SMC Networks SMCGS16-Smart User's Manual
Contents
1. CONFIGURING THE SWITCH Port Mirroring 24 You can mirror traffic from any source port to a target port for real time analysis You can then attach a logic analyzer or RMON probe to the target port and study the traffic crossing the source port in a completely unobtrusive manner Field Attributes Ports to Mirror Select the ports that you want to mirror from this section of the page A port will be mirrored when the Mirroring Enabled check box is checked Port to Mirror to The port that will duplicate or mirror the traffic on the source port Only incoming packets can be mirrored Packets will be dropped when the available egress bandwidth is less than ingress bandwidth Note Ifthe total ingress bandwidth exceeds the mirror port s egress bandwidth packets will eventually be dropped on ingress to the switch which means they will not reach the mirror port or their intended destination port Input rate limiting in conjunction with port flow control could be used to ensure that the total ingress bandwidth never exceeds the egress bandwidth WEB CONFIGURATION Web Click PORTS Port Mirroring Port Mirroring This page enables you to set up the port mirroring features of the switch to enable traffic monitoring Ports to Mirror 2 3 4 6 mm 0 0 VON 0 0 A amp m m m m NON aja 8 Port to Mirror to Figure 16 Port Mirroring Trunks Membership This page allows you to c2. Transmitted Normal Priority Packets The total number of transmitted packets that set as High Priority in the QoS settings RMON Statistics Drop Events The total number of events in which packets were dropped due to lack of resources Received Frames The total number of frames bad broadcast and multicast received Multicast Frames The total number of good frames received that were directed to this multicast address Undersize Frames The total number of frames received that were less than 64 octets long excluding framing bits but including FCS octets and were otherwise well formed Fragments The total number of frames received that were less than 64 octets in length excluding framing bits but including FCS octets and had either an FCS or alignment error Collisions The best estimate of the total number of collisions on this Ethernet segment 13 CONFIGURING THE SWITCH Table 4 Port Statistics Continued Parameter Description Received Bytes Total number of bytes of data received on the network This statistic can be used as a reasonable indication of Ethernet utilization Broadcast Frames The total number of good frames received that were directed to the broadcast address Note that this does not include multicast packets CRC Alignment Errors The number of CRC alignment errors FCS or alignment errors Oversize Frames The to
3. EA Fa A g KE Fa a g E fa A M Fa fa y fa fa 2 MH fal fas F Fa fs 14 fg fai Aa g 15 Fr fal fa y 15 MA fal fa E 1 7 fal fas Note Ports must always be a member of at least one VLAN and will always have the PVID set to an active VLAN hep army CANCEL Figure 20 VLAN Settings WEB CONFIGURATION QOS Settings QoS Quality of Service is a mechanism which is used to prioritize certain traffic as it is moves through the switch Traffic can be classified as High or Normal priority and when the switch is heavily loaded it is the Normal priority packets that are dropped first You can select how traffic is prioritized by using one of the four QoS modes which is selected using the QoS Mode drop down list Note Only one QoS mode can be active at one time It is not possible for example to prioritise traffic using the IP Port number and 802 1p tag QoS Disabled QoS is turned off and all packets have equal priority 802 1p Packets are prioritzed using the content of the VLAN tag The 802 1p field is held within the VLAN tag of a packet The field is three bits long so can hold eight values 0 7 inclusive When QoS Mode is set to 802 1p the 802 1p Configuration table appears which allows a priority normal or high to be set for each of the eight values You can use the Prioritize Traffic drop down list to quickly set the values in the 802 1p Configuration table Select All Normal Priority to set all values to norm
4. Register Product Register your product if you have not already done so Web Click System Register Product By clicking the Register Now button you will be taken to the SMC website where you can enter the products details Register Product This page allows you to register your product if you have not already done so By clicking on the Register Now button you will be taken to the SMC website where you can enter the products details Product Registration Register Now Figure 12 Register Product Port Configuration You can use the Port Configuration page to manually fix the speed duplex mode and flow control Field Attributes Speed Duplex Allows you to manually set the port speed and duplex mode e Flow Control Allows flow control to be enabled or disabled When the box is checked flow control is enabled 20 WEB CONFIGURATION Trunk Indicates if a port is a member of a trunk Web Click PORTS Settings Port Configuration This page enables you to configure each Switch port Port Configuration E Auto Speed x D 2 Auto Speed x mi 3 Auto Speed mi 4 Auto Speed o 5 Auto Speed x mi 6 Auto Speed m 7 Auto Speed x mi 8 Auto Speed mi 9 Auto Speed x ia 10 Auto Speed O 11 Auto Speed x m 12 Auto Speed Oo 13 Auto Speed 2 D 14 Auto Speed ml 15 Auto Speed mi 16 Auto Speed HELP APPLY CANCEL Figure 13 Port Configuration
5. The LAN IP Address Subnet Mask and Gateway IP Address will not be reset 18 WEB CONFIGURATION Web Click System Tools Reset to Factory Defaults Tools Tools Reset to Factory Defaults e Press the APPLY button to restart the Switch The reset will be complete when the power light stops blinking HELP amy Figure 9 Reset to Factory Defaults Upgrade Firmware Upgrades the Switch system firmware using a file provided by SMC Select Upgrade Firmware from the Tools drop down list then click on the Browse button to select the firmware file Finally press the APPLY button to upgrade the selected Switch firmware file You can download firmware files for your Switch from the Support section of www smc com Web Click System Tools Reset to Factory Defaults Tools e Press the APPLY button to upgrade the selected Switch firmware file e You can download firmware files for your Switch from the Support section of www smc corn HELP APPLY Figure 10 Upgrade Firmware Restart Switch Web Click SYSTEM Tools Restart Switch To restart the switch select from the Tools drop down list and then click APPLY The reset will be complete when the user interface displays the login page 19 CONFIGURING THE SWITCH Tools Tools Restart Switch e Press the APPLY button to restart the Switch The reset will be complete when the power light stops blinking HELP APPLY Figure 11 Restart Switch
6. Configuring Rate Limits This function allows the network manager to control the maximum rate for traffic transmitted or received on an interface Rate limiting is configured on interfaces at the edge of a network to limit traffic into or out of the switch Traffic that falls within the rate limit is transmitted while packets that exceed the acceptable amount of traffic are dropped Rate limiting can be applied to individual ports or trunks When an interface is configured with this feature the traffic rate will be monitored by the hardware to verify conformity Non conforming traffic is dropped conforming traffic is forwarded without any changes 21 CONFIGURING THE SWITCH The Input Output Bandwidth Limit field is a type in box which accepts an integer number in the range 1 to 100 The number specifies the percentage of the total input bandwidth of the port that can be used before packets are dropped or flow control starts Web Click PORTS Rate Limiting This page enables you to set the rate limiting parameters for each port on the Switch Rate Limiting This page enables you to set the rate limiting parameters for each port on the Switch Rate Limiting Enable Enable Limiting Limiting 1 100fidx m ET O 2 Auto i po mi 3 Auto O LE O 4 Auto D ET m 5 Auto E ET mi 6 Auto m Be m 7 Auto mj EE mi 8 a o o 9 Auto O ET ui 10 Auto mi ET m 11 Auto m ET Oo 12 Auto 5 EC m 13 Auto m E 14 Auto D ET O 15 Auto O
