Home

Sirius Satellite Radio SIR-GM1 User's Manual

image

Contents

1. sane 4 siR G m wet r NS E SIR GM1 GM CLASS 2 BUS COMPATIBLE SIRIUS SATELLITE RADIO TUNER Installation Guide SIRIUS ccor kcect Congratulations on your purchase of the SIR GM1 the GM Compatible SIRIUS Satellite Radio Tuner Your SIR GM1 is designed replace the factory XM Satellite tuner in select GM vehicles The tuner is also compatible with systems that support Satellite Radio operation but did not come with a tuner from the factory Compatibility The SIR GM1 is designed to be compatible with select headunits from 2003 2006 in select vehicles that operate on the Class 2 Bus Please consult the compatibility chart that is included with this product Compatible Headunit Types CDonly Headunits CD Cassette Headunits 6 CD changer Headunits Touch Screen Monitor Headunits Non Touch Screen Monitor Headunits Note that the units must have a BAND button to access SIRIUS audio modes In addition the SIR GM1 is compatible with most additional factory audio accessories that might be included Such as Rear Seat Audio Control Center RearSeat Entertainment DVD Monitor System Headsup display HUD Steering wheel controls Note that the SIR GM1 is not compatible with the factory satellite radio antenna that might be installed in the vehicle You must install a SIRIUS compatible antenna such as the one included with this product In addition some aftermarket Class 2 bus accesso
2. eese 21 single micro cable Connector TYPE Ls sa asas ones decedente conie as SMB Right angle FAT IDXe Tio i susu iai ii i 1 4V rms Fixed Included Cables seen T Harness Interface Cable i Factory SDAR Interface Cable T Power harness with in line noise filter Please write down your SIRIUS ID in the space provided below SIRIUS ID SIRIUS Customer Service 1 888 539 7474 Design and specifications subject to change without notice SIR GM1 Installation Guide 13 TELLI SA TE RADIO SIRIUS Satellite Radio 1221 Avenue of the Americas New York NY 10020 888 539 7474 www sirius com 2006 SIRIUS Satellite Radio Inc SIR GM1 Install Manual v05162006 SIRIUS and the SIRIUS dog logo are trademarks of Sirius Satellite Radio Inc
3. Route the cable from the antenna to the vehicle s interior by tucking it underneath the rubber molding around the rear window if possible Route the cable from the lowest point ofthe rear window into the trunk Take advantage of any existing cable channels or wiring conduits SIRIUS correct For SUVs minivans and five door vehicles bring the cable into the vehicle under the rubber molding for the tailgate and continue under the interior trim Fromthe trunk carefully route the cable to the location of the SIR GM 1 and plug the SMB connector onto the unit Sedan Coupe SUV Mini Van Caution Do not pull the wire across sharp edges that could damage it Keepthe wire away from areas where it could become tangled in the driver s and passenger s feet Keepthe antenna wire away from extreme heat like exhaust systems Avoid placing the cable near any moving parts Wiring and Cable Connections A SIRIUS CONNECL jj SIRIUS SATELLITE RADIO SIR GM1 GM COMPATIBLE SIRIUS SATELLITE RADIO TUNER HEADUNIT 0 A Antenna Input Connect the right angle SMB connector from the antenna Push firmly to attach Connect to only approved SIRIUS Satellite Radio antennas DO NOT connect to the factory satellite radio antenna if installed B Headunit Connector Connection to either the Factory SDAR interface cable or T Harness cable depending
4. product failure USE CAUTION IF YOU NEED TO DISCONNECT THE BATTERY TERMINAL Please consult the vehicle s owner s manual or a service technician prior to removing the battery positive or ground connection as it may cause damage to the vehicle s electrical system or require reprogramming of the vehicle s computer controlled devices SIRIUS correct COMPATIBILITY The way the SIR GM1 is installed and used in your vehicle will vary depending on several factors including the make model and year of the vehicle as well as the factory installed options Please refer to the information below for information on the proper method of SIR GM1 installation If your vehicle is pre wired for satellite radio then you should install the SIR GM1 in the factory satellite radio tuner location using the existing wiring and the factory harness adapter Please refer to the factory service manuals for appropriate installation instructions If your vehicle is not pre wired for satellite radio but it is compatible with the SIR GM1 then you must use the provided T harness to connect to the back of your factory headunit Installation It is recommended that prior to starting the installation you thoroughly read this manual and follow the guidelines listed below Some installations may use the factory satellite radio tuner location If you are using this location please follow the factory instructions for installing the t
