Sharp CD-ES66 User's Manual
Contents
1. Use the direct search buttons on the remote control to select the de sired track while playing the se lected disc Selected track number The direct search buttons allow you to select up to number 9 When selecting number 10 or more use the 10 button A For example to choose 13 1 Press the 10 button once 2 Press the 3 button B For example to choose 30 1 Press the 10 button three times 2 Press the 0 button If the direct search buttons are pressed while the disc is stopped press the gt button to start the desired track on the current disc Notes A track number higher than the number of tracks on the disc can not be selected During random play direct search is not possible E Repeat play Repeat play can play all 5 discs all tracks on a chosen disc or a programmed sequence continuously To repeat all tracks on up to 5 discs Press the button twice To repeat desired tracks Perform steps 1 6 in the Programmed play section on page 20 and then press the gt button twice To cancel repeat play Press the gt button again will go out To repeat all tracks on the chosen disc 1 Press one of the G 1 G5 buttons F A 2 Within 5 seconds press the DIRECT PLAY dai button twice To cancel repeat play Press the DIRECT PLAY button again will go out m Random play The tracks on the disc s can be played in random or2. E Q L D OI iii IW AC outlet a aly AC 120 V 60 Hz E AC power connection see page 12 CD ES600 CD ES66 m Antenna connection WR Speaker connection Supplied FM antenna Connect the black wire to the minus terminal and the red wire to Connect the FM antenna wire to the FM 75 OHMS terminal and _ the plus terminal position the FM antenna wire in the direction where the strongest signal can be received Supplied AM loop antenna Connect the AM loop antenna to the AM LOOP jack Position the AM loop antenna for optimum reception Place the AM loop antenna on a shelf etc or attach it to a stand or a wall with screws not sup Sech Gang Sr ol Caution Use speakers with an impedance of 6 ohms or more as lower im L pedance speakers can damage the unit O Do not mistake the right and the left chan nels The right speaker is the one on the right C side when you face the unit Ke e Do not let the bare speaker wires touch Led each other NS Do not allow any objects to fall into or to be Y placed in the bass reflex ducts Q Note Do not stand or sit on the speakers You may Incorrect Q Placing the antenna on the unit or near the AC power cord may be injured D EE pickup Place the antenna away from the unit for better e Placing the speaker system The left and right speakers have individual shapes For best perfor Installing the AM loop antenna mance place the speak
3. SHARP MINI COMPONENT SYSTEM MODEL CD ES600 CD ES66 OPERATION MANUAL COMPACT DIGITAL AUDIO Thank you for purchasing this SHARP product To obtain the best performance from this product please read this manual carefully It will guide you in operating your SHARP product CD ES600 Mini Component System consisting of CD ES600 main unit and CP ES600 speaker system CD ES66 Mini Component System consisting of CD ES66 main unit and CP ES66 speaker system CD R RW A dg gt CCD CHAN GER Accessories Please confirm that the following accessories are included Remote control x 1 AM loop antenna x 1 FM antenna x 1 RRMCGO390AWSA QANTLOOO5AWZZ 92LFANT1746A Note Only the above accessories are included CD ES600 CD ES66 2 V S g GN Ben Q SPECIAL NOTES CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN A CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVIC ING TO QUALIFIED SERVICE PERSONNEL Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s en closure that may be of sufficient magnitude to constitute a risk of electric shock to per sons The exclamation point within an equilate
4. Tuner Preset Up Time Up Button 15 17 22 24 5 Clock Timer Button 0000 cee e eens 15 27 30 6 Tuning Up BUHON te enee seed keds ven eee ieee 21 7 Tuning Down Button 022 eee eee 21 8 CD Track Down or Fast Reverse Tape 2 Rewind Tuner Preset Down Time Down Button 15 17 22 24 9 Equalizer Mode Select Button 0000 cues 14 10 Tape 1 Cassette Compartment 00 00s 23 11 Headphone Jack ag SEENEN sees 32 12 Game Video Input Jacks 0 00 eeeeeeeees 31 13 Disc Number Select Buttons 22000 ees 16 14 CD Direct Play BUON lt cvspidses cece ete ers exes 18 15 Disc Tray Open Close Button 16 16 CD Play or Repeat Tape Play Button 16 19 23 17 Memory Set Button 15 20 22 27 30 18 Tape 2 Record Pause Button 052 25 26 19 CD or Tape Stop Button 002 ee ee eeee 17 24 20 Extra Bass Demo Mode Button 12 14 21 Volume Control 202 c eee eee 14 22 Tape 2 Cassette Compartment 00eee eee 23 23 Tuner Band Button 21 24 CD BUON EE EE 16 25 Tape 1 2 Button WEE 23 26 Game Video Button 0 02 e eee 31 CD ES600 CD ES66 2 iw o gt Pm V o S O CD ES600 CD ES66 S 2 ew o sS Pm L z O Controls and indicators continued dd gue AU IM mila Gear iA i sre ED m Display R
5. between operations E Timer playback or timer recording Before setting timer 1 Check that the clock is set to the correct time refer to page 15 If it is not set you cannot use the timer function 2 For timer playback Load a cassette or discs to be played For timer recording Load a cassette for recording in the cas sette compartment 1 Press the ON STAND BY button to turn the power on 2 Press the CLOCK TIMER button 3 Within 10 seconds press the lt a lt lt or gt gt gt gt button to select ONCE or DAILY and press the MEMORY SET button Set the unit to the correct time if ONCE or DAILY does not appear Continued to the next page CD ES600 CD ES66 Al L S skas gt all Q gt lt cots Timer and sleep operation continued Within 10 seconds press the lt lt lt lt or gt gt gt gt button to se 9 Switch input with the da lt lt or gt gt PPI button and then lect ONCE SET or DAILY SET and press the MEMORY press the MEMORY SET button SET button To select the timer playback source CD TUNER TAPE 1 or TAPE 2 To select the timer recording source TUNER When you select the tuner select a station by pressing the Press the ga lt lt or gt gt PPI button to select PLAY or L a lt lt or gt gt PPI button and then press the MEMORY SET REC and press the MEMORY SET button button f a station has not been programmed NO P SE
6. the guidelines below for maximum enjoyment from your CD collec tion and player Do not write on either side of the disc particularly the non label side from which signals are read Do not mark this surface Keep your discs away from direct sunlight heat and excessive moisture Always hold the CDs by the edges Fingerprints dirt or water on the CDs can cause noise or mistracking If a CD is dirty or does not play properly clean it with a soft dry cloth wiping straight out from the center along the radius YES Correct Maintenance E Cleaning the tape handling parts Dirty heads capstans or pinch rollers can cause poor sound and tape jams Clean these parts with a cotton swab moistened with commercial head pinch roller cleaner or isopropyl alcohol When cleaning the heads pinch rollers etc unplug the unit which contains high voltages OG Be TAPE 1 Im ef Pal a i Z A bee head Capstan Pinch roller D Erase head Recording Playback head After long use the deck s heads and capstans may become mag netized causing poor sound Demagnetize these parts once every 30 hours of playing recording time by using a commercial tape head demagnetizer Read the demagnetizer s instructions carefully before use WR Cleaning the CD pickup lens In order to ensure proper operation of the CD player preventative maintenance cleaning of the laser pickup lens should be per formed periodically Lens
