Smarthome 7307 User's Manual
Contents
1. 4 Close the battery cover and re insert the two screws 282. If hanging the unit insert two screws using the template provided If screwing the back directly to the wall take the back plate right off by prying apart one hinge Use as much force as needed The plastic hinge will not break 5 Using the template attach the backplate on to the wall with 4 screws 6 Mount the Control Panel on the backplate Insert one hinge into the hole then twist the other hinge into position 7 Firmly close the case 8 Plug the AC adapter into a power outlet The red AC PWR light and keypad back light will be on INSTALLING THE DOOR WINDOW SENSOR WT 433 It is recommended to install one sensor on your front door and the other on your back door Each contact sensor has 4 parts Transmitter Magnetic Switch Magnet Spacers 1 Position the transmitter be side the door window frame on the wall using either two sided tape or screws If you are using screws first pry off the back plate with a small screwdriver and screw the back plate into posi tion using the template Then click the transmitter on to the back plate now mounted on the wall INSTALLATION 2 Position the magnetic switch connected to the transmitter on the door window frame 3 Position the magnet on the door beside the magnetic switch They should be no more than 1 cm 3 8 inch apart When the door window is closed the magnets are in contact When the door window is opened contact is broken and the tr
3. DISARM THE SYSTEM USING THE KEYPAD ON THE CON TROL PANEL 1 Press the current MPIN 000 2 Press All the lights but the AC PWR light go off The system is now disarmed Note If MPIN is entered when the system in not activated the system will default back to the last sequence before the unit was turned off Emergency Silent Alarm works in conjunction with the Emergency Dialer option see Additional Accessories If under duress when disarming the system 1 Enter the current MPIN 000 2 Press B B This will terminate the delay mode stop the steady repeated beep and return to the previous arm mode It will also send a signal to the Emergency Dialer silently which will then automatically send a prerecorded message for help 14 KEYCHAIN TRANSMITTER 4B 434 The Keychain Transmitter conveniently fits on any keychain It allows you to arm and disarm the system from a distance of approximately 100 feet from the Control Panel The distance will depend on what is between the key chain transmitter and the Control Panel It also has a panic button that lets you remotely activate the siren instantly Note Make sure you press down on the transmitter for one full second or the system may not respond TO ARM SYSTEM USING THE KEYCHAIN TRANSMITTER There are 2 different arm options to choose from 1 Press button 1 and the Control Panel will beep once The system will be armed in the Away Seguence To be used
4. especially caused by changes in temperature may trigger the Motion Sensor and cause false Insert jumper to alarms Please carefully test your Motion ee Sensor to make it will only be triggered by DIAGRAM 2 people Installation is now completed and now test your system to ensure all the sensors are communicating with the Control Panel See the next section TESTING YOUR SYSTEM 10 TESTING YOUR SYSTEM Before you learn how to use your security system test to make sure that the door window sensors and the motion sensor are communicating with the Control Panel Set the Control Panel to CHIME MODE which will emit a subtly two tone chime when any of the sensors are activated To set control panel to CHIME MODE 1 Enter your MPIN 0 0 0 on the Control Panel MPIN is factory set at 0 O 0 To change MPIN see MASTER PERSONAL IDENTIFICATION NUMBER MPIN on page 17 2 Press A a O O 0 CHIME O O O 1 2 DELAY ACPWRLOBATARMW O OJ O O INSTANT 3 Press ff The red arm light and all 4 green lights above the numbers and beside the word chime will go on The system will now emit a chime sound when any sensor is activated The lights and sounds of the Control Panel are explained in the next section see Lights and Sounds The door window sensors are factory set to communicate with zone 1 and the motion sensor to communicate with zone 2 If you would like to have the sensors communicate with a differe
5. included wall anchors and templates to help position the screws correctly How to use the templates 1 Cut the template required 2 Tape it in position 3 Screw part way into the surface where the holes are marked 4 Unscrew the screws and remove the template 5 Screw the component in place where you started the screws INSTALLING THE CONTROL PANEL SC 001 Position the Control Panel near the door you use to enter exit from most often and within access of an electrical outlet The Control Panel runs on regular electrical current It also contains a 9 volt backup alkaline battery in case power is interrupted for any reason There are 3 ways to attach the Control Panel on the wall 1 Use double sided tape for temporary use 2 Hanging it from the two keyholes on the two stationary screws 3 Screwing the back onto the wall with 4 screws To mount the Control Panel 1 Open the case a Press the two tabs on top of the Control Panel b Pull open the front 2 Thread the AC adapter cord through the large hole in the back of the unit and plug it into the circuit board as shown The Adapter cord must be inserted through the back of the unit before it is attached to the wall 3 Insert the 9 volt alkaline battery and rotate the antenna from the inside of the Control Panel to the outside y FE SMARTHOME COM 1 800 SMART HOME 949 221 9200 http www smarthome com Order 7307 INSTALLATION 4 Attach the unit to the wall
