SkyLink MK-318-3 User's Manual
Contents
1. Model MK 318 1 Model MK 318 2 Model MK 318 3 3 Button Garage Door Remote Control 1 INTRODUCTION Thank you for your purchase of Skylink Remote Model MK 318 1 MK The following items are included in this package One of MK 318 series Remotes Lithium Battery CR 2032 Installed RS w User s Instructions 1 Button 2 Button 3 Button Transmiter Transmiter Transmiter MK 318 1 MK 318 2 MK 318 3 There are one or two or three buttons on transmitter each button can be programmed to control Skylink garage door receiver Smart Button GB 318 or Skylink garage door opener directly Follow one or more instructions below in Section 2 to program transmitter MK 318 to the receiver or receivers you want to control 2a PROGRAM TRANSMITTER TO RECEIVER GB 318 You need to do the programming in order to add the transmitter remote control to a receiver Refer to the receiver Smart Button GB 318 user s instruction to set up the unit Smart Button GB 318 can learn up to 10 remote controls To program the transmitter to the receiver follow the instructions below 1 Press the learn button on the side of the Smart Button GB 318 2 Once the learn button is pressed the LED will flash quickly Release the learn button 3 Within 30 seconds press any one of the 3 buttons on the transmitter that you want to program to the receiver 4 Once the remote control is programmed the LED will flash slowly in the same2. above password input The factory default password is 2 2 2 and this password function is disabled out of factory Change password 1 Press 1 and 3 simultaneously and hold for more than 6 seconds until the LED changes from flashing quickly to flashing slowly 2 Input old password 3 Press 1 and 3 once simultaneously to confirm If the password is wrong the LED will flash 3 times and you have to start it over from step1 4 Input new password 5 Press 1 and 3 once simultaneously to confirm 6 Input new password again 7 Press 1 and 3 once simultaneously to RE confirm If the password is different from the one of step 4 the LED will flash 3 times and you have to start over from step 1 Otherwise the password has been changed to the new one and the password protection is enabled Disable password 1 Press 1 and 3 simultaneously and hold for more than 2 seconds until the LED flashes quickly but not until the LED flashes slowly 2 Input old password 3 Press 1 and 3 once simultaneously to confirm If the password is correct the password protection will be disabled 5 ADVANCED FEATURE PASSWORD PROTECTION CONT Enable password 1 Press 1 and 3 simultaneously and hold for more than 2 seconds until the LED flashes quickly but not until the LED flashes slowly 2 Input old password 3 Press 1 and 3 once simultaneously to confirm If the password is correct the password protection will be enabled You c
3. an toggle the two states password protection enabled or disabled Note The time out period is 10 seconds during any of the above setting operations After 10 seconds the LED will flash 3 times and the remote will exit from setting If you forget your password and want to reset MK 318 3 follow the steps below 1 Press 1 and 2 simultaneously and hold for more than 10 seconds until the LED flashes 2 After you release 1 and 2 the LED will be turned off and MK 318 3 will be reset The password will be reset to factory default After the reset password protection is removed but the remote can not control any receiver until you reprogram it to receivers you want to control This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency e
4. ax 800 286 1320 CUSTOMER SERVICE 17 Sheard Avenue Brampton Ontario Canada L6Y 1J3 Email support skylinkhome com http www skylinkhome com PIN 101Z993 002 Patent Pending 2010 SKYLINK GROUP
5. nergy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 7 WARRANTY If within one year from date of purchase this product should become defective except battery due to faulty workmanship or materials it will be repaired or replaced without charge Proof of purchase and a Return Authorization are required 8 CUSTOMER SERVICE If you would like to find out the up to date specifications know more about features and applications download documents i e user s instructions order Skylink products or if you have difficulty getting products to work please 1 visit our FAQ section at www skylinkhome com or 2 email us at support skylinkhome com or 3 call our toll free at 1 800 304 1187 from Monday to Friday 9 am to 5 pm EST F
6. series Garage Door Opener please follow the user s instruction from the Garage Door Opener 3 TROUBLE SHOOTING Q What can do if the door opener does not react after press the button on the transmitter A Ensure when the button on the transmitter is pressed the red light on the transmitter comes on Otherwise check if the battery is inserted properly Make sure the correct button on the transmitter is pressed Ensure the wires that were previously connected to the wall mounted door control are not loose Ensure the transmitter has been programmed to the receiver Refer to section 2 for how to program a transmitter to the receiver 4 BATTERY 3 Volt lithium battery CR 2032 included It is time to change the battery when the red LED on the transmitter does not turn on when either button is pressed 5 ADVANCED FEATURE PASSWORD PROTECTION Password protection Only available for MK 318 3 Not available for MK 318 1 or MK 318 2 The MK 318 3 can be password protected If you enable the password protection you can only operate MK 318 3 after you input the correct password Password can be 2 8 digits long which is a combination of 1 2 and 3 For example password can be 1 2 1 2 To input this password you have to press button 1 then 2 then 1 then 2 Note 1 Button 1 2 Button 2 3 Button 3 Button 1 Button 2 Button 3 Note The time out period is 1 second during
7. way as it flashes in standby mode 5 You may now operate the garage door opener with this new remote control 6 To program this transmitter to control another Smart Button receiver repeat process 1 to 4 to program GB 318 another button on the remote control Antenna Learn Button 2b PROGRAM A TRANSMITTER TO THE SKYLINK GARAGE DOOR OPENER EQ SERIES You need to do the programming in order to add the transmitter to a Skylink Garage Door Opener Skylink Garage Door Opener can learn up to 16 remote controls To program the transmitter to the Garage Door Receiver follow the instructions below 1 Press the LEARN SET button once on the garage door opener 2 Once the LEARN SET buttton is pressed the LEARN LED will flash You may release the LEARN SET button 3 Within 30 seconds press any one of the 3 buttons on the transmitter that you want to program to the receiver 4 Once the transmitter is programmed the LEARN LED will turn off 5 You may now operate the garage door opener with this new transmitter 6 To program a transmitter to control another garage door opener repeat process 1 to 4 to program another button on the transmitter Learn Button o d OIO OIO Up Down Learn Set Wall Button Safety Beam 2c PROGRAM A TRANSMITTER TO THE SKYLINK GARAGE DOOR OPENER IQ SERIES To program the transmitter to the Skylink IQ
Download Pdf Manuals
Related Search