7. Frequency range FM 87 5 108 0 MHz AM 530 1 720 kHz m Cassette deck Frequency re 50 14 000 Hz normal tape sponse Signal noise ratio 55 dB TAPE 1 playback 50 dB TAPE 2 recording playback Wow and flutter 0 3 WRMS E Speaker Type 2 way type speaker system with passive radiator 2 5 cm tweeter 5 1 8 13 cm woofer 4 10 cm passive radiator Maximum input 240 W power Rated input power 120 W Width 9 7 8 252 mm Height 13 330 mm Depth 9 13 16 249 mm Weight 7 9 bs 3 6 kg each CD ES600 CD ES66 Al ol Q a S LC CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product the Product when shipped in its original con tainer will be free from defective workmanship and materials and agrees that it will at its option either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period s set forth below This warranty does not apply to any appearance items of the Product nor to the additional excluded item s set forth below nor to any Product the exterior of which has been damaged or defaced which has been subjected to improper voltage or other misuse abnormal service or handling or which has been altered or modified in design or construction In order to enforce the rights under this limit
8. and then turn on your system Incase of an electrical storm unplug the unit for safety ee CL D Hold the AC power plug by the head when removing it from the AC outlet as pulling the cord can damage internal wires Do not remove the outer cover as this may result in electric shock Refer inter nal service to your local SHARP service facility This unit should only be used within the range of 41 F 95 F 5 35 C Warning The voltage used must be the same as that specified on this unit Using this product with a higher voltage other than that which is specified is dangerous and may result in a fire or other type of acci dent causing damage SHARP will not be held responsible for any damage resulting from use of this unit with a voltage other than that which is specified WR Volume control The sound level at a given volume setting depends on speaker effi ciency location and various other factors It is advisable to avoid exposure to high volume levels which occurs while turning the unit on with the volume control setting up high or while continually lis tening at high volumes Controls and indicators D Kl TTT TE 11 12 E Front panel Reference page TL Dis Ways ccvcctntewdicwe eeeiee eis eee ete eaetes 16 2 Timer Indicator 6 225655 86004 ce vee ened CARE OES Os Eee 28 3 Power On Stand by Button 02002 eee eee 14 4 CD Track Up or Fast Forward Tape 2 Fast Forward
9. 13 2 Disc Number Select Buttons ee 16 3 CD Clear Dimmer Button 002 ce eee 14 20 4 Memory Set Button 15 20 22 27 30 5 CD Random Button ees 19 6 CD Track Down or Fast Reverse Tape 2 Rewind Tuner Preset Down Time Down Button 15 17 22 24 7 Tape 2 Record Pause Button 0e eee 25 26 8 Equalizer Mode Select Button 0000 eee 14 9 Tuner Band Button ocicscssencteees detec cue genes 21 10 CD Button o 02c4c erneeeex Cesc beads cecece see Saees 16 11 Power On Stand by Button 220002 eee 14 12 Extra Bass Button es 14 13 Clock Timer Button 002 eee eens 15 27 30 14 Disc Direct Search Buttons 0002 eee 18 15 CD Pause Button 2 cpe0s86ic006us enw ewies dee edocs 17 16 CD Track Up or Fast Forward Tape 2 Fast Forward Tuner Preset Up Time Up Button 15 17 22 24 17 CD or Tape Stop Button 17 18 CD Play or Repeat Tape Play Button 16 19 19 Game Video Button 31 20 Tape 1 2 Button es 23 21 Volume Up and Down Buttons 00 cee eee 14 CD ES600 CD ES66 2 iw o V o S O cee System connections Make sure to unplug the AC power cord before any connections E Antenna connection see page 11 AM loop antenna FM antenna Right speaker Left speaker i HH ll u o LIT aaa g EE ml LE A dd du E e cl Ben
10. 4 Ch ri l l 1 l US If the MEMORY and preset number indicators go out before the station is memorized repeat the operation from step 2 Repeat steps 1 4 to set other stations or to change a pre set station m To erase entire preset memory When a new station is stored in memory the station previously 1 Press the ON STAND BY button to enter the stand by mode memorized will be erased 2 While pressing down the eut button and the X BASS DEMO but ton press the CLOCK TIMER button until TUNER CL appears Note The backup function protects the memorized stations for a few hours hould there b fail he AC d di i d should there be a power failure or the AC power cord disconnection ell QO D gt QO dai d Listening to a cassette tape TAPE 1 or TAPE 2 eee Before playback E Tape playback For playback use normal or low noise tapes for the best sound Metal or CrO tapes are not recom mended Do not use C 120 tapes or poor quality tapes as they may cause malfunctions Before loading a tape into the cassette compartment tighten the slack with a pen or a pencil 2 Open the cassette com van PEP IT partment by pushing the UPOS Up US area marked 4 Y a T le a Nd D eeey Load a cassette into the TAPE 1 compartment or Te ei gars EE with BURE the side to be played fac E SH ing towards you 4 UAA Press the TAPE 1 2 button to select the cassette you want to lis
11. Press the W button TAPE 1 and TAPE 2 will simultaneously stop m Erasing recorded tapes 1 Load the tape to be erased into the TAPE 2 cassette compart ment with the side to be erased facing toward you 2 Press the TAPE 1 2 button until TAPE 2 appears on the dis play 3 Press the eut button 4 Press the button to start erasing Note Make sure that the TAPE 1 is not in use Timer and sleep operation Timer playback The unit turns on and plays the desired source CD tuner tape at the preset time Timer recording The unit turns on and starts recording from the tuner at the preset time This unit has 2 types of timer ONCE TIMER and DAILY TIMER Once timer play and once timer recording works for one time only at a preset time For example if you are away but want to record a program on a ra dio station Once timer Daily timer play and daily timer recording works at the same preset time everyday For example set the timer as a wake up call every morning Daily timer Using the once timer and daily timer in combination For example use the once timer to record a radio program and use the daily timer as an alarm clock 1 Set the daily timer pages 27 29 2 Set the once timer pages 27 29 1 minute or more Once timer Daily timer Note When the setting times for the daily timer and once timer overlap the once timer takes priority Allow an interval of at least 1 minute