7. ETT O 16 Auto Oo Bo Oo Hep army canca Figure 14 Rate Limiting 22 WEB CONFIGURATION Port Broadcast Control Broadcast storms may occur when a device on your network is malfunctioning or if application programs are not well designed or properly configured If there is too much broadcast traffic on your network performance can be severely degraded or everything can come to complete halt You can protect your network from broadcast storms by setting a threshold for broadcast traffic for each port Any broadcast packets exceeding the specified threshold will then be dropped Field Attributes Enable Broadcast Storm Control Click to select the boxt to enable Broadcast Storm Control e Bandwidth Limit Threshold as percentage of port bandwidth This field accepts an integer value in the range 1 to 100 The value specifies the percentage of the available input bandwidth that can be made available for broadcast and multicast traffic The same percentage threshold is applied to every port on the switch When the threshold is exceeded packets are dropped irrespective of the flow control settings Web Click PORTS Broadcast Control This page enables you to set the broadcast storm control parameters for every port on the Switch Port Broadcast Control This page enables you to set the broadcast storm control parameters for every port on the Switch HELP APPLY CANCEL Figure 15 Port Broadcast Control 23
8. FAILURE OR INTERRUPTION OF ITS PRODUCTS EVEN IF SMC OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS WHICH MAY VARY FROM STATE TO STATE NOTHING IN THIS WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS SMC will provide warranty service for one year following discontinuance from the active SMC price list Under the limited lifetime warranty internal and external power supplies fans and cables are covered by a standard one year warranty from date of purchase SMC Networks Inc 38 Tesla Irvine CA 92618 COMPLIANCES COMPLIANCES FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television recep
9. ea a ee 6 Main Menu Meran sents Scone esas EB 7 Web Configurations 22023 ai 8 Displaying Status Overview 8 Showing Port Statistics 12 Displaying System Name 15 Setting the Switch s IP Address 16 Configuring the Logon Password 17 LO OLS RER Ay Sythe cath es a Min een ae Ae T 18 Register Product leida ne RE RAD eh 20 Port Configuration a mins ar ut 20 Configuring Rate Limits 21 Port Broadcast Control nat 23 Pott Mirroring an enger seen 24 Trunks Membership 25 Trunk Configuration 2 ee A 26 Trunk Rate Limit 2 222 208 ee 27 VEANISELUNDSS dae cid ee A RER ln Bl 28 QOS Settings noise ar a a a ade E 31 Troubleshooting us en 34 Diagnosing Switch Indicators 34 Changing PC s IP Address 36 viii Product Specifications EZ Switch 10 100 1000 FEATURES AND BENEFITS INTRODUCTION The EZ Switch 10 100 1000 SMCGS16 Smart and SMCGS24 Smart are high performance web managed smart switches for delivering performance and control to your network They provide 16 24 full duplex 1000BASE T ports that significantly improve network performance and boost throughput using Smart features configured on the web interface With 32 48 Gi
10. sont AWG No 18 ou AWG No 16 pour une longueur infe rieure a 2 me tres type SV ou SJ 3 conducteurs Le cordon doit tre en mesure d acheminer un courant nominal d au moins 10 A La prise femelle de branchement doit tre du type mise la terre mise la masse et respecter la configuration NEMA 5 15P 15 125 V ou NEMA 6 15P 15 A 250 V Danemark La prise m le d alimentation doit respecter la section 107 2 D1 de la norme DK2 1a ou DK2 5a vi COMPLIANCES viii Cordon lectrique Il doit tre agr dans le pays d utilisation Suisse La prise m le d alimentation doit respecter la norme SEV ASE 1011 Europe La prise secteur doit tre conforme aux normes CEE 7 7 SCHU KO LE cordon secteur doit porter la mention lt HAR gt ou lt BASEC gt et doit tre de type HO3VVF3GO 75 minimum Bitte unbedingt vor dem Einbauen des RPU die folgenden Sicherheitsanweisungen durchlesen WARNUNG Die Installation und der Ausbau des Gerats darf nur durch Fachpersonal erfolgen Diese Anleitung ist fr die Benutzung durch Netzwerkadministratoren vorgesehen die fr die Installation und das einstellen von Netzwerkkomponenten verantwortlich sind sie setzt Erfahrung bei der Arbeit mit LANs Local Area Networks voraus Das Ger t sollte nicht an eine ungeerdete Wechselstromsteckdose angeschlossen werden Das Ger t mu an eine geerdete Steckdose a
11. their facility to SMC SMC is responsible for return shipping charges from SMC to customer it WARRANTIES EXCLUSIVE IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE CUSTOMER S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN QUESTION AT SMC S OPTION THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS EXPRESS OR IMPLIED EITHER IN FACT OR BY OPERATION OF LAW STATUTORY OR OTHERWISE INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE OR USE OF ITS PRODUCTS SMC SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER S OR ANY THIRD PERSON S MISUSE NEGLECT IMPROPER INSTALLATION OR TESTING UNAUTHORIZED ATTEMPTS TO REPAIR OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE OR BY ACCIDENT FIRE LIGHTNING OR OTHER HAZARD LIMITATION OF LIABILITY IN NO EVENT WHETHER BASED IN CONTRACT OR TORT INCLUDING NEGLIGENCE SHALL SMC BE LIABLE FOR INCIDENTAL CONSEQUENTIAL INDIRECT SPECIAL OR PUNITIVE DAMAGES OF ANY KIND OR FOR LOSS OF REVENUE LOSS OF BUSINESS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE USE PERFORMANCE
12. 006 65 238 6556 82 2 553 0860 81 45 224 2332 61 2 8875 7887 91 22 8204437 Fax 949 679 1481 Fax 34 93 477 3774 Fax 44 0 1234 831 413 Fax 33 0 45 34 68 58 Fax 39 02 739 14 17 Fax 31 0 172 242 393 Fax 49 0 89 92861 230 Fax 45 0 566 622 86 Fax 420 266 794 423 Fax 34 93 471 3374 Fax 34 93 477 3774 Fax 34 93 477 3774 Fax 86 10 6235 4962 Fax 886 2 8797 6288 Fax 65 238 6466 Fax 82 2 553 7202 Fax 81 45 224 2331 Fax 61 2 8875 7777 Fax 91 22 8204443 If you are looking for further contact information please visit www smc com SMC Networks 38 Tesla Irvine CA 92618 Phone 949 679 8000 Model Numbers SMCGS16 Smart SMCGS24 Smart Publication Number 149100007600H E082005 RO1
13. 100 1000M Trunk Status An indication of the speed and duplex setting of the CONFIGURING THE SWITCH trunk This is a number the speed in Mbps followed by either Full for full duplex or Half for half duplex This can be changed on the TRUNKS gt Settings page e Ports The ports that are members of the trunk VLAN Inoformation e VLAN ID A number in the range 1 4094 which identifies the VLAN VLAN Member A list of the ports that are members of the VLAN By default all ports are members of VLAN 1 10 WEB CONFIGURATION Web Click STATUS Overview Status Overview This page displays the status of your Switch System Information SMCGS16 Smart Number of Ports 16 ROL 1 00 03 5529000044 1 192 168 2 10 255 255 255 0 0 0 0 0 00 01 c1 00 00 01 7 10 100 1000M Up 100fdx Disabled Enabled all a 2 10 100 1000M Down Auto Disabled Enabled All 1 3 10 100 1000M Down Auto Disabled Enabled All al 4 10 100 1000M Down Auto Disabled Enabled All 1 5 10 100 1000M Down Auto Disabled Enabled All 6 10 100 1000M Down Auto Disabled Enabled all 1 F 10 100 1000M Down Auto Disabled Enabled All 1 8 10 100 1000M Down Auto Disabled Enabled All 1 9 10 100 1000M Down Auto Disabled Enabled All 1 10 10 100 1000M Down Auto Disabled Enabled All E 11 10 100 1000M Down Auto Disabled Enabled All 1 12 10 100 1000M Down Auto Disabled Enabled All 1 13 10 100 1000M Down Auto Disabled Enabled All 1 14 10 100 1000M
