SIIG CYBER 2S1P User's Manual
Contents
1. a request to SIG RMA If the product is determined to be defective an RMA number willbe issued SIIG RMA department can also be reached at 510 413 5333 Step 2 After obtaining an RMA number ship the product e Properly pack the product for shipping All software cable s and any other accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e Youare responsible for the cost of shipping the product to SIIG at the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 RMA e SIIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer 11 About SIIG Inc Founded in 1985 SIIG Inc is a leading computer upgrade manufacturer of I O connectivity products including PCI amp ISA serial and parallel ports USB Serial ATA amp UltraATA controllers FireWire 1394a b Networking Sound Cards and other accessories SIIG is the premier one stop source of upgrades SIG products offer comprehensive user manuals many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall ease of installation and compatibility of our2. products as well as one of the lowest defective return rates in the industry SIIG products can be found incomputer retail stores mail order catalogs and e commerce sites inthe Americas and the UK as wellas through major distributors system integrators and VARs PRODUCT NAME Cyber 2S1P PCI FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCESTATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SIG Inc 6078 Stewart Ave Fremont CA 94538 3152 Cyber 2S1P PCTis a trademark of SIG Inc SIG and SIIG logo are registered trademarks of SIIG Inc Microsoft and Windows are registered trademarks of Microsoft Corporation Pentium is a registered trademark of Intel Corporation Other names used in publication are for identification only and may be trademarks of theirrespective companies March 2005 Copyright 2005 by SIG Inc All rights reserved
3. well seated Replace the slot bracket s holding screw to secure the card Replace the computer cover and reconnect the power cord Driver Installation This section provides information on how to install the Cyber 2S1P PCI drivers Windows 95 1 At the Update Device Driver Wizard click Next Insert the driver CD and click Other Locations Type in D 9x click OK then Finish Change D to match your CD ROM drive letter From the Insert Disk window click OK When the Copying Files dialog box appears type in D 9x then click OK Repeat steps 1 3 Restart Windows to complete the installation Windows 98 98SE 1 Atthe Add New Hardware Wizard click Next 2 Select Search for the best driver for your device Recommended then click Next 3 Insert the driver CD check Specify a location uncheck the other boxes type in D 9x click Next Change D to match your CD ROM drive letter Click Next then Finish 5 Repeat steps 1 4 6 Restart Windows to complete the installation Windows ME 1 Atthe Add New Hardware Wizard select Specify the location of the driver Advanced click Next 2 Insert the driver CD check Specify a location uncheck the other box type in D Me then click Next Change D to match your CD ROM drive letter 3 Click Next and Finish 4 Repeat steps 1 3 5 Restart Windows to complete the installation To Verify Windows 95 98 98SE ME Installation 1 From the main de
4. Cyber 2S1P PCI lt gt o Quick Installation Guide Introducing the Cyber 2S1P PCI The Cyber 251P PCI high speed serial I O card provides two 9 pin serial ports and one parallel port Features and Benefits Conforms to PCI v2 2 Plug and Play Full support for Windows based software Reduces CPU load and improves system performance dramatically IRQ sharing feature reduces IRQ conflicts High speed serial port 9 pin works with 56K V 90 external modems ISDN terminal adapters PDAs digital cameras label printers and other serial port devices Built in FIFO buffers dramatically increase data transmit receive speed especially under Windows multitasking environment Each serial port can be configured for either 5v or 12v output for serial devices that require power TEEE 1284 compliant SPP EPP ECP parallel port System Requirements Pentium or equivalent computer with an available PCI slot Windows 95 98 98SE ME NT 4 0 2000 XP Server 2003 04 0345B 1 Package Contents Cyber 251P PCI board e Connector bracket w 9 pin serial port e DriverCD Quick Installation Guide Layout JP1 Serial Port 2 S1 S2 Pin 1 Serial Port 1 S1 Parallel Port JP2 S2 Figure 1 Layout Jumper Settings JP1 JP2 Open 0 volts default Short 1 2 5V Short 2 3 12V Note Mostserial devices donotrequire additional power through the serial port Refer to your serial device s manual for more information The ju
5. ange D to match your CD ROM drive letter 5 Click Next and Finish 6 Repeat steps 1 5 two more times 7 Restart Windows to complete the installation Windows XP 1 Atthe Found New Hardware Wizard choose Install from a list or specific location Advanced then click Next 2 Insert the driver CD check Include this location in the search uncheck the other check box type in D XP and click Next Change D to match your CD ROM drive letter 3 If the Hardware Installation window pops up click Continue Anyway then Finish Our driver has been tested for stability and compatibility 4 Repeat steps 1 3 three more times 5 Restart Windows to complete the installation Windows Server 2003 1 Atthe Found New Hardware Wizard choose Install from a list or specific location Advanced then click Next 2 Insert the driver CD check Include this location in the search uncheck the other check box type in D 2003 and click Next Change D to match your CD ROM drive letter 3 If the Hardware Installation window pops up click Continue Anyway then Finish Our driver has been tested for stability and compatibility 4 Repeat steps 1 3 three more times 5 Restart Windows to complete the installation To Verify Windows 2000 XP Server 2003 Installation 1 Rightclick My Computer click Manage then select Device Manager 2 Double click Ports COM amp LPT two CyberSerial PCI 16Cxxx and one CyberParallel PCI sh