5. activate SIR GM1 before you can start to receive the SIRIUS Satellite Radio broadcast 1 Make sure that the SIR GM1 is properly connected and that its antenna is oriented to receive the SIRIUS satellite signal 2 Turn on the headunit 3 Use your factory radio s controls to select satellite radio as the source Pressing the BAND button will change sources to SR1 or SR2 Note some headunits will display XM1 or XM2 when in SIRIUS mode 4 If this is the first time the unit is connected and receiving satellite signal the display may read UPDATING until the SIR GM1 channel update is completed This is where the latest channel line up is updated on the SIRIUS Receiver NOTE Don t push any buttons or perform any operations until updating has been completed Once updated and the SIRIUS channels are received you will be tuned to SIRIUS Satellite Radio s Preview Channel Channel 184 You should be able to hear the SIRIUS Preview channel s Audio 5 Find the SIRIUS ID SID of your unit The SID can be found on a sticker on the bottom of the SIR GM1 or by tuning to channel 255 Press the display button DISP on most units some use INFO to select either artist name or song title Both fields will display the 12 digit SID 6 Write down the 12 digit SID in the location provided on the next page for future reference 7 Contact SIRIUS on the Internet https activate siriusradio com Follow the prompts to activate your sub
6. e cable through the grove Peal off the adhesive tape Note that the SIR GM1 is not compatible with the factory satellite radio antenna that might be installed in the vehicle You must install a SIRIUS compatible antenna such as the one included with this product To attach the cover tail 1 Once you have determined the proper mounting location see next section clean the area with the supplied alcohol swab 2 Connect the cover tail to the antenna cable making sure that the strain relief seats into the cover tail groove Route the cable through the wire channel in the cover tail 3 Remove the remaining protective tape from the adhesive carefully position the antenna with cover tail and apply pressure to secure to the vehicle Optimum Antenna Mounting Locations The optimum location to mount the antenna is on the roof of the vehicle It is important to avoid any obstruction that will block satellite signal like a roof rack For convertible vehicles install the antenna on the trunk lid Place the antenna on a metal surface of your vehicle at least 12 x 12 and at least 6 from a window Use the antenna cover tail as a guide for the proper distance The antenna s powerful magnet will secure it to the metal surface The adhesive that is attached to the antenna cover tail will secure the cable to the vehicle Before routing the antenna cable confirm that the antenna is mounted in a good location
7. g Locations eene 7 Wiring and Cable Connections eeeeeseeeeeeeeeee enne ennt nennt nnns 8 System Connection Examples esses nana ananasas 10 Activating Your SIRIUS Subscription ueeeeeeeeeeeeereeeeeneeen 12 Specifications e 13 Package Contents A O mum SIRIUS CONNECL SIRIUS SATELLITE RADIO SIR GM1 GM COMPATIBLE SIRIUS SATELLITE RADIO TUNER A SIR GM1 Tuner B Mini Magnetic Antenna C Antenna Cable Cover Tail D Alcohol Swab E F G H Factory SDAR Interface Cable T Harness Interface Cable Power Harness with Filter Mounting Screws Qty 6 SIR GM1 Installation Guide 3 A WARNING This symbol means important instructions Failure to heed them can result in serious injury or death DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE Any function that requires your prolonged attention should only be performed after coming to a complete stop Always stop the vehicle in a safe location before performing these functions Failure to do so may result in an accident DO NOT OPEN DISASSEMBLE OR ALTER THE UNIT IN ANY WAY Doing so may result in fire electric sh
