SkyLink GT-115 User's Manual
Contents
1. 4 BATTERY The Keypad Transmitter operates on two 3 volt lithium batteries CR2032 This transmitter comes with the batteries already installed It is time to replace the batteries when the low battery indication is on Low battery condition is indicated by the LO BATT light on when the keypad is activated To replace the batteries 1 Remove the keypad transmitter from the wall 2 Undo the screw on the back of the unit 3 Use a screwdriver to open the battery compart ment by rotating it 4 Remove the batteries from the battery com partment 5 Place the new batteries in position See diagram 6 Close the battery compartment and reinsert the screw CCESSO Optional accessories can be added to the garage door closer 4 Button Keychain Remote Model 4B 201 Keychain remote can be programmed to the garage door closer so it operates the garage door opener like an ordinary remote control It transmits Skylink rolling code Multiple buttons allow operation of multiple garage door openers and lighting appliances control 12V Alkaline battery included Garage Door Monitor Sensor Model GS 101 Detects garage door position Patented sensing technology Closes garage door automatically with the preset l timer when work in conjunction with Garage One Lithium battery included 5 ACCESSORIES CONT Audio Sensor Model AS 101 The Audio Sensor is to be2. Keyless Entry System Model GT 115 1 INTRODUCTION Congratulations on your purchase of the Skylink Garage One Keyless Entry System This is a keypad transmitter receiver kit where the receiver simply replaces your existing garage door opener s push button or wall console Installation is very simple follow the instructions below to install the Garage One receiver GT 100R This kit comes with the following items Zy i Keypad Transmitter Batteries included lt Extension wires Garage One GT 100R 2 INSTALLATION Garage One The GT 100R Garage One replaces most garage door push buttons or wall consoles There are 2 different kinds of push buttons 1 Single button i 2 Multi Function Wall Console 1 Single button If your garage door opener equips with a single button push button you can replace the existing push button with Skylink Garage One GT 100R Please follow the procedures below 1 5 6 Disconnect the 2 wires that are connected to After connecting the 2 wires the red LED under Remove the existing push button by removing the screws A w Remove existing wires the existing push button Connect these 2 wires to the 2 terminals on the Garage One GT 100R Loosen the 2 screws on the terminals feed the 2 wires to the 2 terminals and tighten 2 screws to secure the 2 wires neath the push button will be o
3. ON CONT Antenna Push button Loss of Signal LED Timer Learn LED Lock button Learn button Learn Button To program Skylink s remote control sensor 1 Press the learn button for approx 5 seconds 2 The Timer Learn red LED will be on release the learn button 3 Activate the Skylink remote control If the Skylink remote control has multiple buttons press the button you would like to operate 4 The Timer Learn LED will be off after it has successfully programmed the remote control 5 You can now press the programmed remote to operate the garage door opener Erase Skylink remote controls sensors To erase unwanted remote control s first erase all remote controls and sensors then program the ones you would like to keep Erase all remote controls sensors 1 Press and hold the learn button for 15 seconds 2 The Timer Learn red LED will flash rapidly meaning all remote have been erased 3 You have now successfully erased all the remote controls and sensors Follow the instructions To program Skylink s remote control to add the remote control s you would like to keep Push Button Press the push button to open or close the garage door Lock Button Lock feature is designed to prevent Skylink handheld remotes such as Skylink Keychain Remote Model 4B 201 sold separately to operate the garage door opener To activate the lock feature 1 Press and hol
4. USTOMER SERVICE 17 Sheard Avenue Brampton Ontario Canada L6Y 1J3 Email support skylinkhome com http www skylinkhome com PIN 101A449 US Patent 6243000B1 Patent Pending are registered trademarks of their respective corporations 2006 SKYLINK GROUP
5. Wall Console Connect the 2 wires from the GT 100R to the 2 terminals marked RED and WHT on your existing Multi Function Wall Console Polarity DOES NOT matter Note Do not remove the existing wires from your Multi Function Wall Console Genie Deluxe Wall Console For the Genie Deluxe Wall Console depending on whether the lock feature will be used Parallel Connection 1 If the lock feature will not be used you can simply replace the Genie Deluxe Wall Console with a Skylink GT 100R To replace a multi function wall console follow the same procedure as to replace a Single button wall console If the lock feature will be used you need to connect the Skylink GT 100R in parallel with the Genie Deluxe Wall Console and an additional trans former sold separately is needed Follow the instructions below Remove the existing push button by removing the screws Remove the 2 screws that secure the wires on the Genie wall console Extension Connect one end of the extension wires provided x wires in this kit to the 2 terminals on the Genie wall console the other end to the 2 terminals on the GT 100R wall console Polarity DOES NOT matter Note Do not remove the existing wires from the Geni amp wall console After connecting the 2 wires the red LED under neath the push button will be on The GT 100R Van is now charging up The GT 100R will be fully a cha
6. d the lock button for approx 2 seconds then release it 2 When the lock feature is activated the red LED underneath the push button will flash rapidly Note If a valid wireless remote signal is received while the lock feature is activated Garage One will beep to reminding you the Garage One is locked To deactivate the lock feature 1 Press and hold the lock button for approx 2 seconds then release it 2 When the lock feature is deactivated the red LED underneath the push button will flash slowly indicating the Garage One is in normal operating mode and the lock feature is deactivated 3 OPERATION CONT Chamberlain Lift Master Sears Craftsman Multi Function Wall Console There are 3 buttons on the Multi Function Wall Console 1 Push Button Open Close garage door 2 Lock Button Enable Disable handheld remotes to operate the garage door opener 3 Light Button Turn on off light Skylink Garage One also has 3 buttons their functions are identical to the Chamberlain Lift Master Sears Craftsman wall console Chamberlain Lift Master Function Equivalent button on Sears Skylink Garage One Push Bar Open Close door Push Button Lock Button Enable Disable operation Lock Button from handheld remotes Light Button Turn light on off Learn Button Light Button Chamberlain Prevents operation from handheld remotes Turn light on off
