPLIANCE INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE RELEVANT REGULATIONS THIS APPLIANCE IS INTE
14. ch pressure Press one of the two value modification keys until the current time appears Before each programmer setting switch on the function and set the temperature required 39 40 Instructions for the User me 7 2 Semiautomatic cooking This function only switches the oven off automatically at the end of the cooking time Press the Jf key and the display will light up showing the figures 0 00 keep it pressed and at the same time use the value modification keys or to set the cooking duration A few seconds after the 9 key is released the count of the programmed cooking duration will start and the display will show the current time together with the symbols and 8 7 3 Automatic cooking This function switches the oven on and off in fully automatic mode Press the Jf key and the display will light up showing the figures 0 00 keep it pressed and at the same time use the value modification keys or to set the cooking duration Press the 9f key and the display will show the sum of the current time plus the cooking duration just set keep it pressed and at the same time use the value modification keys or to adjust the end of cooking time A few seconds after the key is released the programmed count will start and the display will show the current time together with the symbol A When the cooking start time calculated automatically by the programmer on the basis of the data entered is reached
15. een 50 and 250 C In the model with glass front panel the maximum temperature is 260 C rs Mot oxi FUNCTION SELECTOR KNOB Turn the knob either way to select one of the following functions 3m x NO FUNCTION SET Ja THAWING INSIDE LIGHT NO HEATING TOP BOTTOM HEATING ELEMENTS ON wy ELEMENTS FAN lt TOP BOTTOM HEATING ooze GRILL ELEMENT FAN ELEMENTS wy GRILL ELEMENT IN OPERATION FAN HEATING ELEMENT ALTERNATING WITH BOTTOM HEATING ELEMENT FAN GRILL ELEMENT i Li a SMALL GRILL ELEMENT FAN wy BOTTOM HEATING ELEMENT BOTTOM HEATING ELEMENT wy FAN 4 TOP BOTTOM HEATING ELEMENTS FAN HEATING ELEMENT 37 BIE Instructions for the User ent THERMOSTAT LIGHT to indicate that the oven is heating up Goes out when the set temperature is reached flashes at regular intervals to indicate that the D temperature inside the oven is being kept constantly at the set level HOB CONTROL KNOB Used to regulate heating of the hob by turning the knob clockwise to the required setting between 2 and 12 DUAL HEATING HOB CONTROL KNOB Used to regulate heating of the hob in dual heating zones Turning the knob 0 9 clockwise to between 2 and 12 heats 3 S 1 only the smaller diameter area Turning uf the knob 846 m to the or symbol and releasing it it returns to 12 heats both the larger and
16. ith a damp sponge and ordinary detergent Instructions for the Installer 12 EXTRAORDINARY MAINTENANCE Occasionally the oven will require minor servicing procedures or the replacement of parts subject to wear and tear such as gaskets light bulbs etc The specific operations for each procedure of this kind are provided below Before carrying out any operation involving access to live parts disconnect the appliance from the electricity supply 12 1 Changing the light bulb Remove the protective cover A by unscrewing it anti clockwise and replace the bulb B with another of the same type 25 W Replace the protective cover A Use only light bulbs approved for ovens T 300 C 8 function model with glass front panel The standard light bulbs are of halogen type do not touch them with your fingers wrap them in an insulating material Use only light bulbs available from our Authorised Service Centres 53 54 Instructions for the Installer 12 2 Removing the door Lift the levers B and take hold of the two sides of the door with both hands close to the hinges A Raise the door to an angle of about 45 and remove it To reassemble fit the hinges A into their grooves then lower the door into place and engage the levers B 12 3 Removing the gasket To allow thorough cleaning of the oven the door gasket can be removed Before removing the gasket remove the oven door as described above Once the door has bee
17. n removed lift the tangs at the corners as shown in the figure Instructions for the Installer 13 INSTALLING THE APPLIANCE 13 1 Electrical connection j The nameplate with the technical data serial number and mark is in a J visible position on the oven door frame The nameplate must never be removed The appliance must be connected to earth in compliance with electrical system safety regulations If a permanent connection is used the appliance s power supply line must be fitted with an omnipolar breaking device with contact gap of at least 3 mm located in an easily accessible position close to the appliance itself If a socket and plug connection is used check that they are of the same type Do not use reducers adapters or junctions since they may cause overheating or burns Operation at 220 240 V use a 1 5 mm HO5RR F three wire cable cable of 3 x 1 5 The earth wire yellow green 20 mm must be at least 20 mm longer than the other wires at the end for connection to the appliance 55 56 Instructions for the Installer 13 1 1 Ovens with hob controls On ovens with hob controls the power supply lead is not supplied Use HO5RR F or HO5RN F rubber cable and when positioning it ensure that it does not touch the metal parts of the appliance s external casing To access the terminal board remove the appliance s back cover by unscrewing the relative screws If necessary cha
