SMC Networks Switch SMCGS24 User's Manual
Contents
1. 17 PRODUCT SPECIFICATIONS PRODUCT SPECIFICATIONS EZ Switch 10 100 1000 12 Standards Conformance TEEE 802 3 2002 Ethernet Fast Ethernet Gigabit Ethernet Full duplex flow control Communication Rate 10 100 and 1000 Mbps Communication Mode Full or half duplex at 10 100 Mbps Full duplex at 1000 Mbps Media Supported 10BASE T 100 ohm Category 3 or better twisted pair 100BASE TX 100 ohm Category 5 or better twisted pair 1000 5 100 ohm Categoty 5 5e 6 twisted pair Number of Ports SMCGS16 16 RJ 45 1000BASE T ports SMCGS24 24 RJ 45 1000BASE T ports Indicator Panel Power Ports Link Act 100 1000M Dimensions 33 x 20 4 x 4 4 cm 12 99 x 8 04 x 1 73 in EZ Amen 10 100 1000 Weight SMCGS16 2 0 kg 4 04 lbs SMCGS24 2 2 kg 4 85 lbs MAC Addtess Table 8 K entries Memory Buffer SMCGS16 272 Kbits on chip frame buffer SMCGS24 400 Kbits on chip frame buffer Power Consumption SMCGS16 15 8 Watts SMCGS24 24 2 Watts Heat Dissipation 130 BTU hr maximum Power Requirement Input Voltage 100 240 VAC 50 60 Hz Temperature Operating 0 40 C 32 104 F Storage 40 70 C 40 158 F Humidity 5 to 95 non condensing EMC Safety Compliances CE Mark Immunity EN 61000 4 2 3 4 5 6 8 11 Emissions FCC Class A CISPR Class A EN 61000 3 2 3 Safety CSA CUS CSA60950 1 amp UL60950 1 TUV GS EN60950 1 IEC60950 1 13 PRODUCT SPECIFICATIONS2. SMC will provide warranty service for one year following discontinuance from the active SMC price list Under the limited lifetime warranty internal and external power supplies fans and cables are covered by a standard one year warranty from date of purchase SMC Networks Inc 38 Tesla Irvine CA 92618 COMPLIANCES COMPLIANCES FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help EC Conformance Declaration Class A SMC contact fo
3. 14
4. connection Off The port has not established a network connection Flashing Traffic is passing through the port 100 On Green Indicates the port is operating at 1000 Mbps 1000 On Yellow Indicates the port is operating at 100 Mbps Off Indicates the port is operating at 10 Mbps SMCGS16 REAR PANEL EZ Switch 10 100 1000 M 4 d e ee 2 Link Act 00000000 2922225 SMCGS16 MS wes So Gy a Sa Se Se ww 0 009000000 Loha AG rag OL dE AL AG D 9 B s s 100 240V 50 608 EZ Switch 10 100 1000 4 a a x 5 D 7 n r e Y er lar Ar e LinkiAct 299999999 S09 SMCGS24 1000 100m 000000000000 QAR ARR SAAB term QE ES SES we M A Rear Panel The AC power connector is located on the rear panel of the switch INSTALLING THE SWITCH INSTALLING THE SWITCH Before installing the switch verify that you have all the items listed under Package Contents Note that the switch can be installed on any suitably large flat surface or in a standard 19 inch rack Package Contents The EZ Switch 10 100 1000 includes EZ
5. die eine Wartung vom Benutzer ben tigen Installation und Deinstallation des Ger tes m ssen von qualifiziertem Servicepersonal durchgef hrt werden Wenn das Ger t an eine Steckdose angeschlossen wird mu der Masscanschlu am dreipoligen Netzstecker mit Schutzerde verbunden werden um elektrische Gefahren zu vermeiden COMPLLANCES Environmental Statement The manufacturer of this product endeavours to sustain an environmentally friendly policy throughout the entire production process This is achieved though the following means Adherence to national legislation and regulations on environmental production standards Conservation of operational resources Waste reduction and safe disposal of all harmful un recyclable by products Recycling of all reusable waste content Design of products to maximize recyclables at the end of the product s life span Continual monitoring of safety standards End of Product Life Span This product is manufactured in such a way as to allow for the recovery and disposal of all included electrical components once the product has reached the end of its life Manufacturing Materials There are no hazardous nor ozone depleting materials in this product Documentation All printed documentation for this product uses biodegradable paper that originates from sustained and managed forests The inks used in the printing process are non toxic Purpose This guide details the
