Smeg ALFA141VE Instruction Manual
Contents
1. The display will show in order the temperature set the time remaining until the end of cooking and the program selected e It is possible to start the cooking early before the preheating temperature is reached by keeping the START button pressed for 3 seconds e During cooking it is possible to modify the temperature by turning the knob to the Ej or Fi symbols it will continue with the new setting after 3 seconds e During the last minute of cooking only the countdown of the remaining 60 seconds will be displayed At the end a beep and the text End flashing for 20 minutes will indicate that the cooking has been completed e At the end of the cooking operation to perform the same program again press the START button once more e To return to the OFF condition keep the STOP button pressed for 4 seconds The parameters set for the program are deleted se Instructions for the User 4 8 Preheating with delayed start The program with delayed pre heating is set as follows e Turn the knob to the Ej or F symbols to select the program P39 e Press the PUSH button for at least 3 seconds the display shows the current hour flashing e Turn the knob to the F or F symbols to set the current hour e Press the PUSH button the display will show the minutes flashing e Turn the knob to the or F symbols to set the minutes e Press the PUSH button the display will show th2. 415V3N the cable must be replaced by a HOZRN F am type The cross section of the wires of the new 380 415V 2N cable must not be less than 2 5 1 5 mm 4 x j 2 5 mm 2 5 mm 5 x 1 5 mm remembering that the end to be connected to the oven must have an _ el earth cable yellow green that is at least 20 20 mm mm longer 380 415V 3N 5 mmm 20 mm P Bs Instructions for the installer When linking up to mains by plug and socket the connection must be completed with a three core plug of adequate capacity 25A or for operation at 380 415V2N or 380 415V3N a five core plug 16A The plug and wall mounted socket must be of the same type in accordance with CEI regulations Make sure that the supply line is suitably earthed Avoid use of adapters and shunts If the appliance is connected to the electrical mains supply in a permanent manner install a multipolar cut out device on the line with contact opening distance equal to or greater than 3 mm located near the appliance and in an easily reachable position WARNING if the phase voltage drops below 190 VAC the performance of the oven may suffer not due to the product itself The terminal marked with this symbol connects parts together that are normally at zero potential Connect the appliances appropriately using this terminal in order to make sure that they are equipotential 2 1 1 Safety thermostat The oven is equipped with a safety de
3. below represents an example of cooking with 5 humidification cycles aed V z z z z 5 5 gt 14 14 14 N fi fi f fi fi V V V a Pe PE Prd eah Pe Cooking 10 minutes 0 5 5 10 5 10 5 cooking time f preset Start of End of preheating humidification cycle Start of cooking 29 30 Instructions for the User ome 4 5 Editing saving a program The oven has 38 programs that can be modified by the user from P01 to P38 To set the operational parameters of a program e Turn the knob to the Ej or F symbols to select the program you wish to save edit e Keep the PUSH knob pressed for 3 seconds the display will show the cooking temperature e Turn the knob to the Ej or F symbols to set the cooking temperature e Press the PUSH knob the display will show the cooking time e Turn the knob to the Ej or F symbols to set the cooking time from 1 to 99 min e Only on the steam model press the PUSH knob the display will show the H00 humidification cycle Turn the knob to the E or F symbols to set the humidification from H00 to H10 e Press the PUSH knob to exit from the data setting and saving phase The message PEnd will appear on the display and the parameters will be saved e After 3 seconds the display will show the parameters set in rotation e To return to the OFF condition keep the STOP button pr
4. ING TO THE EUROPEAN DIRECTIVE 2002 96 EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT WEEE THIS GUIDELINE IS THE FRAME OF A EUROPEAN WIDE VALIDITY OF RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT BEFORE THE APPLIANCE IS PUT INTO OPERATION ALL LABELS AND PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED The manufacturer declines all responsibility for damage to persons or things caused by the non observance of the above prescriptions or deriving from tampering with any part of the appliance or by the use of non original spares INFORMATION FOR USERS Pursuant to Directives 2002 95 EC 2002 96 EC and 2003 108 EC relating to the reduction of the use of hazardous substances in electrical and electronic appliances as well as to the disposal of refuse The crossed out bin symbol on the appliance indicates that the product at the end of its useful life must be collected separately from other refuse Therefore the user must consign the product that has reached the end of its working life to the appropriate selective collection centres for electrical and electronic refuse or deliver it back to the retailer when purchasing an equivalent product on a one for one basis Adequate selective collection for the subsequent forwarding of the decommissioned product to recycling treatment and ecologically compatible disposal contributes to avoiding possible negative effects on the environment and on health and promotes t
5. IOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST SELECTIVE WASTE COLLECTION CENTRE THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY REGULATIONS S WHEN LINKING UP TO MAINS BY PLUG AND SOCKET MAKE SURE THAT BOTH ARE COMPATIBLE AND CONNECT BY MEANS OF A POWER CABLE COMPLYING WITH APPLICABLE REGULATIONS NEVER UNPLUG BY PULLING ON THE CABLE oo DO NOT OBSTRUCT VENTILATION OR HEAT DISPERSAL OPENINGS IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST OF THE OVEN FOLLOWING THE INSTRUCTIONS BELOW SHOULD THE APPLIANCE NOT FUNCTION DISCONNECT IT FROM THE POWER SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE NEVER ATTEMPT TO REPAIR THE APPLIANCE NEVER PUT INFLAMMABLE OBJECTS IN THE OVEN IF IT SHOULD ACCIDENTALLY BE SWITCHED ON THIS MIGHT CAUSE A FIRE THE APPLIANCE BECOMES VERY HOT DURING USE SUITABLE HEAT PROOF GLOVES SHOULD BE WORN FOR ALL OPERATIONS THE ID PLATE WITH TECHNICAL DATA SERIAL NUMBER AND BRAND NAME IS POSITIONED VISIBLY ON THE SIDE OF THE OVEN DO NOT REMOVE THIS PLATE FOR ANY REASON 22 7 a b Instructions for safety and use THE APPLIANCE IS DESIGNED FOR PROFESSIONAL USE BY TRAINED PERSONS DO NOT ALLOW CHILDREN TO GO NEAR IT OR PLAY WITH IT TRAYS MUST BE WASHED BEFORE USE WITH A SUITABLE KITCHENWARE DETERGENT DO NOT USE ABRASIVE PRODUCTS THE OVEN IS DESIGNED FOR A MAXIMUM LOAD OF 3 5 KG THIS APPLIANCE IS MARKED ACCORD
6. ae ay Contents INSTRUCTIONS FOR SAFETY AND USE 0 8 22 OVEN INOTACLA TION Renner ee eer erry 24 DESCRIPTION OF CONTROLS ccceeeeeeeeeteeeeeeeeees 27 JING THE OVEN er suas 28 CLEANING AND MAINTENANCE cc cceeeeeeeeeeeeees 34 EXTRAORDINARY MAINTENANCE 0 cece tenes 36 x INSTRUCTIONS FOR THE USER these contain user advice description of the commands and the correct procedures for cleaning and maintenance of the appliance INSTRUCTIONS FOR THE INSTALLER these instructions are intended Pas for the qualified technician who must perform the installation put it into operation and test the appliance 21 Instructions for safety and use 1 INSTRUCTIONS FOR SAFETY AND USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE IT MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE OVEN WE URGE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE OVEN INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE THIS OVEN IS INTENDED FOR PROFESSIONAL USE AND CONFORMS TO THE EEC DIRECTIVES CURRENTLY IN FORCE THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS COOKING AND HEATING UP OF FOOD ALL OTHER USES ARE CONSIDERED IMPROPER THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER USE DO NOT DISCARD PACKING IN THE HOME ENVIRONMENT SEPARATE THE VAR
7. e runners with hot water and non abrasive detergent Rinse and dry 5 3 Door glazing The glass in the door should always be kept thoroughly clean Use absorbent kitchen roll in case of stubborn dirt remove with a damp sponge and an ordinary detergent 35 Instructions for the User ome 6 EXTRAORDINARY MAINTENANCE The oven may require extraordinary maintenance or replacement of parts subject to wear such as seals bulbs and so on The following instructions describe how to carry out these minor maintenance operations Before performing any operations switch off the power supply to seal the oven 6 1 Changing the light bulb Remove the bulb protector A Replace the bulb B with a similar one Re fit the bulb protector A MN Use only oven bulbs T 300 C ix 36 os Instructions for the User 6 2 Removing the door Open the door completely and insert the pins supplied into the holes from the inside Close the door to an angle of about 45 and lift it off To reassemble fit the hinges into their grooves then lower the door into place and extract the pins 6 3 Oven door seal To permit thorough cleaning of the oven the seal may be removed Before removing the seal take off the door as described above Once the door has been taken off lift the tabs at the corners as shown in the figure 37
8. e temperature flashing e Turn the knob to the or F symbols to set the temperature e Press the PUSH button the display will show the cooking start hour e Turn the knob to the Ej or fall symbols to set the cooking start hour e Press the PUSH button the display will show the minutes flashing e Turn the knob to the E or F symbols to set the minutes e Press the PUSH button to exit from the data setting and saving phase The text PEnd appears on the display and after 3 seconds it will display P39 the temperature and the pre heating start time in succession e To start the program press the START button for at least 2 seconds The display will show the current time and P39A in succession until the program is activated at the set time The oven will perform preheating at the set time during this phase the display shows P39 the text InF and the set temperature in succession this will continue until interrupted by the STOP button The program must be activated every day To reactivate it press the START button for at least 2 seconds 4 9 Rapid cooling The oven is equipped with a special function that allows the oven interior to be cooled rapidly To activate it when the display shows the text OFF open the door and press the START button for at leasts 4 seconds This will activate the internal motor fan the heating elements are switched off and the dis