14. Attributes Trunk Indicates trunk identification Speed Duplex Allows you to manually set the port speed and duplex mode for all ports in the trunk e Flow Control Allows flow control to be enabled or disabled When the box is checked flow control is enabled e Ports Indicates which ports belong to the trunk 26 WEB CONFIGURATION Web Click TRUNKS Settings Trunk Configuration This page enables you to configure each Trunk configured on the Switch Port Configuration Speed Duplex Flow Control TL Auto Speed y oO 23 HELP APPLY CANCEL Figure 18 Trunk Configuration Trunk Rate Limit This page allows you to change the maximum data rate into and out of each trunk on the switch Field Attributes Trunk Indicates trunk identification Trunk Speed Indicates the trunk speed Enable Input Rate Limiting Click to select the box to enable the Input Rate Limiting function Input Limit Enter the desired limit of port speed Enable Output Rate Limiting Click to select the box to enable the Output Rate Limiting function e Output Limit Enter the desired limit Yo of port speed e Ports Indicates which ports belong to the trunk 27 CONFIGURING THE SWITCH Web Click TRUNKS Settings Rate Limiting This page enables you to set the rate limiting parameters for each Trunk configured on the Switch Rate Limiting a Auto mj fo m 30 2 3 Figur
15. Down Auto Disabled Enabled All 1 15 10 100 1000M Down Auto Disabled Enabled All 1 16 10 100 1000M Down Auto Disabled Enabled All 1 Trunk Information No Trunks Configured VLAN Information Trunk 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 __Hap ReRe Figure 3 Switch Information 11 CONFIGURING THE SWITCH Showing Port Statistics 12 You can display statistics on network traffic from the ports These statistics can be used to identify potential problems with the switch such as a faulty port or unusually heavy loading All values displayed have been accumulated since the last system reboot but can be reset to zero by clicking the CLEAR button The current statistics are not displayed until you click the REFRESH button Table 4 Port Statistics Parameter Description Interface Statistics Received Octets The total number of octets received on the interface including framing characters Received Unicast Packets The number of subnetwork unicast packets delivered to a higher layer protocol Received Errors The number of inbound packets that contained errors preventing them from being deliverable to a higher layer protocol Transmitted Multicast Packets The total number of packets that higher level protocols requested be transmitted and which were addressed to a multicast address at this sub layer including those that were discarded or not sent Transmitted Bro
16. EZ Switch 10 100 1000 Web Managed Smart Switch User friendly web management interface Supports Qos VLANs and Trunk configuration Automatic MDI MDI X operation Store and forward switching ensures error free transmission Half and full duplex flow control prevents packets from being dropped under heavy loading Plug and play Optional configuration using web interface At a glance LEDs for port and system status monitoring Desktop or rack installation SMC Management Guide hz _ SMCGS16 Smart Networks SMCGS24 Smart EZ Switch 10 100 1000 Management Guide From SMC s EZ line of low cost workgroup LAN solutions SMC Networks 38 Tesla August 2005 Irvine CA 92618 Phone 949 679 8000 Pub 149100007600H Information furnished by SMC Networks Inc SMC is believed to be accurate and reliable However no responsibility is assumed by SMC for its use nor for any infringements of patents or other rights of third parties which may result from its use No license is granted by implication or otherwise under any patent or patent rights of SMC SMC reserves the right to change specifications at any time without notice Copyright 2005 by SMC Networks Inc 38 Tesla Irvine CA 92618 All rights reserved Printed in Taiwan Trademarks SMC is a registered trademark and EZ Switch TigerStack and TigerSwitch are trademarks of SMC Networks Inc Other product and company names are trademarks or regi
17. GS16 Smert HELP APPLY CANCEL Figure 6 System Name Setting the Switch s IP Address 16 This section describes how to configure an IP interface for management access over the network The IP address for this switch is 192 168 2 10 by default To manually configure an address you need to change the switch s default settings IP address 192 168 2 10 and netmask 255 255 255 0 to values that are compatible with your network You may also need to a establish a default gateway between the switch and management stations that exist on another network segment Field Attributes e LAN IP Address Address of the VLAN interface that is allowed management access Valid IP addresses consist of four numbers 0 to 255 separated by periods Default 192 168 2 10 Subnet Mask This mask identifies the host address bits used for routing to specific subnets Default 255 255 255 0 Gateway IP Address IP address of the gateway router between this device and management stations that exist on other network segments Default 0 0 0 0 Note If at any point you cannot remember the switch s IP address you can restore the original settings by following the procedure described in the Troubleshooting section WEB CONFIGURATION Manual Configuration Web Click System LAN Settings Enter the IP address subnet mask and gateway then click APPLY LAN Settings This page allows you to configure the address of the
18. IDs VLAN membership PVID and Packet Type Note that the ports within a Trunk cannot be configured individually configure the Trunk instead Trunks are labelled T1 to T8 Field Attributes e Port Trunk The front panel port number of the port or the ID of a trunk This cannot be changed VLAN ID VLAN to which matching protocol traffic is forwarded VLAN 1 is a special VLAN it cannot be deleted and if there is a possibility that a port could become isolated the Web USer interface will add the port to VLAN 1 You can add up to seven VLANs to the configuration of the switch Each VLAN must be given a VLAN ID in the range 2 4094 One port can be a member of up to eight VLANs All packets travelling through the switch are associated with one and only one VLAN If a port is not a member of a VLAN it cannot send or receive packets associated with that VLAN A tagged packet carries its VLAN ID in the payload of the packet An untagged packet received on a port with Packet Type set to All is associated with the VLAN identified by the PVID PVID VLAN ID assigned to untagged frames received on the interface The PVID is Port VLAN ID is the VLAN ID that is associated with untagged ingress packets It is not possible to remove a port from VLAN 1 unless its PVID has been changed to something other than 1 The PVID has no effect on ports that have Packet Type set to Tagged Default 1 e Packet Type Sets the interface to acc
