Smeg SE435XT Installation and Maintenance Manual
Contents
1. and a heaven sent intervention We suggest to fill the table below MARIK eisen ruhen MODEL reise seen ee SERIES seri rannte ee This appliance is marked according to the European directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE This guideline is the frame of a European wide validity of return and recycling on Waste Electrical and Electronic Equipment 11 122. plate with lukewarm soapy water Following this all parts should be thoroughly rinsed and dried Never wash them while they are still warm and never use abrasive powders Do not allow vinegar coffee milk salted water lemon or tomato juice from remaining in contact with the enamelled surfaces for long periods of time WARNINGS Correctly preserve the plate after use by treating it with special products easily available on the market This will keep the surface of the plate clean and bright The operation will also prevent the formation of rust Any liquid overflowed the pans must be always remove with a rag Don t use steam jets for the equipment cleaning INSTALLATION Installation and maintenance must only be carried out by a qualified installer Incorrect installation could cause damage to persons animals and property for which the manufacturer cannot be held responsible 4 INSTALLING THE HOT PLATE Check that the appliance is in a good condition after having removed the outer packaging and internal wrappings from around the various loose parts In case of doubt do not use the appliance and contact qualified personnel Never leave the packaging materials cardboard bags polystyrene foam nails etc within children s reach since they could become potential sources of danger The measurements of the opening made in the top of the modular cabinet and into which the hot plate will be installed are in
3. scheme with the characteristics of the components POWER OF ELECTRICAL COMPONENTS DENOMINATIONS W Normal plate 145 mm 1000 Normal plate 180 mm 1500 TYPE AND SECTION OF THE POWER CABLES Single phase power 110 V Cable type Three phase power 220 V 2N Three phase power 220 V 3N Rubber x HO5 RR F 3X 4 5 mm oa 5 X 2 5 mm 4X 2 5 mm olycroropene n HO5 RN F 3X 4 5 mm keeping in mind the contemporaneousness factor TECHNICAL DATA MODEL WITH 4 NORMAL PLATES VOLTAGE 110 V FREQUENCY 50 60 Hz TOT RATING 5000 W TECHNICAL ASSISTANCE AND SPARE PARTS This appliance before leaving the factory has been carefully tested and regulated by expert and specialized personnel in order to guarantee the best performances Any repairs or adjustments which may be subsequently required may only be carried out by qualified personnel with the utmost care and attention For this reason always contact your Dealer or your nearest After Sales Centre whenever repairs or adjustments are required specifying the type of fault and the model of appliance in your possession Please also note that genuine spare parts are only available from our After Sales Service Centres and authorized retail outlets The above data are printed on the data label put on the inferior part of the appliance and on the packing label The above informations give to the technical assistant the possibility to get fit spare parts
4. INSTRUCTIONS AND ADVICE FOR THE USE INSTALLATION AND MAINTENANCE OF BUILT IN ELECTRIC HOBS Dear Customer Thank you for having purchased one of our products We are certain that this new modern functional and practical appliance built with the very highest quality materials will meet your requirements in the best possible way This hob is easy to use lt is however important to thoroughly read the instructions in this handbook in order to obtain the best results The manufacturer shall not be held responsible for any damages to persons or property caused by incorrect installation or use of the appliance es smeg SMEG S p A Via Leonardo da Vinci 4 TIPO PAZ04 42016 GUASTALLA ITALIA MOD SE435XT The Manufacturer shall not be held responsible for any inaccuracies in this handbook due to printing or transcription errors the designs in the figures are purely indicative The Manufacturer also reserves the right to make any modifications to the products as may be considered necessary or useful also in the interests of the user without jeopardizing the main functional and safety features of the products themselves COD 01077SMSD 01077UK 27 06 2008 DESCRIPTION OF THE HOT PLATES TYPE PAZ 04 1 Normal plate Y 145 of 1000 W 2 Normal plate Y 180 of 1500 W 7 Control knob for electric plate n 1 8 Control knob for electric plate n 2 13 Warning light indicating that one or more plates are operating USE 1 S
5. WITCHING ON THE ELECTRIC PLATES The hobs may be equipped with three types of electric plates normal thermostat and rapid plates indicated by a red mark The normal plates and the rapid plates are controlled by a 7 position switch see fig 1 The thermostat plates are controlled by 12 position switch see fig 2 Switch on the plates by turning the knob to the required position A diagram is screen printed on the front panel This diagram indicates to which electric plate the knob in question corresponds see fig 1 2 A red warning light will come on to indicate that the plate has been ignited 2 HOW TO USE THE ELECTRIC PLATES A purely indicative plate regulation chart is given below TABLE NORMAL AND THERMOSTAT HEAT POSSIBLE COOKING RAPID PLATE PLATE INTENSITY PROCESSES Weak To dissolve butter chocolate etc To heat small amounts of liquid i To heat larger amounts of liquid To prepare cremes 2 1 4 Low me oe and suces requiring long slow cooking times To thaw frozen foods and prepare stews heatto boiling point or simmer 4 8 10 Medium To heat foods to boiling point To brown delicate meats and fish 10 12 nn re andsteaks Tosimmerlarge amounts e o o To bring large amounts of liquid to the boil For frying USE WARNINGS When the plate is switched on for the first time or if it has remained unused for a long period it should be dried for 30 minutes on switch position n 1 This will eli