12. S sl e LC Q Ss Recording on a cassette tape continued Recording from several CDs continuously 1 Perform steps 1 5 in Recording from a CD CDs on page 25 2 Within 5 seconds press the gt S To perform programmed recording 1 Program discs and tracks See page 20 2 Press the eut button 3 Press the G To stop recording Press the W button The CD and tape will stop E Recording from the radio 1 Tune in to the desired station See page 21 2 Load a cassette into the TAPE 2 cassette compartment with the side to be recorded on facing you Wind past the leader of the tape on which recording cannot be performed 3 Press the geit button Recording will be paused 4 Press the gt button to start recording To interrupt recording Press the eut button To resume recording press the gt S button To stop recording Press the W button Note If you hear a whistling noise while recording an AM station move the AM loop antenna WR Dubbing from tape to tape You can record from TAPE 1 to TAPE 2 1 Press the ON STAND BY button to turn the power on 2 Load a prerecorded cassette A ee E OH into the TAPE 1 cassette com Jee partment Insert a blank tape i Lesa into the TAPE 2 cassette com i iad partment Loe A It is recommended that the recording tape is the same length as the master tape 4 Press the ei button Recording will be paused To stop dubbing
13. See Instruction Manual for replacement or resetting of protective device If replacement of the plug is required be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug CD ES600 CD ES66 Gul Q GN en 8 S CD ES600 CD ES66 S 2 L I S GN en Q 15 Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an an tenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode Example of antenna grounding as per National Electrical Code ANSI NFPA 70 ANTENNA LEAD IN WIRE GROUND ANTENNA DISCHARGE UNIT NEC SECTION 810 20 ELECTRIC SERVICE GROUNDING CONDUCTORS NEC SECTION 810 21 GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE S2898A 16 Lightning For added protection for this product during a lightning storm or when it
14. White Red White Yellow ITU AS Red 7 J Ki RCA cord not supplied GAME INPUT VIDEO AUDIO R 999 To video input jack E Yellow Video cable not supplied E Listening to playback sounds of Game VCR DVD etc 1 Connect a video game system VCR DVD etc to the front GAME INPUT VIDEO AUDIO L and R jacks 2 Connect a TV to the rear VIDEO OUT jack Switch the TV input to auxiliary 3 Press the ON STAND BY button to turn the power on 4 Press the GAME VIDEO button 5 Play the connected equipment You can enjoy sounds from the supplied speakers and images on the TV Note To prevent noise interference place the unit away from the television Auto power on function When you press any of the following buttons the unit turns on GAME VIDEO button main unit and remote control The unit turns on and the GAME function is activated gt c button main unit and remote control The unit turns on and playback of the last function starts CD TAPE TUNER GAME WR To record on a tape from Game VCR etc 1 Insert a cassette in the TAPE 2 cassette compartment 2 Press the GAME VIDEO button 3 Press the i button 4 Press the gt button 5 Play the game system VCR etc CD ES600 CD ES66 2 L S skas G Q gt lt CD ES600 Troubleshooting chart CD ES66 m Headphones Many potential problems can be resolved by
15. automatically canceled Even if you press the ON STAND BY button to enter the stand by mode or change the function from CD to another the pro grammed selections will not be cleared During the program operation random play is not possible During programmed play the DIRECT PLAY buttons will not work Listening to the radio e Auto power on function When you press any of the following buttons the unit turns on TUNER BAND button main unit and remote control The unit turns on and the TUNER function is activated gt C button main unit and remote control The unit turns on and playback of the last function starts CD TAPE TUNER GAME WR Tuning 1 Press the ON STAND BY button to turn the power on 2 Press the TUNER BAND button repeatedly to select the desired frequency band FM or AM 3 Press the TUNING V or button to tune in to the desired station Manual tuning Press the TUNING button as many times as required to tune in to the desired station Auto tuning When the TUNING button is pressed for more than 0 5 sec onds scanning will start automatically and the tuner will stop at the first receivable broadcast station Notes When radio interference occurs auto scan tuning may stop auto matically at that point Auto scan tuning will skip weak signal stations To stop the auto tuning press the TUNING button again To receive an FM stereo transmission Press
16. cleaners are commercially available Con tact your local CD software dealer for options m Cleaning the cabinet Periodically wipe the cabinet with a soft cloth and a diluted soap solution then with a dry cloth Caution Do not use chemicals for cleaning gasoline paint thinner etc It may damage the cabinet finish Do not apply oil to the inside of the unit It may cause malfunctions Specifications As part of our policy of continuous improvement SHARP reserves the right to make design and specification changes for product improvement without prior notice The performance specification fig ures indicated are nominal values of production units There may be some deviations from these values in individual units E General Power source AC 120 V 60 Fz Power consump 108 W tion Width 10 1 4 260 mm Height 13 330 mm Depth 12 7 8 326 mm Weim 172s 78 ka m Amplifier Output power 120 watts minimum RMS per channel into 6 ohms from 100 Hz to 20 kHz 10 total har monic distortion Output terminals Speakers 6 ohms Headphones 16 50 ohms recommended 32 ohms Video output 1Vp p Input terminals Game Auxiliary audio signal 500 mV 47 k ohms Game Video 1 Vp p m CD player 5 disc multi play compact disc player Signal readout Non contact 3 beam semiconductor laser pickup D A converter 1 bit D A converter 20 20 000 Hz Frequency re sponse 30 dB 1 KHz E Tuner
17. the TUNER BAND button to display the ST indicator will appear when an FM broadcast is in stereo f the FM reception is weak press the TUNER BAND button to extinguish the ST indicator The reception changes to monau ral and the sound becomes clearer FM stereo mode indicator Cha deele ry a L FM stereo receiving indicator CD ES600 CD ES66 cocs Listening to the radio continued E Memorizing a station m To recall a memorized station You can store 40 AM and FM stations in memory and recall them at Press the PRESET V or button for less than 0 5 seconds to se the push of a button Preset tuning lect the desired station 1 Perform steps 1 3 in Tuning on page 21 RH To scan the preset stations The stations saved in memory can be scanned automatically Pre 2 Press the MEMORY SET MEMORY button to enter the set memory scan preser tuning saving mode 1 Press the PRESET V or 4 button for more than 0 5 seconds The preset number will flash and the programmed stations will be tuned in sequentially for 5 seconds each 2 Press the PRESET V or button again when the desired sta tion is located Within 30 seconds press the PRESET V or N button to select the preset channel number Store the stations in memory in order starting with preset h channel 1 Within 30 seconds press the MEMORY SET MEMORY button to store that station in memory ae ee