6. 0 SMART HOME 949 221 9200 http www smarthome com Order 7307 BATTERY MAINTENANCE The SC 100 Security System comes with 5 batteries that at some point you may have to replace 9 volt alkaline battery for the Control Panel 9 volt alkaline battery for the Motion Sensor 12 volt alkaline batteries for the 2 Door Window Sensors 12 volt alkaline battery for the Keychain Transmitter Recommendation Test you system periodically to ensure that all batteries are working CONTROL PANEL BATTERY The Control Panel comes equipped with a backup battery in case the electrical power is interrupted for any reason When the Control Panel battery is low the LOBATT light goes on Also when the LOBATT light is on and if you press any key on the keypad 10 beeps warn you that the battery needs to be changed To replace the Control Panel backup battery 1 Disarm the unit 2 Open the Control Panel case by pressing down on the two tabs on the top edge and pull the front forward 3 Disconnect the old battery 4 Connect the new battery 5 Close the Control Panel Note To guard against sabotage the Control Panel is equipped with an emer gency switch that activates the alarm instantly when the case is opened Make sure that the unit is disarmed when you open the case or you will activate the alarm The battery life 9 volt alkaline battery is approximately two years if used only for backup Note If the A
7. C adapter is disconnected while the battery is replaced the security system will erase all the modifications that have been made and return to the factory default Also your MPIN will return to 000 26 BATTERY MAINTENANCE MOTION SENSOR BATTERY The Motion Sensor operates on a 9 volt alkaline baitery accessible beneath a sliding panel on the bottom of the unit All remote sensors come with the battery already installed Disarm the Control Panel before replacing all baiteries When the battery level is low the Motion Sensor will emit a long beep approx 3 seconds when motion is detected This indicates you should replace the 9V battery To replace the Motion Sensor battery 1 Take the Motion Sensor down from the wall 2 Slide off the battery cover 2 3 Take the old battery out of the battery compartment 4 Disconnect the old battery from the connector wire 5 Connect the new battery to the connector wire 6 Put the new battery into the battery compartment 7 Slide the battery compartment back on 8 Set the switch on the side of the Motion Sensor to ON 9 Put the unit back on the wall Switch unit to the off position when not in use for long periods of time to extend battery life AC Adapter Optional An optional AC adapter can be plugged in to the Motion Sensor as a regular power source The output voltage of this optional AC adapter should be at 9V under nor mal operating condition the Motion Senso
8. CATION NUMBER SPIN You may want to give someone limited access to the system baby sitter cleaner repairman etc For this purpose the SC 100 provides you with the option of adding up to 3 separate SPIN A SPIN can be any number of 3 digits or more You can use a SPIN to arm and disarm the system but not to program it programming is explained in the next section When someone no longer needs to have access to your security system you can simply delete their SPIN Adding a SPIN Enter the current MPIN Press Press the number key to identify user either 1 2 or 3 Press ao pen Enter the new SPIN your SPIN must be a minimum of digits 6 Press If the system accepts the new SPIN you will hear a long beep If you hear three short beeps the system did not accept the new SPIN Start again Deleting a SPIN Enter the current MPIN Press Press the number to identify the user either 1 2 or 3 Pe 269 y Press 5 Press one final time If the SPIN was successfully deleted you will hear a long beep 18 ADVANCED PROGRAMMING PROGRAM SENSORS TO DIFFERENT ZONES You now have a basic understanding of how the SC 100 security system works In this section Advanced Programming we will explain how to move sensors to different zones how to change the alarm modes for example from Instant Mode to Delay Mode and how to customize the pre programme
9. RAMMING Program Sensors to Different 20 19 To Clear 20 20 To program a sensor tO a 20 20 To delete a Keychain Transmitter from Zone 5 21 To program a Keychain Transmitter or keypad transmitter option LO ZOMG 5 SET 21 Standard Arming 22 Additional Arming 22 Customize a 24 SUMMARY OF ARMING 25 BATTERY MAINTENANCE Contool PANG 26 Motion SONSOM ADRAN CSS oT 27 Door Window 27 Keychain 28 ADDITIONAL ACCESSORIES 29 O 3 SMARTHOME COM 1 800 SMART HOME 949 221 9200 http www smarthome com Order 7307 PACKAGE CONTENTS Everything reguired for installation is included with this package 1 Control Panel SC 001 includes 1 antenna installed 1 AC adapter 1 9 volt alkaline bat
