SIIG 04-0202A User's Manual
Contents
1. e This quick installation guide Hardware Installation General instructions for installing the card are provided below since the design of computer cases and motherboards vary Refer to your computer s reference manual for further information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer s case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges 1 Turn OFF the power to your computer and any other connected peripheral devices Unplug the computer s power cord 2 Remove your computer s cover and install the card in an available PCI slot 3 Push the board down firmly but gently until it is well seated 4 Secure the card and replace the cover Software Installation This section provides information on how to install the Low Profile PCI I O s drivers for the following operating systems Windows 95 98 98 SE ME Windows NT 4 0 Windows 2000 DOS Windows 3 1x Windows 95 1 At the Add New Hardware Wizard windows click Next 2 Insert the Driver Installation diskette in the floppy drive and click Other Locations Type in a Win95 click OK then Finish 3 From the Insert Disk window click OK When the Copying Files dialog box appears type in a Win95 then click OK 4 Remove the diskette and select Yes to restart the computer for the setup to take ef2. on the accompanying RMA form SIIG will refuse to accept any shipping package and will not be responsible fora product returned without an RMA number posted on the outside of the shipping carton Step 3 Ship the Product You are responsible for the cost of shipping back to SIIG at the following address SHG Inc RMA 6078 Stewart Ave Fremont CA 94538 SIIG will ship the repaired or replaced product via UPS Ground or US Mail at no cost to you 7 PRODUCT NAME MODEL NUMBER Low Profile PCI I O LP04xx FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference ina residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a part
3. Low Profile PCI I O Quick Installation Guide Introducing the Low Profile PCI I O The Low Profile PCI I O conforms to the new PCI card form factor standard made for space constrained system designs Since this installation guide is written for both Low Profile PCI 1S and Low Profile PCI 1P boards some features on this installation guide might not be present on the model you bought Please only refer to the features that apply to your board Features and Benefits e Conforms to PCI v2 2 Plug and Play e Full support for DOS and Windows based software e IRQ sharing feature eliminates IRQ conflicts Serial interface e High speed 16550 UART serial port 9 pin supports baud rates up to 920Kbps Works with various types of serial devices e Built in 16 byte FIFO buffers dramatically increase data transmit receive speed Parallel interface e Conforms to IEEE 1284 1994 parallel port standard e High speed parallel port supports various types of parallel port devices e Supports EPP ECP PIO mode Bi directional Parallel Port BPP and Standard Parallel Port GPP modes Dimensions e PCB 119 91 mm L x 64 41 mm H e Bracket 18 42 mm W x 79 20 mm H System Requirements e Pentium or equivalent computer with an available 32 bit PCI slot e DOS Windows 3 1x Windows 95 98 98 SE ME NT 4 0 2000 04 0202A 1 Package Contents e One Low Profile PCI I O board e One Driver Installation diskette e One 5 year warranty card
4. fect Windows 98 98 SE 1 At the Add New Hardware Wizard windows click Next 2 Select Search for the best driver for your devices Recommend then click Next 3 Select Specify a location insert the Driver Installation diskette and type in a Win98 then clickNext 4 Click Next then Finish 5 Remove the diskette and click Yes to restart your system Windows ME 1 At the Add New Hardware Wizard screen choose Specify the location of the driver Advanced then click Next 2 Check Specify a location insert the Driver Installation diskette into your floppy drive type in A Win98 then click Next 3 Click Next and Finish to complete driver installation 4 Remove the driver diskette and click Yes to restart Windows To verify successful installation in Windows 95 98 98 SE ME 1 From the main desktop double click My Computer Control Panel System then click Device Manager 2 Double click Ports COM amp LPT and new Cyber PCI ports should be displayed Also double click SIIG Cyber PCI option and SHG PCI Board should be displayed The board is ready to connect new devices Windows NT 4 0 1 From the desktop click Start then Run 2 Insert the Driver Installation diskette type in A NT4 setup then click OK 3 Click Next when the Welcome window appears 4 From Choose Destination Location window click Next 5 Remove the Driver Installation diskette select Yes to restart Windows and click Fi