18. the owner without call ing a service technician Before plugging in or unplugging the headphones reduce the vol If something is wrong with this product check the following before ume e Be sure your headphones have a 1 8 3 5 mm diameter plug calling your authorized SHARP dealer or service center and are between 16 ohms and 50 ohms impedance The recom E G l mended impedance is 32 ohms enera Plugging in the headphones disconnects the speakers automati Symptom lly Adj h ing the VOLUME control Sale Rates Cie VOLTE USIMG IMENE come The clock is not set to the Did a power failure occur Reset correct time the clock Refer to page 15 When a button is pressed Set the unit to the power stand the unit does not respond by mode and then turn it back on Ifthe unit still malfunctions reset it Refer to page 33 No sound is heard Is the volume level set to 0 Are the headphones connected Are the speaker wires discon nected m CD player Symptom Playback does not start Is the disc loaded upside down Playback stops in the mid Does the disc satisfy the stan dle or is not performed dards properly Is the disc distorted or scratched Al 2 S sks Ww D Q Q gt lt Playback sounds are Is the unit located near excessive skipped or stopped in the vibrations middle of a track Is the disc very dirty Has condensation formed inside the un
19. T will be displayed and timer setting will be canceled ri 10 Adjust the volume using the VOLUME control and then press the MEMORY SET button Do not turn the volume up too high Press the La lt lt or gt gt gt gt button to adjust the hour and 11 Press the ON STAND BY button to enter the power stand then press the MEMORY SET button by mode The TIMER indicator lights up and the unit is ready for timer playback or timer recording The illustrations show the timer playback setting in the daily tim er mode T Press the lt lt lt or gt gt gt gt I button to adjust the minutes and then press the MEMORY SET button Al S skas Ww D Q gt lt TI NA IlI 8 Set the time to finish as in steps 6 and 7 above 12When the preset time is reached playback or recording will start The volume will increase gradually until it reaches the preset volume 13When the timer end time is reached the system will enter the power stand by mode automatically Once timer The timer will be canceled Daily timer The timer will operate at the same time every day It will contin ue until the daily timer setting is canceled Cancel the daily timer when it is not used Note When performing timer playback or recording using another unit con nected to the GAME INPUT jacks select GAME in step 9 This unit will turn on or enter the power stand by mode automatically however the connected un
20. be liable or in any way responsible for any incidental or consequential economic or property damage Some states do not allow the exclusion of incidental or consequential damages so the above exclusion may not apply to you THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Model Specific Section Your Product Model Number amp Description CD ES600 CD ES66 Mini Component System Be sure to have this information available when you need service for your Product Warranty Period for this Product One 1 year parts and labor from the date of purchase Additional Item s Excluded from Warranty Coverage if any Non functional accessories supplies and consumable items Where to Obtain Service At a Sharp Authorized Servicer located in the United States To find a location of the nearest Sharp Authorized Servicer call Sharp toll free at 1 800 BE SHARP What to do to Obtain Service Ship prepaid or carry in your Product to a Sharp Authorized Servicer Be sure to have Proof of Purchase available If you ship the Product be sure it is insured and packaged securely TO OBTAIN SUPPLY ACCESSORY OR PRODUCT INFORMATION CALL 1 800 BE SHARP SHARP SHARP ELECTRONICS CORPORATION Sharp Plaza Mahwah New Jersey 07430 2135 Printed in Malaysia TINSEAOO5AWZZ SHARP CORPORATION 03M R YT
21. beled products you will save money on your electric bills and use less energy That makes good economic sense and it s good for our environment m Advanced Features Timer and sleep operation ee eeeee To comply with the ENERGY STAR standards mentioned above Enhancing your system please cancel the demonstration mode as described on page12 E References Troubleshooting chart eee ee eens MaINIGNANGCe a Se Ee ER SE Ee e aces SPECHICAIONS 24254 Gelee EE EELER E ENERGY STAR is a U S registered mark CONSUMER LIMITED WARRANTY CD ES600 CD ES66 S 2 ew o z sS Pm L z O Precautions E General Please ensure that the equipment is positioned in a well venti lated area and ensure that there is at least 4 10 cm of free space along the sides top and back of the equipment 10cm 4 10 cm 4 a Use the unit on a firm level surface free from vibration Keep the unit away from direct sunlight strong magnetic fields excessive dust humidity and electronic electrical equip ment home computers facsimiles etc which generate electrical noise Do not place anything on top of the unit Do not expose the unit to moisture to temperatures higher than 140 F 60 C or to extremely low temperatures f your system does not work properly disconnect the AC power cord from the AC outlet Plug the AC power cord back in
22. bjects have fallen into the product c If the product has been exposed to rain or water d If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the op erating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation e If the product has been dropped or damaged in any way and f When the product exhibits a distinct change in performance this indicates a need for service 22 Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards 23 Safety Check Upon completion of any service or repairs to this prod uct ask the service technician to perform safety checks to determine that the product is in proper operating condition 24 Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer 25 Heat The product should be situated away from heat sources such as radiators heat registers stoves or other products including ampli fiers that produce heat Contents SE E General Information ENERGY STAR Program Information Weeden CN SN Controls and mdca
23. ct the recorded sound remove the tab after recording D Cover the tab hole with adhesive tape to record on the tape with ai out the tab Q Caution 2 To remove the cassette press the W button and then open the m compartment Before changing from one tape operation to another press the E button f a power failure occurs during tape operation the tape head will remain engaged with the tape and the cassette door will not open In this case wait until the power is restored DISC SELECT Gi G2 CO GA 65 C 5 Cm Recording from a CD CDs You can record the desired CD using the DIRECT PLAY button 3 Load a cassette into the TAPE 2 cassette compartment with the side to be recorded on facing you Wind past the leader of the tape on which recording cannot be performed 4 Press the ll button Recording will be paused 5 Press one of the 1 5 buttons to select the desired disc 6 Within 5 seconds press the DIRECT PLAY button to start recording Recording is started from the selected CD When the play back of the last track is finished or the end of the tape is reached the CD and the cassette will stop automatically CD playback will start approximately 7 seconds after the tape starts To stop recording Press the W button The CD and tape will stop CD ES600 CD ES66 e g O e LC Q K CD ES600 CD ES66 e