6. 328 ft RJ 45 100BASE TX 2 pair Cat 5 or better 100 ohm 100 m 328 ft RJ 45 1000BASE T 4 pair Cat 5 or better 100 ohm UTP 100 m 328 ft RJ 45 10BASE T 100BASE TX Pin Assignments Caution DO NOT plug a phone jack connector into any RJ 45 port Use only twisted pair cables with RJ 45 connectors that conform with FCC standards 4 Use unshielded twisted pair UTP or shielded twisted pair STP cable for RJ 45 connections 100 ohm Category 3 or better cable for 10 Mbps connections or 100 ohm Category 5 or better cable for 100 Mbps connections Also be sure that the length of any twisted pair connection does not exceed 100 meters 328 feet Because all ports on this switch support automatic MDI MDI X operation you can use straight through cables for all network connections to PCs or servers or to other switches or hubs In straight through cable pins 1 2 3 and 6 at one end of the cable are connected straight through to pins 1 2 3 and 6 at the other end of the cable CABLES The table below shows the 10BASE T 100BASE TX MDI X and MDI port pinouts Pin MDI X Signal Name MDI Signal Name 1 Receive Data plus RD Transmit Data plus TD 2 Receive Data minus RD Transmit Data minus TD Transmit Data plus TD Receive Data plus RD 6 Transmit Data minus TD Receive Data minus RD 4 5 7 8 Not used at 10 100 Mbps Not used at 10 100 Mbps 10
7. Switch 10 100 1000 SMCGS16 or SMCGS24 Four rubber foot pads Rack mount bracket kit Appropriate AC power cord This User Guide SMC Warranty Registration Card Selecting a Site Be sure to follow the site selection guidelines below when choosing a location e Select a suitable location for the switch It should be accessible for installing cabling and maintaining the switch The temperature and humidity should be within the ranges listed in the specifications The status LEDs should be clearly visible INSTRUCTIONS There should be adequate space approximately two inches on all sides for proper air flow Make sure twisted pair cable is always routed away from power lines fluorescent lighting fixtures and other sources of electrical interference such as radios transmitters etc Make sure that a properly grounded power outlet is within 2 44 meters 8 feet of the switch and 1s powered from an independent circuit breaker As with any equipment using a filter or surge suppressor is recommended Instructions 1 Positioning the Switch For desktop or shelf mounting attach the four adhesive foot pads to the bottom of the switch For rack mounting install into a standard 19 inch rack using the included brackets 2 Applying Power Plug one end of the power adapter into the socket on the switch s rear panel and the other end into an appropriate electrical outlet Check the Power
8. facile Vous ne pouvez mettre l appareil hors circuit qu en d branchant son cordon lectrique au niveau de cette prise L appareil fonctionne une tension extr mement basse de s curit qui est conforme la norme IEC 60950 Ces conditions ne sont maintenues que si l quipement auquel il est raccord fonctionne dans les m mes conditions France et P rou uniquement Ce groupe ne peut pas tre aliment par un dispositif imp dance la terre Si vos alimenta tions sont du type imp dance la terre ce groupe doit tre aliment par une tension de 230 V 2 P T par le biais d un transformateur d isolement rapport 1 1 avec un point secondaire de connexion portant l appellation Neutre et avec raccordement direct la terre masse Cordon lectrique Il doit tre agr dans le pays d utilisation Etats Unis et Can Le cordon doit avoir re u l homologation des UL et un certificat de ada la CSA Les spe cifications minimales pour la corde flexible sont AWG No 18 ou AWG No 16 pour une longueur infe rieure a 2 me tres type SV ou SJ 3 conducteurs Le cordon doit tre en mesure d acheminer un courant nominal d au moins 10 A La prise femelle de branchement doit tre du type mise la terre mise la masse et respecter la configuration NEMA 5 15P 15 A 125 V ou NEMA 6 15P 15 A 250 V Danemark La prise m le d alimentation doit respecter la section 107 2 D1 de la norm
