Smeg PA106SX Instructions for Installation and Use
Contents
1. 8 mm 8 mm gt gt lt 8mm lt q 22 mm 22 mm F Yz Es FE LZ A MOD 60 MOD 70 MOD 100 The diagram below shows the exact positions of the holes to be used for clamping the hob to the top correctly z o VO Overall dimensions location of gas and electrical connection points all measures in mm 595 60 cm hobs 60cm 70cm 100cm 715 70 cm hobs hob hob hobs 1005 100cm hobs A A5 105 105 B 290 340 470 C 45 45 45 D 45 45 65 500 Instructions for the installer 2 2 Clearance above and around domestic appliances Extract from AS5601 THE TWO INSETS RELATE TO REQUIREMENT 3 BELOW Horizontal combustible surface below hob B D Wa d Ji Je G DT cd E L Horizontal combustible surface above trivet NOTE in this case any P vertical combustible p surface needs to be protected to conform with requirement 2 below REQUIREMENTS Overhead clearances Measurement A Range hoods and exh2. TO CARRY OUT THE FOLLOWING FUNCTIONS COOKING AND HEATING UP OF FOOD ALL OTHER USES ARE CONSIDERED IMPROPER THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER USE DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT SEPARATE THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST SPECIAL GARBAGE COLLECTION CENTRE IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES THE PLUG TO BE CONNECTED TO THE POWER CABLE AND THE SOCKET MUST BE THE SAME TYPE AND MUST CONFORM TO CURRENT REGULATIONS NEVER UNPLUG BY PULLING ON THE CABLE IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST OF THE COOKING HOB FOLLOWING THE INSTRUCTIONS BELOW SHOULD THE APPLIANCE NOT FUNCTION DISCONNECT IT FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE NEVER ATTEMPT TO REPAIR THE APPLIANCE ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION ZERO OFF WHEN YOU FINISH USING THE HOB THE IDENTIFICATION PLATE WITH TECHNICAL DATA SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING THE PLATE ON THE CASING MUST NOT BE REMOVED A COPY OF THE PLATE IS ENCLOSED WITH THIS BOOKLET AND SHOULD BE STICKED IN THE FRAME IN THE INNER COVER BEFORE CONNECTING THE DEVICE MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS ON THE COOKING HOB GRIDS um m d Introduction
3. lift up one of the horizontal spokes of the grid to remove it from its housing Clean these parts with a fine abrasive sponge or similar products found on the market Then redo with SS specific polish to make the steel shiny Reassemble the burner caps on their flame crowns When replacing the grids make sure that pins C are aligned with their seats on the hob then press them in with the palm of your hand until they lock in place 9 2 3 Flame crowns The flame crowns are removable Wash them with hot water and non abrasive detergent Be careful to remove all deposits When you replace them make sure that they are completely dry and inserted correctly in their housings See Section 8 Using the hob Instructions for the user 9 2 4 Ignition plugs and safety devices For good functioning of the ignition plugs and the safety devices keep them very Clean Check frequently and clean with a damp cloth when necessary 9 3 Preventive maintenance This appliance does not need any special maintenance However a few simple gt operations have to be carried out periodically to prevent malfunctioning Burners the burners must be cleaned periodically once a year to ensure correct combustion make sure that all the openings and flame ports are clean and free of obstacles and that the burners rest firmly on their supports Gas connection the gas connection must be checked periodically every 2 years
4. should not go out Instructions for the installer 6 3 Arrangement of the burners on the hob g alg a 7 Zeie Q E A D 3 A d A E CN a d p 9 BURNERS Auxiliary Medium a a Nodes UR Le a af P wm Semi rapid rapid Large rapid If the flame of the UR burners have unstable flame the ring does not ignite or has difficulty igniting clean the perforated ring carefully to remove any residues deposited in the holes persists after this cleaning contact an authorised service centre 6 4 Lubrication of gas taps With time it may happen that the gas taps get blocked and hard to turn Clean them inside and re grease them This operation must be done by an authorised person If the problem 15 16 Instructions for the user ome 7 DESCRIPTION OF THE CONTROLS 7 1 Front control panel All of the commands and controls for the hob are found on the front panel MODEL 60 CONTROL PANEL DESCRIPTION OF THE KNOB The flame is lit by pressing the knob and simultaneously turning it anticlockwise to the minimum flame symbol To adjust the flame turn the knob to the zone between O maximum 6 and minimum Turn off the flame by turning the knob to position amp 6 a ARRANGEMENT OF THE BURNERS Desc