24. d of the unit m Clearing all the memory reset not operate plugged in 1 Press the ON STAND BY button to enter the power stand by mode Is the battery polarity correct 2 While pressing down the II button and the X BASS DEMO but Are the batteries dead ton press the Kk ga PRESET button until CLEAR AL Is the distance or angle incor appears rect Does the remote control sensor oa O ee receive strong light val CSS jen Caution This operation will erase all data stored in memory including clock timer settings tuner preset and CD program CD ES600 CD ES66 Q a x S LC m Condensation Sudden temperature changes storage or operation in an extremely humid environment may cause condensation inside the cabinet CD pickup tape heads etc or on the transmitter on the remote control Condensation can cause the unit to malfunction If this happens leave the power on with no disc or cassette in the unit until normal playback is possible about 1 hour Wipe off any condensation on the transmitter with a soft cloth before operating the unit E Before transporting the unit Remove all CDs from the unit Make sure there is no CD in the disc tray Then set the unit to the power stand by mode Carrying the unit with discs left inside can damage the unit E Care of compact discs Compact discs are fairly resistant to damage however mistracking can occur due to an accumulation of dirt on the disc surface Follow
25. demonstration mode press the X BASS DEMO button The unit will enter the low power consumption mode the demonstration X BASS DEMO Note When the power is on the X BASS DEMO button can be used to se lect the extra bass mode E Outdoor FM antenna Use an outdoor FM antenna if you require better reception Consult your dealer Outdoor FM antenna WEI 75 ohm coaxial cable Note When an outdoor FM antenna is used disconnect the supplied FM antenna wire Remote control m Battery installation Use 2 AA size batteries UM SUM 3 R6 HP 7 or similar Batteries are not included Remove the battery cover Insert the batteries according to the direction indicated in the battery compartment When inserting or removing the batteries push them toward the battery terminals 3 Replace the cover N sech Precautions for battery use Replace all old batteries with new ones at the same time Do not mix old and new batteries Remove the batteries if the unit will not be used for long periods of time This will prevent potential damage due to battery leak age Caution Do not use rechargeable batteries nickel cadmium battery etc Installing the batteries incorrectly may cause the unit to malfunc tion Notes concerning use Replace the batteries if the operating distance is reduced or if the operation becomes erratic Periodically clean the transmitter on
26. der automatically To random play all tracks on up to 5 discs Press the RANDOM button on the remote control RANDOM To cancel random play Press the gt button R will go out To random play all tracks on the chosen disc 1 Press one of the 1 5 buttons A RANDOM 2 Within 5 seconds press the DI Ss RECT PLAY button 3 Press the RANDOM button on the remote control G VA daf To cancel random play Press the DIRECT PLAY button R will go out Notes f you press the gt gt I button during random play you can move to the track selected next by the random operation On the other hand the ka button does not allow you to move to the previous track The beginning of the track being played will be located In random play the CD player will select and play tracks automat ically You cannot select the order of the tracks Caution After performing repeat or random play be sure to press the but ton Otherwise the disc s will play continuously CD ES600 CD ES66 S S a A S CD ES600 CD ES66 S S a A O Advanced CD Playback continued E Programmed play You can choose up to 32 selections for playback in the order you like 1 While in the stop mode press the MEMORY SET MEMORY button to enter the programming save SZ 2 Press one of the 1 5 buttons to select the desired disc 3 Press the direct search buttons on the remote co
27. ed warranty the purchaser should follow the steps set forth below and provide proof of purchase to the servicer The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD S FROM THE DATE OF PURCHASE SET FORTH BELOW Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser Correction of defects in the manner and for the period of time described herein shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product and shall constitute full satisfaction of all claims whether based on contract negligence strict liability or otherwise In no event shall Sharp be liable or in any way responsible for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer Nor shall Sharp
28. eference page 1 Disc Number Indicators 0200 eee eee eee 18 2 CD Play Indicator s ebe See EE eee iver ss 16 3 CD Pause Indicator tree See ER ee 17 4 Memory Indicator 20 5 CD Repeat Play Indicator 00002 cece 19 6 CD INGIGAION 2c eee tee Me bide HENS oe ee Ke 16 7 Extra Bass IESSE scsi seed eee ce teas eas 14 8 Tape Play Indicator 00 202 e eee eee 23 9 FM Stereo Mode Indicator 00002e eee 21 10 Daily Timer Indicator 28 11 FM Stereo Receiving Indicator 21 12 Tape 2 Record Indicator 002 00 e ee eens 25 13 DICED INGICGION ANE eet eter ees eed ince ee de 30 14 Timer Play Indicator 2202 2 eee eee eens 28 15 Timer Recording Indicator 200eee eens 28 m Rear panel ei e ut EE 12 2 AC Power Cord lt i cece EE ei week eee eee d NEE 12 3 FM 75 Ohms Antenna Terminal 000005 11 4 FM Antenna Ground Terminal 002000000es 11 5 AM Loop Aerial Jack 11 6 Video Output Jack gie ccc te eee eee ed ee eee eens 31 7 speaker Terminals 635666108040 iee terres A 11 E Speaker system 1 Tweeter 2 Passive Radiator 3 Woofer 4 Speaker Wire 13 3 4 5 6 T Lime es Zelt 53 5 e 7 E bg le eu i UI i Cm ma TUNER pata 9 10 STAND BY X BASS VOL WU o 2 IM h 21 AUDIO SYSTEM E Remote control Reference page 1 Remote Control Transmitter 0 00 eee eee
29. ers according to the diagram below lt Assembling gt lt Attaching to the wall gt Left speaker Right speaker IS A gt Wall Screws not supplied Note The speaker grilles are not removable CD ES600 CD ES66 e cl Ben Q L D System connections continued E AC power connection After checking all the connections have been made correctly plug the AC power cord of this unit into the AC outlet If you plug in the unit first the unit will enter the demonstration mode AC outlet AC 120 V 60 Hz Notes The unit will start the tape initialization when plugged in to the AC outlet During this process an initializing sound will be heard and the unit cannot be turned on Wait until the process is finished Unplug the AC power cord from the AC outlet if the unit will not be in use for a prolonged period of time Cooling fan This product is equipped with a cooling fan inside which begins to run once the power is on for better heat radiation m Demonstration mode The first time the unit is plugged in the unit will enter the demonstration mode LIE e d You will see words scroll d To return to the demonstration mode When the unit is in the power stand by mode press the X BASS DEMO button again To cancel mode When the unit is in the power stand by mode