9. for the SMCGS16 is illustrated below EZ Switch 10 100 1000 SMCGS16 D o a Internet d SS SH 1 De SMC EZ109DT N p 54 Notebook SMC2804WBR Wireless 1 N Broadband Router UA Workstations With 5 9452 Gigabit Workstations PCI Cards gt Notebook with SMC2835W Wireless PC Card TROUBLESHOOTING TROUBLESHOOTING Diagnosing Switch Indicators 1 Symptom Power LED does not light after power on Probable Causes AC power cord may be defective Possible Solutions Check for loose connections Check the power outlet by using it for another device Replace the AC power 2 Symptom Link LED does not light after connection is made Probable Causes Switch port network card or cable may be defective Possible Solutions Check that the switch and attached device are both powered on Be sure the network cable is connected to both devices Verify that Category 5 or better cable is used for 10 100 Mbps connections Category 5 or 5e cable for 1000 Mbps connections and that the length of any cable does not exceed 100 meters 328 feet Check the network and cable connections for defects Replace the defective card or cable if necessary Cable Specifications CABLE SPECIFICATIONS CABLES Cable Types and Specifications Cable Type Max Length Connector 10BASE T 2 pair Cat 3 or better 100 ohm UTP 100 m
10. hardware features of the switch including Its physical and performance related characteristics and how to install the switch Audience The guide is intended for use by network administrators who are responsible for installing and setting up network equipment consequently it assumes a basic working knowledge of LANs Local Area Networks Diese Anleitung ist f r die Benutzung durch Netzwerkadministratoren vorgeschen die f r die Installation und das einstellen von Netzwerkkomponenten verantwortlich sind sie setzt Erfahrung bei der Arbeit mit LANs Local Area Networks voraus COMPLIANCES Safety Compliance Warning Fiber Optic Port Safety When using a fiber optic port never look at the transmit laser while CLASS it is powered on Also never look directly at the fiber TX port and LASER DEVICE fiber cable ends when they are powered on Avertissment Ports pour fibres optiques s curit sur le plan optique Ne regardez jamais le laser tant qu il est sous tension Ne regardez DISPOSITIF LASER jamais directement le port TX Transmission fibres optiques et les DE CLASSE embouts de cables a fibres optiques tant qu ils sont sous tension Warnhinweis Faseroptikanschliisse Optische Sicherheit Niemals ein Ubertragungslaser betrachten wahrend dieses LASERGERAT eingeschaltet ist Niemals direkt auf den Faser TX Anschlu und auf DER KLASSE die Faserkabelenden schauen w hrend diese eingeschaltet sind xi COMPL
11. 00BASE T Pin Assignments The table below shows the 1000BASE T MDI and MDI X port pinouts These ports require that all four pairs of wires be connected Note that for 10 1000BASE T operation all four pairs of wires are used for both transmit and receive Use 100 ohm Category 5 or 5e unshielded twisted pair UTP or shielded twisted pair STP cable for 1000 5 connections Also be sure that the length of any twisted pair connection does not exceed 100 meters 328 feet Pin MDI X MDI 1 Bi directional Data Two Plus BI_D2 Bi directional Data One Plus BI_D1 2 Bi directional Data Two Minus BI_D2 Bi directional Data One Minus BI_D1 3 Bi directional Data One Plus BI_D1 Bi directional Data Two Plus BI_D2 4 Bi directional Data Four Plus 04 Bi directional Data Three Plus BI_D3 5 Bi directional Data Four Minus BI_D4 Bi directional Data Three Minus BI_D3 6 Bi directional Data One Minus BI_D1 Bi directional Data Two Minus BI_D2 7 Bi directional Data Three Plus BI_D3 Bi directional Data Four Plus BI_D4 8 Bi directional Data Three Minus BI_D3 Bi directional Data Four Minus BI_D4 1000BASE T CABLE REQUIREMENTS 1000BASE T Cable Requirements All Category 5 UTP cables that are used for 100BASE TX connections should also work for 1000BASE T providing that all four wire pairs are connected However it is recommended that for
12. LANCES xii TABLE CONTENTS ana DIS NES QR REE area 1 Features and Benefits nn 1 Front Panel R 45 Ports Pee eser enis 2 Front Panel LEDS 1 ERE IE NV DP Rte RES 2 s ee ne HE Wer RE IEEE 3 Rear Panel e A PUE RC QS Installing the Switch 4 Package Contents SoS oe RE 4 Selecttp a Site een eech 4 5 Application 1 7 Troubleshooting see tw Y Y es 8 Diagnosing Switch Indicators 8 Cables xu 52 bee es E we ote Bee hens 9 Cable Specifications ser ese Ie ED Emma rn 9 10BASE T 100BASE TX Pin Assignments 9 1000BASE T Pin Assignments 10 1000BASE T Cable Requirements 11 Cable Testing for Existing Category 5 Cable 11 Adjusting Existing Category 5 Cabling 11 Product 5 12 EZ Switch 10710071000 cronos cease Pa 12 vii viii FEATURES AND BENEFITS INTRODUCTION The EZ Switch 10 100 1000 SMCGS16 and SMCGS24 ate high performance Gigabit Ethernet switches designed for delivering Gigabit connectivity to the desktop They provide 16 24 full duplex 1000BASE T ports that significantly improve network pe