7. lar installation If this equipment dose cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 7 WARNING To prevent possible SERIOUS INJURY or DEATH from a closing garage door Activate door ONLY when it can be seen clearly is properly adjusted and there are no obstructions to door travel ALWAYS keep garage door in sight until completely closed NEVER permit anyone to cross path of closing garage door 8 WARRANTY If within one year from date of purchase this product should become defective except battery due to faulty workmanship or materials it will be repaired or replaced without charge Proof of purchase and a Return Authorization are required 9 CUSTOMER SERVICE If you would like to order Skylink s products or have difficulty getting them to work please 1 visit our FAQ section at www skylinkhome com or 2 email us at support skylinkhome com or 3 call our toll free at 1 800 304 1187 from Monday to Friday 9 am to 5 pm EST Fax 800 286 1320 C
8. n The GT 100R is now charging up The GT 100R will be fully charged when the buzzer emits a beep approx 10 seconds to 1 minute depending on the brand of garage door opener the red LED will then flash slowly The GT 100R is now ready to operate Mount the Garage One to the wall with 2 screws Straighten up the antenna on the GT 100R 2 Multi Function Wall Console Multi Function Wall Console normally comes with 3 buttons that can be used to 1 operate the garage door opener lighting 2 lock the receiver so it doesn t accept remote control operation and 3 push button for door opening closing Depending on the brand of garage door opener you have the installation is different 2 INSTALLATION CONT Multi Function Wall Console for Chamberlaine Lift Master Sears Craftsmane Skylink GT 100R Garage One also has 3 buttons It can replace Chamberlain Lift Master and Sears Craftsman Multi Function Wall Console directly That means if you have any one of these wall consoles you can simply remove the existing wall console and replace it with a Skylink GT 100R To replace a multi function wall console mentioned above follow the same proce dure as to replace a Single button wall console If your Chamberlain LiftMaster and Sears Craftsman Multi Function Wall Console has more than 2 wires the Skylink GT 100R should be installed in parallel with the original Multi Function
9. rged when the buzzer emits a beep approx 10 seconds to 1 minute depending on the brand of garage door opener the red LED will then flash slowly The GT 100R is now ready to operate 5 Mount both w all consoles to the wall with screws o Straighten up the antenna on the GT 100R Plug in the transformer sold separately to Skylink QQ N GT 100R For Genie Deluxe Wall Console only e Rating of the transformer 12V DC 100mA G Diameter of DC plug 3 5mm Multi Function Wall Console Other Brands For brands other than Chamberlain Lift Master Sears Craftsman and Genie the Skylink GT 100R should be installed in parallel with the original Multi Function Wall Console Refer to Parallel Connection under Genie Deluxe Wall Console 3 OPERATION Operation Keypad Transmitter To operate the garage door opener enter the password and The factory default password is 0 0 0 Therefore to activate the Garage One receiver GT 100R with the keypad transmitter simply enter 0 0 0 1 Follow the instructions below to change the factory default password Changing Password To change a password you must have the master password which is the password that allows setting additional password Up to 3 second ary passwords can be assigned to each keypad transmitter Therefore the total number of password is 1 Master Password Programming and Operation 3 Secondary Password Opera
10. tion Only To change the master password follow the instructions below To change the password follow the instructions below Enter the current password 000 is the factory default password Press Press 0 Press Enter the new password password can be from 3 to 6 digits Press oahwonh If the keypad transmitter accepts the new password it will a long beep If it emits 3 short beeps it means the password has not been changed Start again from step 1 To assign or change secondary password follow the instructions below 1 Enter the current master password 000 is the factory default password 2 Press 3 Press the numeric key that represents the secondary password user either 1 2 or 3 4 Press 5 Enter the new secondary password password can be from 3 to 6 digits 6 Press If the keypad accepts the new secondary password it will emit a long beep If it emits 3 short beeps it means the password has not been assigned or changed Start again from step 1 To delete a secondary password follow the instructions below 1 Enter the current master password 000 is the factory default password 2 Press 3 Press the numeric key that represents the secondary password user either 1 2 or 3 4 Press 5 Press again If the secondary password is successfully deleted it will emit a long beep Otherwise start from step 1 again 3 OPERATI
11. used in conjunction with the Skylink garage door closer and any CO detector sold separately It is used to detect the CO emission inside the garage When the CO level exceeds the safety limit the alarm from the CO detector will sound which will trigger Skylink s Audio Sensor Skylink wall console will open the garage door for 10 minutes to improve air circulation Door will then be closed automatically after the CO level resumes within the safety limit 6 FCC This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful inter ference to radio communications However there is no guarantee that interference will not occur in a particu
Download Pdf Manuals
Related Search