Home
Sega F355 User's Manual
Contents
1. DIP SW 7 2 SETTING THE ROLL PAPER The 2 red Lamps at the Rear Cabinet back side flash indicating the PAPER END Error under normal operation Prepare the new Roll Paper exclusively used for the product and the Master Key set the Roll Paper perform Printer s initialization to remove the cause of the error Turn off power or enter into the Test Mode to perform the initialization Explanations for setting the Roll Paper in cases of power on and off are given as follows Further when the Roll Paper is set after the Printer Kit is installed performing work with the power off is necessary as the power is turned off when installing the Kit The Roll Paper has Marks indicating position in order to print and cut properly The Mark indicating the end of paper appears at the end of Roll Paper The Printer s Sensor detects the Mark and interprets it as the end of Roll Paper At the beginning of Cabinet s installation the red Lamps light up as the Mark indicating the end of Paper is not detected SETTING THE PAPER WITH THE POWER ON Printer Door 7 Enter into the TEST Mode and PRINTER TEST screen displayed on the monitor ERROR next to the MESSAGE and PAPER END next to the WARNING are displayed on the monitor BPRINTER TEST B MESSAGE ERROR ERROR WARNING PAPER END STATUS COUNTER FIG 7 2a INIT F FEED ASSY
2. LOT 1X9 1919 65 8 www seuservice com 47 OPTIONAL DOLLAR BILL ACCEPTOR THE COIN DOOR ASSEMBLY USED ON F355 challenge DX TYPE COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR ALL NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDATOR S FORWARD MOST Mars 2000 series HOLE POSITION 42 1155 00 MARS VALIDATOR 1 2 5 300 CAP The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series upstacker A 2000 series stacker can be added by simply remov ing the cut out plate This one entry door can be ordered through Happ Controls or one of Happ Controls authorized distributors The part number is 40 6000 10EX The Mars stacker can be obtained through an autherized Mars distibutor Note Your game may have either Happ Controls Coin Door Assembly or the Wells Gardner Coin Door Assembly not shown Happ part number Security Locking Bar Bracket Set Part No 999 0966 Modified Cash Box For use when DBA installed Part No 999 1106 Plastic Cash Box Full Size Part No 999 1177 www seuservice com 48 14 MONITOR 14 1 CAUTIONS AND WARNINGS CONCERNING THE SAFETY FOR HANDLING THE MONITORS WARNING Before handling the monitors be sure to read the following explanations and comply with the caution warning instru
3. 34050 10N3 LOO LLZEXSZ0 6 8 5 dAV T 00 7150 169 oou 00081 068 4 uv HLOOL H3HSVM 00 6 101 068 INGO TEL MANOS 00 2101 068 Posen 00800108 Pos zon 00201068 1HY L 800155 110 050 218 2 262 5015 1 NOILdIH9S10 Dvd JM 46 a a co o e gt in N Ee 5010 3 1910345 9 4000 WOLLO 401 0 NON 0699 966 008 1 THE 31413 68909 1 IVAW 1022 ININ 4 531 08131413 10 0112 5109 d3NQdV5 STI3M www seuservice com 00 00 0 NIOD 0018 BOS 0 20 0 0 DO Lei I Michel cr OL DO LS 90 meat ANd L SZ X p OO LS DD FFDL ZF Do e 0 227 Archie or Meo EF m a E 01 218 2 00 84 Moher 3 gem MIS Dr EF pep Er 82 5 1168 2048 15 52 05 D utn OS Sher 00 01 00 2001 0 00 1022 2 0 16 2 52 85 010 ee DO LEE W09 s oruooddeg MMM dj 4 97ISQOM INO 10009 TI 24010 x q SAUA YOSHIO 901 8104000 44 1607 9S6 LP8
4. Ensure that parts replacement servicing amp inspections and troubleshooting are performed by the location s maintenance man or the serviceman It is instructed herein that particularly hazardous work should be performed by the serviceman who has technical expertise and knowledge The location s maintenance man and serviceman are herein defined as follows Location s Maintenance Man Those who have experience in the maintenance of amusement equipment and vending machines etc and also participate in the servicing and control of the equipment through such routine work as equipment assembly and installation servicing and inspections replacement of units and consumables etc within the Amusement Facilities and or locations under the management of the Owner and Owner s Operators of the product Activities of Location s Maintenance Man Assembly amp installation servicing amp inspections and replacement of units amp consumables as regards amusement equipment vending machines etc Serviceman Those who participate in the designing manufacturing inspections and maintenance service of the equipment at an amusement equipment manufacturer Those who have technical expertise equivalent to that of technical high school graduates as re gards electricity electronics and or mechanical engineering and daily take part in the servicing amp control and repair of amusement equipment Serviceman s Activities Assembly amp
5. 41 www seuservice com 0 Take out a screw to remove the earth wire which is connected to the Clutch Pedal Mechanism side SCREW 1 8 w flat amp spring washers EARTH PHOTO 12 1b 2 Disconnect the connector to remove the Clutch Pedal Disconnect the connector PHOTO 12 1 www seuservice com 42 12 2 VOLUME ADJUSTMENT REPLACEMENT The appropriate value of Crutch Volume is under 30H when released and over COH when stepped on Check Volume values in the TEST mode Since work is performed inside the energized cabinet be very careful so as not to touch undesignated places Touching places not specified can cause electric shock or short circuit ADJUSTING THE VOLUME 7 Loosen 2 screws which secure the Volume Bracket to adjust the gear mesh Tighten the 2 screws 0 In the TEST mode check to ensure that the Volume Values are within the appropriate range and vary smoothly in consistency with the Pedal operation VR BRACKET V R 220 5484 7 220 5373 SCREW 2 M4 X 8 w flat amp spring washers e P PHOTO 12 2 REPLACING THE VOLUME 7 Disconnect the connector from the Volume Q Take out 2 screws to remove the Volume together with the VR Bracket from the Crutch Pedal Mechanism 0 Remove the Volume from the VR Bracket to replace 4 After replacing Volume engage gears and fix VR Bracket G In the TEST mode check to ensure that