5. 1 0kPa To allow the unit to work back with this type of gas after it has been adjusted for LPG Propane perform the same operations described in paragraph 5 2 Adjustment for LPG Propane but refer to the following table for the proper injectors Burner NG 1 0 kPa Nominal gas Injector consumption MJ h mm Auxiliary 1 3 2 0 82 Semi rapid 2 4 8 1 00 Medium rapid 3 8 6 1 25 Large rapid 4 11 4 1 50 UR 5 2 13 5 E B 0 82 13 14 Instructions for the installer 6 FINAL OPERATIONS 6 1 Reassembling the hob Follow the instructions given in paragraph 5 1 Removing the hob but in the reverse order When replacing the burner rings remember that they have to be tightened completely by means of the wrench supplied otherwise the flame interruption zones on the flame crowns will not be aligned with the grid spokes When positioning the grids make sure that the pins are aligned with their seats in the surface then press them in with the palm of your hand until they lock in place 6 2 Adjustment of minimum for natural gas Replace the components on the burner and slide the knobs on the gas tap pins Light the burner and set it at minimum position Remove the knob and turn the regulation screw inside or next to the gas tap pin depending on the model until you get a suitable minimum flame Replace the knob and check flame stability by rapidly turning the knob from maximum to minimum The flame
6. Contents INSTRUCTIONS FOR SAFE AND PROPER USE POSITIONING OF THE HOB GAS CONNECTION ELECTRICAL CONNECTION ADAPTING TO DIFFERENT TYPES OF GAS FINAL OPERATIONS DESCRIPTION OF THE CONTROLS USING THE HOB CLEANING AND MAINTENANCE 10 PROBLEMS AND CAUSES AN DAA WH HS Thank you for choosing our product 10 11 12 14 16 17 18 19 es We advise you to read this manual carefully It contains all necessary instructions for maintaining unaltered the appearance and functional qualities of the hob functioning and carry out an inspection test INSTRUCTIONS FOR THE INSTALLER these are for the authorised persons who must carry out a suitable check of the gas system install the appliance set il INSTRUCTIONS FOR THE USER these contain user advice description of the commands and the correct procedures for cleaning and maintenance of the appliance gt e Se Introduction 1 INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE HOB WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE HOB ALSO KEEP THE SERIES OF NOZZLES SUPPLIED INSTALLATION MUST BE CARRIED OUT BY AUTHORISED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE THIS APPLIANCE IS INTENDED FOR DOMESTIC USES AND CONFORMS TO CURRENT REGULATIONS IN FORCE THE APPLIANCE HAS BEEN BUILT
7. DO NOT USE PANS OR GRIDDLE PLATES THAT EXTEND BEYOND THE EXTERNAL PERIMETER OF THE HOB THE APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR INFIRM PERSON WITHOUT SUPERVISION YOUNG CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY DO NOT PLAY WITH THE APPLIANCE REPLACED APPLIANCES MUST BE TAKEN TO A SPECIAL GARBAGE COLLECTION CENTRE WHERE THIS APPLIANCE IS INSTALLED IN MARINE CRAFT OR IN CARAVANS IT SHALL NOT BE USED AS A SPACE HEATER DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION The manufacturer declines all responsibility for damage to persons or things caused by non observance of the above prescriptions or by interference with any part of the appliance or by the use of non original spares Instructions for the installer 2 POSITIONING OF THE HOB It is the law that all gas appliances are installed by authorised persons Clearance around the appliance must comply with the requirements of AGA607 The following operation requires building and or carpentry work so must be carried out by a competent tradesman Installation can be carried out on various materials such as masonry metal solid wood or plastic laminated wood as long as they are heat resistant T 90 C 2 1 Attachment to the support structure Create an opening with the dimensions shown in the figure in the top surface of the counter keeping a minimum distance of 50 mm from the rear border This appliance is classifie