13. LED to be sure power is on Note Itis not necessaty to powet off the switch before connecting or disconnecting any UTP cables as these actions will not disrupt the operation of other devices attached to the switch 3 Connecting PCs Connect each PC to an RJ 45 port on the switch using Categoty 5 or 5e shielded or unshielded twisted pair UTP or STP cable maximum length 100 meters 328 ft The EZ Switch 10 100 1000 will support up to 16 PCs All ports on the switch support automatic MDI MDI X operation so you can use straight through cables for all network connections to PCs servers or to other switches or hubs INSTALLING THE SWITCH Note attached device does not support auto negotiation the data rate will be sensed automatically and the communication mode will default to half duplex 4 Cascading Switches and Other Network Devices All the ports on the switch support automatic MDI MDI X configuration for cable connections This allows you to use straight through cable to connect to other switches or hubs from any port on the switch No crossover cables or other device settings are needed See the Cable Specifications on page 9 of this guide for further information Caution Do not plug a phone jack connector into any RJ 45 port This may damage the switch Instead use only twisted pair cables with RJ 45 connectors that conform with FCC standards INSTRUCTIONS APPLICATION EXAMPLE A typical application
14. OCT OMCGS Al 16 24 Port 1007 000 Mbps 10 Switch EZ Switch 10 100 1000 User Guide From SMC s EZ line of low cost workgroup LAN solutions SMC Networks 38 Tesla April 2005 Irvine CA 92618 Phone 949 679 8000 Pub 150000017200H R01 Information furnished by SMC Networks Inc SMC is believed to be accurate and reliable However no responsibility is assumed by SMC for its use nor for any infringements of patents or other rights of third parties which may result from its use No license is granted by implication or otherwise under any patent or patent rights of SMC SMC reserves the right to change specifications at any time without notice SMC Networks Inc 38 Tesla Irvine CA 92618 All rights reserved Trademarks SMC is a registered trademark and EZ Switch is a trademark of SMC Networks Inc Other product and company names are trademarks or registered trademarks of their respective holders LIMITED WARRANTY Limited Warranty Statement SMC Networks Inc SMC warrants its products to be free from defects in workmanship and materials under normal use and service for the applicable warranty term All SMC products carry a standard 90 day limited warranty from the date of purchase from SMC or its Authorized Reseller SMC may at its own discretion repair or replace any product not operating as warranted with a similar or functionally equivalent product during th
15. TIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE OR USE OF ITS PRODUCTS SMC SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER S OR ANY THIRD PERSON S MISUSE NEGLECT IMPROPER INSTALLATION OR TESTING UNAUTHORIZED ATTEMPTS TO REPAIR OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE OR BY ACCIDENT FIRE LIGHTNING OR OTHER HAZARD LIMITATION OF LIABILITY IN NO EVENT WHETHER BASED IN CONTRACT OR TORT INCLUDING NEGLIGENCE SHALL SMC BE LIABLE FOR INCIDENTAL CONSEQUENTIAL INDIRECT SPECIAL OR PUNITIVE DAMAGES OF ANY KIND OR FOR LOSS OF REVENUE LOSS OF BUSINESS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE USE PERFORMANCE FAILURE OR INTERRUPTION OF ITS PRODUCTS EVEN IF SMC OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS WHICH MAY VARY FROM STATE TO STATE NOTHING IN THIS WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS
16. all critical connections or any new cable installations 4 pair Category 5e enhanced Category 5 cable should be used The Category 5e specifications include test parameters that are only recommendations for Category 5 Therefore the first step in preparing existing Category 5 cabling for running 1000BASE T is a simple test of the cable installation to be sure that it complies with the IEEE 802 3ab standards Cable Testing for Existing Category 5 Cable Installed Category 5 cabling must pass tests for Attenuation Near End Crosstalk NEXT and Far End Crosstalk FEXT This cable testing information is specified in the ANSI TIA EIA TSB 67 standard Additionally cables must also pass test parameters for Return Loss and Equal Level Far End Crosstalk ELFEXT These tests are specified in the ANSI TIA EIA TSB 95 Bulletin The Additional Transmission Performance Guidelines for 100 Ohm 4 Pair Category 5 Cabling Note that when testing your cable installation be sure to include all patch cables between switches and end devices Adjusting Existing Category 5 Cabling If your existing Category 5 installation does not meet one of the test parameters for 1000 5 there are basically three measures that can be applied to try to correct the problem 1 Replace any Category 5 patch cables with high performance Category 5e ot 6 cables 2 Reduce the number of connectors used in the link 3 Reconnect some of the connectors in the link
17. d by radio frequency fields EN 61000 4 6 1996 0 15 80 MHz with 1 kHz AM 80 Modulation 3 V m Power frequency magnetic field immunity test according to EN 61000 4 8 1993 1 A m at frequency 50 Hz Voltage dips short interruptions and voltage variations immunity test according to EN 61000 4 11 1994 gt 95 Reduction 10 ms 30 Reduction 9500 ms gt 95 Reduction 225000 ms LVD EN 60950 1 2001 Industry Canada Class A This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference causing equipment standard entitled Digital Apparatus ICES 003 of the Department of Communications Cet appareil num rique respecte les limites de bruits radio lectriques applicables aux appareils num riques de Classe prescrites dans la norme sur le mat riel brouilleur Appareils Num riques NMB 003 dict e par le minist re des Communications Japan VCCI Class A CORES MUESTRE SHARES VCCI ORM lt 3 A IT CORELRER CHATS LER COMA MEN DURAS SESBRENSCEMBVEF COMPLIANCES Please read the following safety information carefully before installing the Switch WARNING Installation and removal of the unit must be carried out by qualified personnel only This guide is intended for use by network administrators who are responsible for setting up and installing network equipment consequently it assumes a ba
18. e DK2 1a ou DK2 5a vii COMPLLANCES viii Cordon lectrique Il doit tre agr dans le pays d utilisation Suisse La prise male d alimentation doit respecter la norme SEV ASE 1011 Europe La prise secteur doit tre conforme aux normes CEE 7 7 SCHU KO LE cordon secteur doit porter la mention lt HAR gt ou lt BASEC gt et doit tre de type HO3VVF3GO 75 minimum Bitte unbedingt vor dem Einbauen des RPU die folgenden Sicherheitsanweisungen durchlesen WARNUNG Die Installation und der Ausbau des Ger ts darf nur durch Fachpersonal erfolgen Diese Anleitung ist fr die Benutzung durch Netzwerkadministratoren vorgesehen die fr die Installation und das einstellen von Netzwerkkomponenten verantwottlich sind sie setzt Erfahrung bei der Arbeit mit LANs Local Area Networks voraus Das Ger t sollte nicht an eine ungeerdete Wechselstromsteckdose angeschlossen werden Das Ger t mu an eine geerdete Steckdose angeschlossen werden welche die internationalen Sicherheitsnormen erf llt Der Ger testecker der Anschlu an das Ger t nicht der Wandsteckdosenstecker mu einen gem EN 60320 IEC 320 konfigurierten Gerateeingang haben Die Netzsteckdose mu in der N he des Ger ts und leicht zug nglich sein Die Stromversorgung des Ger ts kann nur durch Herausziehen des Geratenetzkabels aus der Netzsteckdose unterbrochen werden Der Betrieb dieses Ger ts erfo
19. e applicable warranty term SMC will endeavor to repair or replace any product returned under warranty within 30 days of receipt of the product The standard limited warranty can be upgraded to a Limited Lifetime warranty by registering new products within 30 days of purchase from SMC or its Authorized Reseller Registration can be accomplished via the enclosed product registration card or online via the SMC Web site Failure to register will not affect the standard limited warranty The Limited Lifetime warranty covers a product during the Life of that Product which is defined as the period of time during which the product is an Active SMC product A product is considered to be Active while it is listed on the current SMC price list As new technologies