Sherwood NetBoxx R-904N User's Manual
Contents
1. R 904N_quick guide_090915 R904N A quick guide 2009 10 14 3 44 Ho 2 1 E Please be certain that this unit is unplugged from the AC Outlet before making any connections E Be sure to observe the color coding when connecting audio video and speaker wires E For information about additions to the R 904N please see www sherwoodamerica com Navigate to NetBoxx 1 ANTENNA To receive FM broadcasts please connect the supplied antenna 2 CONNECTING SPEAKERS Be sure to connect speaker wires firmly and correctly according to channel and polarity For safe amplifier operation please use speakers with impedance of 60 or above To emphasize deep bass sounds connect a powered subwoofer 3 CONNECTING VIDEO COMPONENTS There are two sets of video jacks for analog video connections Component and Composite and HDMI connectors for digital video plus audio connections For your reference the video picture quality is as follows HDMI gt COMPONENT gt COMPOSITE Streaming and Internet Video are only supported from the HDMI and Composite Video output jacks 4 AUDIO SETUP To use the Auto Setup function connect the supplied microphone to the front panel SETUP MIC jack Select the Video 1 Input and press the SETUP button on the remote control Press the DOWN button on the remote until SET RMEQ appears on the display Press the ENTER button After a short wait the receiver will send increasingly loud test tones to each speaker in turn If all the sp2. ave a fee 13 For questions about the AV Streaming function VuUNow may be reached at 888 264 3985 NO of WD Sherwood America Incorporated Due to ongoing product improvements Sherwood reserves the right to change 13101 Moore Street Cerritos CA 90703 product specifications without prior notification Tel 800 962 3203 Fax 562 741 0967 www sherwoodamerica com All trademarks and registered trademarks are of their respective owners te Ce oO gt Z 2 o W e x lt x lt z 5227 00000 143 0S
3. eakers are located the EQ process will proceed after a short wait If the key speakers Main Left and Right are not located the unit will display ERR FCH and ask if you want to try again Please turn off any noise making devices in the room including AC Fans etc and press ENTER to retry When the RM EQ process is complete you will see PLS WAIT on the display then SET RMEQ will appear again This signifies that the AUTO SETUP is complete To complete the audio setup press the SOUND PARAMETER button on the remote control Press the DOWN button until EQ appears on the display Press the RIGHT button to turn the EQ on Press the DOWN button until D VOL appears on the display Press the RIGHT button to turn D VOL on Press the ENTER button LVL will appear on the screen press the RIGHT button to turn on Set other Dolby Volume parameters as desired using CURSOR buttons Dolby Volume is now engaged and all program material TV commercials Internet audio etc will be played back at the same SPINS HEIS YANO volume level VuNow AV STREAMING FUNCTION NetBoxx supports both wired and wireless Internet connectivity If you have a wired connection available insert the internet cable into the rear panel RJ 45 jack For wireless insert the supplied USB WIFI adapter into the rear panel USB input Make sure your TV is turned on and that the correct input Composite or HDMI has been selected 1 Press the VuNow b
4. utton on the remote control VuNow will begin booting If you are using the Composite Video connection it will take about 90 seconds to boot If you are using the HDMI connection after the unit boots in the Composite Video mode the boot process will pause for about 30 seconds and then re boot into the digital video mode This may take up to 3 minutes more Note The sound on the boot video may be quite loud Turn the volume control down When the boot process is complete the VuNow menu will appear on the screen Using the UP DOWN LEFT RIGHT and ENTER buttons on the remote navigate to SETTINGS Select NETWORK To choose your configuration select the NETWORK WIZARD Choose your network type WIRED or WIRELESS If you select WIRELESS choose your wireless network from the list of available networks Select your WEP input and press OK If you select WIRED go to Step 9 Enter the WEP key if necessary for your Wireless network using the Soft Keypad and press OK VuNow will automatically detect your home network internet settings and VuNow Server settings and conduct a download speed test of the connection When configuration is complete you will get a confirmation that the connection is established 10 Select DONE 11 Select the CH UP or CH DOWN button on the remote at any time to adjust the size of the video image 12 Some content like CinemaNow PlayOn for Hulu Netflix etc requires advance registration via PC and may h
Download Pdf Manuals
Related Search