8. Flexible pipes if a flexible pipe is used it must be inspected periodically once a year for leakages if the surface of the pipe appears rigid and cracked disconnect immediately the cooker from the gas supply and replace the pipe with a new one Valves if the gas valves get stuck or hard to turn they need to be cleaned and re greased this operation must be carried out by an authorised person 10 PROBLEMS AND CAUSES Each of the following cases is caused by an abnormal operation of the appliance and should be dealt with by authorised persons please contact your local dealer or Service Center in case you detect any of these malfunctioning PROBLEM CAUSE WHAT TO D The flame is very long with Defect of comburent Clean the burner bright yellow tips Black air or incorrect Call Service Center if the deposits on the bottom of injectors problem remains the pans Burner dirty or flame ports obstructed The flame is very short and Excess of comburent Call Service Center noisy The flame moves air away from the burner ports The flame extinguishes Incorrect adjustment Call Service Center when the burner knob is set of the minimum heat to the low flame position input or excess of comburent air The valve knob is hard to Gas valve worn out or Call Service Center rotate needs lubrification 19 Spazio per targhetta caratteristiche Space for rating plate Espacio para placa caracteristica Espace puor plaquette signaletique Pla
9. Large rapid 5 UR SI Q Q min and max in cm 7 18 10 24 18 24 20 24 20 28 Cha Les 17 K y D Instructions for the user ome 9 CLEANING AND MAINTENANCE Before any intervention disconnect the power supply of the device 9 1 Cleaning stainless steel To keep the hob in good condition you should clean it after every use after it has cooled 9 1 1 Regular daily cleaning of the hob In order to clean and preserve the surface always use specific products only which do not contain abrasive substances or chlorine based acid substances How to use pour the product on a damp cloth and wipe the surface rinse thoroughly and dry with a soft cloth or deerskin 9 1 2 Food stains or residues Do not use metallic sponges or sharp scrapers they will damage the se surface Use normal non abrasive products and remove spots or residuals with non scratch sponges or if need be with wood or plastic utensils Rinse thoroughly and dry with a soft cloth or deerskin d 9 2 Cleaning of the components 9 2 1 Knob lt 3 The knobs are made of stainless steel and therefore should be cleaned in the same gt t ATES SS 18 way as the hob 9 2 2 Grids and burners cap In normal use of the hob the grids and burner caps normally get browned as a result tq Of the high temperature For optimum cleaning remove the burner cap and
10. aust fans shall be installed in accordance with the manufacturer s instructions However in no case shall the clearance between the highest part of the hob of the cooking appliance and a range hood be less than 600 mm or for an overhead exhaust fan 750 mm Any other downward facing combustible surface less than 600 mm above the highest part of the hob shall be protected for the full width and depth of the cooking surface area in accordance with Clause 5 12 1 2 However in no case shall this clearance to any surface be less than 450 mm Side clearances Measurements B amp C Where B measured from the periphery of the nearest burner to any vertical combustible surface is less than 200 mm the surface shall be protected in accordance with Clause 5 12 1 2 to a height C of not less than 150 mm above the hob for the full dimension width or depth of the cooking surface area Where the cooking appliance is fitted with a splashback protection of the rear wall is not required Additional requirements for Freestanding and Elevated Cooking Appliaces Measurements D amp E Where D the distance from the periphery of the nearest burner to a horizontal combustible surface is less than 200 mm then E shall be 10 mm or more or the horizontal surface shall be above the trivet Instructions for the installer See insets above NOTES 1 Requirement 3 does not apply to a freestanding or elevated cooking appliance which is des
11. d as type Y in relation to fire hazards and can therefore be mounted against walls higher than the work surface on condition that a certain distance X be kept between the appliance and the wall as shown in the figure so as to avoid damage from overheating Make sure there is a minimum of 600 mm between the hot plate flames and any shelf that may be installed directly above them In case of installation on a hollow compartment with doors a separating panel has to be placed under the hob Keep a minimum distance of 10 mm between the bottom of the unit and the panel surface The panel has to be easily removable to allow access in the event of technical service 38 mm leif X 220 mm dlelgbOofl X 280 mm 10 mm Instructions for the installer Carefully position the insulation gasket Supplied on the external perimeter of the hole made in the top surface see figures below and try to make it stick to the entire surface by applying light pressure with your hands Refer to the distances shown in the figure for the model to be installed keeping in mind that for both models the long front side has to skim the hole Secure the hob to the counter with brackets A Supplied Carefully trim any excess from border B of the gasket The distances in the following drawing refer to the hole on the inner side of the gasket 68 my psm
