Shure WH30XLR User's Manual
Contents
1. 20 am E z 10 _ LU 2 5 n o 2 10 gt oy lt Or 20 i J 5 1 cm 0 4 in gt SEE cS 7 61 cm 24 in 20 50 100 200 500 1 000 2 000 5 000 10 000 20 000 FREQUENCY IN Hz FIGURE 6 WH30 TYPICAL FREQUENCY RESPONSE FIGURE 7 WH30 TYPICAL POLAR PATTERNS 1 51 5u WIRING DIAGRAMS A zo MODEL WH30TQG CARTRIDGE 7 77 Tl RED to drain DC bias TA4F CONNECTOR 7 e T BLACK to source audio ELEMENT D SHIELD bess J CARTRIDGE MODEL WH30XLR MIC oy pe ELEMENT Ul pri 1 XLR CONNECTOR X BLACK to source audio FILTER RED to drain DC bias Y vL SHIELD PREAMP V FIGURE 8 WIRING DIAGRAMS Trademark Notices The stylized Shure logo the word Shure are registered trademarks of Shure Incorporated in the United States Teflon is a registered trademark of duPont de Nemours and Company in the United States Croakies is a registered trademark of Life Link International Inc SHURE Incorporated Web Address http www shure com 5800 W Touhy Avenue Niles IL 60714 4608 U S A Phone 800 257 4873 Fax 847 62. guide for your wireless transmitter and receiver system for ad justing gain and other parameters WIRED APPLICATIONS Connect the output of the RPM420 preamplifier to an input channel of a mixing or recording console Most consoles will provide phantom power to the RMP420 preamplifier If phantom power is unavailable use a separate phantom power supply such as the Shure PS1A WASHING THE ELASTIC HEADBAND When necessary remove and wash the elastic headband according to these steps 1 Remove the microphone cable retainer from the wireframe 2 Slide the elastic headband off the wireframe 3 Wash the headband mild soapy water and rinse it in clean water 4 Allow the headband to air dry thoroughly 5 Slide the headband around the wireframe to its original position Reattach the cable with the plastic retainer WASHING THE FOAM WINDSCREEN The foam windscreen protects the WH30 s microphone element from dirt and moisture When necessary it can be removed and cleaned in a mild soapy water solution mportant Never clean the windscreen with any liquid solution without first removing the windscreen from the microphone boom 1 Hold the windscreen loosely by the plastic retaining ring at its base 2 Gently pull the windscreen away from microphone The plastic retaining ring will expand to allow the windscreen to slip off the microphone If necessary you can expand the ring manually with a small screwdriver a
3. ratio ref A weighted noise Output Clipping Level at 1000 Hz Maximum SPL Dynamic Range max SPL to A weighted noise level Output Noise equivalent SPL Recommended Operating Voltage Polarity Environmental Conditions Cable Cable Connector Net Weight voltage on pins 3 and 4 relative to pin 1 ground on the mini TA4F WH30TQG WH30XLR Condenser electret bias with integrated preamplifier 40 to 20 000 Hz See Figure 6 Condenser electret bias Unidirectional cardioid see Figure 7 Rated 150 actual Tolerates loads as low as 150 Q with reduced clipping level 55 5 dB 1 7 mV 54 5 dB 1 9 mV 63 0 dB at 94 dB SPL IEC 651 22 dBV 0 08 V 2 5KQ Load 8 dBV 0 4V 1 Load 8 dBV 0 4V 130 dB 2 5 Load 142 dB 1 Load 142 dB 99 dB 111 dB 31 dB typical A weighted 5 VDC pin 2 to pins 3 and 4 11 52 VDC Phantom power Positive sound pressure on diaphragm produces positive Positive sound pressure on the diaphragm produces positive voltage on pin 2 relative to pin 3 of preamplifier output connector connector Operating Temperature 7 to 49 C 20 to 120 Storage Temperature 29 to 74 C 20 to 165 Humid 0 to 95 96 operating or storage 3 05 m 10 ft two conductor shielded Headset 65 g 2 3 oz Headset and cord 60 g 2 1 oz Preamplifier 99 g 3 5 oz
4. 00 1212 In Europe Phone 49 7131 72140 Fax 49 7131 721414 In Asia Phone 852 2893 4290 Fax 852 2893 4055 Elsewhere Phone 847 600 2000 Fax 847 600 6446
5. SHURE Models WH30TQG WH30XLR User Guide MODEL WH30 CONDENSER HEADSET MICROPHONE WH30XLR ONLY 2003 Shure Incorporated A 2703121 Rev 4 C Printed in U S A INTRODUCTION The Shure Model WH30 is a light yet rugged headset microphone Designed for vocalists and instrument playing vocalists the WH30 utilizes high quality electret condenser cartridge suitable for all applications where mobility comfort low microphone visibility and high sound quality are required Because of its cardioid unidirectional pickup pattern the WH30 provides isolation from extraneous sound sources and high gain before feedback The wireframe and gooseneck adjust to any head size and shape An integrated elastic CROAKIES headband comfortably pads and secures the headset The WH30 is supplied with two snap on windscreens clothing clip storage bag and cable management device FEATURES e Smooth natural frequency response comparable to professional condenser hand held microphones Lightweight wireframe and headband adjust for a secure comfortable fit e Extra strong small diameter microphone cable resists breakage e Moisture proof cartridge housing Sturdy gooseneck boom holds mic securely in place e Isolation shock mount for reduced handling noise Matte black finish for low visibility e High input clipping level helps avoid overload distortion Low self noise and high sound pressure level capability e Reliable at temperatu