5. icular installation If this equipment does cause harmful interference to radio and television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio or TV technician for help Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SIG Inc 6078 Stewart Ave Fremont CA 94538 3152 SIG and SHG logo are registered trademarks of SIIG Inc Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation Pentium is a registered trademark of Intel Corporation Other names used in publication are for identification only and may be trademarks of their respective companies November 2000 Copyright 2000 by SHG Inc All rights reserved
6. in edit autoexec bat then press lt Enter gt 3 Add C CB20XPC exe at the bottom of the autoexec bat file 4 Go to File save the changes and exit 5 Remove the diskette and restart the system for the new setup to take effect Troubleshooting Problem I am installing a parallel port s and my system freezes up when Windows tries to install the driver for my printer port Solution Enter your system bios set the onboard parallel port I O address to 278h save and exit In certain systems the address 278h is reserved for ISA boards So when the PCI parallel port tries to capture this address your system gets confused and freezes up Problem I am installing serial port s and these ports show up without COM portassignment or they show up as COM5 and COM6 instead of conventional COM3 and COM4 Solution Enter your system bios under Peripherals Configuration set the first onboard serial port to 03F8 IRQ 4 instead of AUTO Set the second onboard serial port to 02F8 IRQ3 instead of AUTO if applicable Also under PnP or PCI Configuration turn Off or disable PnP OS Problem I have an Intel Celeron system and when I install a serial port it gets assigned to COM5 or above Myserial device only works from COM1 to COM4 Solution Please visit our web site at WWW SIIG COM go to Driver Update page and download an appropriate driver for your Intel Celeron system For more troubleshooting tips and driver updates please visit o
7. nish To verify successful installation in Windows NT 4 0 1 Go to Start Setting Control Panel double click SIIG Cyber PCI 20X device icon 2 New COM port address and LPT number will be assigned for the ports when successfully installed The board is ready to connect devices Note If you plan to connect a parallel device other than a printer to the parallel port such as zip drive or scanner please follow the next section to change the port s I O address to support these devices To change the I O address in Windows NT 4 0 1 Double click Start Settings Control Panel then SIIG Cyber PCI 20X device icon 2 Highlight the LPT or COM address and click Settings 3 Select or type in an I O address supported by the device you would like to configure and click OK Make sure the selected I O address does not conflict with other device in your system 4 Select Restart Now for the new setup to take effect Windows 2000 Windows 2000 will automatically detect and install the correct driver for Low Profile PCI 1S and Low Profile PCI 1P To verify successful installation in Windows 2000 1 Double click My Computer Control Panel System Hardware and click Device Manager 2 Click on the plus sign in front of Ports Com amp LPT 3 New Cyber port s should be listed DOS Windows 3 1x 1 Insert the Driver Installation diskette from the C prompt type in copy a dos then press lt Enter gt 2 Type
8. ur web site at WWW SIIG COM and go to Online Support or Driver Update Technical Support QUESTIONS SIIG s Online Support has the answers Simply visit our website at www siig comand click on ONLINE SUPPORT Our online support database is updated daily with new drivers and solutions The answers to your problems could be just a few clicks away Return Merchandise Authorization RMA SIG warrants to the original buyer of the product that the hardware is free of defects in materials and workmanship fora period of one two or five years from the date of purchase If your product fails to be in good working order during the warranty period you may return it to SUG for repair or replacement at SIIG s option To return the product you need to follow these steps Step 1 Contact SIIG s RMA Department To obtain an RMA number SIG s RMA Department can be reached by phone at 510 413 5333 or fax at 510 657 5962 or email at service siig com In order to issue an RMA number the product serial number is required This number can be found on the side of the box and on the back of the product Step 2 Complete the RMA form e Filloutyour Return Merchandise Authorization RMA form and include it in the package with the product e Properly pack the product for shipping All software cable s and other accessories that came with the original package must be included e Clearly write your RMA number onthe top ofthe returned package and
Download Pdf Manuals
Related Search