19. RE ARAS VCC ORB ID OTRA MBE EC TORE tAE CEA a EE HEZZILERIFLEHNBUET COBRAR FKEDBRENSCEMBVETF COMPLIANCES Please read the following safety information carefully before installing the Switch WARNING Installation and removal of the unit must be carried out by qualified personnel only e This guide is intended for use by network administrators who are responsible for setting up and installing network equipment consequently it assumes a basic working knowledge of LANs Local Area Networks e The unit must be connected to an earthed grounded outlet to comply with international safety standards e Do not connect the unit to an A C outlet power supply without an earth ground connection The appliance coupler the connector to the unit and not the wall plug must have a configuration for mating with an EN 60320 IEC 320 appliance inlet The socket outlet must be near to the unit and easily accessible You can only remove power from the unit by disconnecting the power cord from the outlet e This unit operates under SELV Safety Extra Low Voltage conditions according to IEC 60950 The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions COMPLIANCES vi France and Pern only This unit cannot be powered from IT supplies If your supplies are of IT type this unit must be powered by 230 V 2P T via an isolation transformer ratio 1 1 with the seconda
20. Web Management interface of your Switch on you LAN HELP APPLY CANCEL Figure 7 LAN Settings Configuring the Logon Password The administrator has write access for all parameters governing the onboard agent You should therefore assign a new administrator password as soon as possible and store it in a safe place Field Attributes e Password Specifies the user password Range 1 16 characters plain text case sensitive Note If at any point you cannot remember the password you can restore the original settings by following the procedure described in the Troubleshooting section 17 CONFIGURING THE SWITCH Web Click System Password To change the password for the administrator enter current password the new password confirm it by entering it again then click APPLY Password Settings Set a password to secure access to the Switch Web Management Interface Change Password Note The password is case sensitive Note If you forget your password the only way to reset it is to reset the Switch s entire configuration to factory defaults Hep lle cancer Figure 8 Password Settings Tools On Tools page you can restore the switch to default settings upgrade the firmware of the switch or restart the switch Restore to Factory Defaults Force the Switch to restore the original factory settings To reset the switch select Reset to Factory Defaults from the drop down list and click APPLY
21. according to EN 61000 4 2 1995 Contact Discharge 4 kV Air Discharge 8 kV Radio frequency electromagnetic field according to EN 61000 4 3 1996 80 1000 MHz with 1 kHz AM 80 Modulation 3 V m Electrical fast transient burst according to EN 61000 4 4 1995 AC DC power supply 1 kV Data Signal lines 0 5 kV Surge immunity test according to EN 61000 4 5 1995 AC DC Line to Line 1 kV AC DC Line to Earth 2 kV e Immunity to conducted disturbances Induced by radio frequency fields EN 61000 4 6 1996 0 15 80 MHz with 1 kHz AM 80 Modulation 3 V m Power frequency magnetic field immunity test according to EN 61000 4 8 1993 1 A m at frequency 50 Hz e Voltage dips short interruptions and voltage variations immunity test according to EN 61000 4 11 1994 gt 95 Reduction 10 ms 30 Reduction 500 ms gt 95 Reduction 5000 ms LVD EN 60950 1 2001 Industry Canada Class A This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference causing equipment standard entitled Digital Apparatus ICES 003 of the Department of Communications Cet appareil num rique respecte les limites de bruits radio lectriques applicables aux appareils num riques de Classe A prescrites dans la norme sur le mat riel brouilleur Appareils Num riques NMB 003 dict e par le minist re des Communications Japan VCCI Class A COEM MEME SE
22. adcast Packets The total number of packets that higher level protocols requested be transmitted and which were addressed to a broadcast address at this sub layer including those that were discarded or not sent Received High Priority Packets The total number of received packets that set as High Priority in the QoS settings Transmitted High Priority Packets The total number of transmitted packets that set as High Priority in the QoS settings Received Multicast Packets The number of packets delivered by this sub layer to a higher sub layer which were addressed to a multicast address at this sub layer WEB CONFIGURATION Table 4 Port Statistics Continued Parameter Description Received Broadcast Packets The number of packets delivered by this sub layer to a higher sub layer which were addressed to a broadcast address at this sub layer Transmitted Octets The total number of octets transmitted out of the interface including framing characters Transmitted Unicast Packets The total number of packets that higher level protocols requested be transmitted to a subnetwork unicast address including those that were discarded or not sent Transmitted Errors The number of outbound packets that could not be transmitted because of errors Received Normal Priority Packets The total number of received packets that set as High Priority in the QoS settings
23. al priority or select All High Priority to set all values to high priority Use Custom if you want to set each value individually Note Because end stations like PCs are not usually VLAN aware they do not create VLAN tagged frames As a result this method of prioritization is not ideal when there are a lot of PCs connected to the Switch IP Port Although this is a layer 2 switch it is capable to looking far enough into each packet to find the port number associated with a UDP IP or TCP IP transfer When QoS Mode is set to IP Port the Custom QoS TCP IP 31 CONFIGURING THE SWITCH 32 table appears and you are able to select up to ten IP Ports for prioritization Prioritized port numbers can be in the range 0 65535 inclusive The specified ports will be given either normal or high priority depending on the value selected in the Priority drop down list If the specified port numbers are given high priority all other port numbers will have normal priority Conversely if the specified port numbers are given normal priority all other port numbers will have high priority it is therefore possible to increase or decrease the priority of the specifified IP Port numbers relative to all other traffic To quickly populate the Custom QoS TCP IP table use the Prioritize Traffic drop down list The list contains some useful presets Note Because the use of TCP IP and UDP IP is so widespread this method of traffic prioritization is mos
24. art 400 Kbits on chip frame buffer Power Consumption SMCGS16 Smart 15 8 Watts SMCGS24 Smart 24 2 Watts Heat Dissipation 130 BTU hr maximum Power Requirement Input Voltage 100 240 VAC 50 60 Hz Temperature Operating 0 40 C 32 104 F Storage 40 70 C 40 158 F Humidity 5 to 95 non condensing EMC Safety Compliances CE Mark Immunity EN 61000 4 2 3 4 5 6 8 11 Emissions FCC Class A CISPR Class A EN 61000 3 2 3 Safety CSA CUS CSA60950 1 amp UL60950 1 TUV GS EN60950 1 CB IEC60950 1 FOR TECHNICAL SUPPORT CALL From U S A and Canada 24 hours a day 7 days a week 800 SMC 4 YOU Phn 949 679 8000 Fax 949 679 1481 From Europe Contact details can be found on www smc com INTERNET E mail addresses techsupport smc com Driver updates http www smc com index cfm action tech support drivers downloads World Wide Web http www smc com FOR LITERATURE OR ADVERTISING RESPONSE CALL U S A and Canada Spain UK France Italy Benelux Central Europe Nordic and Baltics Eastern Europe Sub Saharian Africa North West Africa CIS PRC Taiwan Asia Pacific Korea Japan Australia India 800 SMC 4 YOU 34 91 352 00 40 44 0 871 277 98 02 33 0 1 55 64 04 55 39 02 739 12 68 31 0 654 776 790 49 0 89 92861 0 46 0 566 622 83 420 266 794 421 27 012 661 0232 34 93 477 4920 34 93 477 4920 86 10 6235 4958 886 2 8797 8