emerge older 94 technologies become obsolete and SMC will at its discretion replace older product in its 8 product line with one that incorporates these newer technologies At that point the obsolete roduct is discontinued and is no longer an Active SMC product A list of discontinued P 8 P products with their respective dates of discontinuance can be found at http www smc com index cfm action customer service warranty All products that are replaced become the property of SMC Replacement products may be either new or reconditioned Any replaced or repaired product carties either a 30 day limited warranty or the remainder of the initial warranty which
20. ever is longer SMC is not responsible for any custom software or firmware configuration information or memory data of Customer contained in stored on or integrated with any products returned to SMC pursuant to any warranty Products returned to SMC should have any customer installed accessory or add on components such as expansion modules removed prior to returning the product for replacement SMC is not responsible for these items if they are returned with the product Customers must contact SMC for a Return Material Authorization number prior to returning any product to SMC Proof of purchase may be required Any product returned to SMC without a valid Return Material Authorization RMA number clearly marked on the outside of the package will be returned to customer at customer s expense For warranty claims within North America please call our toll free customer support number at 800 762 4968 Customers are responsible for all shipping charges from their facility to SMC SMC is responsible for return shipping charges from SMC to customer LIMITED WARRANTY WARRANTIES EXCLUSIVE IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE CUSTOMER S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN QUESTION AT SMC S OPTION THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS EXPRESS OR IMPLIED EITHER IN FACT OR BY OPERATION OF LAW STATUTORY OR OTHERWISE INCLUDING WARRAN
21. lgt unter den SELV Bedingungen Sicherheitskleinstspannung gem IEC 60950 Diese Bedingungen sind nur gegeben wenn auch die das Ger t angeschlossenen Ger te unter SELV Bedingungen betrieben werden COMPLIANCES Stromkabel Dies muss von dem Land in dem es benutzt wird gepriift werden Schweiz Dieser Stromstecker mu die SEV ASE 1011Bestimmungen ein halten Europe Das Netzkabel mu vom Typ HO3VVF3GO 75 Mindestan forderung sein und die Aufschrift lt HAR gt oder lt BASEC gt tragen Der Netzstecker mu die Norm CEE 7 7 erf llen SCHUKO Warnings and Cautionary Messages Warning Warning Warning Caution Caution Caution This product does not contain any serviceable user parts Installation and removal of the unit must be carried out by qualified personnel only When connecting this device to a power outlet connect the field ground lead on the tri pole power plug to a valid earth ground line to prevent electrical hazatds Wear an anti static wtist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment Do not plug a phone jack connector in the RJ 45 port This may damage this device Les raccordeurs ne sont pas utilis pour le syst me t l phonique Use only twisted pair cables with RJ 45 connectors that conform to FCC standards Warnings in German Achtung Achtung Achtung Dieses Produkt enthalt keine Teile
22. r these products in Europe is SMC Networks Europe Edificio Conata Il Calle Fructu s Gelabert 6 8 22 42 08970 Sant Joan Desp Barcelona Spain This information technology equipment complies with the requirements of the Council Directive 89 336 EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73 23 EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93 68 EEC For the evaluation of the compliance with these Directives the following standards were applied RFI Emission Limit class A according to EN 55022 1998 60601 1 2 medical Limit class A for harmonic current emission according to EN 61000 3 2 1995 Limitation of voltage fluctuation and flicker in low voltage supply system according to EN 61000 3 3 1995 Immunity Product family standard according to EN 55024 1998 111 COMPLIANCES lv Electrostatic Discharge according to EN 61000 4 2 1995 Contact Discharge 4 kV Air Discharge 8 kV Radio frequency electromagnetic field according to EN 61000 4 3 1996 80 1000 MHz with 1 kHz AM 80 Modulation 3 V m Electrical fast transient burst according to EN 61000 4 4 1995 AC DC power supply 1 kV Data Signal lines 0 5 kV Surge immunity test according to EN 61000 4 5 1995 AC DC Line to Line 1 kV AC DC Line to Earth 2 kV Immunity to conducted disturbances Induce
