SkyLink WR-001 User's Manual
Contents
1. 1 Power off the Wall Dimmer by placing the air gap switch to off position 2 Press and hold the SET button while holding the SET button slide the air gap switch to on position 3 The blue LEDs will be on first then flashes rapidly for 1 second 4 You may release the SET button now you have successfully erased all the devices 10 TECHNICAL SPECIFICATIONS Input Voltage 120V AC 60Hz Standby Current 0 2mA Minimum Load 10W Maximum Load 600W at 120VAC Operating Frequency 318MHz Operational Temperature 4 F 140 F 20 C 60 C Humidity 5 95 Range Up to 500 feet in open area 11 FCC The Device is approved by the FCC and it complies with Part 15 of the FCC Rules Its operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference that may cause undesired operation WARNING Changes or modifications to this unit not expressly approved by the party responsible of compliance could void the user s authority to operate the equipment Fe c US LISTED CUSTOMER SERVICE 17 Sheard Avenue Brampton Ontario Canada L6Y 1J3 Email support skylinkhome com http www skylinkhome com P N 101Z713 Patent Pending 2010 SKYLINK GROUP 12 WARRANTY If within one year from date of purchase this product should become defective except battery due to faulty workmanship or materials it will be repaired or replaced with2. therefore extending the On period by another timer interval To stop timer count down press a programmed button for regular mode 5 REGULAR OPERATING MODE The Wall Dimmer can control the light in 2 different operating modes 1 On Off Mode Allows operating the light either on or off without dimming function 2 Dimming Mode Allows operating the light in on off or dimming dim brighten Light source must be either incandescent light or dimmable compact fluorescent light The factory default operating mode is On Off mode However if your light is dimmable you may change the operating mode to Dimming Mode To change the operating modes please follow the instructions below 5 REGULAR OPERATING MODE CONT 1 Turn on the light by the programmed transmitter or touch pad 2 Press and hold the button on the transmitter that is programmed to the Wall Dimmer for 10 seconds or touch the touch pad for 10 seconds with your finger 3 The light will flash If it flashes once that means it is in On Off Mode If it flashes twice that means it is in Dimming Mode 4 Repeating step 2 above will toggle the setting between On Off Mode and Dimming Mode 5 1 ON OFF operation Use the Wall Dimmer To turn on off the light simply tap the touch pad of the wall dimmer once with your finger it will toggle the status of the light i e from on to off or from off to on Use a Transmitter Wall Dimmer allows on off ope
3. Wall Dimmer Model WR 001 1 INTRODUCTION Thank you for your purchase of a SkylinkHome lighting receiver Wall Dimmer Model WR 001 Simply replace your existing wall switch with this Wall Dimmer you can then wirelessly turn on and off dim and brighten lights with a SkylinkHome transmitter The Wall Dimmer WR 001 can communicate with up to 8 transmitters so user has the option to add more transmitters to the system such as more remote controls or motion sensors etc All wireless signal communications within the SkylinkHome System are based on rolling code technology to ensure highest security is used The following items are included in this package Wall Dimmer Wire nuts User s Instructions Wall Dimmer WR 001 a P Wire nuts 2 SETUP Setup of the Wall Dimmer is simple Simply replace your existing wall switch by the Wall Dimmer CAUTION amp Installation is required and enclosed instructions must be followed carefully to all steps and notes If you are uncertain or uncomfortable performing this installation please consult a qualified electrician This manual should also be retained for future reference 1 Turn off power to the circuit that you plan on installing the Wall Dimmer to at the circuit breaker WARNING Failure to turn off power at the circuit breaker can result in electrical shock causing severe or fatal injury Note Lighting Load The Wall Dimmer is designed to ope
4. all Dimmer Each module can be operated by up to 8 different transmitters or 8 different command signals There are 3 operating modes with the Wall Dimmer 1 Regular Mode When a valid signal is received it will turn on or off the light or change the brightness of the light 2 Flashing Alert Mode When a valid signal is received the light will flash for a specific period of time which is the time defined in the timer duration This works as an alert indication 3 Countdown Timer Mode When a valid signal is received the light will be on for a specific period of time 1 minute 5 minutes 15 minutes 30 minutes or 60 minutes This is mainly for energy saving You can program multiple buttons transmitters sensors to the module and different button transmitter sensor can activate a different mode To program a TC series transmitter into the Wall Switch Dimmer under regular mode follow the instructions below 1 Wall Dimmer must be installed and powered properly Touch the touch pad The connected light should be on and the 2 blue LEDs are off 2 Press and hold the SET button for about 3 seconds until the upper blue LED flashes quickly 3 You may now release the SET button The blue LED will continue to flash quickly for about 15 seconds Operating Mode Upper LED Indication Regular Flashes quickly Flashing Alert Flashes slowly Countdown Timer Steadily On PROG