10. RANSMITTER OR KEYPAD TRANS MITTER OPTION TO ZONE 5 1 Enter the current MPIN 2 Press 3 Press 5 4 Press 5 Within 30 seconds of pressing the press any of the four buttons on the Keychain Transmitter OR press the panic button on the Keypad Transmitter You will hear a long beep and the Keychain Transmitter will now communicate with zone 5 NOTE Zone 5 is designated for keychain and keypad transmitter ONLY Please do not program any sensors other than keychain and keypad trans mitters into zone 5 otherwise the system will not work properly SMARTHOME COM 1 800 SMART HOME 949 221 9200 http www smarthome com Order 7307 ADVANCED PROGRAMMING STANDARD ARMING SEQUENCES Each zone can be programmed to react 5 different ways when it receives a signal from a remote sensor 1 Chime Mode represented by the green lights When only the green light is on and the Control Panel receives a signal from a remote sensor the Control Panel emits a subtly two tone chime 2 Instant Mode represented by the red lights When only the red light is on and the Control Panel receives a signal from the remote sensor the Control Panel will activate the siren instantly 3 Delay Entry Mode represented by the green and red lights When both the green and red lights are on and the Control Panel re ceives a signal from a remote sensor the lights will flash and the Control Panel will beep for 30 seconds befo
11. SMARTHOME COM 1 800 SMART HOME 949 221 9200 http www smarthome com Order 7307 Total Protection Alarm System SMARTHOME 7307 PREMISES PROTECTED BY ELECTRONIC SECURITY SYSTEM PAT D410633 Patents Pending SMARTHOME COM 1 800 SMART HOME 949 221 9200 http www smarthome com Order 7307 TABLE OF CONTENTS Your Guide to the Total Protecti Al Syst PACKAGE CONTENTS aaa a YN YNN yne Ao 4 ys OVERVIEW 5 SMARTHOME 7307 PLANNING YOUR HOME SECURITY 5 6 INSTALLATION CONO EFE E FYNN FN NF 7 Door Window 8 MOON SETISOT eisiaa RR EAEE SES 9 TESTING YOUR 11 LIGHIES AND SOUNDS irris aaia 12 STANDARD PROGRAMMING Arming and disarming the Security System using the Keypad 13 Arming and disarming the Security System using the Keychain TRAMSIMUNMG iiai 15 Panic Button on the Keychain 16 PASSWORDS Master Personal Identification Number 17 Secondary Personal Identification Number 18 ADVANCED PROG
12. T HOME 949 221 9200 http www smarthome com Order 7307 STANDARD PROGRAMMING Option 2 Home Seguence To arm your system when someone remains in the premises 1 Press the current MPIN 000 2 Press C You hear a long beep The arm light and the red lights in zones 3 and 4 go on Both the green and red lights flash in zone 1 for 45 seconds which gives you 45 seconds to leave the premises before the system is activated After 45 seconds both the green and red lights in zone 1 remain on Upon re entering the premises through zone 1 you have 30 seconds till the alarm sounds The system gives you 30 seconds from the time you activate the door window sensor for example opening the front door to get to the Control Panel to deactivate the system Zone 2 remains off which allows ihe person in the premises to move around without activating the motion sensor Zones 3 and 4 remain instant If any sensor in zone 3 or 4 are activated the alarm sounds instantly Option 3 Night Seguence To arm your system when there are people in the premises and no one is expected to enter or exit Example at night when everyone is sleeping 1 Press the current MPIN 0 00 2 Press A 3 Press B You hear a long beep The arm light the red light in zones 1 3 amp 4 go on If any of the sensors are activated in any of these 3 zones the alarm is sounded instantly Zone 2 the motion sensor remains off allowing movementthroughoutthe premises TO
13. and the motion sensor once everything is installed explains how to test each device 2 Lights and Sounds page 12 explains the function of all the lights on the Control Panel describes all the sounds emitted from the Control Panel 3 Standard Programming and Passwords pages 13 18 how to arm and disarm the system using the Control Panel how to use the 4 button keychain transmitter to arm and disarm the Control Panel how to personalize your MPIN Master Personal Identification Number how to program a SPIN Secondary Personal Identification Number 4 Advanced Programming pages 19 24 the Control Panel receives signals from the remote sensors in four different zones Explains how to program different remote sensors to different zones the Control Panel is programmed with different alarm modes for different situations Explains how to program these alarm modes explains the different alarm sequences preprogrammed at the factory for your convenience 5 Summary Table page 25 summarizes all preprogrammed alarm sequences 6 Maintenance page 26 28 explains how to change batteries in all remote sensors and the Control Panel 5 SMARTHOME COM 1 800 SMART HOME 949 221 9200 http www smarthome com Order 7307 PLANNING YOUR HOME SECURITY NEEDS Before you begin to install your security system analyze the premises to determine your security needs Consider those doors and windows which are
