SkyLink GM-434T User's Manual
Contents
1. If the connector is removed completely not placed on any posts it is set to 0 see diagram for examples of how to set a column to the three different positions Note A connector can be removed with the clip as shown Open the top cover Code Connectors on Sensor Note If you experience interference from a nearby system which could accidentally trigger your system please change the e code settings on the sensor and receiver The code setting on the sensor and receiver should still match after changing the code setting 7 2 ZONE CONNECTORS Each receiver can work with up to 4 different sensors to represent 4 different zones on the receiver There are 2 connectors that determine the zone number 1 2 3 and 4 These 2 connectors can be found by opening the top plastic cover near the code connectors with marking A amp B Please follow table 1 to set the zone 2 SET UP THE GARAGE DOOR MONITOR SENSOR CONT Zone Table 1 in the table means the connec tor for that position should be placed on the posts in the table means the connector for that position should be removed 3 POWER UP THE GARAGE DOOR MONITOR SENSOR After setting up all the connectors the sensor is ready to be powered up Remove the top cover on the sensor and insert the 3V lithium battery to the sensor as shown in the diagram After insert the battery to the sensor the receiver will2. visit our FAQ website at www skylinkhome com or 2 email us at support skylinkhome com CE CAPITAL PROSPECT LTD Rm 1303 13 F Block B Veristrong Ind Centre 36 AuPuiWan Street Fo Tan Hong Kong Tel 852 2602 1318 Fax 852 2602 4684 Email support skylinkhome com http www skylinkhome com P N 101A251 001 Rev 1 2005 SKYLINK GROUP
3. Garage Door Monitor Sensor Model GM 434T 1 INTRODUCTION The garage door monitor sensor is designed to monitor the status of your garage door and advise you if the door is open By placing the sensor on the door panel you will be alerted when the door is open When the garage door is open receiver will beep and flash In this package you should find a garage door monitor sensor 3V lithium battery double sided foam tape mounting accessories and a clip 4pcs 3x 18 screws 1pc 2x5 screw l oip 3V Lithium battery Garage Door Monitor Sensor Double sided foam tape Mounting plate Please follow the instructions below to set up your garage door monitor sensor properly 2 SET UP THE GARAGE DOOR MONITOR SENSOR 1 CODE CONNECTORS In order for the sensor to communicate with the receiver properly the sensor s code must match with the receiver s code Code connectors 1 to 6 can be found by opening the top cover of the sensor and the back cover of the receiver User is required to set these code connectors randomly and the code settings on the sensor and receiver must be the same Each position of the code connector can be set to or 0 position Refer to the diagram below to set the code connectors properly If the connector is placed on the top and middle posts that column is set on If the connector is placed on the middle and bottom posts that column is set on
4. l Note Mount the sensor near the top of the garage door for best results Note Ensure you straighten up the antenna on the receiver to receive the besi possible reception 5 OPERATION Nhen the garage door is open the sensor will send a signal to the eceiver It will beep and the corresponding zone red LED will flash f the sensor is set to zone 1 zone 1 red LED on the receiver will flash and the receiver will emit a continuous single beep i e beep pause beep pause etc f the sensor is set to zone 4 zone 4 red LED will flash and the receiver vill emit a con tinuous 4 beeps i e beep beep beep beep pause beep yeep beep beep pause etc 3y the number of beeps emitted by the receiver user can identify which zone Is triggered 6 BUZZER VOLUME You can select the buzzer volume by switching the volume switch to HI or LO position The buzzer can be disabled by switching to the OFF position f 7 MUTE When a sensor is triggered for a long period of time you may stop the buzzer by pressing the mute button When another signal comes again you can disable the buzzer for all currently activated sensors by pressing the mute button The receive will beep again if it receives another signal lawn with the garage door open you may Wa want to disable the buzzer for this garage door only Then you can press the Mute Fe zj button after it
5. respond to the transmitted signal depending on the orientation of the sensor positive side up Insert 3V lithium battery to the sensor If the sensor is face up in the vertical position the green LED on the receiver will glow steadily indicating the sensor is in a closed position If the sensor is face down in the horizontal position one of the red LED on the receiver will flash and the buzzer on the receiver unit will also emit beeping to indicate a door is open You can change the orientation of the sensor and vertical you should see the change in response of the receiver If the sensor and receiver are working ee properly in close proximity you can now begin to ee install the sensor onto your garage door Horizontal NOTE It is normal to hear a rattle from the sensor when tilted or rotated to another position 4 INSTALLATION A Unplug the power cord of your garage door opener WARNING before installation to ensure power is not connected Attached the sensor to the garage door with double sided foam tape if the surface of your garage door is smooth and clean enough to provide a good adhesive surface such surface can usually be found on a metal garage door Please ensure the surface is smooth and clean For wooden garage doors it is recommended to use the mounting plate and screws as well 4 INSTALLATION CONT nD Double sided Sensor foam tape Mounting plate and screws optiona
6. starts to sound If any other sensor is triggered the receiver will sound again 8 LOSS OF SIGNAL INDICATION When the battery level on the sensor drops to a certain level or the sensor is out of the operating range the receiver will show a loss of signal indication The red LED representing that zone will flash rapidly i e if Zone 1 sensor is lost the zone 1 red LED will flash rapidly For instance if you are working on your When the loss of signal indication occurs move the receiver closer to the corresponding sensor and trigger that sensor If the red LED stops flashing rapidly that means the receiver or sensor needs to be relocated If the loss of signal indication persists replace the battery of that sensor The Household Alert receiver can work with up to 4 different sensors garage door monitor sensors door window sensors water sensors indoor outdoor motion sensors etc Please visit www skylinkhome com or contact us at support skylinkhome com for more information of how to fully utilize your Garage Door Monitor 10 WARRANTY If within one year from date of purchase this product should become defective except battery due to faulty workmanship or materials it will be repaired or replaced without charge Proof of purchase and a Return Authorization are required 11 CUSTOMER SERVICE If you would like to order Skylink s products or have difficulty getting them to work please 1
Download Pdf Manuals
Related Search