6. SECTION A A 83 www seuservice com 5 ASSY FRONT SUB CABI FRI 1001 ITEM NO 101 102 103 104 105 106 107 108 109 110 111 PART NO FRI 1020 FRI 1030 APC 1035 APC 1040 APC 1040 01 STR 1070 FRI 1002 APC 1003 APC 1004 APC 1005 APC 1006 105 5373 FRI 1007 FRI 1008 FRI 1009 DP 1148X DP 1167 105 5169 105 5171 105 5172 117 0062 117 5098 117 5233 253 5396 91 253 5460 01 APC 1009 421 7501 02 FRI 1010 FRI 1011 FRI 1012 FRI 1013 FRI 1014 APC 1079 APC 1090 601 9377 220 5237 92 220 5482 91 220 5574 220 5575 601 5699X 280 5009 01 280 0419 310 5029 D20 601 0460 117 5402 06 270 5052 04 www seuservice com D2 3 DESCRIPTION NOTE AC UNIT SW UNIT FAN MOTOR UNIT METER UNIT 5 OTHERS METER UNIT USA FAN UNIT WOODEN FRONT CABINET BACK DOOR UPPER BACK DOOR LOWER SIDE DOOR L SIDE DOOR R SHIPPING BRKT RED LEG CASTER BRKT A LEG CASTER BRKT B CASTER SPACER PLATE LKG TNG TNG LKG LOCK BRACKET W CHUTE PLATE SINGLE OTHERS CHUTE PLATE DOUBLE USA PLATE LOCK RETAINER TNG RETAINER PLATE PLATE LEG BRACKET BLACK CABINET HANDLE AIR VENT BLACK MONITOR BRKT LOWER STICKER 6 3V 0 15A CONT PNL BRKT C L CONT PNL BRKT CR CONT PNL BRKT L CONT PNL BRKT R FLOOR BRKT CONN PANEL METER CORNER GUARD CASTER FAI 75 ASSY C C 2DR ASSY C C 2DR CAM LOCK W KEYS CAM LOCK MASTER W O KEY LEG ADJUSTER BOLT M16 X 75 CORD CLAMP 21 HARNESS LUG SUMITU
7. FRI 2101 FRI 2102 FRI 2103 FRI 2104 SPG 2504 SPG 2505 SPG 2506 FRI 2105 SPG 2453 ASK 3502 ASK 3503 DYN 1270 SLC 1130 SPG 2454 FRI 2106 350 5448 01 100 5112 601 8966 601 6172 601 6959 601 9173 220 5484 220 5373 310 5029 F20 280 0419 280 5009 01 028 A00408 P 028 A00308 P 065 501250 7 065 S020S0 Z 000 P00408 W 000 P00412 W 030 000612 S 060 F00600 030 000820 S 030 000840 S 068 852216 060 00800 FRI 60064 www seuservice com DESCRIPTION NOTE MECHA BASE BASE LID MOTOR SHAFT SHAFT LOCK PLATE PULLEY 20 S5M PULLEY 60 S5M MOTOR BRKT VR BRKT KEY 4X 4X 40 MOTOR SPACER MOTOR COLLAR STOPPER KEY ADJUST RING MOTOR COLLAR VR BASE SERVO MOTOR 500W NEW BEARING 17 GEAR HOLDER GEAR 48 GEAR 64 TIMING BELT VOL CONT B 5K OHM VOL CONT B 5K OHM SUMITUBE F F 20MM HARNESS LUG CORD CLAMP 21 SET SCR HEX SKT CUP P M4 X 8 SET SCR HEX SKT CUP P M3 X 8 STP RING BLK OZ S12 STP RING BLK OZ 520 M SCR PH W FS M4 X 8 M SCR PH W FS M4 X 12 HEX BLT W S M6 X 12 FLT WSHR M6 HEX BLT W S M8 X 20 HEX BLT W S M8 X 40 FLT WSHR 8 5 22 X 1 6 FLT WSHR M8 WIRE HARN STEERING VOL 104 PEDAL UNIT FRI 2200 SCREW FASTENING TORQUE TO BE 8 178kgf cm 7778 77 LE EN CODE EUR PART NO DESCRIPTION NOTE FRI 2250 ASSY ACCEL amp BRAKE 2 FRI 2300 ABSORBER UNIT 3 FRI 2201 FOOT REST FRI 4 FRI 2204 PEDAL BASE 201 030 000825 SB HEX BLT W S BLK M8
8. K AWG18 UL1015 I AWG20 UL1007 None AWG22 UL1007 www seuservice com 144 Warranty Your new Sega Product is covered for a period of 90 days from the date of shipment This certifies that the Printed Circuit Boards Power Supplies and Monitor are to be free of defects in workman ship or materials under normal operating conditions This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating condi tions No other product in this machine is hereby covered Sellers sole liability in the event a warranted part described above fails shall be at its option to replace or repair the defective part during the warranty period For Warranty claims contact your Sega Distributor Should the Seller determine by inspection that the product was caused by Accident Misuse Ne glect Alteration Improper Repair Installation or Testing the warranty offered will be null and void Under no circumstances is the Seller responsible for any loss of profits loss of use or other dam ages This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied Under no circumstance shall it extend beyond the period of time listed above SEGA ENTERPRISES INC USA 45133 Industrial Drive Fremont CA 94538 415 701 6580 phone 415 701 6594 fax
9. WIRE HARN CP WIRE HARN MAIN SW WIRE HARN FILTER IN WIRE HARN FILTER OUT WIRE HARN EARTH 05 0100MM WIRE HARN EARTH 05 0120MM WIRE HARN EARTH ID5 0700MM 87 www seuservice com 7 SW UNIT FRI 1030 DEMAG LEFT CENTER RIGHT SPEAKER 1 1031 2 421 11127 101 220 5179 102 509 5028 103 601 0042 104 310 5029 D20 105 601 0460 301 APC 60087 302 600 6609 32 303 FRI 60089 www seuservice com SERVICE sy DESCRIPTION NOTE SW BRACKET STICKER SW UNIT VOL CONT B 5K OHM SW PB 1M KNOB 22 MM SUMITUBE F D 20 MM PLASTIC TIE BELT 100 MM WIRE HARN DEMAG WIRE HARN TEST amp SERVICE WIRE HARN SOUND VOL 88 FAN MOTOR UNIT APC 1035 ZF AXIAL FLOW FAN 50 60HZ M SCR PH W FS M3 X 12 DESCRIPTION FAN MOTOR BRKT FAN GUARD FLG NUT M3 APC 1036 260 0011 02 601 8543 000 P00312 W 050 F00300 101 102 201 202 9 METER UNIT 8 APC 1040 ITEM NO PART NO DESCRIPTION NOTE 1 1041 5 2 421 6591 16 STICKER COIN METER 100 101 220 5643 01 MAG CNTR DCSV 6P WH MZ 674 D04 www seuservice com 90 9 METER UNIT T APC 1040 01 ITEM NO 1 2 101 102 PART NO APC 1042 421 6591 01 220 5643 01 220 5643 02 5 8 DESCRIPTION NOTE METER BRKT T STICKER COIN METER MAG CNTR DCSV WH MZ 674 D04 MAG CNTR DCSV YE MZ 674 D05 91 www seuservice com FAN UNIT
10. installation and repair amp adjustments of electrical electronic and mechanical parts of amusement equipment and vending machines LISTED 3K92 AMUSEMENT MACHINE 1 HANDLING PRECAUTIONS WARNING IMPORTANT When installing or inspecting the machine be very careful of the following points and pay attention to ensure that the player can enjoy the game safely Non compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine Before performing work be sure to turn power off Performing the work without turning power off can cause an electric shock or short circuit In the case work should be performed in the status of power on this manual always states to that effect To avoid electric shock or short circuit do not plug in or unplug quickly To avoid electric shock do not plug in or unplug with a wet hand Do not expose Power Cords and Earth Wires on the surface floor passage etc If exposed the Power Cords and Earth Wires are susceptible to damage Damaged cords and wires can cause electric shock or short circuit To avoid causing a fire or electric shock do not put things on or damage Power Cords When or after installing the product do not unnecessarily pull the power cord If damaged the power cord can cause a fire or electric shock In case the power cord is damaged ask for replacement thr