14. ansmitter sends a signal to the Control Panel to activate the chime or alarm INSTALLING THE MOTION SENSOR PS 433 The motion sensor senses motion from up to 13 meters 40 feet away ina 110 degree arc DETECTING AREA Unit meter It works best when installed from 2 meters aa approx 7 feet off the ground in a corner a Please position the sensor so that itis down at an angle of about 12 degrees We recommend that you position the motion Tm sensor where it will guard the bedrooms For example have your motion sensor monitoring NS the stairway which leads to all the bedrooms upstairs A hallway or central area can also be ee AUR used 1 Once you have decided on a location tape the template into position If you are putting the motion sensor in a corner first fold the _ template along the center line so it will fit snugly into the angle Screw the two mount ing screws in position if installing on a flat wall use the screw holes one above the other if installing in a corner use the screw holes on sides of the unit 2 Insert the 9 volt alkaline battery original battery inserted by factory 3 Match up the two screws with the appropriate two keyholes on the back of the Motion Sensor then hang the unit in position 9 SMARTHOME COM 1 800 SMART HOME 949 221 9200 http www smarthome com Order 7307 INSTALLATION Cont Installi
15. d arm seguences for example if you only use one door to enter exit from your secondary door should communicate with a zone that is in instant mode Your SC 100 Security System is divided into five zones The 1stfour zones are displayed on the Control Panel as 4 pairs of lights one green and the other red When a remote sensor door window sensor or motion sensor is activated it sends a signal to one of the 1st four zones on the Control Panel Each zone can communicate with as many as six sensors The Control Panel can communicate with a maximum of 24 different sensors The fifth zone which is not represented by any lights on the Control Panel is programmed to communicate with Keychain Transmitters Zone 5 can accommodate a maximum of six Keychain Transmitters 4B434 or Keypad transmitters KP 433 option You can assign your remote sensors to whatever zones you want For your convenience we have preprogrammed the remote sensors for you Both door window sensors are assigned to zone 1 and the motion sensor is assigned to zone 2 You may wish to program a sensor to communicate to a different zone For example if you do not enter exit from your back door you may want to change the zone so that the door sensor is communicating with a different zone Currently this sensor is communicating with zone 1 but if you change it so it will be communicating with zone 3 the alarm will now sound instantly You may have a premises with three ente
16. e Home Seguence and Night Seguence make up the six preprogrammed arm seguences However if any of these six seguences do not satisfy your needs you may want to change the modes in certain zones For example your zone 2 motion sensor is currently in delay mode If your motion sensor is located in the base ment and you would like to change it to the instant mode see below 23 SMARTHOME COM 1 800 SMART HOME 949 221 9200 http www smarthome com Order 7307 ADVANCED PROGRAMMING TO CUSTOMIZE A SEGUENCE Program the system to the sequence you want to alter 1 Enter the current MPIN 2 Press B 3 Press a number key to select the zone you would like to change 1 2 30r 4 The zone lights in the chosen zone will flash for eight seconds 4 While the lights flash press A 5 Select the new mode you want to use 0 Disarm 1 Chime Mode 2 Delay Entry Exit Mode 3 Instant Mode 6 Press A long beep signals a successful change SUMMARY OF ARMING SEGUENCES Below is a table summarizing all the preprogrammed sequences Sequence Zone 1 Zone2 Zones3 amp 4 When sequence should be used FOR TESTING MPINA chime chime chime use for testing after installation and to test batteries also use as a subtle chime when a remote sensor has been activated BASIC PROGRAMMING MPINBC exitdelay off instant use when leaving the premises after 45 sec entry delay entry delay instant and no one i