30. hile SLEEP is indicated To cancel the sleep operation without setting the unit to the stand by mode proceed as follows 1 While SLEEP is indicated press the CLOCK TIMER button 2 Within 10 seconds press the Kt lt lt or gt gt PPI button to select SLEEP OFF and press the MEMORY SET button m To use timer and sleep operation together Sleep and timer playback For example you can fall asleep listening to the radio and wake up to CD in the next morning Sleep and timer recording For example you can fall asleep listening to the CD and record radio programs while sleeping 1 Set the sleep time see left steps 1 5 2 While the sleep timer is set set the timer playback or recording steps 2 10 pages 27 28 Timer playback or recording setting End time Sleep timer setting 1 minute 3 hours Timer playback or recording start time Sleep operation will automatically stop Caution When using the cassette deck be sure the tape length is long enough to perform both functions If you want to sleep and wake up listening to a tape and the length of the tape is shorter than the sleep timer setting timer playback or recording will not be possible Enhancing your system The connection cord is not included Purchase a commercially avail able cord as shown below GAME or VCR DVD etc r CH To the line output jacks Video cable not supplied a Yellow
31. hile playing a disc Press one of the 1 5 buttons for the stopped disc and within 5 seconds press the OPEN CLOSE button and exchange discs To remove the CDs In the stop mode press the 1 5 button and within 5 seconds press the OPEN CLOSE button rag beats Do not place two CDs in one disc tray Do not play discs with special shapes heart or octagon shaped It may cause malfunctions Do not push the disc tray while it is moving f the power fails while the tray is open wait until the power is restored f the disc tray is stopped with force ER CD20 will appear on the display for 3 seconds and the unit will not function If this occurs press the ON STAND BY button to enter the power stand by mode and then turn the power on again if TV or radio interference occurs during CD operation move the unit away from the TV or radio f adisc is damaged dirty or loaded upside down the disc will be skipped Auto power on function When you press any of the following buttons the unit turns on CD button main unit and remote control The unit turns on and the CD function is activated gt button main unit and remote control The unit turns on and playback of the last function starts CD TAPE TUNER GAME E Various CD functions Remote Operation control Press in the stop mode Press in the playback mode Press in the playback mode Press the gt button to resu
32. is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges 17 Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal 18 Overloading Do not overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock IMPORTANT SAFETY INSTRUCTIONS continued 19 Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product 20 Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 21 Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or o
33. it CD ES600 CD ES66 E Cassette deck E Tuner Symptom Symptom Cannot record Is the erase prevention tab re The radio makes unusual Is the unit placed near the TV or moved noises continuously computer Is the FM antenna or AM loop an Cannot record tracks with Is ita normal tape You cannot S proper sound quality record on a metal or CrO tape tenna placed properly Move the antenna away from the AC power Cannot erase completely cord if it s located nearby Sound skipping Is there any slack Is the tape stretched WR If trouble occurs Cannot hear treble e Are the capstans pinch rollers When this product is subjected to strong external interference or heads dirty mechanical shock excessive static electricity abnormal supply voltage due to lightning etc or if it is operated incorrectly it may Sound fluctuation Cannot remove the tape If a power failure occurs during malfunction o playback the heads remain en If such a problem occurs do the following LH gaged with the tape Do not open 1 Set the unit to the stand by mode and turn the power on again the compartment with great 2 If the unit is not restored in the previous operation unplug and E force plug in the unit and then turn the power on Note If neither operation above restores the unit clear all the memory by HA WR Remote control EE X Symptom The remote control does Is the AC power cor
34. it will not turn on or off Checking the timer setting in the timer stand by mode 1 Press the CLOCK TIMER button 2 Within 10 seconds press the Kt lt lt or gt gt PPI button to select ONCE or DAILY and press the MEMORY SET button 3 Within 10 seconds press the Kt lt lt or gt gt PPI button to select ONCE CAL or DAILY CAL and press the MEMORY SET but ton The unit returns to the timer stand by mode after displaying the settings in order Canceling the timer setting in the timer stand by mode 1 Press the CLOCK TIMER button 2 Within 10 seconds press the Kt lt lt or gt gt PPI button to select ONCE or DAILY and press the MEMORY SET button 3 Within 10 seconds press the Kt lt lt or gt gt PPI button to select ONCE OFF or DAILY OFF and press the MEMORY SET but ton Timer will be canceled the setting will not be canceled Reusing the memorized timer setting The timer setting will be memorized once it is entered To reuse the same setting perform the following operations 1 Turn the power on and press the CLOCK TIMER button 2 Within 10 seconds press the Kt lt lt or gt gt PPI button to select ONCE or DAILY and press the MEMORY SET button 3 Within 10 seconds press the Kt lt lt or gt gt PPI button to select ONCE ON or DAILY ON and press the MEMORY SET button 4 Press the ON STAND BY button to enter the power stand by mode Note The timer can also be set
35. me play back from the paused point Press in the playback or stop mode If you press the button in the stop mode press the gt button to start the desired track Press and hold down in the playback mode Release the button to resume playback Track up Track down Fast for ward Fast reverse Notes Track up track down and fast forward fast reverse are possible only within individual discs When the end of the last track is reached during fast forward xx END will appear on the display and CD operation will be paused When the beginning of the first track is reached during fast re verse the unit will enter the playback mode xx Last track number CD ES600 CD ES66 S rs S a A O CD ES600 CD ES66 P S a A O Advanced CD playback WR To specify a disc to play You can play a disc by specifying the disc number 1 Press one of the 1 5 buttons to select the desired disc 2 Within 5 seconds press the DIRECT PLAY button on the main unit Playback will begin from track 1 on the chosen disc After the last track on the chosen disc is played the CD player stops automatically Note If the button of the disc tray with no disc is pressed playback will not start and the disc indicator will go out To stop playback Press the W button WR Direct track search By using the direct search buttons the desired tracks on the current disc can be played