11. is slight and the paper cutting may not be done Before executing the POSITION SET the paper position can be adjusted by executing F FEED or B FEED in the PRINTER TEST mode 2 Exit from the TEST Mode 13 Push the ASSY PRINTER up to the point the PRINTER reaches the Securing Part in the innermost of the unit 3 Lock the Printer Door to secure SETTING THE PAPER WITH THE POWER OFF 7 Turn off power Unlock with the Master Key and remove the Printer Door 0 Draw ASSY Printer toward you 4 Pull up Head Up Lever 5 Take out the roll shaft from the Printer 6 Pass the shaft through the core of the new Roll Paper 7 Install the roll shaft in which the paper is inserted into the unit Make sure to put the Roll Paper on to the correct position BPRINTER TESTE MESSAGE PRINTER INIT ERROR WARNING STATUS COUNTER gt INIT F FEED B FEED POSITION SET BPRINTER TEST B MESSAGE NOW PRINT ING ERROR WARNING STATUS B FEED gt POSITION SET In case that the paper tip comes out in excess of the exit slot Paper is cut after Printer feeds Paper one page Printer Door FIG 7 2g www seuservice com Roll shaft New Roll Paper when setting the new Paper for the first time gt Head Up Lever lt gt Note that this Roll Paper gt holder will not be seen N FIG 7 2h Insert the paper tip in to the Roll Paper insertion
12. 100MM U NUT M8 HEX BLT W S M8 X 16 FLT WSHR M8 HEX BLT W S M6 X 16 FLT WSHR M6 SCR PH WS MAX 6 FLT WSHR M4 SCR PH W S 8 WIRE HARN EXT PADDLE TUBE WIRE HARN EARTH ID5 0500MM WIRE HARN BRAID T5 5 5 0SOOMM 100 ASSY PADDLE SHIFT FRI 2050 D 1 2 Details of PART B x lt 2 18 SCREW FASTENING TORQUE BE 101 www seuservice com ASSY PADDLE SHIFT FRI 2050 D 2 2 ITEM NO PART NO 1 FRI 2051 2 FRI 2052 3 FRI 2053 4 FRI 2054 5 SLC 1314 6 SLC 1315X 7 SLC 1316 8 117 0141 9 310 0012 10 FRI 2056X 11 FRI 2057X 101 509 5387 103 280 0419 104 601 0460 201 000 P00408 S 202 000 P00316 W 203 000 F00512 204 000 F00525 205 050 U00500 206 012 P00416 301 FRI 60086 www seuservice com DESCRIPTION NOTE BOSS SHIFT PLATE SPRING LID SW BRKT PIVOT PLUNGER COMP SPRING PLATE LOCK PAPER INSL GUARD BLOCK A GUARD BLOCK B SW MICRO TYPE HARNESS LUG PLASTIC TIE BELT 100MM SCR PH W S 8 M SCR PH W FS M3 X 16 M SCR M5 X 12 M SCR FH 5 X 25 U NUT M5 TAP SCR 2 PH 4 X 16 WIRE HARN PADDLE SHIFT 102 STEERING MOTOR UNIT FRI 2100 D 1 2 SECTION A A 103 www seuservice com STEERING MOTOR UNIT FRI 2100 0 2 Q D 101 102 103 104 105 106 107 108 109 110 201 202 203 204 205 206 207 208 209 210 211 212 PART NO
13. CABINET 1 Install the Joint Bracket L and 2 Joint Bracket R to the both sides of Front Cabinet and 2 Joint Pipes to the inside At this time temporarily install the Joint Brackets L and R JOINT BRACKET R JOINT PIPE Hexagon Bolt 2 each M8 X 30 w spring washer flat washer used Connect the wiring from the Front Connect the Earth Cabinet to the Rear Cabinet REAR CABINET side SCREW 1 M4 X 8 w flat amp spring washers FRONT CABINET side Conn FIG 6 1b www seuservice com 12 0 Insert the Front Cabinet s Joint pipes into the Rear Cabinet s square holes to fit both cabinets tight Be sure to perform this work by 2 or more workers Also be careful so as not to pinch the wiring 4 Secure the joint portion of the Cabinets with 6 Hexagon Bolts Firmly secure the Joint Brackets L amp R respectively 5 By using Joint Plate Center secure the joint portion of the Cabinets with 4 Truss screws and Hexagon Bolts a JOINT BRACKET R HEXAGON BOLT 2 each M8 X 20 w spring washer flat washer used HEXAGON BOLT 2 lt M8 X 30 w spring washer JOINT PLATE CENTER Ze TRUSS SCREW 4 M4 X 16 HEXAGON BOLT 2 each M8 X 30 spring washer flat washer used JOINT BRACKET L FIG 6 1 13 www seuservice com INSTALLING THE CENTER ROOF AND THE BILLBOARD 7 Put the Center Roof on its insta
14. CONN HIGH T CE CORD CLAMP 21 HEX BLT BLK W S M6 X 30 M SCR W FS 16 HEX BLT W S M6 X 30 FLT WSHR M6 SCR NAIL THH STNLS 1 5 X 16 M SCR TH CRM 16 SCR W FS M4 X 30 HEX NUT M16 M SCR PH W S M4 X 8 FLT WSHR M4 ASSY WIRE REAR WIRE HARN EXT AC REAR WIRE HARN CENTER TOWER AC WIRE HARN CENTER TOWER DC WIRE HARN EARTH ID5 0600MM WIRE HARN EARTH ID5 1000MM 112 23 ASSY WIRE REAR FRI 6003 ASSY WIRE REAR is comprised of the following wire harnesses An ASSY DRG is unavailable ITEM NO PART NO DESCRIPTION NOTE 101 601 0460 PLASTIC TIE BELT 100 MM 301 FRI 60065 WIRE HARN EXT REAR CTRL B 302 FRI 60066 WIRE HARN EXT SHIFT LOCK B 303 FRI 60067 WIRE HARN EXT SEAT SP B 304 FRI 60070 WIRE HARN EXT BASS SP 305 FRI 60073 WIRE HARN EXT BRAKE LAMP B 113 www seuservice com ASSY 6SPEED SHIFTER FRI 2150 1 4 i gale D 1 3 8 ED E du 103 28 o 9 5m 1 1 an www seuservice com 114 ASSY 6SPEED SHIFTER FRI 2150 D 2 3 ITEM NO Q EUA 101 102 103 104 105 106 107 108 109 PART NO 2151 2152 2153 2154 FRI 2155 FRI 2156 SPG 2159 FRI 2158 FRI 2159 FRI 2160 FRI 2161 FRI 2162 FRI 2163 FRI 2164 FRI 2165 FRI 2166 FRI 2167 FRI 2168 FRI 2169 FRI 2170 2171 2172 2173 2174 2
15. Head Up Lever and turn on power The Printer performs automatic feeding and cutting of the paper 1 Put the ASSY Printer and lock the printer door to secure 25 www seuservice com 7 4 COUNTERMEASURES AGAINST PAPER JAM Prepare a Master Key and scissors or a knife for eliminating the warped wrinkled paper due to paper jam To perform the following work turning off power is necessary for 2 reasons One is that performing work on the energized Cabinet may cause hands and fingers to be injured due to unexpected move of the cutter or the motor To avoid such an unforeseen accident be sure to turn off power before performing work The other reason is that in order to remove the cause of error from the Printer turning power off is necessary Be sure to remove the cause of error to make the Printer function properly 1 Turn off power 2 Unlock with the Master Key and remove the Printer Door Draw the ASSY Printer toward you Auto Cutter 4 Pull up Head Up Lever G Push down the Cutter Lever and open the Auto Cutter 6 Remove the jammed paper Head Up Lever Cutter Lever 7 Eliminate the warped wrinkled paper due to the paper jam At this time after eliminating the paper any portion can come to the tip as the Printer automatically adjusts the Paper position by feeding and cutting the Paper FIG 7 4 b Lift the Auto Cutter and lock 9 Insert the paper tip in to the roll paper insertio