17. g and the remote sensor will now communicate to that zone Note You can only add remote devices to a zone one by one but you can not remove them one by one You must clear all sensors from the zone and add back the ones you want TO PROGRAM THE MOTION SENSOR TO THE SECURITY CONTROL PANEL SC 001 1 Set the switch on the side of the Motion Sensor to ON Wait 60 seconds to warm up 2 Enter the current MPIN Master Personal Identification Number 20 ADVANCED PROGRAMMING 3 Press B 4 Press the number key to identify which zone to add the Motion Sensor to 1 2 3 4 We recommend you program the motion sensor to zone 2 The zone light will flash for eight seconds 5 While the zone light is flashing press 6 While the zone light is flashing walk in front of the Motion Sensor in order to activate it You will hear a long beep if the motion sensor is learned to the control panel The zone light will stop flashing and the remote sensor will now communicate to that zone TO DELETE A KEYCHAIN TRANSMITTER FROM ZONE 5 1 Enter the current MPIN 2 Press 3 Press 5 4 Press 5 Do not activate any Keychain Transmitters or sensors for 30 seconds after the was pressed You have now cleared zone 5 from communicating with all Keychain Transmitters Please re program the keychain transmitters that you would like to use by the following instruction TO PROGRAM A KEYCHAIN T
18. is the red button on the keypad 16 PASSWORDS MASTER PERSONAL IDENTIFICATION NUMBER MPIN Security access to the SC 100 is controlled by a MASTER PERSONAL IDENTIFICATION NUMBER MPIN or SECONDARY PERSONAL IDENTIFICATION NUMBER SPIN All programming sequences start with either the MPIN or SPIN To Change your MPIN 1 Enter the current MPIN the MPIN is factory preprogrammed with 000 Press Press 0 Press PS O 5 Enter your new MPIN your MPIN must be a minimum of 3 digits 6 Press If the system accepts the new MPIN you will hear a long beep If you hear three short beeps the system did not accept the new MPIN Start again from the beginning Note If you enter an incorrect MPIN or SPIN the alarm will sound after the forth incorrect attempted Note If you forget the current MPIN unplug the Control Panel and remove the battery The MPIN will automatically return to the factory default of 0 0 0 Make sure the unit is disarmed when you open the Control Panel The Con trol Panel has a built in Defence System When the unit is armed and the Control Panel is opened or vandalized the alarm will sound and send a signal to the emergency dialer if applicable For more information on the Emer gency Dialer see Additional Accessories page 29 17 SMARTHOME COM 1 800 SMART HOME 949 221 9200 http www smarthome com Order 7307 PASSWORDS SECONDARY PERSONAL IDENTIFI
19. isarm the system before the alarm sounds Two tone beep System is set on exit delay you have 45 seconds to leave the premises once the system has been activated After the 45 seconds the system emits a two tone beep and the system is now armed If you make a mistake while programming the Control Panel emits three short beeps That means the system has cleared and you must start the pro gramming sequence from the beginning If you get lost in the programming sequence or have made a mistake and want to start over again press the on the key pad of the Control Panel until you hear three short beeps This will clear the system then you can start again from the beginning If no button is pressed for eight seconds while in the middle of a programming sequence the system will also clear itself 12 STANDARD PROGRAMMING Now that the system is installed and the sensors are communicating with the Control Panel it is time to learn how to do basic programming of your security system More advanced features are explained further in the manual see Advanced Programming You can arm and disarm the system by using either the keypad on the Control Panel or the 4 button keychain transmitter or Keypad transmitter option TO ARM THE SYSTEM USING THE KEYPAD ON THE CONTROL PANEL All programming sequences begin with the Master Personal Identification Number MPIN There is only one MPIN which has been factory set at 0 0 0 You can also a
20. more likely to be used as points of entry by an intruder the ones that are poorly lit or the entrances that can not be seen from the street Sketch a map of the premises and determine which doors and or windows need contact sensors and which areas of the premises need to be monitored by a motion sensor We recommend that you put one door window sensor on the door you enter exit from most often the other sensor on your secondary entrance and your motion sensor monitoring the bedrooms stairway or hallway leading to the bedrooms If you have determined that you need additional sensors see Additional Accessories on page 29 Below is an example of how to position your security system in a house BACKDOOR BEDROOM DOOR WINDOW SENSOR BEDROOM MOTION SENSOR gwe LIVING ROOM DINING ROOM CONTROL PANEL DOOR WINDOW FRONT ff SENSOR DOOR You may choose to install a motion sensor to protect any valuables such as antigues or paintings Point the motion sensor directly atthe valuables and if they are disturbed in any way the alarm will be sounded INSTALLATION The Control Panel door window sensors and the motion sensor are installed using the screws included We have also included double sided tape for the door window sensor and the motion sensor to use for temporary installation while you are positioning the sensors Once all the sensors are positioned correctly install them permanently with the screws We have also
