Sierra Monitor Corporation PSE530 User's Manual
Contents
1. Withstand pressure 1 5MPa Fluid Air Non corrosive gases Incombustible gases Power supply 12 to 24VDC ripple p p 10 or less Protection against inverse connection Current consumption 15mA or less Voltage 1 to 5V2 F S or less Rated pressure range Linearity 1 F S or less Output impedance Approx 1kQ Analog output Voltage output 1 F S or less Repeatability Effect form power supply 1 F S or less with standard of analog output at 18V in the range of 12 to 24VDC 2 F S or less 25C reference Enclosure IP40 Temperature Characteristic or may fail thereby resulting in malfunction e Do not drop it bring it into collision with other objects or apply excessive shock 980m s or more e Do not pull the lead wire with force nor lift the main unit by Cable for sensor have connector cover in order to prevent fall of female connector Paying attention for connector cover direction install on the sensor rotate clockwise and lock it To remove cable for sensor rotate the connector cover anti Ambiebt temperature Operation 0 to 50 C Storage 10 to 70 C No condensation No freezing Withstand voltage 1000VAC 50 60Hz 1minute Between lead block and case Insulation resistance 5MQ or more 500VDC Between lead block and case AWARNING Do not disassemble remodel including change of printed circuit board or repair2. Thank you for purchasing the SMC PSE530 Series Pressure Sensor Please read this manual carefully before operating pressure sensor and understand pressure sensor its capabilities and limitations Please keep this manual handy for future reference SMC Corporation URL http www smcworld com SAFETY The Pressure Sensor and this manual contain essential information for the protection of users and others from possible injury and property damage and to ensure correct handling Please check that you fully understand the definition of the following messages signs before going on to read the text and always follow the instructions IMPORTANT MESSAGES Read this manual and follow its instructions Signal words such as WARNING and NOTE will be followed by important safety information that must be carefully reviewed Indicates a potentially hazardous situation AWARNING which could result in death or serious injury if you do not follow instructions Installation addendum information Attaching the connector to the lead wire Sensor wire is stripped as shown iN Connector the right figure cover 20mm or more The Insulation of the corresponding A color shown in the following table is SS put into the pin of the number stamped insiiati n on the connector for sensor connection to the bottom Color of Insulation Brown DC N C Blue DC Black IN 1 to 5VDC It checks t
3. holding the lead wire Pulling strength less than 23N e Do not insert wire nor other article into the pressure port e Perform wiring and cable correctly clockwise relese lock and remove connector cover After removing connector cover pick with female connector with fingers and pull out Environment 10 to 500Hz smaller one 1 5mm or 98m s double amplitude 2 hours each in direction of X Y and Z 980m s 3times each in directions of X Y and Z respectively Vibration proof Impact proof An injury or failure can result e Do not perform wire or cable while power is on Standard CE MARKING Do not wire with the same circuit of power line or high voltage Cable Halogen free heavy insulation cable 2 7 0 15mm 3wire 3m Do not operate beyond specification range line l a Piping Speci gation Fire malfunction or sensor damage can result Connect Terminal FG to the ground when using a switching regulator obtained on the commercial market Model No M5 R06 R07 Do not operate in a combustible gas or explosive e Keeping from water and dust set an air tube to the safety Port size M5X0 8 6 Reducer 1 4inch Reducer gas atmosphere Fire or an explosion can result This pressure sensor is not an explosion proof type area Unlock Sensor pressure sensing part Silicon O ring NBR Material Body SUS303 Body PBT With cable 3m Weight Excluding cable 7g 3 8g
4. e square groove in the housing until connector clicks When disconnecting the connector push down the lever by thumb to disengage the lever claw from the square groove Then pull the connector straight out PSE200 Series PSE300 Series Connector for Sensor Lead Wire Example of Internal Circuit and Wiring Output Specification Voltage output Brown DC 1 to 5V K Output impedance Wy Black OUT Approx 1kO Q Analog output 3 1 12 to 24V DC Blue DC ABlue How to connect the cable for sensor Optional Pick with fingers the hemale connector of cable for sensor Insert it paying attention of connector direction Sensor Male connector Female connector a Outline with Dimensions in mm PSE53C M5 M5 x 0 8 29 4 Pressure port 27 2 5 5 5 PSE53L R06 R07 3 45 5 z 34 T 43 3 i Pressure port lt i aN _ N ii 5 a t i m ey a V i Model No Applicable port size D PSE530 R06 6mm PSE530 R07 1 4inch When connect cable for sensor 9 8 10 4 2 7 Specification Model No PSE533 101 to 101kPa PSE532 0 to 101kPa 500kPa PSE531 0 to 101kPa PSE530 Rated pressure range 0 to 101MPa
5. hat the above mentioned preparation work has been performed correctly and A part temporary connection A part center is straightly pushed in by tools such as pliers Re use cannot be performed once it connects the connector for sensor connection completely A sensor connector cannot be taken apart for reuse once it is crimped If the wire arrangement is incorrect or if the wire insertion fails use a new sensor connector When connecting the connector to PSE200 PSE300 series please use X the connector for Sensor Lead Wire ZS 28 C or con as below Model No c Sumitomo 3M 37104 3101 O00FL Tyco Electronics AMP 3 1473562 4 OMRON XN2A 1430 Please contact with each connector maker about con catalogue OPERATOR This operation manual has been written for those who have knowledge of machinery and apparatus that use pneumatic equipment and have full knowledge of assembly operation and maintenance of such equipment Please read this operation manual carefully and understand it before assembling operating or providing maintenance service to the pressure sensor NOTE Follow the instructions given below when handling your pressure sensor Otherwise the sensor may be damaged Connector Connector Connecting Disconnecting When connecting the connector insert it straight onto the pin holding the lever and connector body between fingers and lock the connector by pushing the lever claw into th
Download Pdf Manuals
Related Search