8. ill occur while using the SIR GM1 SIR GM1 Installation Guide 9 System Connection Examples System 1 For vehicles pre wired for satellite radio Factory wiring harness Remove the Factory XM Tuner and connect the SDAR Interface Cable SIRIUS CONNECL SIR GM1 GM COMPATIBLE SIRIUS SATELLITE RADIO TUNER Factory SDAR Interface Cable i DO NOT cut or extend the supplied harness Doing so can cause operation or noise issues NOTE If installing into a Cadillac CTS a slight modification of the Factory SDAR Interface Cable is required Please see the attached technical sheet for details 10 SIR GM1 Installation Guide System 2 For vehicles not wired for satellite radio Factory bus connector removed from headunit SIRIUS CONNECL SIR GM1 M COMPATIBLE DO NOT cut or extend the supplied SIRIUS SATELLITE RADIO TUNER harness Doing so can cause operation or noise issues T Harness Interface Cable Factory bus connector Connect YELLOW wire to the Battery _ Positive or other good B source Power Harness with Filter Connect Black wire to a solid Chassis Ground as short as possible SIR GM1 Installation Guide 11 Activating Your SIRIUS Subscription You must
9. ock or product damage DO NOT INSERT ANY OBJECTS INTO THE UNIT Doing so may result in fire electric shock or product damage USE THE CORRECT AMPERE RATING WHEN REPLACING FUSE Failure to do so may result in fire electric shock or product damage MAKE THE CORRECT CONNECTIONS Failure to make proper connections may result in fire or product damage DO NOT SPLICE INTO A ELECTRICAL CABLES Never cut away cable insulation to supply power to other equipment Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock DO NOT INSTALL IN LOCATIONS THAT MIGHT HINDER VEHICLE OPERATION Doing so may obstruct vision or hamper movement which can result in a serious accident DO NOT INSTALL THE UNIT TO HIGH LEVELS OF HUMIDITY MOISTURE OR DUST Doing so can result in electric shock or product failure FCC Warning This equipment may generate or use radio frequency energy Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in this User Guide The user could lose the authority to operate this equipment if an unauthorized change or modification is made Note This equipment has been tested and found to comply with Part 15 of the FCC Rules These rules are designed to provide reasonable protection against harmful interference This equipment may cause harmful interference to radio communications if it is not installed and
10. on system type Factory SDAR Interface Cable Use this cable if you are replacing the factory XM satellite tuner T Harness Interface If your vehicle does not have a factory XM satellite tuner installed use the T Harness and supplied power harness with noise filter Note 1 DO NOT cut or extend the supplied harnesses Doing so can cause operation or noise issues Note 2 It is not possible to have both the factory XM tuner and the SIR GM1 installed at the same time 8 SIR GM1 Installation Guide Antenna 21 cable Mount on Roof of Vehicle Right angle SMB Connector SIRIUS Headunit Side O Factory bus connector ccor ect SIR GM1 Factory GM Class 2 Radio GM COMPATIBLE SIRIUS SATELLITE RADIO TUNER SIR GM1 T Harness Interface Cable Factory bus connector Vehicle Side 1 AMP ATC Fuse aded EIS Connect YELLOW wire to the Battery Positive or other good B source L 1 AMP Fuse located a inside noise filter Connect Black wire to a solid Chassis Ground as short as possible NOTE If your vehicle is equipped with a factory satellite radio tuner and you are using the included T harness interface cable for installation you must disconnect the factory satellite radio tuner at the tuner box Otherwise operational errors w
11. ries may cause performance or interference problems with the SIR GM1 Features The SIR GM 1 is designed to emulate many of the factory SDAR Satellite Digital Audio Radio commands found in your vehicle Channel Tune Up and Down FastTune Up and Down Category Search Up and Down Category Tune Tune within a category 12presets 6 for each band Preset Scan UP Note about features listed Each GM radio type operates differently so consult the vehicle owners manual for proper operation methods Headunit Display Capability When the SIR GM1 is installed it has the capability to show the following information on the headunit display Channel Number Channel Name Category Name Artist Name Song Title Name Number of characters displayed varies by headunit type 8 16 Characters Text Scrolling and or Paging is not supported with the SIR GM Note Some GM headunits will display XM1 or XM2 as the display source This information is hard coded in the headunit design and can not be changed Table of Contents Package Contents csecccseeeeessseeeenseeeeeenneeeesnaeeseneaeseasaneeessecaeseesaeseasseaeeaseaneeees 3 Warnings and Caution occi i ni inae inni i i i i 4 DEEP cR 6 Mounting tlie TUNET saskes a eet eren eset inn ehe ree ade i a 6 Installing the Antenna eeeeeeeeeeeeeeeeneeneenn eene nnn ennemi nnns nennt 6 Optimum Antenna Mountin