36. ntrol to select the desired track Selected track number You can also select a track by pressing the K lt or gt P button 4 Press the MEMORY SET MEMO RY button to save the track number 5 Repeat steps 2 4 for other tracks Up to 32 tracks can be programmed If you make a mistake the programmed tracks can be cleared by pressing the CLEAR DIMMER button 6 Press the E button The total number of memory will ap pear T Press the gt button to start playback To clear the programmed selections Press the CLEAR DIMMER button on the re CLEAR mote control while the MEMORY indicatoris DIMMER flashing Each time the button is pressed one track will be cleared beginning with the last track pro grammed isc SELECT oS TUNER p TAPE GAME LZ To cancel the programmed play mode While in the stop mode and the MEMORY indicator is lit press the CLEAR DIMMER button on the remote control The MEMORY indicator will disappear and all the programmed contents will be cleared Adding tracks to the program If a program has been previously stored the MEMORY indicator will be displayed Then follow steps 1 6 to add tracks The new tracks will be stored after the last track of the original program To check which tracks are programmed While the unit is stopped in the programmed play mode press the Wa or PPI button Notes When a disc with programmed tracks is ejected the program is
37. of the type of power supply to your home consult your product dealer or local power company For products intended to operate from battery power or other sources refer to the operating instructions 12 Grounding or Polarization This product may be equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug Alternate Warnings This product is equipped with a three wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact your electri cian to replace your obsolete outlet Do not defeat the safety purpose of the grounding type plug 13 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the product 14 Protective Attachment Plug The product is equipped with an at tachment plug having overload protection This is a safety feature
38. on Press the VOLUME or button to in crease or decrease the volume E Bass control When the power is first turned on the unit will enter the extra bass mode which em phasizes the bass frequencies and X BASS will appear To cancel the extra bass mode press the X BASS DEMO X BASS button WR Equalizer When the EQUALIZER EQUALIZER MODE button is pressed the current mode setting will be displayed To change to a different mode press the EQUALIZER EQUALIZER MODE button repeat edly until the desired sound mode appears During CD TUNER TAPE mode During GAME VIDEO mode The sound is not FLAT modified Bass and treble ROG are emphasized CLASSIC Treble is cut a little FLAT The sound is not modified Bass and treble PROGR are emphasized Treble is cut a CLASSIC ittie ACTION Bass is empha sized Vocals and treble oe are emphasized Bass and treble are MAGING emphasized more v Bass and treble are POPS Slightly emphasized Vocals midrange VOCAL tones are emphasized emphasized Setting the clock CD ES66 D Press the lt lt lt or gt gt gt gt button to adjust the hour and then press the MEMORY SET button Ca WA Ca WA ran E gt CO Press the Kt lt lt or gt gt PPI button once to advance the time by 1 hour Hold it down to advance continuously Press the lt lt lt lt or gt gt gt gt button to adjust the minutes and then press the MEMORY SET but
39. onsult the dealer or an experienced radio TV technician for help WARNING FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user s authority to operate this equipment NOTE It is the intent of Sharp that this product be used in full compliance with the copyright laws of the United States and that prior permission be ob tained from copyright owners whenever necessary FOR YOUR RECORDS For your assistance in reporting this unit in case of loss or theft please record below the model number and serial number which are located on the rear of the unit Please retain this information Model number Serial number Date of purchase Place of purchase IMPORTANT SAFETY INSTRUCTIONS 1 Read Instructions All the safety and operating instructions should be read before the product is operated 2 Retain Instructions The safety and operating instructions should be retained for future reference 3 Heed Warnings All warnings on the product and in the operating instructions should be adhered to 4 Follow Instructions All operating and use instructions should be followed 5 Cleaning Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning 6 Attachments Do not use attachments not recommended by the prod uct manufacturer as they may cause hazards 7 Wate
40. r and Moisture Do not use this product near water for ex ample near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like 8 Accessories Do not place this product on an unstable cart stand tripod bracket or table The product may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufac turer or sold with the product Any mounting of the product should follow the manufacturer s instructions and should use a mounting ac cessory recommended by the manufacturer 9 A product and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the product and cart combination to over e turn 10 Ventilation Slots and openings in the cabinet are provided for venti lation and to ensure reliable operation of the product and to protect it from overheating and these openings must not be blocked or cov ered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to 11 Power Sources This product should be operated only from the type of power source indicated on the marking label If you are not sure
41. ral triangle is intended to alert the user to the presence of important operating and main tenance servicing instructions in the lit erature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE Caution use of controls or adjustments or performance of procedures other than those specified herein may re sult in hazardous radiation exposure NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful in terference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to ra dio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be deter mined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected C
42. ten to P S amp D Q 5 Press the gt to start playback Tape play indicator AN Auto power on function PP FR When you press any of the following buttons the unit turns on TAPE C TAPE 1 2 button main unit and remote control The unit 1 lt gt 2 n ni SE turns on and the TAPE function is activated Ce gt button main unit and remote control The unit turns on ON C and playback of the last function starts CD TAPE TUNER STAND BY GAME cp Es600 Recording on a cassette tape CD ES66 WR Various tape functions Before recording Play Press in the stop gt mode Stop Press in the playback fast forward or fast re wind mode When recording important selections make a preliminary test to ensure that the desired material is properly recorded SHARP is not liable for damage or loss of your recording arising from malfunction of this unit The volume and sound controls can be adjusted with no effect on the recorded signal Variable Sound Monitor For recording use only normal tapes Do not use metal or CrO tapes Fast for Press in the playback Erase prevention tab of cassette tapes ward Fast or stop mode l x gewot When recording on a cassette tape make sure that the erase Q prevention tabs are not removed Cassettes have removable n TAPE 2 only i l Q tabs that prevent accidental recording or erasing gt To prote