23. rformance and boost throughput for high bandwidth applications With 32 48 Gigabits of throughput bandwidth these switches provide the quickest solution to meeting the growing demands on your network Features and Benefits Auto negotiation supported on all ports e Automatic MDI MDI X operation IEEE IEEE 802 3 2002 compliance ensures compatibility with standards based hubs switches and cards from any vendor Store and forward switching ensures error free transmission e Half and full duplex flow control prevents packets from being dropped under heavy loading Plug and play nothing to configure At a glance LEDs for port and system status monitoring Desktop or rack installation INTRODUCTION Front Panel RJ 45 Ports The EZ Switch 10 100 1000 features 16 24 1000BASE T ports with RJ 45 connectors located on the front panel of the switch Because all ports support automatic MDI MDI X operation you can use straight through cables for all network connections to PCs or servers or to other switches or hubs Front Panel LEDs The front panel of the switch provides status LEDs for at a glance system monitoring The following table details the functions of the various indicators Port and System Status LEDs LED Condition Status Power On The switch is recetving power Off The switch is not receiving power Ports Link Act On The port has established a valid network
24. rounding type with NEMA 5 15P 15 A 125 V or NEMA 6 15P 15 A 250 V configuration Denmark The supply plug must comply with Section 107 2 D1 Standard DK2 1a or DK2 5a Switzerland The supply plug must comply with SEV ASE 1011 U K The supply plug must comply with BS1363 3 pin 13 A and be fit ted with a 5 A fuse which complies with BS1362 The mains cord must be lt HAR gt or lt BASEC gt marked and be of type HO3VVF3GO 75 minimum Europe The supply plug must comply with CEE7 7 SCHUKO The mains cord must be lt HAR gt or lt BASEC gt marked and be of type HO3VVF3GO 75 minimum IEC 320 receptacle Veuillez lire fond l information de la s curit suivante avant d installer le Switch AVERTISSEMENT L installation et la d pose de ce groupe doivent tre confi s un personnel qualifi Ne branchez pas votre appareil sur une prise secteur alimentation lectrique lorsqu il n y a pas de connexion de mise la terre mise la masse COMPLIANCES Vous devez raccorder ce groupe une sortie mise la terre mise la masse afin de respecter les normes internationales de s curit Le coupleur d appareil le connecteur du groupe et non pas la prise murale doit respecter une configuration qui permet un branchement sur une entr e d appareil EN 60320 TEC 320 La prise secteur doit se trouver proximit de l appareil et son acc s doit tre
25. sic working knowledge of LANs Local Area Networks The unit must be connected to an earthed grounded outlet to comply with international safety standards Do not connect the unit to an A C outlet power supply without an eatth ground connection The appliance coupler the connector to the unit and not the wall plug must have a configuration for mating with an EN 60320 TEC 320 appliance inlet The socket outlet must be near to the unit and easily accessible You can only remove power from the unit by disconnecting the power cord from the outlet This unit operates under SELV Safety Extra Low Voltage conditions according to IEC 60950 The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions COMPLLANCES vi France and Peru only This unit cannot be powered from IT supplies If your supplies are of IT type this unit must be powered by 230 V 2P T via an isolation transformer ratio 1 1 with the secondary con nection point labelled Neutral connected directly to earth ground 1 Imp dance la terre Power Cord Set U S A and Canada The cord set must be UL approved and CSA certified The minimum specifications for the flexible cord are No 18 AWG not longer than 2 meters or 16 AWG Type SV or SJ 3 conductor The cord set must have a rated current capacity of at least 10 A The attachment plug must be an earth g
Download Pdf Manuals
Related Search