Home
SkyLink PS-434A User's Manual
Contents
1. at support skylinkhome com reply within 24 hrs or 3 call our toll free at 1 800 304 1187 from Monday to Friday 9 am to 5 pm EST Fax 800 286 1320 for customers in USA amp Canada only CE CUSTOMER SERVICE 17 Sheard Avenue Brampton Ontario Canada L6Y 1J3 Email support skylinkhome com Reply within 24 hrs http www skylinkhome com P N 101A255 Rev 0 US Patent 6243000B1 2004 SKYLINK GROUP
2. Motion Sensor Model PS 434A 1 INTRODUCTION The Motion Sensor is designed to monitor movement around your house It can be placed either indoor or outdoor In this package you should find a Motion Sensor battery included ball head joint and screws J 2pcs 3x 18 screws Included Ball head joint Motion Sensor battery included Please follow the instructions below to setup your motion sensor 2 SET UP THE MOTION SENSOR 1 POWER UP Insert a 9V alkaline battery to the motion sensor The sensor requires a warm up time of approx 45 seconds before it can function properly Insert 9V alkaline battery to the sensor 2 PROGRAM THE MOTION SENSOR TO THE SECURITY CONTROL PANEL SC 001 i Enter the current MPIN Master Identification Number in the Security Control Panel SC 001 i Press B ii Press the number key to identify which zone to add the Motion Sensor to 1 2 3 4 We recommend you program the motion sensor to zone 2 The zone light will flash for eight seconds iv While the zone light is flashing press v While the zone light is flashing press the Learn Button inside the battery compartment diagram 1 of the Motion Sensor in order to activate it You will hear a long beep if the motion sensor is learned to the control panel The zone light will stop flashing and the remote sensor will now communicate to that zone 3 PROGRAM THE MOTION SENSOR TO THE AUDIO ALARM AA 433 i
3. With only the ON light lit on the Audio Alarm press and hold the learn button located on the bottom of the Audio Alarm ii While pressing down on the button press the Learn Button inside the battery compartment diagram 1 of the Motion Sensor in order to activate it iii If a connection has been made the Audio Alarm will stop beeping and make a continuous tone until the black learn button on the Audio Alarm is released 4 PROGRAM THE MOTION SENSOR TO THE EMERGENCY DIALER AD 433S AD 1010 ED 1010 i Press L 5 when in clock mode the display will show L5 Id code ii Within 5 seconds press the Learn Button inside the battery compartment diagram 1 of the Motion Sensor in order to activate it The display will return to clock mode once the Motion Sensor has been learned iii If the Motion Sensor detects any movement it will trigger the Emergency Dialer and start dialing the preset phone numbers refer to AD 433S AD 1010 ED 1010 User s Instruction 5 SENSOR SENSITIVITY The sensitivity of the motion sensor is adjustable Change the setting by placing the connector on either the High or Low position When the sensitivity is set to Low more movement is required to trigger the sensor It is recommended to set the sensitivity to Low and perform a Walk Test Described in Section 3 Walk Test If the walk test result is satisfied the sensitivity does not require to be
4. adjusted further If the walk test result shows the sensitivity is too low then you can change the sensitivity setting to High Please perform the walk test after changing the sensitivity setting Learn button Sensitivity Connectors on Motion Sensor Diagram 1 3 INSTALLING THE MOTION SENSOR 1 MOUNTING A ball head joint is necessary to mount the sensor at a desire location A height of 5 6 ft is recommended depending on your application Once a location is selected mount the ball head joint to this location by screws provided see diagram 2 Once the ball head joint is mounted to the wall slide the back of the sensor into the ball head joint see diagram 3 The mounting angle can be adjusted Please refer to Section 3 Walk Test to determine the best mounting angle Diagram 3 Diagram 2 2 WALK TEST After mounting the sensor at the desired location it is important to perform a walk test in order to determine if the sensor is detecting the things you want to detect In order to control how far the sensor can see this can be done by adjusting the angle of the sensor To reduce the detection range simply move the sensor downward To increase the range move the sensor up to around 12 degrees This will give the maximum range However this may not be desired if the sensor is placed outdoors since a false trigger may occur if the sensor is set to detect motion in a distance Disarm the contro
5. h the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful inter ference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment dose cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 5 WARRANTY If within one year from date of purchase this product should become defective except battery due to faulty workmanship or materials it will be repaired or replaced without charge Proof of purchase and a Return Authorization are required 6 CUSTOMER SERVICE If you would like to order Skylink s products or have difficulty getting them to work please 1 visit our FAQ website at www skylinkhome com or 2 email us
6. l panel or dialer before you perform the work test or you will trigger an alarm please refer to the user s instruction of your receiver You should walk in the area that you would like the sensor to monitor If movement is detected the red light inside the unit will appear If the red light does not appear adjust the mounting angle accordingly Perform the walk test again after 30 seconds Repeat this procedure until your motion is detected There should be no movement in the detected area during the 30 seconds Perform walk test in the undesired area to ensure movement cannot be detected Tips The sensor should not face towards direct sunlight placing near heat or cold producing devices i e A C or furnance vents fans Rai Move the sensor up Move the sensor ovens heaters etc that may downward to to around 12 to give cause false triggers reduce the range maximum range 4 FCC This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply wit
Download Pdf Manuals
Related Search
Related Contents
ヒートファルト Copyright © All rights reserved.
Failed to retrieve file