16. PHOTO 10 1 a M4 X 12 large washers used www seuservice com 36 2 Disconnect connector G Take out 4 Hexagon Bolts HEXAGON BOLT 4 M8 X 40 w flat amp spring washers isconnect the connector PHOTO 10 1b 6 SPEED SHIFT PHOTO 10 1 6 Lift the 6 speed Shift vertically At this time use care so as not to hang the wiring or hit the other parts Disconnect 2 connectors to remove the 6 speed Shift PHOTO 10 1d Disconnect the connector 37 www seuservice com 10 2 REPLACING THE SWITCH In case 6 speed Shift operability is poor malfunction of or damage to the Microswitch of Mechanism can be considered The 6 speed Shift has 4 Microswitches Be sure to check which Switch malfunctions prior to performing work 1 Remove 6 speed Shift as per procedure 10 1 SCREW 2 M2 3 X 10 w flat amp spring washers Q Disconnect the wiring connected to the Microswitch 0 Take out 2 screws to replace the Microswitch 4 Adjust Microswitch s actuator to an angular position so as not to touch the Switch when operating the Shift Lever 5 Fasten 2 screws to secure the Microswitch MICROSWITCH 509 5636 PHOTO 10 2 Check to ensure that the Switch SCREW 2 goes ON and OFF in consistency M2 3 X 10 w flat amp spring washers with the operation MICROSWITCH i 509 5636 TM A P 08 F E PHOTO 10 2b www seuservice com 38 11 ACCELERATOR amp BR
17. PLASTIC TIE BELT 100 MM 301 600 6972 0700 WIRE HARN EARTH ID5 0700MM 302 600 6972 1800 WIRE HARN EARTH 105 1800MM 303 600 6972 2200 WIRE HARN EARTH ID5 2200MM 304 600 6972 2250 WIRE HARN EARTH ID5 2250MM 305 600 6972 3000 WIRE HARN EARTH ID5 3000MM 93 www seuservice com ASSY MONITOR CENTER APC 1100 ITEM NO 101 102 103 104 105 106 201 202 PART NO APC 1101 APC 1152X 280 5112 280 5113 APC 1086 200 5710 280 5275 5 10 280 5009 01 280 5185 6 601 6231 020 601 6231 D045 050 F00600 000 P00312 W 600 6972 1600 www seuservice com 105 106 DESCRIPTION MONITOR BRKT UPPER MONITOR HOLD UPPER BUSH FOR TV COLLAR FOR TV MONITOR BD BASE ASSY CLR DSPL 29AUTO MS 2931 S CORD CLAMP SR10 CORD CLAMP 21 SPACER TUBE L 6 EDGING NEW TYPE EDGING NEW TYPE FLG NUT M6 SCR PH W FS M3 X 12 WIRE HARN EARTH 05 1600 94 5 AT 9 15 ASSY MONITOR LEFT APC 1150 D 1 2 Details of PART A 95 www seuservice com 15 ASSY MONITOR LEFT APC 1150 ITEM NO 1 ON Q D 101 102 103 104 105 106 107 201 202 203 204 205 206 207 208 PART NO APC 1151 APC 1152X APC 1153X APC 1154X APC 1155X APC 1156X APC 1157X APC 1054 APC 1159X APC 1058X APC 1160 280 5112 280 5113 APC 1083 601 10562 0170 601 10562 0580 APC 1086 200 5710 280 5275 SR10 280 500
18. Shift Lever 6 Fasten 2 screws to secure the Microswitch 7 Check to ensure that the Switch goes ON and OFF in consistency with the operation MICROSWITCH 509 5387 PHOTO 9 3 b 35 www seuservice com 10 6 SPEED SHIFT Before starting to work ensure that the Power SW is OFF Failure to observe this can cause electric shock or short circuit WARNING Use care so as not to damage wirings Damaged wiring can cause electric shock or short circuit Do not touch undesignated places Touching places not designated can cause electric shock or short circuit This work should be performed by the Location s Maintenance Man or Serviceman Performing work by non technical personnel can cause electric shock hazard When performing work such as parts replacement other than those specified in this manual be sure to contact where you purchased the product from Confirm the work procedures and obtain precautions from where you purchased the product from prior to performing work Inappropriate parts replacement and or installation with erroneous adjustment can cause an overload or the parts to come into contact resulting in an electric shock a short circuit and a fire 10 1 REMOVING THE SHIFT LEVER off power Q Take out 4 screws securing the EFFECT Switch 0 Take out 5 Truss screws which secure the Console Cover TRUSS SCREW 4 12 CONSOLE COVER EFFECT SWITCH TRUSS SCREW 5
19. X 25 202 060 00800 0 FLT WSHR BLK M8 203 050 H00800 HEX NUT M8 204 060 500800 SPR WSHR M8 205 060 F00800 FLT WSHR M8 105 www seuservice com 1 ASSY ACCEL amp BRAKE FRI 2250 D 1 2 www seuservice com 106 21 ASSY ACCEL amp BRAKE FRI 2250 D 2 2 ITEM NO D 101 102 103 104 105 201 202 203 204 205 206 207 208 209 210 PART NO SPG 2201 2251 2252 2257 FRI 2253 SPG 2206 SPG 2207 FRI 2254 SPG 2210 FRI 2255 SPG 2214 SPG 2216 FRI 2256 SPG 2219 SPG 2220 FRI 2258 FRI 2259 100 5263 220 5484 220 5373 601 7944 310 5029 F 15 280 0419 028 A00304 P 020 000520 0Z 000 P00420 000 P00508 W 000 T00408 0C FAS 450005 000 P00405 FAS 000001 060 F00400 000 P00412 W FRI 60088 DESCRIPTION NOTE BASE ACCEL PEDAL FRI BRAKE PEDAL FRI ACCEL SPRING FRI BRAKE SPRING FRI SHAFT ACCEL GEAR NEUTRAL STOPPER FRI VR PLATE ACCEL VR PLATE BRAKE FRI STOPPER COVER VR COVER FRI GEAR STAY WSHR STOPPER PLATE GEAR SPACER BEARING 12 VOL CONT B 5K OHM VOL CONT B 5K OHM GEAR 15 SUMITUBE F F 15MM HARNESS LUG SET SCR HEX SKT CUP P M3 X 4 HEX SKT H CAP SCR BLK M5 X 20 M SCR PH M4 X 20 M SCR W FS 5 X 8 M SCR TH CRM M4 X 8 SPR PIN BLK OZ 6 X 10 SCR PH M4 X 5 M SCR TH CRM M3 X 6 FLT WSHR M4 SCR PH W FS 12 WIRE HARN ACCEL amp BRAKE 107 www seuservice com 02 ABSORBER UNIT FRI 2300 I
20. fire electric shock injury and or malfunctioning Places subject to rain or water leakage or places subject to high humidity in the proximity of an indoor swimming pool and or shower etc Places subject to direct sunlight or places subject to high temperatures in the proximity of heating units etc Places filled with inflammable gas or vicinity of highly inflammable volatile chemicals or hazardous matter Dusty places Sloped surfaces Places subject to any type of violent impact Vicinity of anti disaster facilities such as fire exits and fire extinguishers The operating ambient temperature range is from 5 to 40 C Only in the case a projector is employed the temperature range is from 5 C to 30 C LIMITATIONS OF USAGE REQUIREMENTS WARNING Be sure to check the Electrical Specifications Ensure that this product is compatible with the location s power supply voltage and frequency requirements A plate describing Electrical Specifications is attached to the product Non compliance with the Electric Specifications can cause a fire and electric shock This product requires the Breaker and Earth Mechanisms as part of the location facilities Using them in a manner not independent can cause a fire and electric shock Ensure that the indoor wiring for the power supply is rated at 15A or higher AC single phase 100 120V area and 7A or higher AC 220 240V area Non compliance with the Electri
