SmartLabs 2484D User's Manual
Contents
1. Quick Start Guide o KeypadLinc INSTEON 8 Button Countdown Timer ao Model 2484D A Countdown Timer that Turns Itself Plus other INSTEON Devices off Automatically a le Introduction Countdown Timer KeypadLinc INSTEON Countdown Timer is a general purpose countdown timer with 7 or 8 timer durations Like other countdown timers it will turn the connected lights circuit off when its timer expires However that s where the similarity ends Countdown Timer can also turn other INSTEON devices off when its timer expires Still further when you Link other INSTEON devices as a Controller to Countdown Timer it will automatically start its countdown timer for the amount of time you choose Installation Important Installation should be performed only by a qualified electrician or by a homeowner who is familiar and comfortable with electrical circuitry If there are any questions consult an electrician For setup questions contact Tech Support at SmartLabs for guidance Tools required Phillips screwdriver slotted screwdriver and a wire cutter stripper Two or more properly installed INSTEON Access Points are strongly recommended for every home to ensure reliable communication You will need to ID all your wires before beginning For a wiring diagrams including 3 way circuits see the KeypadLinc Dimmer Owner s Manual at http www smarthome com 2486D pdf Disconnect power at the service panel Remove trim plate and existing switch2. dimmer Connect Countdown Timer s copper wire to ground with a wire nut or screw as appropriate Connect Countdown Timer s white wire to neutral with a wire nut Connect Countdown Timer s black wire to hot wire with a wire nut Connect Countdown Timer s red wire to the switch leg with a wire nut control of a local load is optional Carefully screw Countdown Timer into electrical box and replace trim plate Restore power at the service panel Countdown Timer will return to its last on off state Test Countdown Timer by pressing the 2 min button Your lights will turn on flash after 1 minute and turn off after 2 minutes So ae Operation Tap the 5 min button this will turn your lights on for 5 minutes Your lights will turn on and any INSTEON devices controlled by your Countdown Timer will also turn on 5 min LED will turn on After 3 minutes the 2 min LED will turn on and the 5 min LED will turn off After 1 minute the 1 minute warning will turn your lights off then back on indicating 1 minute left After 1 more minute your lights will turn off and any INSTEON devices linked to Countdown Timer will also be turned off To turn lights off at any time tap the OFF button or the button whose LED is on Your lights will turn off and any INSTEON devices linked to Countdown Timer will also be turned off Creating Links to Control other INSTEON Devices from Countdown Timer Press amp hold any button on Countdown Timer unt
3. he button until your lights flash LED on your Controller will stop blinking 3 Test by turning your lights on and off from your Controller When turned on from your Controller your lights will remain on for the time indicated on the button selected during step 2 Enabling Disabling Features 1 Minute Warning By factory default Countdown Timer will flash your lights 1 minute before the countdown timer expires e To disable if enabled 1 Minute Warning tap the 5 min button then press amp hold the SET button for 5 seconds three times e To enable if disabled 1 Minute Warning tap the 2 min button then press amp hold the SET button for 5 seconds three times Dimming By factory default Countdown Timer will act as a dimmer allowing you to dim the lights connected to it either locally or remotely via INSTEON e To disable local Dimming if enabled tap the 15 min button then press amp hold the SET button for 5 seconds three times e To enable local Dimming if disabled tap the 10 min button then press amp hold the SET button for 5 seconds three times Factory Reset 1 Pull SET button out and wait 15 seconds 2 Push SET button in and hold in for 5 seconds Your lights will turn on after 3 seconds all programmed links will be removed and features returned to the factory defaults Power Restore 1 After a power outage pull the SET button out and wait 15 seconds then push SET button back in Changing 8 OFF Butt
4. il its LED begins blinking Press amp hold the SET button on the INSTEON compatible Responder you wish to control until its LED flashes Note for multi button devices press amp hold the button of choice until LED load flashes Note All the devices you link in this manner will be turned on when you turn Countdown Timer on and will turn Off when the timer expires Removing Links to other INSTEON Devices from Countdown Timer Press amp hold the corresponding button on Countdown Timer until its LED begins blinking Press amp hold the same button again hold it for 15 seconds Press amp hold the SET button on the INSTEON compatible Responder you wish to remove from Countdown Timer until its LED flashes Note for multi button devices press amp hold the button of choice until LED load flashes page smartiads Quick Start Guide KeypadLinc INSTEON Countdown Timer 8 Button Creating Links to Control Countdown Timer from other INSTEON Devices 1 Identify your Controller type from the list below If your Controller is not shown consult its Owner s Manual Press amp hold the desired button until its LED begins blinking Press amp hold the ON button of the desired button pair until it beeps Press amp hold the SET button until LED blinks 2 Press amp hold the button that represents the amount of time you would like you lights to remain on when turned on by the INSTEON Controller selected during step 1 above hold t
5. on Behavior This feature allows you to change the behavior of the 8 button on Countdown Timer default OFF Note ON OFF and 4 hr key caps included e To turn 8 button into an ON OFF toggle button tap the 1 hr button press amp hold the SET button for 5 seconds three times LED will stop blinking To turn OFF button into a 4 hour timer button a Tap the 30 min button release then press amp hold the SET button for 5 seconds three times LED will stop blinking b Tap the 8 bottom right button then press amp hold the SET button for 5 seconds three times LED will stop blinking To turn OFF button back into an off only button a Tap the 30 min button release then press amp hold the SET button for 5 seconds three times LED will stop blinking b Tap the 2 hr button release then press amp hold the SET button for 5 seconds three times LED will stop blinking Note Once you have programmed the 8 button simply pop the OFF key cap off and replace with appropriate button key cap For HELP call our friendly tech support 866 243 8018 SmartLabs Limited Warranty SmartLabs warrants to the original consumer of this product that for a period of two years from the date of purchase this product will be free from defects in material and workmanship and will perform in substantial conformity to the description of the product in the owner s manual This warranty shall not apply to defects or errors caused by misuse or neglec
6. t Copyright 2007 SmartLabs 16542 Millikan Ave Irvine CA 92606 5027 866 243 8018 www smartlabsinc com page zotz smartiads
Download Pdf Manuals
Related Search