43. the clock from step 1 0 00 23 59 Note The clock can also be set with the remote control E de 2 Q S L I D D l L i T CD ES600 Listening toa CD CDs CD ES66 This system can also play audio CD R and CD RW discs but can im CD playback not record Some audio CD R and CD RW discs may not be playable due to the 1 Press the ON STAND BY button to turn the power on state of the disc or the device that was used for recording 2 Press the CD button 3 Press the 1 button and within 5 seconds press the OPEN CLOSE button to open the disc tray 1 4 Place the CD on the disc tray 1 label side up Be sure to place 3 8 cm CD in the middle of the disc trays 5 12 cm 3 8 cm Total number of tracks on Total playing time of the the CD whose number is CD whose number is flash 3 S a A O DISC SELECT flashing o CN G2 G3 pal ep will appear Cc C Sas Fre 6 You can place discs on the trays 2 5 by following steps 3 5 G4 GS z IASS T Press the gt lt amp button to start playback CD play indicator ON STAND BY Playback will begin from track 1 on the DISC 1 After that disc fin ishes playing the next disc will automatically play After the last track on the fifth disc is played the CD player stops automatically When there is no CD in one of the disc trays 1 5 the empty tray will be skipped to the next tray with a CD To exchange other CDs w
44. the remote control and the sensor on the unit with a soft cloth Exposing the sensor on the unit to strong light may interfere with operation Change the lighting or the direction of the unit Keep the remote control away from moisture heat shock and vibrations m Test of the remote control Check the remote control after checking all the connections see pages 10 12 Point the remote control directly at the remote sensor on the unit The remote control can be used within the range shown below Press the ON STAND BY button Does the power turn on Now you can enjoy music Remote sensor 8 _ 20 0 2 m Gm ON See STAND BY CD ES600 CD ES66 e ia 2 E Q L D CD ES600 CD ES66 E 2 Q L I D AN General control CLEAR DIMMER cp EQUALIZER MODE C ON STAND BY Q WR To turn the power on Press the ON STAND BY button to turn the power on After use Press the ON STAND BY button to enter the power stand by mode E illumination light control When the power is turned on light illuminates around the display To turn on off the light hold down the CLEAR DIMMER button on the remote control more than 2 seconds E Volume control Main unit operation When the VOLUME control is turned clockwise the volume will increase When it is turned counterclockwise the volume will decrease Remote control operati
45. ton Ca Wa ry In this example the clock is set for the 12 hour AM 12 00 display Press the Kk lt lt or gt gt PPI button once to advance the time by 1 To confirm the time display 2 Press the CLOCK TIMER button When the unit is in the stand by mode 3 Within 10 seconds press the I lt lt lt or gt gt gt gt i button to se Press the CLOCK TIMER button lect CLOCK and press the MEMORY SET button The time display will appear for about 10 seconds When the power is on Press the CLOCK TIMER button Within 10 seconds press the Kt lt lt or gt gt PPI button to display the time The time display will appear for about 10 seconds Press the lt lt lt lt or gt gt PPI button to select 12 hour or 24 Note hour display and then press the MEMORY SET button The CLOCK will appear or time will flash to confirm the time dis play when the AC power supply is restored after a power failure or unplugging the unit If incorrect readjust the clock as follows 7 To readjust the clock z Perform Setting the clock from step 1 If the CLOCK is not AM 12 00 gt The 12 hour display will appear appear in step 3 step 4 for selecting the 12 hour or 24 hour dis ill ki i AM 12 00 PM 11 59 GE ge n eu disptay 1 Clear all the programmed contents Refer to Clearing all the AM 0 00 PM 11 59 memory reset on page 33 for details 0 00 gt The 24 hour display will appear 2 Perform Setting
46. tors cee eee eee ees As an ENERGY STAR Partner SHARP has determined that this product meets the ENERGY STAR guidelines for energy efficiency WR Preparation for Use ENERGY STAR is a U S registered mark System connections Remote control 00 cece ee es WR Basic Operation Groggy General control cece errno eee eee Setting the clock ccc dg erbei ee ege WHY PURCHASE ENERGY STAR LABELED PRODUCTS m CD Playback Many Electrical Electronic Products use energy both when they are on Listening to a CD CDs and when they are off Americans spend more than 3 billion a year on Advanced CD playback energy consumed by home electronic products when they are not in use The new ENERGY STAR labeled models will reduce that en E Radio ergy leakage by up to 75 percent Ultimately this will mean more than 1 billion a year in energy savings for consumers The energy savings will help reduce the burning of fossil fuels and the related carbon dioxide pollution that contributes to global warming e Tape Playback If every American family replaced their electronic equipment with Listening to a cassette tape TAPE 1 or TAPE 2 ENERGY STAR labeled models it would reduce air pollution equiva lent to eliminating more than two million cars m Tape Recording Recording on a cassette tape 020e ee eeee Listening to the radio annnnannnunnnnnnnnnnne Important Instruction By using ENERGY STAR la
47. with the remote control CD ES600 CD ES66 Al L S skas G all Q gt lt CD ES600 CD ES66 Al 2 S sk Ww D Q Q gt lt Timer and sleep operation continued E Sleep operation The radio compact disc and cassette tape can all be turned off automatically 1 Play back the desired sound source 2 Press the CLOCK TIMER button 3 Within 10 seconds press the L a lt lt or gt gt PPI button to select SLEEP and press the MEMO RY SET button 4 Press the lt lt lt lt or gt gt gt gt button to select the time Maximum 3 hours Minimum 1 minute 3 hours 5 minutes gt 5 minute intervals 5 minutes 1 minute gt 1 minute intervals 5 Press the MEMORY SET but ton GLEEP SLEEP tata ta SLEEP will appear 9 I0 me 6 The unit will enter the power stand by mode automatically after the preset time has elapsed The volume will be turned down 1 minute before the sleep op eration finishes To confirm the remaining sleep time 1 While SLEEP is indicated press the CLOCK TIMER button 2 Within 10 seconds press the Kt lt lt or gt gt PP button to select SLEEP X XX X XX is sleep remaining time The remaining sleep time is displayed for about 10 seconds You can change the remaining sleep time while it is displayed by pressing the MEMORY SET button steps 4 5 To cancel the sleep operation Press the ON STAND BY button w
Download Pdf Manuals
Related Search