21. push it from side directions and move it by 2 or more persons for safety Do not insert the fork to places other than designated when using a Forklift to transport the machine Failure to observe this could cause falling down and injury resulting from falling down Do not push glass made or plastic parts Failure to observe this may damage parts and cause injury due to fragments resulting from damage When transporting the product in places with steps disassemble into each unit before transporting Inclining the product in an as is assembled condition or placing the cabinet in places with steps can damage the unit s joining portions To protect surface do not directly apply a rope to the surfaces of product Use protective materials to the places the rope is applied to In the case the cabinet is separated into the front and rear portions do not push the upper rear part of the front cabinet 27 www seuservice com When transporting the product in places with steps or step like differences in grade disassemble into each unit before transporting y EN S 7 A BSS WW Have casters make contact with the floor FIG 8b SS SENN S L SS VA S N f M NN zg av 3 75 SS S 5 Z
22. set Part Number 601 10735 01 consists of 4 rolls of exclusively used paper and a Cleaning Pen PART NUMBER 601 10735 01 DESCRIPTION PAPER FOR F355 ENG 7 1 OPERATION WITH THE PRINTER ATTACHED The Printer which prints Player s Driving Data and the GAME BOARD do not keep the data to be printed When PRINTING CAN NOT BE DONE is displayed or the PRINTER is set to OFF in the Test mode printing can not be done as the product does not have such system as printing out the data at a later operation Therefore as for the printing instruct the Player to pay attention to the following Although YES is selected to the PRINT OUT question displayed on the monitor printing can not be done if a credit worth coin is not inserted within the time limit Such credit coin as inserted after the time limit is regarded as a game play credit If the Printer malfunctions such as a paper jam occurred during printing the printing for the Driving Data can not be done as neither the Printer nor the ROMs on the GAME BOARD keeps the data When PRINTING CAN NOT BE DONE is displayed or the PRINTER is set to OFF in the Test mode printing can not be done as the product does not have such system as printing out the data at a later execution www seuservice com 20 DIP SW SETTING SWI SW2 The Printer has 2 DIP Switches To avoid Setting at the time of shipment malfunctioning use the Switches as adjusted at the time of shipment
23. the Volume Values are within the appropriate range and vary smoothly in consistency with the Pedal operation 43 www seuservice com 12 3 GREASING Be sure to use the designated grease Using undesignated grease can cause parts damage IMPORTANT Once every 3 months apply greasing to the Spring and Gear mesh portion For spray greasing use GREASE MATE PART No 090 0066 VOLUME GEAR MESH PORTION PHOTO 12 3 www seuservice com 44 13 COIN SELECTOR If the coin is not rejected when the REJECT button is pressed open the coin chute door and open the selector gate After removing the jammed coin put a normal coin in and check to see that the selector correctly functions CLEANING THE COIN SELECTOR IMPORTANT Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry Never apply machine oil etc to the Coin Selector After cleaning the Coin Selector insert a regular coin in the normal working status and ensure that the Selector correctly functions The coin selector should be cleaned once every 3 months When cleaning follow the procedure below Turn the power for the machine OFF Open the coin chute door Open the gate and dust off by using a soft brush made of wool etc Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry
24. the surfaces of the PROTECT RUBBER on the Seat Rail or any excess grease fi FIG 16 CLEANING THE CABINET SURFACES If the Cabinet is badly stained use a cloth which is dipped in the chemical detergent liquid diluted with water and then squeezed dry Do not use such solvents as alcohol thinner benzine etc or abrasives bleaching agents and or chemical dustcloth as these can damage cabinet surface finish 67 www seuservice com 17 TROUBLESHOOTING In case a problem occurs first check wiring connector connections In order to prevent electric shock and short circuit be sure to turn power off before performing work WARNING Be careful so as not to damage wirings Damaged wiring can cause electric shock or short circuit After removing the cause of the functioning of the Circuit Protector reinstate the Circuit Protector Depending on the cause of the functioning using the Circuit Protector as is without removing the cause can cause generation of heat and fire hazard TABLE 17a PROBLEMS CAUSE COUNTERMEASURES When the main SW ThepowerisnotON power is not ThepowerisnotON Firmly insert the plug into the outlet insert Firmly insert the plug into the outlet plug into the outlet is turned ON the machine is not Incorrect power source voltage Make sure that the power supply voltage are activated correct AC UNIT CIRCUIT PROTECTOR First remove the cause of overc