6. nd either above or below the wireframe for the greatest comfort and stability The blue SHURE logo should face outward see Figure 2 FIGURE 2 WEARING THE FIGURE 3 POSITIONING THE HEADSET MICROPHONE ADJUSTING THE HEADSET If the headset feels loose or uncomfortable carefully bend the sides of the wireframe to make it tighter or looser see Figure 4A The angle of the wire frame earpieces may also need adjustment see Figure 4B Adjust the tension of the elastic headband across the back of the head by slid ing it up or down the ends of the wireframe see Figure 5 FIGURE 4 ADJUSTING THE WIREFRAME 51 8 gt SS NA zo FIGURE 5 ELASTIC HEADBAND ADJUSTMENT USING THE CABLE RETAINER AND CLOTHING CLIP Use the cable retainer on the wire frame of the headset to position the microphone cable as desired The supplied spring loaded clothing clip secures the microphone cable to the user s clothing to help avoid entanglement POSITIONING THE MICROPHONE For maximum gain before feedback position the microphone and boom so that the microphone is within 13 mm 1 2 inch of the right corner of your mouth see Figure 3 This will also help minimize breath noise or popping CONNECTING THE WH30 TO A SOUND SYSTEM WIRELESS APPLICATIONS WH30TQG 1 Connect the mini TA4F connector from the WH30 to a wireless microphone transmitter such as the Shure T1 bodypack transmitter 2 See the user
7. re and humidity extremes MODEL VARIATIONS e WH30TQG For wireless use the WH30TQG has 1 5m 5 ft high flex cable and a mini TA4F connector for direct connection to Shure body pack transmit ters Note for information about use with Shure W10BT or other transmitters without a mini TA4F connector contact Shure Customer Service e WHS30XLR For wired applications the WH30XLR is supplied with 1 5m 5 ft hi flex cable high quality mic preamplifier RPM420 with a three pin XLR connector The RPM420 preamplifier requires phantom power from any 11 52 V source 1 51 5u MICROPHONE PARTS The WH30 consists of the following parts see Figure 1 NA 50 1 Microphone Cartridge and Windscreen 2 Microphone Boom and Cartridge Housing 3 Isolation Shock Mount 4 Boom Hinge rotates as shown 5 Cable 8 6 Elastic Headband 7 Wireframe 8 RPM420 Preamplifier WHSOXLR only FIGURE 1 WH30 HEADSET MICROPHONE PARTS COLLAPSIBLE MICROPHONE BOOM The WH30 headset features a collapsible boom for shipment and storage Before wearing the headset unfold the boom by rotating it away from the wireframe until it snaps into place Refold for storage or transportation WEARING THE HEADSET Place the headset wireframe around your head so that the elastic headband band lay horizontally across the back of your head and the ends of the wireframe fit over your ears You may position the elastic headba
8. s you pull the windscreen 3 Immerse the windscreen in mild soapy water and gently squeeze it several times 4 Rinse the windscreen in clean water and dry it with a clean cloth or paper tow el Allow it to air dry thoroughly 5 When the windscreen is dry slide it over the WH30 microphone until the re taining ring snaps into place CERTIFICATION The conforms to European EMC Directive 89 336 EEC and is eligible to bear the CE marking Meets applicable tests and performance criteria in European standard EN 55103 1996 parts 1 and 2 for residential E1 and light industrial E2 environments The WH30TQG conforms to European EMC Directive 89 33 EEC and is eligible to bear the CE marking Meets EMC require ments as an ancillary device EN 300 445 1996 REPLACEMENT PARTS Cable Connector for WH30TQG only WA330 Connector Belt Clip for WH30XLR only RK200BC Elastic Headband 80A505B Wireframe Headband Boom Hinge Boom Shock Mount Cartridge Housing and Cable RPM520 Preamplifier Assembly RPM420 Black Windscreens 2 and Clothing Clip 90WP1371 1 51 5u English SPECIFICATIONS Type Frequency Response Polar Pattern Output Impedance at 1kHz Output Level at 1 kHz 0 dB 1 V Pascal Signal to noise
Download Pdf Manuals
Related Search