5. button 4 Within 15 seconds follow steps A to C veas A Press the PROG button on the back of the TC transmitter with a sharp object B Press the button on the TC transmitter that you would like to program C Once the transmitter is programmed the two blue LEDs on the Wall Dimmer flash quickly then stop flashing indicating you have successfully programmed the trans mitter to the module Now the programmed transmitter button is ready to be used for Regular Mode Press the desired button To program a TC series transmitter into the Wall Switch Dimmer under Flashing Alert Mode follow the instructions below 1 Wall Dimmer must be installed and powered properly Touch the touch pad The connected light should be on and the 2 blue LEDs are off 2 Press and hold the SET button for about 9 seconds until the upper blue LED flashes slowly 3 You may now release the SET button The blue LED will continue to flash slowly for about 15 seconds 4 Within 15 seconds follow steps A to C A Press the PROG button on the back of the TC transmitter with a sharp object B Press the button on the TC transmitter that you would like to program C Once the transmitter is programmed the two blue LEDs on the Wall Dimmer flash quickly then stop flashing indicating you have successfully programmed the transmitter to the module Now the programmed transmitter button is ready to be used for Flashing Alert Mode To program a TC s
6. en release the button Press and hold the same button again on the transmitter to change the brightness again in the opposite way When the desired brightness is reached release the button Note Press and hold for more than 10 seconds will toggle the mode between ON OFF and Dimming 6 FLASHING ALERT OPERATING MODE If a transmitter or a sensor is programmed to the Wall Dimmer under the flashing alert mode when that transmitter is activated the light connected will flash for the predetermined timer interval The brightness of the light can only be set under regular mode After the timer interval the light will be off Pressing a programmed button for regular mode can override flashing alert operation 7 COUNTDOWN TIMER OPERATING MODE If a transmitter or a sensor is programmed to the Wall Dimmer under the countdown timer mode when that transmitter is activated the light con nected will be on for the predetermined timer interval The brightness of the light can only be set under regular mode After the timer interval the light will be off Pressing a programmed button for regular mode can override countdown timer operation 8 ZONE OPERATION An optional deluxe remote is needed for zone operation A Zone Command allows you to operate multiple lights altogether in the same zone A zone command must first be programmed to the receiver before zone operation To program a zone command please refer to the user s instructions
7. eries transmitter into the Wall Switch Dimmer under Countdown Timer Mode follow the instructions below 1 Wall Dimmer must be installed and powered properly Touch the touch pad The connected light should be on and the 2 blue LEDs are off 2 Press and hold the SET button for about 15 seconds until the upper blue LED will be steadily on 3 You may now release the SET button The blue LED will continue to be on for about 15 seconds 3 PROGRAMMING TRANSMITTERS TC SERIES SENSORS CONT 4 Within 15 seconds follow steps A to C A Press the PROG button on the back of the TC transmitter with a sharp object B Press the button on the TC transmitter that you would like to program C Once the transmitter is programmed the two blue LEDs on the Wall Dimmer flash quickly then stop flashing indicating you have successfully programmed the transmitter to the module Now the programmed transmitter button is ready to be used for Countdown Timer Mode To program other transmitters sensors please refer to the instructions of those transmitters sensors and above instructions Note You must complete the programming sequence within the 15 second interval otherwise the Wall Dimmer will quit from programming mode and you need to start again from step 1 4 SET TIMER DURATION As mentioned the timer can be set to the following durations 1 minute 5 minutes 15 minutes 30 minutes or 60 minutes This timer duration is used f
8. of the deluxe remote Zone Operation On Off To turn on or off a zone hold Jor until the red LED flashes three times and keeps on then release the held button and press the zone number For example Hold O until the red LED flashes three times and keeps on then release ry and press 1 all lights in zone 1 will be turned on Hold until the red LED flashes three times and keeps on then release 9 and press 1 all lights in zone 1 will be turned off Zone Operation Brightness Control You can also change the brightness of lights in a zone altogether if the receiver modules and all lights connected are dimmable If non dimmable lights or appliances are connected to a zone do not operate Zone Brightness Control For example Hold until the red LED flashes three times and keeps on then release and hold 1 all lights in zone 1 will be brightened you may release 1 at the desired brightness level Hold 1O until the red LED flashes three times and keeps on then release and hold 1 all lights in zone 1 will be dimmed you may release 1 at the desired brightness level 9 ERASING TRANSMITTERS FROM THE MODULE You may erase a transmitter or sensor from the wall dimmer but you cannot erase a specific device directly you must erase all the wireless devices then program the ones you want to keep Follow the instructions below to erase programmed transmitters sensors