21. ng the motion sensor PS 433 Set the switch on the side to TEST and allow 60 seconds for the unit to warm up when using test mode a signal will not be sent to the Control Panel Now walk in the area you want the motion sensor to detect movement in If movement is detected the red light on the front of the unit will appear If the red light does not appear movement has not been detected and you should reposition your motion sensor PULSE COUNT FEATURE Your Motion Sensor is eguipped with Pulse Count feature This new feature significantly reduces false alarms Now when Pulse Count is enabled 2 consecutive movements are required in order to trigger the motion SS sensor However the response time of the ey motion sensor will become slower Therefore you have the option to either enable or dis able this feature to suit your specific needs The factory default for this feature is set to ON Your can disable this feature by relocat ing the Pulse Count jumper which is the red jumper located inside the battery compart ment When the red jumper is on the left 2 posts Diagram 1 Pulse Count feature is enabled If you would like to disable Pulse Count please remove the red jumper and insert it on the right 2 posts Diagram 2 Note When installing the Motion Sensor avoid placing it near heat or cold producing devices i e A C or furnace vents fans ovens space heaters etc Air movement
22. nt zone see PROGRAM SENSORS TO DIFFERENT ZONES on page 19 To test the Door Window Sensor Open the door window and break the contact between the magnetic switch and the magnet A signal will then be sent to the Control Panel which will chime telling you that the signal has been received One of the four green lights on the Control Panel will flash once as the chime sounds If you open the front door the green light above the 1 zone 1 will flash To test the Motion Sensor Slide the button on the side of the motion sensor to ON and allow 60 seconds for the unit to warm up then walk in the monitored area in front of the motion sensor Once movement is detected a signal will be sent to the Control Panel The Control Panel will then emit a two tone chime and the green light above the 2 zone 2 will flash once The motion sensor has been programmed to send its signal to zone 2 in the Control Panel It will take about 30 seconds for the motion sensor to reset itself before it can send another signal If you have pets have them walk in the monitored area to see if they activate the motion sensor If so turn the motion sensor off if these pets have access to the monitored area Smaller pets will not be picked up by the motion sensor 11 SMARTHOME COM 1 800 SMART HOME 949 221 9200 http www smarthome com Order 7307 LIGHTS AND SOUNDS Below is an explanation of the lights and sounds of the Control Panel LIGHTS ACPWR light
23. oes not have the exit delay so you are not able to leave the premises without activating the alarm Zone 2 the motion sensor is off allowing movement the premises and zones 3 amp 4 are instant Option 2 Advanced Home 2 use to secure the premises while staying in the building Delays the alarm to allow someone to enter the building and or walk in the monitored area of the motion sensor to deactivate the alarm 1 Enter the current MPIN 2 Press A 3 Press C You will hear a long beep The arm light the red and green lights in zones 1 and 2 as well as the red lights in zones 3 and 4 go on Zone 1 amp 2 has the entry delay to allow someone to enter through the front door and walkin the area monitored by the motion sensor and deactivate the system before the siren sounds This option does not have the exit delay so you are not able to leave the premises without activating the system Zones 3 amp 4 are instant Option 3 Chime Seguence this seguence is used for testing the system but it can also be used to subtly alert you when a zone has been activated Example if a young child opens the front door the Control Panel will emit a two tone chime advising you that the front door has been opened See page 11 for programming information for the CHIME SEOUENCE The three arm seguences above Advanced Home 1 Advanced Home 2 and Chime Seguence along with the three seguences described in the STANDARD PROGRAMMING Away Seguenc
24. on System is being powered by electrical current ACPWR light off System is not receiving any electrical power LOBATT light off Backup battery is connected and working LOBATT light flashing Backup battery is weak needs to be replaced ARM light off System is disarmed ARM light on System is armed Key Pad Back Light If powered by AC adapter back light is always on If powered by back up battery only stays on for eight seconds when any button is pressed Green lights above 1 4 System will emit a two tone chime when a sensor is activated CHIME MODE Red lights below 1 4 System will sound alarm instantly when a sensor is activated INSTANT MODE Both green and red lights System will beep steadily for 30 seconds when 1 4 a sensor is activated after the 30 seconds the alarm willsound DELAY ENTRY MODE Both green and lights Lights will flash for 45 seconds All remote sensors pro flashing grammed to that zone will not communicate with the Control Panel for those 45 seconds which gives you time to exit the premises before the system is armed SOUNDS Three short beeps You have made a mistake start again Long beep You have successfully completed a command Short beep You have pressed a key in the right order Two tone chime A device has been activated in CHIME MODE Siren 3 minutes A device has been activated in INSTANT MODE Steady repeatedbeep alarm has been triggered in DELAY MODE You have 30 seconds to d