6. dicated in either fig 4 comply with the measurements given for the hole into which the appliance will be recessed see fig 5 If a wood is installed above the hob please look at the hood manufacturer instructions regarding the minimum distance between hood and hob fig 5 5 FIXING THE HOT PLATE The hob has a special seal which prevents liquids from infiltrating into the cabinet Strictly comply with the following instructions in order to correctly apply this seal Detach the seals from their backing checking that the transparent protection still adheres to the seal itself Overturn the hob and correctly position seal E fig 6 under the edge of the hob itself so that the outer part of the seal itself perfectly matches the outer perimetral edge of the hob The ends of the strips must fit together without overlapping Evenly and securely fix the seal to the hob pressing it in place with the fingers Remove the strip of protective paper from the seal F it the hooks into their relative housings K in the unit and set the hob into the hole in the cabinet Lock it in place with the relative fixing screws F see fig 7 WARNINGS Be aware that the glue that join the laminated plastic to the furniture has to resist to temperature not below 150 C to avoid the unstuck of the panelling The installer should bear in mind that the mixed appliance is the Y type The rear wall adjacent and sur
7. minate any moisture that may have been absorbed by the insulating material To correctly use the appliance remember To place a pan on the plate before switching this on To always use pans with flat and very thick bottoms see fig 3 To never use pans that are smaller than the plate diameters To dry the bottom of the pan before placing it on the plate Correctly preserve the plate after use by treating it with special products easily available on the market This will keep the surface of the plate clean and bright The operation will also prevent the formation of rust Never allow children to play near the appliance when using the plates Check that the pan handles are positioned correctly The user should never leave the appliance unattended when cooking with easily inflammable oil and fat The plates will remain hot for a long period of time even after use Never touch them with the hands or other objects in order to prevent scorching If the appliance has a glass lid this could shatter when the cooker becomes hot Always disconnect all the plates before closing the lid Immediately disconnect the appliance from the electricity main as soon as cracks are noted on the surfaces of the plates FIG 3 CLEANING IMPORTANT Always disconnect the appliance from the electricity main before carrying out any cleaning operation 3 HOTPLATE If you want to preserve the surface clean and bright periodically wash the hot
8. ollowing instructions a Remove the hotplate from the top of the cabinet overturn it unscrew screw Z and remove under part see fig 9 b Shift connecting plate on terminal according to the following chart This chart is also affixed to the hob c Insert a supply cable of adequate section see chart par 10 through core hitch on the terminal board d Connect the phase and earth wires to the relative terminal board e Fix the supply cable in place using clamp f Refit the hotplate complying with the above instructions in reverse 110 V 50 60Hz y 110 Y 50 60Hz l o Y 50 60Hz y 110 Y 50 60Hz y 00 2 5 ra a D Pa o a a Q Q SERVICING Always disconnect the appliance from the electricity main before proceeding with any servicing operation 8 REPLACING THE ELECTRICAL COMPONENTS For access to the various parts remove the hotplate from the top of the cabinet Then overturn it unscrew screw Z and remove under part see fig 9 After these actions is possible to work on the plates commutators clamps and input cable N B In case of substitution of the input cable the installer must keep the earth conductor longer than live ones and must respect the cautions in paragraph Electrical connection To reassemble the appliance repeat the inverse process 9 TECHNICAL CHARACTERISTICS OF THE ELECTRICAL COMPONENTS To facilitate the job of the installer we present a
9. rounding surfaces must therefore be able to withstand an overtemperature of 65K INSTALLATION 6 ELECTRICAL CONNECTIONS Electrical connection must be carried out in compliance with the specifications and provisions in force Before proceeding with the connections check that The voltage rating of the appliance and the current sockets suits the maximum power draw of the appliance see data label affixed to the lower part of the appliance itself The system is equipped with an efficient earth connection in compliance with the pertinent provisions in force The manufacturer declines all responsibility for failure to comply with these provisions If the appliance has no power cable connect a cable of adeguate section to the terminal strip consult the table on next page complying with the wiring diagram of fig 8 This diagram is also affixed to the hot plate When connection to the electricity main is made by using a socket gas version only Fit a standard plug to power cable if supplyied This plug should be able to bear the load indicated on the data label Connect the wires according to the diagram in fig 8 remembering to comply with the following instructions Letter L live brown wire Letter N neutral blue wire Earth symbol yellow green wire The powering cable must be positioned so that it is never able to reach an overtemperature of 75 K in any part Never use reductions adapters or
10. shunts for the connection since these could cause false contacts and dangerous overheating The outlet must be accessible after the built in When the appliance is connected straight to the electricity main Install an omnipolar cutout between the appliance itself and the main This circuit breaker should be sized according to the rating of the appliance and the opening between its contacts should be at least 3 mm Remember that the earth wire must not be cutout by the switch Alternatively the electrical connection may also be protected by a high sensitivity differential switch Installers are strongly advised to connect the yellow green earthing wire to an efficient earthing system The manufacturer cannot be responsible for the missing earthing of the appliance WARNINGS All our appliances are designed and manufactured in compliance with European standards EN 60 335 1 EN 60 335 2 6 and EN 60 335 2 102 plus the relative amendments The appliance complies with the provisions of the following EEC Directives CEE 2004 108 CE regarding to electromagnetic compatibility CEE 2006 95 regarding electrical safety CONVERSIONS Disconnect the appliance from the mains supply prior to any conversions being carried out 7 CHANGING THE TYPE OF POWER SUPPLY Although they leave our factory preset for single phase connection certain appliances may by converted to the threephase system Comply with the f
Download Pdf Manuals
Related Search