Smart Technologies 710.0026 User's Manual
Contents
1. steps below 1 Power up the receiver by switching the ignition on 2 Place the SmarTire LF Initiator next to each sensor position and press the INITIATE button to cause each sensor to transmit ID number and tire data 3 Check the display to confirm that the signal was received by the receiver wheel position should have turned dark 4 sensors transmission was not received repeat step 2 If the problem persists power down the system and repeat the Programming Sensor ID Number process 710 0026 R1 2 SmarTire LF Initiator Operating Instructions 6 REFERENCE ONLY SMARITRE 6 SMARTIRE PRODUCT amp SERVICE PART WARRANTY EFFECTIVE NOVEMBER 15 2005 This warranty is effective as of November 15 2005 and supersedes all past warranties expressed by SmarTire Systems Ltd Warranty subject to change by SmarTire Systems Ltd at any time without notice Warranty claims must be processed with the Authorized SmarTire Dealer of purchase and not SmarTire Systems Ltd Warranty Policy Subject to the conditions stated herein SmarTire Systems Ltd SmarTire warrants that it s Products and service parts when properly installed in approved applications will conform to Product specifications and will be free from defects in material and workmanship under normal use and service The term of SmarTire s warranty for its Products is 24 months and unlimited mileage commencing on the date of retail sale Dated proof of purchase and2. SMARIIRE SmarTire LF Initiator Tool PN 710 0026 Revision 1 2 Instruction Manual Copyright 2006 SmarTire Systems Inc Duplication of this document in whole or in part for any purposes other than those for which it was originally intended without the written approval of SmarTire Systems Inc is strictly prohibited This manual may be changed by SmarTire Systems Inc at any time and without notice REFERENCE ONLY SMARITIRE 6 TABLE OF CONTENTS INTRODUC TION e e E O EE EA 3 OVERVIEW srira aan aa ceca wes AE E EE EEEE S AE 3 LED FUNG TIONS isnan e A E EA E E A ERE E 4 GETTING STARTED A 4 USING THE LFINITIA TOR r 4 PROGRAMMING SENSOR ID NUMBERG cccccccccsessseeeeeeecceeensseeeeeeececenssseeeeeeeeeoenseeeeesseooonnns 5 VERIFYING CORRECT INSTALLATION 6 SMARTIRE PRODUCT amp SERVICE PART WARRANTY EFFECTIVE NOVEMBER 15 2005 7 710 0026 R1 2 SmarTire LF Initiator Operating Instructions 2 REFERENCE ONLY SMARITRE INTRODUCTION The SmarTire LF Initiator is a handheld tool designed to provoke data transmissions from SmarTire High Pressure Sensors The tool can be used to assist the installer during e New Installations programming sensor ID numbers vehicle configuration into th
3. TE Do not contact the tire or wheel surface when initiating data transmission from a sensor Dual wheel assemblies should always be mounted with valve stems 180 opposite each other OUTBOARD 5 INBOARD PROGRAMMING SENSOR ID NUMBERS sensor ID numbers should be programmed by authorized SmarTire installation facilities using a Dealer Programming Tool DPT When programming a new sensor ID number the installer must first configure the receiver so that it is ready to receive a new ID number and then make the sensor transmit its ID number The steps below describe how to program sensor ID numbers using the LF Initiator 1 After connecting the DPT and installing all sensors power on the system Press and hold the SET button on the DPT for more than two 2 seconds and less than five 5 seconds to enter the Full Programming Mode 2 Press the MODE button on the DPT to toggle between the different programming screens until the learn icon a profile of a head containing a question mark and a computer icon appear on the display The DPT is now displaying the Sensor ID Number Programming screen 3 Press the TIRE button on the DPT to select Sensor ID Number Programming and the ten possible wheel positions for the primary vehicle will be displayed windshield appearing on screen The pre programmed sensor positions are indicated by darkened tire icons 4 Press the TIRE button on the DPT to toggle to the desired wheel
4. claimed parts for return are required The term of SmarTire s warranty for its service parts is 12 months and unlimited mileage commencing on the date of retail sale Dated proof of purchase and claimed parts for return are required The SmarTire warranty will be honored by the authorized SmarTire dealer from which the Product or service part was purchased Subject to warranty approval SmarTire shall at its discretion cover the following Products replacement parts and cost of labor Service Parts replacement parts only SmarTire s obligation to satisfy a warranty claim is subject to yet not limited to the following conditions a dated proof of purchase is provided all Product involved must unless otherwise indicated by SmarTire be returned to the Authorized SmarTire Dealer of purchase and SmarTire s examination of the Product must disclose to SmarTire s satisfaction that none of the Warranty Exclusions described herein apply In all cases SmarTire shall make the final determination as to the warrantability of the Product Products replaced under warranty are covered hereunder by whichever is greater the remaining portion of the original warranty period or 12 months General Limits and Exclusions Coverage 15 not provided for the following failures or expenses a Towing b Downtime lodging meals and travel time or transportation c Troubleshooting Diagnostics except where allowed as indicated in the S