25. when replacing the Fluorescent Lamp Be sure to use lamps of the designated rating Using lamps of undesignated rating can cause a fire or malfunctioning To perform work safely and securely be sure to prepare a step which is ina secure and stable condition Performing work without using the step can cause violent falling down accidents When handling glass made or plastic parts use care Failure to observe this may damage parts and cause injury due to fragments resulting from damage This product employs the total of 4 fluorescent lamps and the total of 2 slim lamps no electrode lamps 57 www seuservice com SEAT LEFT amp RIGHT 1 Turn off power 2 Take out 5 Truss screws from the left hand side and 4 Truss screws from the right hand side of the seat facing the monitor 0 Remove the Sash 4 Remove FL Cover Side G Replace the Fluorescent Lamp SASH TRUSS SCREW 4 9 12 H TRUSS SCREW 5 12 A LEFT RIGHT FIG 15 a FLUORESCENT LAMP 32W FL COVER SIDE 390 5251 32 01 GLOW BULB 390 5638 5P www seuservice com 58 BILLBOARD Tum off power Take out 4 Truss screws in total 0 Remove 2 Bushes and the Plate Holder 4 Remove the FL Plate At this time be sure to keep _TRUSS SCREW 2 t
26. 0 311 312 PART NO FRI 4301 839 1147 DRT 4502 421 7914 250630 FRI 4302 421 11128 601 10369 560 5406 V 117 5225 514 5086 6300 514 5084 310 5029 F20 260 001 1 02 601 8543 280 5009 01 280 0419 838 13604 220 5179 601 0042 310 5029 D20 000 P00312 W 050 F00300 000 P00412 W 011 P00325 011 T03516 011 F00310 011 T03512 011 F00312 FRI 60028 FRI 60029 FRI 60030 FRI 60031 FRI 60032 FRI 60033 FRI 60034 FRI 60035 FRI 60036 FRI 60037 FRI 60038 FRI 60091 www seuservice com DESCRIPTION NOTE WOODEN AUDIO BASE AUDIO MIX BD UL FAN MOTOR BRKT STICKER AC 250V 6 3A VR BRKT STICKER AMP VOL STEREO PWR AMP 47 XFMR 100 23V5A X 2 TERMINAL 3P 20A FUSE S B 6300MA 250V HBC CE FUSE HOLDER F 60B W F 60 SUMI TUBE FF 20MM AXIAL FLOW FAN 50 60HZ FAN GUARD CORD CLAMP 21 HARNESS LUG BASS AMP 50W X 1 VOL CONT B 5K OHM KNOB 22 MM SUMITUBE F D 20 MM SCR W FS M3 X 12 FLG NUT M3 SCR W FS 12 TAP SCR PH 3 X 25 TAP SCR TH 3 5 X 16 TAP SCR FH 3 X 10 TAP SCR TH 3 5 X 12 TAP SCR 1 FH 3 X 12 WIRE HARN AMP AC IN WIRE HARN AMP FAN WIRE HARN AMP XFMR IN WIRE 47 AMP AC IN WIRE HARN BASS AMP AC IN WIRE HARN SOUND MIX IN WIRE HARN SOUND MIX OUT WIRE HARN SOUND OUT WIRE HARN AMP VOL IN WIRE HARN BASS SP OUT WIRE HARN SEAT SP OUT WIRE HARN BASS VOL 142 ASSY SERVO DRV BASE FRI 4400 ITEM NO 1 2 101 102 103 104 201 202 203 204 3
27. 00412 0B 030 000840 SB 060 F00400 000 P00408 W FAS 200013 011 T03512 600 6972 0600 D 3 3 DESCRIPTION NOTE BLIND PLATE L BLIND PLATE R CUSHION SPONGE 30 COUPLING MJT 40K BL 16 20 M SCR TH BLK M4X 8 M SCR PH W FS 16 M SCR TH M4 X 10 BLK M SCR TH CRM 10 M SCR TH BLK M4 X 16 TMP PRF SCR BH BLK M8 X 30 HEX SKT H CAP SCR BLK 0Z M8 X 20 HEX BLT BLK W S M6 X 30 HEX BLT W S BLK M8 X 20 HEX BLT W S BLK X 30 HEX BLT W S BLK M8 X 50 WING BLT X 25 FLG NUT M6 FLT WSHR BLK M8 SPR WSHR BLK M8 FLT WSHR 4 4 16 1 6 FLT WSHR BLK 4 4 16 X 1 6 FLT WSHR CRM 4 4 16 X 1 6 FLT WSHR BLK 6 5 20 X 1 6 FLT WSHR BLK 8 5 22 X 1 6 M SCR TH BLK M4 X 12 HEX BLT W S BLK M8 X 40 FLT WSHR M4 M SCR PH W FS M4 X 8 HEX SKT H CAP SCR CRM M4 X 16 TAP SCR TH 3 5 X 12 WIRE HARN EARTH ID5 0600MM 79 www seuservice com 3 ASSY REAR CABINET FRI 3000 D 1 2 VE U 18868 197 www seuservice com 80 3 ASSY REAR CABINET FRI 3000 ITEM NO Q EUA 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 PART NO FRI 3001 FRI 2150 FRI 3050 FRI 3060 FRI 3100 FRI 3150 FRI 3200 FRI 3300 FRI 3400 FRI 0500 FRI 3030 FRI 3031 FRI 3014 FRI 3015 FRI 3017 FRI 3018 FRI 3156X FRI 3020 FRI 3034 FRI 3055 130 5196 030 000816 S 030 000830 S 060 F00800 030 000830 SB 008 B00830 0B 060 F00800 0B
28. 01 Ma PHOTO 151 65 www seuservice com 16 PERIODIC INSPECTION TABLE The items listed below require periodic check and maintenance to retain the performance of this machine and to ensure safe business operation Be sure to check once a year to see if Power Cords are damaged the plug is securely inserted dust is accumulated between the Socket Outlet and the WARNING Power Plug etc Using the product with dust as is accumulated can cause fire and electric shock hazards Periodically once a year request the place of contact herein stated or the Distributor etc where the product was purchased from as regards the internal cleaning Using the product with dust as is accumulated in the interior without cleaning can cause a fire or accident Note that cleaning the interior parts can be performed on a pay basis TABLE 16 PRINTER OPTIONAL 2 of the printer head After a roll of paper is exhausted COINSELECTOR ChakcoINSWa Comments we n POWER SUPPLY PLUG Inspection and cleaning www seuservice com 66 REAR CABINET Greasing to Seat Rail Portion Move the Seat to the rearmost portion and apply spray greasing to the portion shown at the right once every 3 months by using NOK KLUBER L60 or GREASE MATE SEGA PART No 090 0066 After greasing move the Seat a few times forward and backward so as to allow the grease to be applied all over uniformly Be sure to wipe grease which attaches to
29. 01 302 303 304 305 306 FRI 4401 FRI 4402 838 13843 838 12912 01 280 5009 01 601 0460 000 P00412 W 000 P00312 W 011 P00325 011 F00310 FRI 60039 FRI 60040 FRI 60041 FRI 60042 FRI 60043 FRI 60044 DESCRIPTION NOTE WOODEN BASE SERVO SERVO DRV BRKT DRIVE BD FRI SERVO MOTOR DRIVE BD NEW CORD CLAMP 21 PLASTIC TIE BELT 100 MM SCR W FS 12 M SCR PH W FS M3 X 12 TAP SCR PH 3 X 25 TAP SCR FH3 X 10 WIRE HARN SERVO AC IN WIRE HARN DRV DC IN WIRE HARN DRV CTRL WIRE HARN SERVO CTRL WIRE HARN SERVO ENC WIRE HARN SERVO PWR 143 www seuservice com 21 WIRE COLOR CODE TABLE THE WIRE COLOR CODE is as follow A PINK B SKY BLUE C BROWN D PURPLE E LIGHT GREEN Wires other than those of any of the above 5 single colors will be displayed by 2 alphanumeric characters 1 RED 2 BLUE 3 YELLOW 4 GREEN WHITE 7 ORANGE 8 BLACK 9 GRAY If the right hand side numeral of the code is 0 then the wire will be of a single color shown by the left hand side numeral see the above Note 1 Ifthe right hand side alphanumeric is not 0 that particular wire has a spiral color code The left hand side character shows the base color and the right hand side one the spiral color lt Example gt SL WHITE RED RED WHITE Note 2 The character following the wire color code indicates the size of the wire U AWG16 UL1015