12. igned to prevent flames or the cooking vessels from extending beyond the periphery of the appliance 2 The cooking surface area is defined as that part of the appliance where cooking normally takes place and does not include those parts of the appliance containing control knobs For definition of hob see Clause 1 4 64 For definition of trivet see Clause 1 4 109 Consideration is to be given to window treatments when located near cooking appliances See Clause 5 3 4 LO BR 2 3 Room ventilation Caution This hob may only be installed and operated in rooms permanently ventilated in accordance with current regulations For proper operation of a gas appliance it is essential for the air necessary for combustion of the gas to be able to flow naturally into the room Air must flow directly into the room through openings in its outside walls This these opening s must have a free passage cross section of at least 100 cm or 200 cm for appliances not equipped with gas safety device These openings must be constructed so that they cannot be obstructed indoors or outdoors and should preferably be close to the floor on the side opposite to the combustion gas discharge point If it is not possible to make the openings in the room where the cooker is installed the necessary air may be taken from an adjoining room proveded it is not a bedroom or a room with fire risk 2 4 Discharge of combustion products Discharge of combustio
13. ly Before the appliance is operated make certain all relevant parts are placed in the correct position When the installation is completed the installation connections of appliance will require to be leak tested the burner operating pressure and flame checked and adjusted Warranty service calls do not cover these adjustments To check the operating pressure of the appliance it is recommended at least 2 large size burners are used Ensure appliance is secured to wall when installation is completed N G The regulator supplied must be fitted to the BSP thread at the rear of the appliance An approved manual shut off valve must be installed The N G regulator must be checked and adjusted to 1 0kPa after installation ULPG Can be connected to the inlet fitting directly The pressure must be checked to ensure it is operating at 2 5kPa A separate test point fitting must be installed between the piping amp the appliance for the pressure to be checked to ensure it is operating at 2 75kPa Instructions for the installer 4 ELECTRICAL CONNECTION Make sure that the voltage and capacity of the power line conform to the data shown Ee on the plate located under the casing Do not remove this plate for any reason The plug on the end of the supply cable and the wall socket must be the same type cS and conform to the current electrical system regulations Check that the power line is adequately grounded 7 On the power line in
14. n products must be guaranteed by means of hoods connected to a natural draught flue with certain efficiency or by means of forced aspiration An efficient aspiration system requires careful planning by a specialist capable of installing it respecting the positions and distances prescribed by standards After installation the installer must issue a certificate of conformity 10 Instructions for the installer 3 GAS CONNECTION This appliance is suitable for installation with Natural Gas or ULPG propane Refer to page 12 for the relevant burner pressure and appropriate injector sizes When the appliance is to be connected to Natural Gas then the pressure regulator supplied must be fitted to the gas inlet A test point for checking the gas pressure is supplied either with the regulator or aS a separate fitting in the case of ULPG propane appliances Connection of the appliance to the gas supply must be in accordance with the requirements of AS5601 A 1 2 BSP connector at the inlet is recommended and the gas supply line to the appliance must be of adequate length to allow sufficient withdrawal of appliance for service or disconnection and be 1 annealed copper pipe or 2 flexible hose according to AS NZ1869 amp be at least Class B 10 mm diameter The appliance must be installed with provision to allow the gas to be turned off and disconnected for servicing and removal of the appliance as required from the gas supp
