Smeg PTS605NU3 Instruction Manual
Contents
1. Fig 1 Fig 3 Fig 5 CEN Conversion Kit 4 To adjust the cooktop for LP gas or to return to Natural Gas use refer to the tables below Central Rear Rear Central Central central a Central Front Front PTS605U Natural gas PTS605U LP o km O bew o ye Left Central o e oa Left Central 14000 1 10 ae a ee SEMEN ana 1 05 SOME ena 0 73 1800 0 37 Rear Rear cema 900 128 ee ee ee ee ee PTS727U Natural gas PTS727U LP ane ene On S00 Lett Central 3000 aa o d o Inner Inner Central 3400 0 80 1500 See aug 0 54 1500 0 33 Front Front Right Front 0 80 Right Front 3400 0 54 1500 0 33 37 NOTE Save the nozzles removed from the appliance for future use Conversion Kit Remove the screw A and push the support B fully down Remove the nozzle C with a wrench and insert the suitable nozzle following the instructions in the tables referring to the type of gas to be used The nozzle must not be tightened with a torque of more than 3 Nm Return the support B to its original position so that the nozzle C is perfectly covered Regulate the air flow by moving the Venturi pipe D until the distance X stated in point 5 5 Adjusting the primary air flow is obtained and secure it with screw A When theadjustments are complete restore the seals with wax or a similar material 5 Referring to distance X in mm PTS605U Natural gas PT2. gas connections for leaks Bubbles around connections indicate a leak If a leak appears shut off gas valve controls and adjust the connections Then check the connections again NEVER TEST FOR GAS LEAKS WITH A MATCH OR OTHER FLAMES Remove all of the detergent solution from the cooktop Electronic Ignition System initial lighting 7 Cooktop burners use electronic igniters rather than standing pilots When the cooktop control fae knob is pushed in and turned to the minimum flame ANI position the system creates a spark Z to ignite the burner This sparking continues until the control knob is turned to the desired setting Check the operation of the cooktop burners Push in and turn each control knob to the maximum flame position N The flame should light within 4 seconds If the burners do not light properly turn the control knob to the O position Ensure that the burner cap is in the proper position Check that the power supply cord is plugged in and that the circuit breaker or house fuse has not blown Make sure that the shut off valve is on the ON position Check operation again If a burner does not light at this point contact your SMEG dealer for assistance Replace the components on the burner and turn the knobs on the gas tap pins Light the burner and set it at minumum Remove the knob and turn the regulation screw next to the gas tap pin until you obtain a suitable minimum flame Replace the knob and check flame st
3. Important Safety Instruction IMPORTANT SAFETY INSTRUCTIONS We have provided many important safety messages throughout this manual and on the appliance READ AND SAVE THESE INSTRUCTIONS Your safety and the safety of others are very important Read all instructions before using the appliance and always obey all safety messages RECOGNIZE SAFETY INFORMATION This is a safety alert symbol This symbol alerts you to potential hazards that can kill or hurt you and others UNDERSTAND SIGNAL WORDS A signal word DANGER WARNING or CAUTION is used with the safety alert symbol DANGER identifies the most serious hazards It means you can be killed or seriously injured if you do not immediately follow the instructions WARNING means you can be killed or seriously injured if you do not follow the instructions CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury All safety messages will inform you of potential hazards on how to reduce the risk of injury and what can occur if the instructions are not followed IMPORTANT Observe all governing codes and ordinances WARNING For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage personal injury or death This conversion kit must be installed by a qualified service agency in accordance with the manufacturer s instructions and all applicable co