9. or both under Flashing Alert Operating Mode and Countdown Timer Operating Mode There is only one timer setting so all transmitters that are programmed for timer mode and flashing mode will have the same timer duration To set the timer duration follow the instructions below 1 Wall Dimmer must be installed and powered properly The connected light should be off and the 2 blue LEDs are on The light must be off in order to set the timer duration 2 Press and hold the SET button for 3 seconds the lower blue LED flashes once The number of flashes indicates the timer duration Number of Flashes Timer Duration 1 1 min 2 5 min 3 15 min 4 30 min 5 60 min 3 Continue to hold the SET button until it reaches the desired setting The status will change every 6 seconds i e hold the SET button for another 6 seconds you will see the number of flashes changes from 1 to 2 2 to 3 etc Note Once the number of flashes reaches 5 it will stay at this setting If you would like to go back to other settings such as 1 minute release the button and repeat from step 1 to start over Once a transmitter button is programmed for timer mode or flashing mode activating this programmed transmitter button will turn on the light for the specified timer duration During a timer count down if the Wall Dimmer receives another signal for timer operation the timer will start again and overrides the previous timer
10. out charge Proof of purchase and a Return Authorization are required 13 CUSTOMER SERVICE If you would like to find out the up to date specifications know more about features and applications download documents i e user s instructions order Skylink products or if you have difficulty getting products to work please 1 visit our FAQ section at www skylinkhome com or 2 email us at support skylinkhome com or 3 call our toll free at 1 800 304 1187 from Monday to Friday 9 am to 5 pm EST Fax 800 286 1320 14 ACCESSORIES The SkylinkHome System consists of many other devices such as SkylinkHome Remotes Motion Sensor ON OFF Wall Switch Wall Dimmer Plug In Dimmer with or without Repeater Plug In ON OFF Control Outdoor Indoor Screw In Dimmer ON OFF Dimming Control ON OFF Control Smart Button Garage Door Control etc Please visit Skylink website at www skylinkhome com for more information V2 0
11. rate incandescent light or dimmable compact fluorescent light with a maximum load of 600W at 120VAC Light bulbs must be dimmable in order to achieve dimming function 2 Follow the diagrams below to install the Wall Dimmer with the 2 wires Live Load Use the provided wire nuts to connect these wires respectively to the existing wires from the wall Load Red to load and Live Black to live 3 After all the wires are connected ensure that all of the wire connectors are attached securely and there should be no exposed copper wiring Secure the Wall Dimmer with the provided screws Place the air gap switch to off position Turn the circuit breaker back on Place the air gap switch to on position The two blue LEDs will be on The light connected will be off The Wall Dimmer is now installed and you can tap the metal touch pad to turn ON OFF the connected light or to begin programming to learn transmitters into the Wall Dimmer NOS Air Gap Switch Touch Pad Blue q LED SET Button Grey Antenna Do not cut the antenna Note Antenna grey wire Do not cut it keep it as straight as possible Put the antenna directly into the dry wall or through a hole of the metal box into the dry wall to get more control distance with a remote 3 PROGRAMMING TRANSMITTERS TC SERIES SENSORS In order to operate the Wall Dimmer remotely with a transmitter or sensor it must be programmed to the W
12. ration when the programmed button is pressed it will transmit a signal to toggle the status of the load For example if a toggle signal is received when the light is off that signal will turn on the light If you have a deluxe remote you can make sure that you will actually turn on a light by pressing 10 first then the programmed button Similarly you can make sure that you will turn off a light by pressing KQ first then the programmed button If you have a deluxe remote and you press all those receivers to which the remote is programmed will turn on their loads If you press 1 all those receivers to which the remote is programmed will turn off their loads 5 2 Brightness control operation Besides turning on and off the light you may also control the brightness of the light if the light bulb is either incandescent light or dimmable compact fluorescent light Use the Wall Switch Turn on the light first Then keep touching the touch pad to change the brightness Remove your finger from the touch pad until the desired brightness is reached To change the brightness in the opposite way remove your finger from the touch pad and then keep touching again remove the finger from the touch pad until the desired brightness is reached Use a Transmitter First turn on the light Then press and hold the programmed button on the transmitter to change the brightness Hold the button until the desired brightness is reached th
Download Pdf Manuals
Related Search