18. nge the positions of the jumpers on the terminal board as shown then connect the wires making sure that the earth wire is at least 20 mm longer Fix the power supply lead to the appliance using the cable clamp provided Operation at 220 240 V use a 220 240V HO5RR F HO5HN F three wire cable cable of 3 x 4 mn eS 20 Operation at 380 415V2N use a 380 415V2N TE HO5RR F HO5HRHN F four wire cable cable of 4 x 2 5 mm q 20 mm Operation at 380 415V3N use HOSRR F HOSRN F five wire cable 380 415V3N 5mm cable of 5 x 1 5 mn The earth wire yellow green must be at 20 mm least 20 mm longer than the other wires at the end for connection to the appliance Instructions for the Installer 13 2 Positioning the oven The appliance is designed for building in to cabinets made from any heat resistant material Comply with the dimensions shown in figures 1 2 and 3 When installing under worktops comply with the dimensions shown in figure 1 3 When installing under worktops incorporating combined hobs a gap of at least 110 mm must be left from any side wall as shown in figure 1 When installing in tall units comply with the dimensions shown in figure 1 2 bearing in mind that the top rear of the unit must have an opening 80 90 mm deep Screw the 4 screws A into the inside
19. r cleaning the door can be removed see point 12 2 Removing the door 11 5 Cleaning the oven with self cleaning liners on some models only The oven is fitted with enamelled liners that are continuously self cleaning These liners simplify cleaning of the oven and ensure it continues to perform well over time 11 5 1 Using the self cleaning liners To keep the inside of the oven clean and free from food residues and unpleasant smells it should periodically be operated empty at a temperature of at least 200 C for a time varying between 30 and 60 minutes This allows the self cleaning liners to oxidise any deposits present which can then be wiped away with a damp sponge once the oven has cooled 11 5 2 Maintenance of self cleaning liners The liners should not be cleaned using abrasive creams and ordinary cleaners Simply wipe with a damp sponge to avoid damaging the special enamel coating 51 52 Instructions for the User evt 11 5 3 Removing the self cleaning liners Remove all accessories from the inside of the oven and proceed as follows 1 Remove the side runners fig 1 2 Extract the side liners F and G fig 2 3 Extract the back liner A after undoing the threaded ring nut fig 2 4 Replace the liners in their original positions b 11 6 Cleaning the door glazing The glass in the door should always be kept thoroughly clean Use absorbent kitchen roll remove stubborn dirt w
20. the display will show the A and 9 symbols together After the setting to view the cooking time left press the key to view the end of cooking time press the Y key The logic prevents the setting of incompatible values e g the programmer will not accept an end of cooking time with a duration which is too long for this value 7 4 Minute minder The programmer can also be used as an ordinary minute minder Press the f key and the display will show the figures 0 00 keep it pressed and simultaneously press the value modification keys or When the key is released the programmed count will start and the display will show the current time and the symbol GNK Instructions for the User After the setting to display the time left press the key In minute minder mode the system will not cut out operation of the oven at the end of the set time 7 5 End of cooking At the end of the cooking time the oven will switch off automatically and simultaneously a buzzer will start to sound in on off mode After the buzzer is stopped the display will return to showing the current time together with the 3 symbol indicating that the oven is again ready for use in manual mode 7 6 Adjusting the buzzer volume The buzzer volume can be varied 3 settings while it is in operation by pressing 7 7 Stopping the buzzer The buzzer stops automatically after seven minutes It can be stopped in manual mode by pressing the
21. um heating time must not exceed 60 minutes 46 Cea Instructions for the User Keep the door closed during grilling Grilling with the door open may AN permanently damage the oven and reduce operating safety 10 6 Thawing 2 71e 2 e FUNCTION SELECTOR oes THERMOSTAT 0 The air movement provided by the hot air fan alone thaws foods more quickly The air circulating inside the oven is at room temperature Thawing at room temperature has the advantage that the food s flavour and appearance are retained intact 47 GB IE A Instructions for the User oN 10 7 Recommended cooking tables Cooking times for meat in particular vary depending on the food s thickness and quality and personal preference All times are calculated with the oven preheated CONVENTIONAL COOKING wwe RUNNER POSITION FROM TEMPERATURE TIME IN MINUTES THE BOTTOM C PASTA LASAGNE 2 3 210 230 30 PASTA BAKES 2 3 210 230 40 MEAT ROAST VEAL 2 170 200 30 40 PER kg ROAST BEEF 2 210 240 30 40 PER kg ROAST PORK 2 170 200 30 40 PER kg CHICKEN 2 170 200 45 60 DUCK 2 170 200 45 60 GOOSE TURKEY 2 140 170 45 60 RABBIT 2 170 200 50 60 LEG OF LAMB 2 170 200 40 50 FISH 1 2 170 200 Depending on size PIZZA 1 2 210 240 40 45 CONFECTIONERY PASTRY 1 2 170 200 15 20 SPONGE CAKE 1 2 165 35 45 CROISSANTS 1 2 170 200 40 45 FRUIT CAKE 1 2 170 200 20 30 ANGEL CAKE 1 2 170 60 APPLE CAKE 1

Download Pdf Manuals

image

Related Search

Related Contents

Quick Start Guide - AC Lighting Inc.  User's Guide to the Camel Citator  Philips Bulb 925693945503  LV52P3/LV32P3 - Quest International  FloBoss 503 and 504 Instruction Manual  User Guide - Cobra  Portero convencional 4+n  "user manual"  Visio-900-0131-02-00 Rev A.vsd  第5回会報  

Copyright © All rights reserved.
Failed to retrieve file