4. S605U LP Air Shutter Air Shutter Left Central 2 3 7 0 mm Left Central 1 3 12 0 mm Central Front 2 3 7 0 mm Central Front 2 3 7 0 mm Central Rear 2 3 7 0 mm Central Rear 2 3 7 0 mm Right Central 3 44 4 0 mm Right Central 3 3 10 0 mm 6 PTS727U Natural gas PTS727U LP Air Shutter Air Shutter Left Inner 3 8 10 0 mm Left Inner 7 3 7 0 mm Central Outer 3 3 10 0 mm Central Outer 1 3 12 0 mm Central Front 2 3 7 0 mm Central Front 2 3 7 0 mm Central Rear 3 3 7 0 mm Central Rear 213 7 0 mm Right Front 2 3 7 0 mm Right Front 2 3 7 0 mm Right Rear 3 46 4 0 mm Right Rear 3 3 10 0 mm After carrying out the above adjustments remount in reverse order to the instructions given in point 3 7 Caution refit all flame caps in the same points from which they were removed In fact the flame cap positions cannot be changed After refitting them ensure that they are perfectly positioned and that there is no clearance between the cooktop and the flame caps FIRE HAZARD A WARNING Failure to follow this instruction can result in death or fire Use a soapy solution to check for proper tightness X Never test for gas leaks with a match or other flames 8 9 10 11 12 13 14 Conversion Kit Leak testing of the appliance must be conducted according to the following instructions Use a brush and liquid detergent to test all
5. ability by rapidly turning the knob from maximum to minimum The flame should not go out Check flame at the maximum flame position ANI for a blue color It should be clean and soft in character No blowing or lifting of flame should occur Occasional orange flashes are normal and reflect different elements in the air or gas Completely fill out the conversion label part no 92849A078 and attach the label to the bottom of the cooktop beside the ID tag Do not cover the ID tag with the conversion label At higher altitudes no further adjustments are necessary Derating the burners is also unnecessary Save the nozzles removed from the unit along with these instructions for possible future use NATURAL GAS To convert back to Natural Gas Follow steps 3 through 11 and replace the nozzles in the order in which they were removed
6. des and requirements of the authority having jurisdiction The qualified service agency is responsible for the proper installation of this kit The installation must not be considered to be correct and completed until the operation of the converted appliance is checked as specified in the manufacturer s instructions supplied with this kit FIRE HAZARD Securely tighten all gas connections If connected to LP have a qualified person ensure that the gas pressure does not exceed 14 water column Examples of a qualified person include licensed heating personnel authorized gas company personnel and authorized service personnel FAILURE TO DO SO CAN RESULT IN DEATH EXPLOSION OR FIRE 1 2 Check that the main gas supply line to the cooktop is shut off and that the power supply cord is disconnected Conversion Kit To Cooktop Shutoff Valve open position Gas Supply Line Remove access cap A by using a screwdriver or a quarter turning the access cap counter clockwise The gas pressure regulator has two settings which are indicated on two sides of the cap Turn the cap and reinstall it in the regulator with LP visible from the outside of the regulator The regulator must be checked at a minimum water column of 1 inch 2 5 cm above the set pressure The inlet pressure to the regulator should be as follows for operation and checking the regulator setting NATURAL GAS S
7. et pressure at 6 W C Supply pressure of 3 1 2 10 ye W C maximum LP GAS Set pressure at 10 W C Supply pressure of 8 13 W C maximum The cooktop must be isolated from the gas supply piping system by closing the respective manual shut off valve during any pressure testing of the gas supply piping system at test pressures equal to or greater than 1 2 psig 3 5 kPa 3 Conversion Kit CEN Remove all the burner components in the numerical order shown below Remove the pan stands Fig 1 by lifting them from the back 1 and extracting them 2 On 70 cm cooktops remove the central pan stand first on 60 cm cooktops the right hand pan stand must be removed first remove all the knobs 3 Fig 2 by pulling them outward lift all the burner components off the cooktop 4 5 Pic 2 use the wrench 6 Fig 3 to open the bayonet fastenings of the burner fixing rings applying leverage on the guides 7 after removing all the components described above lift the front of the cooktop s upper surface 8 Fig 4 the burners and gas taps can only be accessed by pushing the rear of the cooktop gently upwards with the aid of a tool 9 10 Fig 5 This is necessary to release the internal snap fixing devices The cooktop s upper surface can now be removed Some models may have 2 additional pins at the side Fig 5 which must be removed in the same way using a tool to apply leverage to the cooktop
Download Pdf Manuals
Related Search