30. 0312 000 T00412 0B FRI 60076 FRI 60077 www seuservice com 2 2 DESCRIPTION NOTE SIDE TOWER R SIDE FL COVER R SASH FRONT R WOODEN BASE FOR BRST FL HOLDER STICKER FL32W STICKER W POWER OFF ENG STICKER W HIGH TEMP ENG GLOW amp BALLAST UNIT 1P 32W FL 32WEX W CONN LOW W O G amp B SCR TH BLK 25 TAP SCR TH 3 12 M SCR TH BLK M4 X 12 WIRE HARN SIDE TOWER INV IN WIRE HARN SIDE TOWER R FL 120 ASSY CORNER LIGHT L FRI 3100 D 1 2 121 www seuservice com ASSY CORNER LIGHT L FRI 3100 ITEM NO e o0 u amp Ut 101 102 103 104 105 201 202 204 205 206 301 302 PART NO FRI 3151 FRI 3152 FRI 3153X FRI 3154 FRI 3155 440 WS0002XEG FRI 3158 FRI 3159 440 CS0180 EG 400 5414 390 6651 601 7467 310 5047 6H0014 601 0460 000 T00408 0B 000 00412 0 030 000816 SB 000 P00312 W 068 441616 0C FRI 60082X FRI 60083 www seuservice com 2 2 DESCRIPTION NOTE CORNER LIGHT BOX CORNER LIGHT LID LID EDGE PACKING CORNER REFRECTOR LIGHT HOLDER STICKER W POWER OFF ENG LIGHT HOLDER BUSH LIGHT HOLDER SPACER STICKER C KEEP OUT ENG INVERTER FIP24 12N UX EXT ELECTRODE CFX12AYG 36H L LOCK BK VINYL TUBE 6H 0014CM PLASTIC TIE BELT 100 MM M SCR TH BLK M4 X 8 M SCR TH CRM M4 X 12 HEX BLT W S BLK M8 X 16 SCR W FS M3 X 12 FLT WSHR CRM 4 4 16 X 1 6 WIRE HARN CORNER L AC WIRE HARN BRAKE LAMP L 122 ASSY CORNER LIGHT R FRI 3150 D 1
31. 068 852216 0B 000 00412 0 068 441616 0C 000 T00412 0B 068 441616 0B 000 P00416 W 030 000840 S 000 T00416 0B 030 000850 SB 050 H00400 060 S00400 060 F00400 000 P00408 S FRI 60071 D22 DESCRIPTION NOTE ASSY REAR SUB CABI ASSY 6SPEED SHIFTER ASSY SIDE TOWER L ASSY SIDE TOWER ASSY CORNER LIGHT L ASSY CORNER LIGHT R ASSY REAR ROOF ASSY SEAT ASSY EFFECT SW ASSY BILLBOARD SHIFT BRKT L SHIFT BRKT R SASH REAR REAR FL COVER CONSOLE BASE CONSOLE COVER CORNER PLATE WOOFER HOLDER REAR WINDOW REAR SASH PACKING WOOFER 4 80 HEX BLT W S M8 X 16 HEX BLT W S M8 X 30 FLT WSHR M8 HEX BLT W S BLK M8 X 30 TMP PRF SCR BH BLK M8 X 30 FLT WSHR BLK M8 FLT WSHR BLK 8 5 22 X 1 6 M SCR TH CRM M4 X 12 FLT WSHR CRM 4 4 16 X 1 6 M SCR TH BLK M4 X 12 FLT WSHR BLK 4 4 16 X 1 6 M SCR PH W FS M4 X 16 HEX BLT W S M8 X 40 M SCR TH BLK 16 HEX BLT W S BLK M8 X 50 HEX NUT M4 SPR WSHR M4 FLT WSHR M4 M SCR PH W S M4 X 8 WIRE HARN SUB WOOFER IN 81 www seuservice com 4 ASSY BILLBOARD FRI 0500 NOTE M8 TAMPER FASTENING TORQUE TO 30kgf cm ITEM NO PART NO DESCRIPTION NOTE 1 FRI 0501 BILLBOARD FRI 0502 BILLBOARD LEG 201 008 B00830 0B TMP PRF SCR BH BLK M8 X 30 202 068 852216 0B FLT WSHR BLK 8 5 22 X 1 6 www seuservice com 82 5 ASSY FRONT SUB CABI FRI 1001 D 1 3 T8kd M8 BOLT FASTENING TORQUE 1 78
32. 100CM WIRE HARN PRINTER DC 85 www seuservice com 6 AC UNIT FRI 1020 1 E www seuservice com 86 D 1 2 6 AC UNIT FRI 1020 101 102 103 104 105 106 107 108 109 110 201 202 203 204 205 206 207 301 302 303 304 305 306 307 308 309 310 FRI 1021 421 7468 01 421 8202 FRI 1022 421 7515 214 0202 280 0417 509 5453 91 V B 512 5046 15000 512 5046 8000 450 5126 450 5134 450 5135 270 5081 280 5009 01 310 5029 G20 601 0460 211 5479 01 000 P00416 W 000 P00408 W 050 H00400 060 S00400 060 F00400 000 P00312 W 000 T00408 0B FRI 60001 FRI 60002 FRI 60003 FRI 60004 FRI 60005 FRI 60006 FRI 60008 600 6972 0100 600 6972 0120 600 6972 0700 D 2 2 AC BRACKET STICKER C P W PIC STICKER EARTH MARK CONNECTOR LID STICKER FIBER CABLE TX RX INLET PANEL TYPE TERMINAL BINDING POST BLACK SW ROCKER 18 V B C P 15000MA CE UL C P 8000MA CE UL 220 240V AREA MAGNET CONTACT S N10CX AC 110V AREA MAGNET CONTACT 5 10 230V AC 220 240VAREA MAGNET CONTACT S N10CX 120 AC 120V AREA NOISE FILTER 20A CORD CLAMP 21 SUMITUBE F G 20MM PLASTIC TIE BELT 100 MM CONN OPT JOINT AC 110 120VAREA SCR PH W FS 16 SCR PH W FS 8 HEX NUT M4 SPR WSHR M4 FLT WSHR M4 SCR PH W FS M3 X 12 M SCR TH BLK M4 X 8 WIRE HARN AC INLET A WIRE HARN AC INLET B WIRE HARN EARTH AC INLET
33. 175 FRI 2176 FRI 2177 FRI 2178 FRI 2179 FRI 2180 2181 2182 2183 2184 2157 045 SU0424 Z 123 5107 100 5252 100 5360 100 5229 100 5361 100 5362 601 10805 280 5275 SR10 509 5636 601 10806 DESCRIPTION NOTE ROLLER PIN STP RUBBER PIN STOPPER RUBBER SIDE GUARD KEY KNOB INSULATOR SHEET CENTERING SPRING SHAFT CASE F SHAFT CASE R CENTERING HEAD SPRING BRKT HOLDER CLUTCH BAR CLUTCH PIN CLUTCH SHAFT CENTERING BRKT CR SPRING BRKT GUIDE ROLLER CENTER PLATE COLLAR COLLAR 18 COLLAR 14 CENTERING POSITION SIDE PLATE B SIDE PLATE A PLATE BRKT SLIDE PLATE BASE SW DOG SP GUIDE SHAFT RUBBER BEAM RUBBER COMPRESSION SPRING SLIDE PLATE SHIFT SHAFT X 24 SPRING PIN SHAFT PIN G5042 8020 FRI BEARING ROLLER 25 BEARING 17 BEARING 17 RODEND 8 BEARING 12 TIE BELT CORD CLAMP SR10 SW MICRO TYPE SS 5GL2T BRAKE BXH 08 115 www seuservice com ASSY 6SPEED SHIFTER FRI 2150 ITEM NO 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 301 PART NO FAS 000033 000 P00408 W 000 P00510 W 020 000410 0Z 020 0005 10 0Z 020 000525 0Z FAS 200037 000 F00406 028 A00406 P 060 S00400 060 S00500 060 S00600 060 00500 050 U00500 050 H00800 065 501450 7 FRI 60094 www seuservice com DESCRIPTION SCR PH W FS 2 3 X 12 SCR PH W FS M4 X 8 M SCR PH W FS M5 X 10 HEX SKT H CAP SCR BLK OZ M4 X 10 HEX SKT H CAP SCR BLK O
34. 2 123 www seuservice com ASSY CORNER LIGHT R FRI 3150 ITEM NO e 101 102 103 104 105 201 202 203 204 301 302 PART NO FRI 3151 FRI 3152 FRI 3153X FRI 3154 FRI 3155 440 WS0002XEG FRI 3158 FRI 3159 440 CS0180 EG 400 5414 390 6651 601 7467 310 5047 6H0014 601 0460 000 T00408 0B 000 00412 0 000 P00312 W 068 441616 0C FRI 60075X FRI 60078 www seuservice com 2 2 DESCRIPTION NOTE CORNER LIGHT BOX CORNER LIGHT LID LID EDGE PACKING CORNER REFRECTOR LIGHT HOLDER STICKER W POWER OFF ENG LIGHT HOLDER BUSH LIGHT HOLDER SPACER STICKER C KEEP OUT ENG INVERTER FIP24 12N UX EXT ELECTRODE CFX12AYG 36H L LOCK BK VINYL TUBE 6H 0014CM PLASTIC TIE BELT 100 MM M SCR TH BLK M4 X 8 M SCR TH CRM M4 X 12 SCR PH W FS M3 X 12 FLT WSHR CRM 4 4 16 X 1 6 WIRE HARN CORNER R AC WIRE HARN BRAKE LAMP R 124 G1 ASSY REAR ROOF FRI 3200 D 1 2 125 www seuservice com G1 ASSY REAR ROOF 3200 D 2 2 ITEM NO PART NO DESCRIPTION NOTE 1 FRI 3250 ASSY TOP LIGHT 2 FRI 3201 REAR ROOF 3 FRI 3202X FL PLATE 4 FRI 3203 ROOF BRKT REAR 8 440 WS0002XEG STICKER W POWER OFF ENG 9 440 WS0012XEG STICKER W HIGH TEMP ENG 10 FRI 3207 LAMP BLIND LID 13 FRI 3158 LIGHT HOLDER BUSH 14 FRI 3208 PLATE HOLDER 201 000 T00416 0B M SCR TH BLK M4 X 16 202 000 T00630 0B M SCR TH BLK M6 X 30 203 060 F00400 0B FLT WSHR BLK M4 204 050 C00400 3B CAP NUT TYPE3 BLK M4 206 0