25. r exit doors You will need additional door window sensors see Additional Accessories 19 SMARTHOME COM 1 800 SMART HOME 949 221 9200 http www smarthome com Order 7307 ADVANCED PROGRAMMING To program sensors to send their signals to a different zone you must first clear them from communicating with their current zone TO CLEAR A ZONE 1 Enter the current MPIN 2 Press B 3 Press the number key to identify current zone 1 2 3 or 4 The zone light s will flash for eight seconds 4 While the zone light s are flashing press Now both the green and red lights flash for 30 seconds 5 Do not activate any sensors while these lights are flashing Once the lights stop flashing the zone is cleared of all devices Now that you have cleared the zone from communicating with all sensors program the sensors to the zones you would like them to communicate with see below TO PROGRAM A SENSOR TO A ZONE 1 Enter the current MPIN 2 Press B 3 Press the number key to identify which zone to add the sensor to zone 1 2 30 4 The zone light s will flash for eight seconds 4 While the zone light s are flashing press Now both the green and red lights flash for 30 seconds 5 While the zone lights are flashing go to the remote sensor you are adding and activate it Walk in front of the motion sensor or open the door window You will hear a long beep the zone light will stop flashin
26. r will not consume the power of the 9V battery However we recommend users should still install the 9V TW TT battery as a back up power supply in case of a power failure i DOOR WINDOW SENSOR BATTERY Each door window sensor operates on a 12 volt alkaline bat tery that is inside the transmitter The sensors come with the batteries already installed Lie To replace the battery 1 Push on the clip at the bottom of the transmitter case with a sharp object such as a paper clip or pen knife and pull it away from the backplate 2 Pry out the old battery from one end 3 Push the new battery back into place A diagram be side the battery well indicates which end is positive and which is negative 4 Snap the transmitter back onto the backplate 27 SMARTHOME COM 1 800 SMART HOME 949 221 9200 http www smarthome com Order 7307 BATTERY MAINTENANCE KEYCHAIN TRANSMITTER BATTERY The Keychain Transmitter operates on a 12 volt alkaline battery which is installed at the factory There are two screws on the back of the transmitter that holds the case together To replace the Keychain Transmitter battery 1 Undo the two screws on the back of the transmitter The back will then come off 2 Using a small screwdriver or pen knife pry out the old battery from one end 3 Place the new battery in position A diagram beside the battery well indicates which end is positive and which is negative
27. re the alarm sounds These 30 seconds give you time to enter the premises and deactivate the alarm before the siren sounds 4 Delay Exit Mode represented by the flashing of both the green and red lights for 45 seconds When both green and red lights are flashing the control panel will not recognize any remote sensors communicating to that zone These 45 seconds allow you time to exit the premises before that zone is activated When the lights stop flashing both green and red lights will remain on which is now in DELAY ENTRY MODE See above for information on DELAY ENTRY 5 Off neither the green nor the red lights are on The Control Panel will not recognize any signals from a remote sensor We have preprogrammed different combinations of the above modes to meet different situations see S TANDARD PROGRAMMING ADDITIONAL ARMING SEQUENCES Below are three additional programming options you may want to use Option 1 Advanced Home 1 use to secure the premises while staying in the building Delays the alarm to allow someone to enter the building and deactivate the alarm 22 ADVANCED PROGRAMMING 1 Enter the current MPIN 2 Press A 3 Press A You will hear a long beep The arm light the red and green lights in zones 1 and the red lights in zones 3 and 4 go on Zone 1 has the entry delay to allow someone to enter through the front door and deactivate the system before the siren sounds This option d