6. l PCI Click Settings tab check Enable use of I O location 278h Click OK click OK again to close Device Manager and click Yes to restart Windows to save the changes Windows 2000 XP Server 2003 1 From the Device Manager window double click Ports COM amp LPT then double click CyberParallel PCl Click Port Settings tab At the LPT Port Number box click the down arrow and select an LPT port that is not in use Click OK then close Device Manager to save the changes Blank Page Technical Support and Warranty QUESTIONS SIIG s Online Support has answers Simply visit our website at www siig com and click on Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away You can also submit questions online and one of our technical support analysts will promptly respond A lifetime manufacturer warranty supplied with this product is offered by SIIG Inc Please see SIIG website for more warranty details If you should happen to encounter any problems with this product please follow the procedures below If it is within the store s return policy period please return the product to the store where you purchased from If your purchase has passed the store s return policy period please follow these steps to have the product repaired or replaced Step 1 Submit your RMA request Go to www siig com click Support then RMA to submit
7. mper can be removed if the ports do not require power Serial Port 2 Connection Figure 2 Connecting the ribbon cable Hardware Installation General instructions for installing the card are provided below since the design of computer cases and motherboards vary Refer to your computer s reference manual for further information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer s case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges 1 Turn OFF the power to your computer and any other connected peripheral devices 2 Unplug the power cord from the back of the computer 3 Remove your computer s cover 4 Remove the slot bracket from an available PCI slot Change JP1 JP2 jumper settings to the desired voltage only if your serial device s needs additional power from the serial port However most serial devices do not require additional power For more information see Figure 1 on page 2 Skip this step if power is not required If you need the second serial port connect the 9 pin ribbon cable connector now See Figure 2 on page 3 for more details Skip this step if you only need one serial port To install the card carefully align the card s bus connector with the selected PCI slot on the motherboard Push the board down firmly but gently until it is
8. ould be displayed 3 Double click Multifunction adapters SIIG CyberPro 2S1P PCI board should be displayed Changing COM Port Address Some serial devices need a specific COM port in order to work If your serial device works properly do not change this setting Windows 95 98 98SE ME 1 From the Device Manager window double click Ports COM amp LPT then double click the CyberSerial PCI serial port you want to change 2 Click Settings tab at the Port Name box click the down arrow and select a COM address that is not currently in use 3 Click OK then click OK again to close Device Manager to save the changes Follow steps 1 3 again to change the second serial port if needed Windows 2000 XP Server 2003 1 From the Device Manager window double click Ports COM amp LPT then double click the CyberSerial PCI serial port you want to change Click Settings tab and click Advanced Click the down arrow that is next to the COM Port number box and select a COM port that is not in use Click OK Click OK then close Device Manager to save the changes Follow steps 1 4 again to change the second serial port if needed Changing Parallel Port Address LPT Some parallel devices need a specific parallel port in order to work If your parallel device works properly do not change this setting Windows 95 98 98SE ME 1 From the Device Manager window double click Ports COM amp LPT then doubleclick CyberParalle
9. sktop right click My Computer click Properties then click Device Manager 2 Double click Ports COM amp LPT Printer Port and CyberParallel PCI should be displayed one time and CyberSerial PCI 16Cxxx should be displayed two times 3 Double click Multi function adapters SIIG CyberPro 2S1P PCI board should be displayed Windows NT 4 0 a OY DT E 9 From the desktop click Start then Run Insert the driver CD type in D NT4 Install_Serial exe then click OK Change D to match your CD ROM drive letter Click Next when the Welcome window appears Choose Install then click Next Click Yes then click Exit From the desktop click Start then Run Type in D NT4 Install_Parallel exe then click OK Change D to match your CD ROM drive letter Repeat steps 3 5 Click Yes to restart Windows to complete the installation To Verify Windows NT 4 0 Installation 1 Click Start Settings Control Panel double click Ports device icon 2 Two new COM ports will be assigned when successfully installed 3 Click Start Programs Administrative Tools Windows NT Diagnostics Click Resources tab SIIGpar and SIIGser should be displayed Windows 2000 1 At the Found New Hardware Wizard click Next 2 Select Search for a suitable driver for my device recommended and click Next 3 Select Specify a location uncheck the other boxes and click Next 4 Insert the driver CD type in D 2000 then click OK Ch
Download Pdf Manuals
Related Search