15. oving the hob Remove all of the burner components by following the numerical sequence shown in the figure Remove all of the knobs 1 by pulling them upward Remove the grids 2 lifting up one of the two horizontal spokes Remove the burner caps 3 and flame crowns 4 With wrench A supplied open the bayonet clamps on the burner rings by levering on guides B Insert a wrench or a screw driver in one of the holes of the tool to simplify removal After having removed all of the above described components raise the surface to access the burners and gas taps Instructions for the installer 5 2 Adjustment for LPG Propane Check that the connection has been made as described in the Gas connection section Undo the screw C and push the air regulator D fully down Use a spanner to remove the nozzles E and fit those of suitable type following the instructions given in the tables for bottled gas LPG Propane 2 75 kPa The nozzle must not be tightened to a torque of over 3 Nm Burner LPG Propane 2 75 kPa Nominal gas Injector consumption MJ h mm Auxiliary 1 4 2 0 54 Semi rapid 2 5 9 0 65 Medium rapid 3 8 6 0 78 Large rapid 4 9 5 0 85 UR 5 13 5 E B 0 54 CAUTION for references A and B on the left UR and right UR burners see drawings at side 5 3 Adjustment for natural gas The hob has been adjusted for natural gas at a pressure of
16. ription of symbols REAR LEFT REAR RIGHT e FRONT LEFT O FRONT RIGHT j MIDDLE LEFT MIDDLE RIGHT MIDDLE Instructions for the user 8 USING THE HOB Check that the flame crowns the burner caps and grids are correctly assembled Pins A of the flame crowns must be inserted in housings B of the burner rings and pins C on the grids must be blocked in their respective housings on the hob 8 1 Ignition of the burners The device is fit with electronic ignition Simply press and simultaneously turn the knob counter clockwise on the low flame symbol until the burner is ignited The burner might go off when the knob is released In this case repeat the aforesaid operation keeping the knob pressed for more than 2 seconds Should the burners go off accidentally in the models with valves a safety device will trip after approximately 20 seconds to block the gas outlet even if the cock is open 8 2 Practical advice for using the burners For better burner performance and minimum gas consumption flat xX ZZ bottomed even pans must be used with covers and proportional in size to the burners see paragraph 8 3 Diameter of pans To avoid overcooking or damage to the surface top while cooking all pans or griddles must be positioned within the cooking hob perimeter and must be at a minimum distance of 3 4 cm from the knobs 8 3 Diameter of pans 1 Auxiliary 2 Semi rapid 3 Medium rapid 4
17. stall an omnipolar cut off device with contact cut off distance ay greater than or equal to 3 mm located in an easily accessible position near the unit Do not use reducers adapters or shunts than 1 0 mm 3 x 1 0 cable keeping in mind that the end to be connected to the hob must have the ground wire yellow green longer by at least 20 mm Use only HO5V2V2 F cable or similar which has a maximum temperature of 90 C Any replacement needed should be carried out by a specialised technician who should make the mains connections according to the following diagram nne N blue 20 mm of lf the power cable is replaced the wire section on the new cable must not be less yellow green by non observance of the above instructions or deriving from the tampering of even a A The manufacturer will not be liable for any damage to persons or property caused single part of the hob 11 12 j If j i i I j I f SS BE Instructions for the installer 5 ADAPTING TO DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work disconnect the appliance from the electrical socket The hob has been adjusted for natural gas at a pressure of 1 0 kPa For functioning with other types of gas the nozzles must be replaced and the primary air adjusted To replace the nozzles and regulate the burners you have to remove the top as described in the following paragraph 5 1 Rem
18. tz fur Typenschild Plaats voor typeplaatje Utrymme for Identifikationsplaten 914772108 E
Download Pdf Manuals
Related Search