25. ctured in such a way as to allow for the recovery and disposal of all included electrical components once the product has reached the end of its life Manufacturing Materials There are no hazardous nor ozone depleting materials in this product Documentation All printed documentation for this product uses biodegradable paper that originates from sustained and managed forests The inks used in the printing process ate non toxic Purpose This guide details the hardware features of the switch including Its physical and performance related characteristics and how to install the switch Audience The guide is intended for use by network administrators who are responsible for installing and setting up network equipment consequently it assumes a basic working knowledge of LANs Local Area Networks Diese Anleitung ist f r die Benutzung durch Netzwerkadministratoren vorgesehen die f r die Installation und das einstellen von Netzwerkkomponenten verantwortlich sind sie setzt Erfahrung bei der Arbeit mit LANs Local Area Networks voraus T ABLE OF CONTENTS Introductions AAA 1 Reatutestand Benefits 22e nee a ir te ere DR 1 Initial Configuration 2 Configuring the Switch 4 Using the Webinterface nam als ete nes 4 Navigating the Web Browser Interface 5 Home Parr ida ea 5 Configuration Options ya jade a HA hyde da SE nf Me 6 Panels pla Mead sit asa
26. e 19 Trunk Rate Limiting VLAN Settings 28 You can configure VLAN behavior for specific interfaces including the default VLAN identifier PVID and accepted frame types This page allows you to create and delete VLANs Virtual LANs and to change the VLAN membership and behaviour of individual ports VLANs are powerful but can be difficult to set up properly Each row of the table corresponds to one port or trunk trunked ports cannot be configured individually Introduction to VLANs VLANs or Virtual LANs are logical partitions of the physical LAN You can use VLANs to increase network performance or increase internal network security If the network has adequate performance and security for your current needs it is recommended that you leave the VLAN settings in the default configuration The default configuration is as follows e All ports are members of VLAN 1 The switch management interface is on VLAN 1 this cannot be changed All ports have a Port VLAN ID PVID of 1 WEB CONFIGURATION e All ports can send and receive both VLAN tagged and untagged packets e they are hybrid ports In the default configuration any port is able to send traffic to any other port and a PC connected to any port will be able ro reach the management interface Broadcast traffic for example will be flooded to all ports on the switch There are three different parameters that can be configured for each port on the switch VLAN
27. ept all frame types including 29 CONFIGURING THE SWITCH 30 tagged or untagged frames or only tagged frames When set to receive all frame types any received frames that are untagged are assigned to the default VLAN PCs should be connected to ports with Packet Type set to All PCs cannot in general send or receive tagged packets Switches should be connected to each other with Packet Type set to Tagged If the Packet Type is set to All the port can accept incoming tagged and untagged packets Untagged packets will be associated with the VLAN identified by the PVID Tagged packets will be dropped unless the port is a member of the VLAN identified by the VLAN tag in the packet Outgoing packets will be tagged unless the packet s VLAN ID is the same as the PVID If the Packet Type is set to Tagged the port will drop untagged packets and will only send and receive tagged packets Tagged packets will be dropped unless the port is a member of the VLAN identified by the VLAN tag in the packet The PVID has no effect in this case Option All Tagged Default All Web Click VLANS VLAN Settings Fill in the required settings for each interface click Apply VLAN Settings This page allows the configuration of VLANs on the switch for both Ports and Trunks Static Table Settings VLAN IDs 00 aoo ano ano ano ano _avo A a Fa a p EI F FE fz F Fa fa y E Fa a g Ei Fa Aa y
28. g a web browser you can configure the switch and view statistics to monitor network activity The web agent can be accessed by any computer on the network using a standard web browser Internet Explorer 5 5 or above or Mozilla Firefox 1 0 or above Prior to accessing the switch from a web browser be sure you have first performed the following tasks 1 Configure the switch with a valid IP address subnet mask and default gateway Default 192 168 2 10 255 255 255 0 0 0 0 0 See Initial Configuration on page 2 2 Set a new password using the web interface Default smcadmin Access to the web interface is controlled by the password See Configuring the Logon Password on page 15 Note If at any point you cannot remember the switch s IP address you can restore the original settings by following the procedure described in the Troubleshooting section NAVIGATING THE WEB BROWSER INTERFACE Navigating the Web Browser Interface To access the web browser interface you must first enter a password The user has Read Write access to all configuration parameters and statistics The default password for the switch is smcadmin If user input is not detected within five minutes the current session will be terminated Home Page When your web browser connects with the switch s web agent the home page is displayed as shown below The home page displays the Main Menu on the left side of the screen and System Inf
29. gabits of throughput bandwidth these switches provide the quickest solution to meeting the growing demands on your network Features and Benefits e User friendly web management interface e Supports Qos VLANs and Trunk configuration Store and forward switching ensures error free transmission e Half and full duplex flow control prevents packets from being dropped under heavy loading Plug and play Optional configuration using web interface At a glance LEDs for port and system status monitoring e Desktop or rack installation INITIAL CONFIGURATION INITIAL CONFIGURATION To make use of the management features of your SMC Smart Switch you must first give it an IP address For simplicity this should be done before you permanently install the switch in the network The following procedure is recommended 1 Place your Smart Switch close to the PC that you will use to configure it It will help if you can see the front panel of the switch while working on your PC Connect the Ethernet port of your PC to any port on the front panel of your Smart Switch start your PC if it is not already running connect power to the switch and when your PC has finished its start up sequence verify that you have a link by checking the LEDs on the front panel of the switch see the Hardware Description for more information The default IP address of the switch is 192 168 2 10 and the subnet mask is 255 255 255 0 If you