9. essed for 4 seconds se Instructions for the User 4 6 Running a program From the OFF status proceed as follows Turn the knob to the Ee or F symbols to select one of the available programs from P01 to P38 The display will show the parameters of the selected program in rotation To start the program press the START button The appliance will perform a preheating cycle showing the message PrEh on the display When preheating is finished a series of beeps lasting 3 seconds indicate that is possible to proceed with the cooking operation The message PrEh will flash on the display To start the cooking keep the START pressed for 2 seconds The display will show in order the temperature set the time remaining until the end of cooking and the program selected It is possible to start the cooking early before the preheating temperature is reached by keeping the START button pressed for 3 seconds During the last minute of cooking only the countdown of the remaining 60 seconds will be displayed At the end a beep and the text End flashing for 20 minutes will indicate that the cooking has been completed To return to the OFF condition keep the STOP button pressed for 4 seconds During cooking if it is necessary to open the oven door the display shows the message door together with a continuous acoustic signal When the door is closed the oven will continue cooki
10. he recycling of the materials of which the appliance consists The illicit disposal of the product by the user results in the application of administrative sanctions 23 24 Instructions for the installer Pas 2 OVEN INSTALLATION The oven must be installed on a free standing horizontal work top The distance from the rear wall must allow easy access to the terminal board for connection of the power supply cable Installation must be carried out by a qualified technician and in compliance with EEC DIRECTIVES currently in force 2 1 Electrical connection Make sure the voltage and the cross section of the power cord match the specifications indicated on the identification plate positioned on the side of the oven Do not remove this plate for any reason The oven is equipped with a DIAGRAMMA COLLEGAMENTI three core HO7RN F cable for ORAMA OF LICAGODES i E operation at 220 240V ini roaraa ATE For operation at 380 415V2N or uN COLLEGAMENTO EFFETUATO IN FABBRICA 380 415V3N the power supply as CONEXION EFECTUADA EN LA FABRICA S K LIGACAO EFECTUADA NA FABRICA cable must be changed and the errs a A 400 415V 2N connection to the terminal board H must be modified This is can be LE accessed by removing the panel WEF located on the back of the oven The supplied cable is a HO7RN F 3 x 4 mm 220 240V 4 mm three core cable S For operating at 380 415V2N or 380
11. ng 31 32 Instructions for the User ome 4 6 1 Extending a cooking operation When a cooking operation finishes it is possible to extend it manually e While the display is showing the message End press the START button the text tP00 will appear on the display e Turn the knob to the or F symbols to set the additional minutes of cooking at most 20 extra minutes are allowed e To start the cooking extra time that has just been set press the START button for at least 2 seconds e Atthe end of cooking the text End will continue to flash for the next 20 minutes and the oven light will remain on 4 7 Manual cooking The manual program is P40 and can be edited by the user but does not save the cooking parameters set in memory To select this program proceed as follows e Save the program temporarily as described in chapter 4 5 Editing saving a program Unlike saved programs the cooking time can be set to infinite the display will show the text InP e After saving it DO NOT return to the OFF condition Press the START button The appliance will perform a pre heating cycle showing the text PrEh on the display e When preheating is finished a series of beeps lasting 3 seconds indicate that is possible to proceed with the cooking operation The text PrEh will flash on the display e To start the cooking keep the START button pressed for 2 seconds
