Smeg KSEG56X Instruction Manual
Contents
1. e Insert the hood until the side supports snap into place e Lock in position by tightening the screws Vf from underneath the hood Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version connect the hood to the chimney using either a flexible or rigid pipe 120 mm 120 e Fix the pipe in position using sufficient pipe clamps not supplied e Remove any activated charcoal filters RECIRCULATION VERSION AIR OUTLET e Cut a hole 120 mm in the wall unit over the hood e Connect the hood body outlet to the top part of the wall unit using a rigid or flexible pipe 120 mm to be selected by the installer e Fix the pipe in position using sufficient pipe clamps not supplied Ensure that the activated charcoal filters have been inserted ELECTRICAL CONNECTION Connect the hood to the mains through a two pole switch having a contact gap of at least 3 mm When opening the sliding carriage for the first time after installing the hood pull it out briskly until it clicks USE Control Panel L Light Switches the lighting system on and off M Motor Switches the extractor motor on and off Vv Speed Sets the operating speed of the extractor MAINTENANCE Grease filters CLEANING METAL SELF SUPPORTING GREASE FILTERS The filters must be cleaned every two months of operation or more frequently with heavy usage e Remove the filters o2. governing electrical safety European Directive 89 336 CEE on Electromagnetic Compatibility and Directive 93 68 CEE regarding CE Marking Dieses Ger t entspricht folgenden EG Richtlinien Niederspannungsrichtlinie EWG 73 23 hinsichtlich elektrischer Sicherheit Richtlinie Elektromagnetische Vertr glichkeit EWG 89 336 und Richtlinie EWG 93 68 hinsichtlich der CE Kennzeichnung Cet appareil est conforme la norme europ enne en mati re de basse tension C E E 73 23 de s curit lectrique ainsi Ou aux normes europ ennes C E E 89 336 en mati re de compatibilit lectromagn tique et C E E 93 68 en mati re de label CE Dit apparaat voldoet aan de Europese laagspanningsnorm 73 23 EEG inzake de elektrische veiligheid en de Europese normen 89 336 EEG inzake de elektromagnetische compatibiliteit en 93 68 EEG inzake de CE markering Este aparato es conforme con la normativa europea sobre baja tensi n C E E 73 23 correspondiente a la seguridad el ctrica y a las normativas europeas C E E 89 336 sobre la compatibilidad electromagn tica e C E E 93 68 respeitante marca o CE 436001633 01 021210
3. ese Smeg Libretto Istruzioni Instruction Manual Bedienungsanleitung Manuel d Instructions Gebruiksaanwijzing Manual de Instru es KSEG56X KSEG 6X Dear Customer If you follow the recommendations contained in this Instruction Manual your appliance will give you constant high performance and will remain efficient for many years to come CONTENTS RECOMMENDATIONS AND SUGGESTIONS 10 CHARACTERISTICS 11 INSTALLATION 12 USE 14 MAINTENANCE 15 RECOMMENDATIONS AND SUGGESTIONS INSTALLATION The manufacturer will not be held liable for any damages resulting from incorrect or improper installation e The minimum safety distance between the cooker top and the extractor hood is 650 mm e Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood e For Class 1 appliances check that the domestic power supply guarantees adequate earthing Connect the extractor to the exhaust flue through a pipe of minimum diameter 120 mm The route of the flue must be as short as possible e Do not connect the extractor hood to exhaust ducts carrying combustion fumes boilers fireplaces etc e Ifthe extractor is used in conjunction with non electrical appliances e g gas burning appliances a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas The kitchen must have an opening communicating directly with the o
4. ne at a time after disconnecting the relative fastening elements e Wash the filters taking care not to bend them Allow them to dry before refitting e When refitting the filters make sure that the handle is visible on the outside Odour filters Recirculation version REPLACING ACTIVATED CHARCOAL FILTERS e These filters are not washable and cannot be regenerated and must be replaced approximately every four months of operation or more frequently with heavy usage e Dismantle the ducting support pulling the two pommels A simultaneously e Remove the saturated activated carbon filters by releasing the fixing hooks e Fit the new filters by hooking them into their seating e Close the ducting support by pushing and connecting the two pommels A Lighting LIGHT REPLACEMENT e 20 W halogen light e Dismantle the ducting support pulling the two pommels A simultaneously e Extract the Lamp from the Support e Replace with another of the same type making sure that the two pins are properly inserted in the lamp holder socket holes e Close the ducting support by pushing and connecting the two pommels A Quest apparecchio conforme alla norma europea sulla bassa tensione C E E 73 23 relativa alla sicurezza elettrica e alle norme europee C E E 89 336 relativa alla compatibilita elettromagnetica e C E E 93 68 relativa alla marcatura CE This appliance conforms to European Low Voltage Directive 73 23 CEE
5. pen air in order to guarantee the entry of clean air USE The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells e Never use the hood for purposes other than for which it has ben designed e Never leave high naked flames under the hood when it is in operation e Adjust the flame intensity to direct it onto the bottom of the pan only making sure that it does not engulf the sides e Deep fat fryers must be continuously monitored during use overheated oil can burst into flames e The hood should not be used by children or persons not instructed in its correct use MAINTENANCE e Switch off or unplug the appliance from the mains supply before carrying out any maintenance work e Clean and or replace the Filters after the specified time period e Clean the hood using a damp cloth and a neutral liquid detergent CHARACTERISTICS Dimensions Hood Type 52 70 L1 522 702 Components Ref Q ty Product Components 1 1 Hood Body complete with Controls Light Filters Q ty Documentation 1 Instruction Manual INSTALLATION Drilling the Support surface and Fitting the Hood Make a rectangular opening on the base of the hanging unit leaving a minimum of 13 mm from the outer edges Hood Type 52 70 L1 497 677 SNAP ON FITTING For hoods with snap on side supports only set up for a support panel thickness of between 15 mm and 30 mm
Download Pdf Manuals
Related Search