30. nel Display The web agent displays an image of the switch s ports The port will turn green when the corresponding front panel port is in connection with another device To show the port number place mouse pointer onto the intended port SMC SMC DER Eikon Networks Figure 2 Front Panel Indicators Main Menu NAVIGATING THE WEB BROWSER INTERFACE Using the onboard web agent you can define system parameters manage and control the switch and all its ports or monitor network conditions The following table briefly describes the selections available from this program Table 2 1 Switch Main Menu Menu Description Page STATUS 6 Overview Provides basic system description including 6 system information address information port information trunk information and VLAN information Statistics Shows statistics for port interface and 10 RMON SYSTEM 13 Name Shows the name of the switch 13 LAN Settings Sets LAN IP address subnet mask and 14 gateway IP address Password Changes password 15 Tools 16 Restore to Factory Force the Switch to perform a power reset 16 Defaults and restore the original factory settings Upgrade Firmware Upgrade the Switch system firmware using a 17 file provided by SMC Restart Restarts the switch 17 Register Product Registers the switch online 18 PORTS 18 Settings Configure the speed and duplex mode of the 18 port Rate Limiting Sets the
31. ngeschlossen werden welche die internationalen Sicherheitsnormen erf llt Der Ger testecker der Anschlu an das Ger t nicht der Wandsteckdosenstecker mu einen gem EN 60320 IEC 320 konfigurierten Ger teeingang haben Die Netzsteckdose mu in der N he des Ger ts und leicht zug nglich sein Die Stromversorgung des Ger ts kann nur durch Herausziehen des Ger tenetzkabels aus der Netzsteckdose unterbrochen werden Der Betrieb dieses Ger ts erfolgt unter den SELV Bedingungen Sicherheitskleinstspannung gem IEC 60950 Diese Bedingungen sind nur gegeben wenn auch die an das Ger t angeschlossenen Ger te unter SELV Bedingungen betrieben werden COMPLIANCES Stromkabel Dies muss von dem Land in dem es benutzt wird gepr ft werden Schweiz Dieser Stromstecker mu die SEV ASE 1011Bestimmungen ein halten Europe Das Netzkabel mu vom Typ HO3VVF3GO 75 Mindestan forderung sein und die Aufschrift lt HAR gt oder lt BASEC gt tragen Der Netzstecker mu die Norm CEE 7 7 erf llen SCHUKO Warnings and Cautionary Messages Warning Warning Warning Caution Caution Caution This product does not contain any serviceable user parts Installation and removal of the unit must be carried out by qualified personnel only When connecting this device to a power outlet connect the field ground lead on the tri pole power plug to a valid earth ground line to prevent electrical ha
32. nologies At that point the obsolete product is discontinued and is no longer an Active SMC product A list of discontinued products with their respective dates of discontinuance can be found at http www smc com index cfm action customer_service_warranty All products that are replaced become the property of SMC Replacement products may be either new or reconditioned Any replaced or repaired product carries either a 30 day limited warranty or the remainder of the initial warranty whichever is longer SMC is not responsible for any custom software or firmware configuration information or memory data of Customer contained in stored on or integrated with any products returned to SMC pursuant to any warranty Products returned to SMC should have any customer installed accessory or add on components such as expansion modules removed prior to returning the product for replacement SMC is not responsible for these items if they are returned with the product Customers must contact SMC for a Return Material Authorization number prior to returning any product to SMC Proof of purchase may be required Any product returned to SMC without a valid Return Material Authorization RMA number clearly marked on the outside of the package will be returned to customer at customer s expense For warranty claims within North America please call our toll free customer support number at 800 762 4968 Customers ate responsible for all shipping charges from
33. onnections Right click the connectin icon of which the IP address you want to change and then click properties In General tab under Components checked are used by this connection click to select Internet Protocol TCP IP and then click Properties to open Internet Protocol TCP IP Properties dialog box In Internet Protocol TCP IP Properties dialog box click to select Use the following IP address In IP address Subnet mask and Default gateway type your intended information Click OK to save the changes and quit EZ Swircu 10 100 1000 PRODUCT SPECIFICATIONS EZ Switch 10 100 1000 Standards Conformance IEEE 802 3 2002 Ethernet Fast Ethernet Gigabit Ethernet Full duplex flow control Communication Rate 10 100 and 1000 Mbps Communication Mode Full or half duplex at 10 100 Mbps Full duplex at 1000 Mbps Media Supported 10BASE T 100 ohm Category 3 or better twisted pair 100BASE TX 100 ohm Category 5 or better twisted pair 1000BASE T 100 ohm Category 5 5e or 6 twisted pair Number of Ports SMCGS16 Smart 16 RJ 45 1000BASE T ports SMCGS24 Smart 24 RJ 45 1000BASE T ports Indicator Panel Power Ports Link Act 100 1000M Dimensions 33 x 20 4 x 4 4 cm 12 99 x 8 04 x 1 73 in 37 PRODUCT SPECIFICATIONS 38 Weight SMCGS16 Smart 2 0 kg 4 04 lbs SMCGS24 Smart 2 2 kg 4 85 lbs MAC Address Table 8 K entries Memory Buffer SMCGS16 Smart 272 Kbits on chip frame buffer SMCGS24 Sm
34. ormation on the right side The Main Menu links are used to navigate to other menus and display configuration parameters and statistics Status Overview This page displays the status of your Switch SMCGS16 Smart 16 ROL 1 00 03 5529000044 1 192 168 2 10 255 255 255 0 0 0 0 0 00 01 c1 00 00 01 1 100f x Disabled Enabled all 10 100 1000M Up 2 10 100 1000M Down Auto Disabled Enabled All t Figure 1 Home Page Note The examples in this chapter are based on the SMCGS16 Smart Other than the number of fixed ports there are no major differences between the SMCGS16 Smart and SMCGS24 Smart CONFIGURING THE SWITCH Configuration Options Configurable parameters have a dialog box or a drop down list Once a configuration change has been made on a page be sure to click on the Apply button to confirm the new setting The following table summarizes the web page configuration buttons Table 2 Web Page Configuration Buttons Button Action Apply Sets specified values to the system Cancel Discards all changes and restores current values Help Links directly to web help Notes To ensure proper screen refresh be sure that Internet Explorer is configured as follows Under the menu Tools Internet Options General Temporary Internet Files Settings the setting for item Check for newer versions of stored pages should be Every visit to the page Pa
35. power outlet by using it for another device Replace the AC power cord Symptom Link LED does not light after connection is made Probable Causes Switch port network card or cable may be defective Possible Solutions Check that the switch and attached device are both powered on Be sure the network cable is connected to both devices Verify that Category 5 or better cable is used for 10 100 Mbps connections Category 5 or 5e cable for 1000 Mbps connections and that the length of any cable does not exceed 100 meters 328 feet Check the network card and cable connections for defects Replace the defective card or cable if necessary DIAGNOSING SWITCH INDICATORS 3 Forgotten password If you have forgotten the administration password you can return the Switch to its factory default state by dong the following 1 Remove the power cord from the back of the Switch 2 Remove all cables from the front panel ports 3 Connect port 1 to port 2 on the front panel using a standard network cable 4 Reconnect the power cord to the rear of the Switch 5 Wait at least 40 seconds before disconnecting port 1 from port 2 After completing this procedure the password will be smcadmin and the network address will be returned to the default 192 168 2 10 35 CHANGING PCs IP ADDRESS CHANGING PC s IP ADDRESS 36 To change the IP address of your PC On Windows go to Start Settings Network and Dial up C