12. on is single phase Turn the knob to the Ed or F symbols to move between the proposed power absorptions P8 3 P5 5 and P3 0 if the oven connection is three phase or P5 5 and p3 0 if the oven connection is single phase Once you have selected the power press the PUSH button to confirm the selection The power setting operation must be performed the first time that the oven is connected The value set is stored and used automatically whenever the oven is used subsequently ox Instructions for the User 4 3 Choice of programs This appliance allows you select 40 cooking programs including e 38 programs that can be edited and saved as the user wishes e 1 manual program P40 e 1 preheating program with delayed start P39 4 4 Humidified cooking operations only in the steam model The humidified programs that the user can modify are included between P01 and P40 apart from program P39 For each program it is possible to increase the number of the humidification cycles from 0 to 10 where O corresponds to traditional cooking without using humidification Humidification cycles can be modified only if an oven temperature higher than 150 C is set Water can be allowed to flow inside the cooking chamber only during cooking by controlling the relevant inlet valve manually To do this just keep the START button pressed for at least one second Releasing the button stops the water from flowing in The diagram
13. play shows the text To stop the function press the STOP button 33 34 A 3 ex Instructions for the User ome 5 CLEANING AND MAINTENANCE Important do not aim jets of water directly against the oven avoid the use of pressure jets Before performing any operations switch off the power supply to the oven 5 1 Cleaning stainless steel To keep stainless steel in good condition it should be cleaned regularly at the end of the day Let it cool first To clean and preserve the stainless steel surfaces always use only specific products that do not contain abrasives or chlorine based acids How to use pour the product onto a damp cloth and wipe the surface rinse thoroughly and dry with a soft cloth or deerskin Do not use metallic sponges or sharp scrapers they will damage the surface Use ordinary non abrasive products for steel with the aid of wooden or plastic utensils if necessary a Rinse thoroughly and dry with a soft cloth or deerskin FF os y A Instructions for the User 5 2 Cleaning the oven interior To keep the oven in good condition it should be cleaned regularly at the end of the day Let it cool first Take out all removable parts Remove the side runners by extracting the hook C from the hole or from the pin D depending on the model and the pin A from the hole B on the bottom of the oven oS oS e Clean the oven racks and sid
14. ton lets you start cooking operations or perform a rapid cooling cycle when they are finished In the steam model it starts the humidification cycle STOP BUTTON This button lets you stop cooking at any time DISPLAY This lets you display the selected program and related cooking parameters as well as the operating power PROGRAM SELECTION KNOB Allows you to set the cooking operation using one of the preset programs to select the temperature and duration of the cooking operation as well as the operating power 28 Instructions for the User ome 4 USING THE OVEN 4 1 Warnings and general advice When using the oven for the first time heat it up to its maximum temperature for a duration long enough to burn off any oily residues from the manufacturing process To access food always leave the door open as short a time as possible to prevent the temperature in the oven from falling and ruining the food 4 2 Setting the power When connecting the oven for the first time the maximum power absorbed will appear flashing on the display If the product is already connected this will be in the OFF state In both cases proceed as follows Press the PUSH knob for at least 3 seconds the display will show the text P8 3 equivalent to the maximum absorbed power of 8 3 kW if the oven connection is three phase or P5 5 equivalent to the maximum absorbed power of 5 5 kW if the oven connecti
15. vice that takes action in case of serious malfunction To re arm the safety device you must contact the technical assistance service The manufacturer declines all responsibility for damage to persons or things caused by the non observance of the above prescriptions or deriving from tampering with any part of the appliance 2 2 Levelling Level the oven on the ground using the four adjustable feet In order to adjust them loosen the lock nut and unscrew the foot The adjustment screws have a range of 10 mm 25 26 Instructions for the installer Pas 2 3 Connection to the water mains only in the steam model Connect the water inlet socket on the back to a water socket with a threaded 34 gas opening taking care to screw it tightly to the hose If the water piping is new or has been unused for a long time before connection run the water to make sure it becomes clear and free of impurities Without this precaution there is a risk that the water inlet will become clogged causing damage to the appliance It is recommended to supply the oven with water pressure between min 50 kPa and max 500 kPa 2 4 Steam outlet pipe Depending on the model there are two outlet pipes on the back of the oven for releasing the steam produced during cooking These must be left free of any obstruction Avoid crushing them ef os Instructions for the User 3 DESCRIPTION OF CONTROLS START BUTTON This but
Download Pdf Manuals
Related Search