28. s inside MPIN exitdelay off instant use when leaving the premises after 45 sec and someone is inside the premises instant off instant use when people are in the premises and no one is expected to enter exit off off off turns off the system note when MPIN is enter and the system is already off the system will default back to the last seguence before the unit was shut off ADVANCED PROGRAMMING MPINAA _ entrydelay off instant someone is in the building and someone is expected to enter no exit delay MPINAC _ entrydelay entry delay instant person staying in the premises is setting the alarm and will not walk in the area monitored by the motion detector Panic button The SC 100 has 2 panic buttons the red buttons on the keychain transmitter and on the Control Panel The alarm will sound instantly when either of these buttons are pressed what ever mode you arein Emergency Silent Alarm works in conjunction with the Emergency Dialer option When disarming the system under duress enter your MPIN then press This will terminate the delay mode and return to the previous arm mode as well as send a signal to the Emergency Dialer which will then send pre recorded messages for help When both power sources are removed from the Control Panel the AC adapter is unplugged and the battery is removed all seguences will return to the above factory default 25 SMARTHOME COM 1 80
29. ssign up to 3 different Secondary Personal ldentification Numbers SPIN For more information on how to change your MPIN and how to add an SPIN see PASSWORDS on page 17 18 We have preprogrammed 6 different arm seguences to meet different cir cumstances For example if you would like the system activated while you are in the premises the motion sensor will be turned off so you have the freedom to move about without setting off the alarm You can personalize any o these preprogrammed arm seguences see Advanced Programming Arming seguences Option 1 Away Seguence To arm your system when you are the last person leaving the premises 1 Press the current MPIN 0 0 0 2 Press B 3 Press C You hear a long beep The arm light and the red lights in zones 3 and 4 go on Both the green and red lights flash in zone 1 for 45 seconds which gives you 45 seconds to leave the premises before the system is activated After 45 seconds both the green and red lights in zone 1 and 2 remain on Upon re entering the premises through zone 1 or walking in the monitored area of the motion sensor zone 2 you have 30 seconds till the alarm sounds The system gives you 30 seconds from the time you enter the premises for example opening the front door to get to the Control Panel to deactivate the system Zones 3 or 4 remain instant If any sensor in zone 3 and 4 are activated the alarm sounds instantly 13 SMARTHOME COM 1 800 SMAR
30. tery Two sets of Door Window Sensors WT 433 each set includes 1 transmitter 1 magnetic switch 1 magnet 2 spacers 1 12 volt alkaline battery installed 1 Motion Sensor PS 433 includes 1 9 volt alkaline battery installed 1 Keychain Transmitter 4B 434 includes 1 12 volt alkaline battery installed 3 Packs of screws and anchors for Control Panel Door Window Sensors and Motion Sensor Sheet of templates Double Sided Tape to aid in the installation of the Control Panel Door Window Sensors and Motion Sensor Warning Stickers 2 pcs Manual Warranty Card Quick Guide OVERVIEW Congratulations You have just purchased one of the most reliable and up to date wireless security systems on the market today Skylink is the first company to in corporate the rolling code technology in a home business security system This innovative technology provides increased security and trouble free wireless connections which greatly reduces false alarms It guarantees that the Control Panel will only recognize radio waves from it s remote sensors door window sensor motion sensor and the keychain transmitter which prevents high tech thieves from duplicating signals and tampering with your system This manual is divided into 6 categories 1 Planning Installation and Testing pages 6 11 explains how to plan a security strategy how to install the Control Panel and the remote devices door window sensor
31. to arm the system when you are the last person leaving the premises see page 13 for information on the Away Seguence Pressing button 1 will give you the same result as pressing MPIN B on the keypad 2 Press button 2 and the Control Panel will beep once The system will be armed in Home Seguence To be used to arm the system when someone remains in the premises see page 14 for information on the Home Seguence Pressing button 2 will give you the same result as pressing MPIN on the keypad 15 SMARTHOME COM 1 800 SMART HOME 949 221 9200 http www smarthome com Order 7307 KEYCHAIN TRANSMITTER 4B 434 TO DISARM THE SYSTEM OR DEACTIVATE THE SIREN USING THE KEYCHAIN TRANSMITTER When the system is armed Press button 3 The red light on the transmitter flashes and the Control Panel beeps twice The system is now disarmed When the siren is sounding Press button 3 The red light on the transmitter flashes and the siren is deactivated THE PANIC BUTTON ON THE KEYCHAIN TRANSMITTER Both the Control Panel and the keychain transmitter are equipped with panic buttons It doesn t matter what mode you are in or even if the system is off once either panic button is pressed the siren comes on instantly The alarm will continue to sound for 180 seconds or until the system is disarmed The panic button on the keychain transmitter is the larger red button The panic button on the Control Panel
Download Pdf Manuals
Related Search