36. r PC has a different address from the switch but is on the same subnet i e the PC and switch both have addresses that start 192 168 2 x but are different thereafter you can skip directly to step 4 Otherwise you will have to set your PC s IP address manually If you are unfamiliar with this process please refer to the Changing PC s IP Address on page 7 After changing your PC s IP address open your web browser and enter the address http 192 168 2 10 If your PC is properly configured you will see the login page of your Smart Switch If you do not see the login page please check your settings and repeat step 3 Enter the password the default is smcadmin and click on the Login button FEATURES AND BENEFITS 6 Click on the SYSTEM menu choice then click on LAN Settings when it appears On the LAN Settings page enter the IP address Subnet Mask and Gateway IP Address for the switch then click on the APPLY button No other configuration changes are required at this stage but it is recommended that you change the administrator s password before logging out To change the password click on the SYSTEM Password menu choice and fill in all the fields on the Password Settings page before clicking on the APPLY button see Setting the Switch s IP Address on page 16 for more information CONFIGURING THE SWITCH CONFIGURING THE SWITCH Using the Web Interface This switch provides an embedded HTTP web agent Usin
37. rate limiting parameters for each port 19 on the Switch CONFIGURING THE SWITCH Table 2 1 Switch Main Menu Continued Menu Description Page Broadcast Control Sets the broadcast storm control parameters 21 for every port on the Switch Port Mirroring Sets up the port mirroring features of the 22 switch to enable traffic monitoring TRUNKS 23 Membership Specifies ports to group into static trunks 24 Settings Configures trunk connection settings 24 Rate Limiting Sets the rate limiting parameters for each 25 Trunk configured on the Switch VLANS 26 VLAN Settings Configures the VLANs on the switch for both 26 Ports and Trunks QOS 29 Settings Sets the priority of packets within the switch 29 LOGOUT Quits to the Login page Web Configuration Displaying Status Overview You can easily identify the system by displaying the device name location and contact information Field Attributes System Information e System Name Name assigned to the switch system Number of Ports Number of built in ports Hardware Version Hardware version of the main board e Code Version Version number of the code Serial Number The serial number of the switch WEB CONFIGURATION Address Information Management VLAN ID of the configured VLAN this is set to 1 and cannot be changed all ports on the unit are members of VLAN 1 The management s
38. reate a maximum of eight trunks of up to eight ports each The Membership Table has one row for each port and ten columns Each row contains nine radio buttons which are used to indicate which trunk if any the port belongs to Field Attributes Port The front panel port number of the port Nota Trunk Member If the radio button in this column is selected the port is not a member of any trunks This is the default state Trunk T1 T8 These columns correspond to the eight trunks that are supported by the Switch Clicking on the radio button in any one of these columns causes the port to become a member of the corresponding trunk 25 CONFIGURING THE SWITCH Web Click TRUNKS Membership Click to select which Trunk member to which each port belongs Membership This page enables you to configure trunks on the Switch Membership Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk Trunk IN Ti 2 T3 T4 5 T6 T7 8 Member Le a a 9 a 4 gt 9 2 a a a 2 9 a a e elke o tene le te e te ie Te fe Lel el lo a e lei ei el O e lei e te NOM ie ie iel NO 01010901 9 0 0 090 9 9 9 9 9I0 9 0 0 OJOJOJO O JOJOJO O JOJOJOJOJOJO O OO Oo 0 001010 0 0 0100 0101 0 010101 0 0 0 0 9 0 5 0 0I9 0 0 0701010 el tel e ei e ie e 9797010 OO 0 0 0 OO NO RON O ON O MONO NNONNO 1 6 9 10 4 6 a apply canceL Figure 17 Trunk Membership Trunk Configuration Field
39. ry con nection point labelled Neutral connected directly to earth ground t Imp dance la terre Power Cord Set U S A and Canada The cord set must be UL approved and CSA certified The minimum specifications for the flexible cord are No 18 AWG not longer than 2 meters or 16 AWG Type SV or SJ 3 conductor The cord set must have a rated current capacity of at least 10 A The attachment plug must be an earth grounding type with NEMA 5 15P 15 A 125 V or NEMA 6 15P 15 A 250 V configuration Denmark The supply plug must comply with Section 107 2 D1 Standard DK2 1a or DK2 5a Switzerland The supply plug must comply with SEV ASE 1011 UK The supply plug must comply with BS1363 3 pin 13 A and be fit ted with a 5 A fuse which complies with BS1362 The mains cord must be lt HAR gt or lt BASEC gt marked and be of type HO3VVF3GO 75 minimum Europe The supply plug must comply with CEE7 7 SCHUKO The mains cord must be lt HAR gt or lt BASEC gt marked and be of type HO3VVF3GO 75 minimum IEC 320 receptacle Veuillez lire fond l information de la s curit suivante avant d installer le Switch AVERTISSEMENT L installation et la d pose de ce groupe doivent tre confi s un personnel qualifi e Ne branchez pas votre appareil sur une prise secteur alimentation lectrique lorsqu il n y a pas de connexion de mise la terre mi
40. se la masse COMPLIANCES e Vous devez raccorder ce groupe une sortie mise la terre mise la masse afin de respecter les normes internationales de s curit e Le coupleur d appareil le connecteur du groupe et non pas la prise murale doit respecter une configuration qui permet un branchement sur une entr e d appareil EN 60320 IEC 320 La prise secteur doit se trouver proximit de l appareil et son acc s doit tre facile Vous ne pouvez mettre l appareil hors circuit qu en d branchant son cordon lectrique au niveau de cette prise e L appareil fonctionne une tension extr mement basse de s curit qui est conforme la norme IEC 60950 Ces conditions ne sont maintenues que si quipement auquel il est raccord fonctionne dans les m mes conditions France et Peron uniquement Ce groupe ne peut pas tre aliment par un dispositif a imp dance 4 la terre Si vos alimenta tions sont du type imp dance 4 la terre ce groupe doit tre aliment par une tension de 230 V 2 P T par le biais d un transformateur d isolement rapport 1 1 avec un point secondaire de connexion portant l appellation Neutre et avec raccordement direct la terre masse Cordon lectrique Il doit tre agr dans le pays d utilisation Etats Unis et Can Le cordon doit avoir re u l homologation des UL et un certificat de ada la CSA Les spe cifications minimales pour la corde flexible