5. e receiver e Sensor Replacement programming new sensor ID numbers into the receiver Installation Verification without moving vehicle e Transmitter De Activation after removal NOTE The SmarTire LF Initiator is compatible with SmarTire s low and high pressure commercial sensors ONLY It is not compatible with the low pressure sensors used in SmarTire products for passenger vehicles motorcycles trailers and tow behinds OVERVIEW Transmission End ED Light Initiate Button 7 s De Energize Button 6 S ve eweraize Learn Button 5 On Switch Battery Cover Initiate Press this button to make a sensor transmit its ID number tire pressure data and tire temperature data This function is used when confirming that sensors are installed in the correct wheel locations on a vehicle after system installation De energize Press this button to de activate a sensor This function should only be used when sensors are removed from a vehicle 710 0026 R1 2 SmarTire LF Initiator Operating Instructions 3 REFERENCE ONLY SMARITRE 6 Learn Press this button to make a sensor transmit Learn transmission Learn transmissions used when reprogramming sensor ID numbers into the SmarTire receiver LED FUNCTIONS Whenever a button is pressed the LF Initiator Tool indicates its status by the color of its LED light e GREEN Working properly approx 5 second illumina
6. ective and in addition it meets the requirements for low powered transmitters receivers as defined by the relevant radio approval authority and complies with low voltage directive 73 23 EEC The directive is designed to provide reasonable protection against harmful interference or susceptibility Changes made to this device without the express approval of SmarTire Europe Ltd may void the 5 authority to use this device SmarTire Systems Inc SmarTire Europe Limited Suite 150 13151 Vanier Place Park 34 Richmond British Columbia Didcot Oxfordshire Canada V6V 2 1 United Kingdom 11 7WB Tel 1 888 982 3001 Tel 44 1235 511010 Fax 1 604 276 0864 Fax 44 1235 514640 Email info smartire com Email info smartire co uk www smartire com www smartire com 710 0026 R1 2 SmarTire LF Initiator Operating Instructions 9 REFERENCE ONLY
7. l transmit its ID number to the receiver Be sure to hold the tool in place until the light turns off to ensure the signal has reached the sensor The tire icon on the display will turn black and the screen will display an X when the sensor s transmission has been received 7 Press the TIRE button to toggle to the next wheel position to be programmed if required and repeat steps 4 6 until all sensor ID numbers that need to be programmed are programmed into their respective locations in the receiver 8 Press the SET button to save all of the sensor ID numbers and their locations into the receivers memory 9 When complete press the SET button to exit and then turn off the system Disconnect the DPT and reconnect the standard display NOTE If ERR appears on the screen and two or more tire icons are flashing two wheel locations have been programmed with the same sensor ID If two identical sensor ID numbers are programmed press the TIRE button to select one of the flashing locations for reprogramming and then repeat steps 4 6 at the flashing locations Repeat for the second location to ensure that the correct sensor ID numbers are programmed Press the SET button to save the revised sensor ID numbers into the receiver VERIFYING CORRECT INSTALLATION To ensure that the system is properly configured after new sensor ID numbers have been programmed in the receiver verify the programming by following the
8. marTire approved guidelines d Freight for expedited or rush parts shipments Parts will be shipped by the most economical means possible e Non genuine replacement parts void the component warranty when used to make a repair f Component damage due to failure of other chassis or vehicle components g Undefined or unidentifiable miscellaneous changes h Failures due to product mis application or SmarTire unapproved application Failures due to unapproved alterations or modifications to the vehicle or the SmarTire component 710 0026 R1 2 SmarTire LF Initiator Operating Instructions 7 REFERENCE ONLY SMARITIRE 6 j Failures caused by improper installation or improper prior repair including damage Product by tire tyre removal or installation k Corrosion and rust Tires tyres m Failures due to dirt snow or ice build up n Accident damage negligence abuse or misuse All returned Products become the property of SmarTire and will be returned SmarTire s determination of warranty coverage shall be final in all cases SmarTire reserves the right to reject warranty claims for any or all of but not limited to the following reasons a Proof of purchase was not provided b Failure occurred beyond applicable warranty period c Claim information is insufficient d Product was not returned for inspection as requested e Product inspection does not substantiate claim or indicate a failure Wa