12. scription You can also call SIRIUS toll free at 1 888 539 SIRIUS 1 888 539 7474 to activate your tuner Note You will not be able to tune to any other channels until you activate your SIRIUS subscription Basic Operation After the unit is activated please follow the steps below to insure proper operation of the unit 1 Power off the headunit close all doors for 1 minute 2 Open the door and either start the car orturn on the ACC 3 Cycle through the BANDS to select SR1 or XM1 4 Select each preset one time the headunit may have retained presets from the XM radio This will change all the presets to the SIRIUS default channels 5 Press BAND to select SR2 or XM2 and repeat step 4 above 6 You can now tune and set up your presets as you wish For specific headunit functions please consult your GM headunit owner s manual for proper operation instructions for using satellite radio products Note When reactivating a deactivated receiver the headunit MAY show the UPDATING message continuously Channel tune UP or Down to clear the message Specifications Operational Frequencies Satellite oe Be SS eB eee emer 2322 293 2330 207 MHz TORR SEMA mc i ii i ii i 2326 250MHz Power Requirements eese eee 11 16 Volts DC Chassis Size 126 75mm x 125 75mm x 34 75mm WxHxD Antenna TYPO eem Mini Magnetic Antenna Cable Length
13. uner in your vehicle If you are not using this location please read the following installation guidelines Consider the mounting location carefully You should make sure that you avoid the following Any location where the tuner is exposed to moisture Any location where the unit is exposed to extreme heat Any location that would interfere with moving parts on the vehicle or hamper driving Mounting the SIR GM1 Tuner Be sure that you find a location that is flat and has clearance above the unit to prevent any damage as well as allow for ventilation Do not install the tuner under the carpet or in a small enclosed area without proper ventilation Doing so can result in damage to the tuner or the vehicle Use the supplied screws to securely fasten the unit Caution If you are attaching the unit directly to the vehicle s chassis be sure that you check to make sure the area behind the unit is free from moving parts fuel or break lines wire harnesses or any other items which may get damaged by drilling a mounting hole or using the supplied screws Installing the Antenna The antenna includes a 6 1 2 cable cover tail which covers the exposed antenna cable and keeps it attached securely to vehicle roof The tail also helps position the antenna the proper distance from the window sunroof or rear hatch Antenna Bottom Cable Cover Tail Connect the cable cover tail to the antenna cable insert th
14. used in accordance with these instructions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of more of the following measures Relocate the receiving antenna Consult the dealer or an experienced technician for help A CAUTION This symbol means important instructions Failure to heed them can result in injury or material property damage HALT USE IMMEDIATELY IF A PROBLEM APPEARS Failure to do so may cause personal injury or damage to the product Return the unit to your authorized retailer or nearest service center for repairing INSTALL THE WIRING SO THAT IT IS NOT CRIMPED OR PINCHED BY SCREWS OR SHARP METAL EDGES Route the cables away from moving parts or sharp pointed edges This will prevent crimping and damage to the wiring If the wiring must pass through a metal hole be sure to use a rubber grommet to prevent the wire s insulation from being cut by the metal edge of the hole USE THE SPECIFIED ACCESSORY PARTS AND INSTALL THE PRODUCT SECURELY Be sure to use only the specified accessory parts Use of non specified parts may damage this unit internally or may not securely install the unit in place This may cause parts to become loose resulting in hazards or

Download Pdf Manuals

image

Related Search

Related Contents

Buffalo TeraStation III, 4.0TB  Z30829 A B - Lidl Service Website  フットポンプ S(SG規格商品)  Tutorials  poLYpErF® Safe et ppS® Quick poLYpErF® Safe y ppS® Quick    Scarica Libretto Tecnico  SolidscreenTM II Strip  Course Information Instructor Information Introduction to Computing  埼玉東部消防組合工事検査要綱  

Copyright © All rights reserved.
Failed to retrieve file