41. stered trademarks of their respective holders LIMITED WARRANTY Limited Warranty Statement SMC Networks Inc SMC warrants its products to be free from defects in workmanship and materials under normal use and service for the applicable warranty term All SMC products carry a standard 90 day limited warranty from the date of purchase from SMC or its Authorized Reseller SMC may at its own discretion repair or replace any product not operating as warranted with a similar or functionally equivalent product during the applicable warranty term SMC will endeavor to repair or replace any product returned under warranty within 30 days of receipt of the product The standard limited warranty can be upgraded to a Limited Lifetime warranty by registering new products within 30 days of purchase from SMC or its Authorized Reseller Registration can be accomplished via the enclosed product registration card or online via the SMC Web site Failure to register will not affect the standard limited warranty The Limited Lifetime warranty covers a product during the Life of that Product which is defined as the period of time during which the product is an Active SMC product A product is considered to be Active while it is listed on the current SMC price list As new technologies emerge older technologies become obsolete and SMC will at its discretion replace an older product in its product line with one that incorporates these newer tech
42. t likely to provide useful results DSCP Packets are prioritized using the DSCP Differentiated Services Code Point value The Differentiated Services Code Point DSCP is a six bit field that is contained within an IP TCP or UDP header Six bits allows the DSCP field to take any value in the range 0 63 inclusive When QoS Mode is set to DSCP the DSCP Configuration table appears which allows a priority normal or high to be set for each of the DSCP values You can use the Prioritize Traffic drop down list to quickly set the values in the DSCP Configuration table Select All Normal Priority to set all values to normal priority or select All High Priority to set all values to high priority Use Custom if you want to set each value individually WEB CONFIGURATION Web Click QOS Settings In QoS Mode select QoS Diabled 802 1p IP Port or DSCP to configure the related parameters QoS Settings Use Quality of Service QoS to set the priority of packets within the switch High priority packets will have precedence over normal priority packets so when the switch is congested fewer high priority packets will be dropped QoS Configuration QoS Mode Figure 21 QoS Settings 33 TROUBLESHOOTING TROUBLESHOOTING Diagnosing Switch Indicators 34 Symptom Power LED does not light after power on Probable Causes AC power cord may be defective Possible Solutions Check for loose connections Check the
43. tal number of frames received that were longer than 1518 octets excluding framing bits but including FCS octets and were otherwise well formed Jabbers The total number of frames received that were longer than 1518 octets excluding framing bits but including FCS octets and had either an FCS or alignment error 64 Bytes Frames The total number of frames including bad packets received and transmitted that were 64 octets in length excluding framing bits but including FCS octets 65 127 Byte Frames 128 255 Byte Frames 256 511 Byte Frames 512 1023 Byte Frames 1024 1518 Byte Frames 1519 1536 Byte Frames The total number of frames including bad packets received and transmitted where the number of octets fall within the specified range excluding framing bits but including FCS octets WEB CONFIGURATION Web Click STATUS Statistics Statistics This page displays the statistics for each port on your Switch Port Statistics 298989 u t D 2247 d ts 258 728742 1602 258 Figure 5 Port Statistics Displaying System Name You can easily identify the system by displaying the device name Field Attributes Switch Name Name assigned to the switch system 13 CONFIGURING THE SWITCH Web Click System Name This page allows you to set a meaningful name for your switch so that you can easily identify it when managing your network remotely Switch Name Sw SMC
44. tation must always be attached to a port on VLAN 1 IP Address Address of the VLAN to which the management station is attached Note that the management station must always be on VLAN 1 Valid IP addresses consist of four numbers 0 to 255 separated by periods e Subnet Mask This mask identifies the host address bits used for routing to specific subnets Default 255 255 255 0 e Gateway IP Address IP address of the gateway router between the stack and management stations that exist on other network segments Default 0 0 0 0 MAC Address The physical layer address Port Information e Type Indicates the port type e Link Status Indicates if the link is Up or Down e Speed Duplex Status Shows the current speed and duplex mode Displays a number the speed in Mbps followed by either fdx for full duplex or hdx for half duplex e Flow Control Status Indicates whether flow control is enabled or disabled e Autonegotiation Shows if auto negotiation is enabled or disabled Frame Type Either Tagged or All Tagged means that the port will only send and receive VLAN tagged packets When set to All the port will also send and receive untagged packets e PVID VLAN ID assigned to untagged frames received on the interface Default 1 Trunk Information Trunk The trunk label T1 through T8 are used as trunk labels e Type All trunks and ports on this switch are 10
45. tion which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help EC Conformance Declaration Class A SMC contact for these products in Europe is SMC Networks Eutope Edificio Conata II Calle Fructu s Gelabert 6 8 22 42 08970 Sant Joan Desp Barcelona Spain This information technology equipment complies with the requirements of the Council Directive 89 336 EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73 23 EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93 68 EEC For the evaluation of the compliance with these Directives the following standards were applied RFI Emission Limit class A according to EN 55022 1998 IEC 60601 1 2 EMC medical Limit class A for harmonic current emission according to EN 61000 3 2 1995 e Limitation of voltage fluctuation and flicker in low voltage supply system according to EN 61000 3 3 1995 Immunity Product family standard according to EN 55024 1998 111 COMPLIANCES iv e Electrostatic Discharge
46. zards Wear an anti static wrist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment Do not plug a phone jack connector in the RJ 45 port This may damage this device Les raccordeurs ne sont pas utilis pour le syst me t l phonique Use only twisted pair cables with RJ 45 connectors that conform to FCC standards Warnings in German Achtung Achtung Achtung Dieses Produkt enthalt keine Teile die eine Wartung vom Benutzer ben tigen Installation und Deinstallation des Ger tes m ssen von qualifiziertem Servicepersonal durchgef hrt werden Wenn das Ger t an eine Steckdose angeschlossen wird mu der MasseanschluB am dreipoligen Netzstecker mit Schutzerde verbunden werden um elektrische Gefahren zu vermeiden ix COMPLIANCES Environmental Statement The manufacturer of this product endeavours to sustain an environmentally friendly policy throughout the entire production process This is achieved though the following means e Adherence to national legislation and regulations on environmental production standards Conservation of operational resources e Waste reduction and safe disposal of all harmful un recyclable by products e Recycling of all reusable waste content e Design of products to maximize recyclables at the end of the product s life span e Continual monitoring of safety standards End of Product Life Span This product is manufa
Download Pdf Manuals
Related Search