9. omply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions 710 0026 R1 2 SmarTire LF Initiator Operating Instructions 8 REFERENCE ONLY SMARITIRE may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Changes or modifications to this device without the express approval of SmarTire Systems Inc may void the user s authority to use this device EUROPEAN REGULATIONS This device complies with R amp TTE 1999 5 EC through harmonized standards EN301 489 1 and EN330 330 1 The equipment has been tested and found to comply with the above dir
10. position The flashing tire outline indicates the selected wheel position When toggled past the primary vehicle the display will show possible wheel positions for a tow behind vehicle Continue toggling past the axles of the two behind vehicle to once again access the primary vehicle 710 0026 R1 2 SmarTire LF Initiator Operating Instructions 5 REFERENCE ONLY SMARITIRE 6 5 Ifa sensor ID number is already programmed in the selected wheel position indicated by filled in tire icon and an X on the screen the ID number must be erased before a new ID number can be programmed Press the MODE button to erase the pre programmed ID number the X will disappear and then press the MODE button again to select the wheel position for programming check mark will be displayed If a sensor ID number does not exist at the selected location simply press the MODE button once to select the highlighted wheel position for programming 6 The receiver is now ready to receive the new sensor ID number Turn on the LF Initiator Tool and go to the tire that contains the new sensor to be programmed into the receiver Position the transmission end of the LF Initiator Tool approximately 1 inch 2 5 cm away from the tire s surface positioned at the center of the tire s sidewall at the location of the valve stem sensor should be installed near the valve stem Press the LEARN button on the LF Initiator Tool and the sensor wil
11. rranty Disclaimer SMARTIRE S EXPRESS WARRANTY AND PURCHASER S REMEDIES THEREUNDER ARE EXCLUSIVE AND GIVEN IN PLACE OF a ALL OTHER WARRANTIES EXPRESS IMPLIED OR STATUTORY WHETHER WRITTEN OR ORAL INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY FITNESS FOR PARTICULAR PURPOSE OR IMPLIED WARRANTY ARISING FROM PERFORMANCE COURSE OF DEALING OR USAGE OF TRADE AND b ALL OTHER OBLIGATIONS LIABILITES RIGHTS CLAIMS OR REMEDIES INCLUDING ANY RIGHT IN CONTRACT TORT EXTRA CONTRACTUALLY STRICT LIABILITY OR ANY RIGHT ARISING FROM SMARTIRE S NEGLIGENCE ACTUAL OR IMPUTED YOUR STATUATORY RIGHTS ARE NOT AFFECTED Limitation of Liability SMARTIRE S OBLIGATIONS AND PURCHASER S REMEDIES UNDER SMARTIRE S EXPRESS WARRANTY ARE LIMITED TO SMARTIRE S CHOICE OF REPAIR CREDIT OR REPLACEMENT AND EXCLUDE LIABILITY FOR INCIDENTAL SPECIAL CONSEQUENTIAL OR ANY OTHER DAMAGES INCLUDING WITHOUT LIMITATION REPLACEMENT COSTS ECONOMIC LOSS LOST REVENUE LOST PROFITS OR LOSS OF USE OR DAMAGE TO OTHER PROPERTY PRODUCTS ARE CONSIDERED TO BE MONITORING DEVICES AND ARE NOT TO BE CONSIDERED AS SAFETY DEVICES FCC NOTICE This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to c
12. tion duration RED Not working properly contact SmarTire distributor for replacement e ORANGE Low battery voltage GETTING STARTED The SmarTire LF Initiator is powered by a standard 9 Volt battery To install the battery open the battery access panel on the back of the tool and connect the supplied battery to the 9 Volt battery connector Insert the battery into the slot and close the battery access panel Push the ON OFF switch up to power the tool on and down to power it off USING THE LF INITIATOR The SmarTire LF Initiator Tool is very easy to use Simply hold it approximately 1 inch 2 5 cm away from the tire s surface positioned at the center of the tire s sidewall at the location of the valve SmarTire sensors should be installed at the valve and their location should also be indicated by rim mounted label Press but do not hold down the button and hold the tool in place for approximately 5 seconds to ensure the wireless signals emitted from the tool reach the sensor 710 0026 R1 2 SmarTire LF Initiator Operating Instructions 4 REFERENCE ONLY SMARITIRE gt dual wheel assemblies position the LF Initiator Tool approximately 1 inch 2 5 cm away from the tire s surface positioned at the center of the outboard tire s sidewall opposite the valve stem The transmission from the tool will pass through the outboard tire and provoke a data transmission from the sensor mounted on the inboard tire NO
Download Pdf Manuals
Related Search