35. 4 BOTH SIDE MONITOR GLASS 1 Take out 9 screws and remove Monitor Cover TRUSS SCREW 9 in total chrome P MA X 10 flat washer used MONITOR COVER PHOTO 14 4 a Q Take out 3 screws and remove Monitor Side Cover MONITOR SIDE COVER TRUSS SCREW 3 black M4 X 8 PHOTO 14 4b 55 www seuservice com 0 Take out 2 screws to remove the Side Cover Bracket SIDE COVER BRACKET PHOTO 14 4 c MA X 8 w flat amp spring washers MONITOR BOARD LID 4 Take out 2 screw to remove the Monitor Board Lid 5 Pull out the Monitor Glass PHOTO 14 4d MONITOR GLAS www seuservice com 56 15 REPLACING THE FLUORESCENT LAMP AND LAMPS WARNING CAUTION The Error Lamp is used when the Printer optional is incorporated If the Printer optional is not incorporated disregard the following explanation of replacing the ERROR LAMP Regarding the U S Specifications The parts employed for the U S Specifications machines are procured in the U S A Therefore the parts in the U S Specifications are different from those of described in this section or listed in the PARTS LIST When replacing the Fluorescent Lamp be sure to contact where you purchased the product from When performing work be sure to turn power off Working with power on can cause electric shock and short circuit hazards The Fluorescent Lamp when it gets hot can cause burn Be very careful
36. 4 Remove CRADLE When removing the retaining ring E ring be very careful so as not to bend the rotary shaft Remove stain from the rotary shaft and shaft receiving portions by wiping off with a soft cloth etc 6 After wiping off as per 5 above further apply a dry cloth etc to cause the coin selector to dry completely COIN INSERTION TEST H is the coin rejected when inserted while keeping Once every month when performing the Coin SW Test simultaneously check the following Does the Coin Meter count satisfactorily Does the coin drop into the Cashbox correctly the Reject Button pressed down 45 CRADLE FIG 13b Insert a coin while keeping the Reject Button pressed down and check ifit is rejected COIN METER 7 AC FIG 13 www seuservice com NMOQ L3 vu8 30ISU3A02 LIVES 0841 1 0 9 Ag0 M 4000 IN 53 1 3 2 4000 IN Qv3H Nvd MIY NO dWNS 3 3315 dYNS 2LLSV H NO dvNS D 2 215 14 HINO CBN NOVIS 50 011 HOLIMSOHOIN LV ilV 1d 35 dN 31V 1d 3015 dfi a a a Si D 1 1 SN NO 1441 19 252 SN NO 50 5 184355 31V Id 35 8 101 8001 4 9100010 Do 000 20600 os WIN
37. 408 0B 050 00600 000 P00312 W 600 6972 1600 www seuservice com 2 2 DESCRIPTION NOTE MONITOR FRAME MONITOR HOLD UPPER MONITOR HOLD LOWER SIDE COVER BRKT SIDE BRKT GLASS HOLDER UPPER SIDE GLASS HOLDER LOWER SIDE GLASS MONITOR SIDE COVER MONITOR BD LID BUSH FOR TV COLLAR FOR TV MONITOR MASK RUBBER PACKING NO 96 L 170MM RUBBER PACKING 96 L 580MM MONITOR BD BASE ASSY CLR DSPL 29AUTO MS 2931 S CORD CLAMP SR10 CORD CLAMP 21 SPACER TUBE L 6 EDGING NEW TYPE L 10 EDGING NEW TYPE M SCR FH BLK 10 M SCR PH W FS M4 X 8 M SCR TH BLK M4 X 8 FLG NUT M6 SCR W FS M3 X 12 WIRE HARN EARTH ID5 1600MM 98 17 ASSY STEERING MECHA FRI 2000 D 1 2 Es TORQUE M4 18kgf cm kai M6 57kgf cm MO 1 8kgf cm 99 www seuservice com 17 ASSY STEERING MECHA FRI 2000 ITEM NO 101 102 103 104 105 201 202 203 204 205 206 207 208 301 302 303 FRI 2001 FRI 2003 FRI 2004 FRI 2005 SPG 2108 SPG 2109 100 5351 601 0459 280 5008 280 5275 5 10 601 0460 050 U00800 030 000816 S 060 00800 030 000616 5 060 00600 000 00406 5 060 00400 000 00408 5 FRI 60063 600 6972 0500 600 7204 0500 www seuservice com 2 2 DESCRIPTION NOTE STEERING SHAFT SHAFT BASE F SHAFT BASE R STOPPER BASE STOPPER BOLT STOPPER RUBBER BEARING 25 TIE BELT 150MM CORD CLAMP 15 CORD CLAMP SR10 PLASTIC TIE BELT
38. 6 205 000 P00412 W 206 011 T03510 207 000 T00430 0B 301 FRI 60069 www seuservice com 2 2 DESCRIPTION NOTE ENCLOSURE BAFFLE SPEAKER NET HOLDER COVER EDGE GUARD COVER BRKT SPEAKER BUSH SPKR 4INCH 4 12W25W HARNESS LUG SUMITUBE F F 20MM SUMITUBE F H 20MM M SCR W FS X 30 FLG NUT M4 M SCR TH BLK M4 X 16 SCR FH 5 X 16 M SCR W FS 12 TAP SCR TH 3 5 X 10 M SCR TH BLK M4 X 30 WIRE HARN SEAT SP 132 ASSY EFECT SW 3400 ITEM NO PART NO 1 FRI 3401 2 FRI 3402 3 FRI 3403 4 FRI 3404 5 FRI 3405 101 509 5838 Y 102 509 5653 103 253 5380 04 104 253 5380 02 301 FRI 60074 DESCRIPTION NOTE SW PLATE BUTTON SHEET SC BUTTON SHEET TC BUTTON SHEET ABS BUTTON SHEET IBS SW LWIL 15Y TK1670 PB W L 6V W O LEN PLT 11110 BUTTON COVER 1L BL BUTTON COVER 1L GR WIRE HARN EFFECT SW 133 www seuservice com 37 ASSY MAIN BD DX FRI 4000 D 1 2 89 www seuservice com 134 37 ASSY MAIN BD DX FRI 4000 ITEM NO D 101 103 104 105 106 201 202 203 204 205 206 301 302 303 304 305 306 PART NO FRI 4050 APC 4001 105 5368 APC 4002 400 5397 280 5009 01 838 13760 280 0419 601 0460 270 5052 04 011 F00310 000 P00408 W 000 P00412 W 011 T03512 000 P00406 W 011 P00325 FRI 60017 FRI 60018 FRI 60019 FRI 60020 FRI 60021 FRI 60022 D 2 2 DESCRIPTION NOTE ASSY SHIELD CA
39. 68 302 600 6972 0600 D 2 2 DESCRIPTION NOTE SOUND UNIT SEAT BACK COVER UPPER SEAT LOWER SEAT SEAT BASE SEAT FRAME SEAT SLANT TRAY FRONT TRAY COVER REAR TRAY COVER CABLE BEAR BRKT SPEAKER SUPPORT ARM REAR COVER GULL PLATE PROTECT RUBBER RUBBER PLATE SPEAKER NET L SPEAKER NET R SHOULDER PAD PLATE S RAIL LOWER HEAD CUSION SEAT RAIL SEAT RAIL R SCRIVET 8 1K31 CABLE BEAR L 009 CORD CLAMP 21 CORD CLAMP SR10 HEX BLT W S M8 X 16 HEX BLT W S M8 X 50 HEX NUT M8 SPR WSHR M8 FLT WSHR 8 5 22 X 1 6 M SCR TH BLK M4 X 8 M SCR PH W FS M4 X 10 M SCR TH BLK M5 X 16 M SCR TH BLK M6 X 16 FLT WSHR M8 M SCR PH W S X 8 FLT WSHR M4 WIRE HARN EXT SEAT SP C WIRE HARN EARTH ID5 0600MM 129 www seuservice com SOUND UNIT FRI 3350 ITEM NO PART NO DESCRIPTION NOTE 1 FRI 3360 ASSY SPEAKER 2 FRI 3351 MOUNT ARM 101 280 5275 5 10 CORD CLAMP SR10 201 030 000816 S HEX BLT W S M8 X 16 202 060 00800 FLT WSHR M8 www seuservice com 130 35 ASSY SPEAKER FRI 3360 D 1 2 SEE A Where aA is removed 131 Wwww seuservice com 35 ASSY SPEAKER FRI 3360 ITEM NO PART NO 1 FRI 3361 2 FRI 3362 3 FRI 3363 4 FRI 3364 5 FRI 3365 6 FRI 3366X 7 FRI 3367 8 FRI 3368 101 130 5210 102 280 0419 103 310 5029 F20 104 310 5029 H20 201 000 P00430 W 202 050 F00400 203 000 T00416 0B 204 000 F0051
40. 68 652016 0B FLT WSHR BLK 6 5 20 X 1 6 208 000 T00408 0B M SCR TH BLK M4 X 8 209 068 441616 0B FLT WSHR BLK 4 4 16 X 1 6 210 000 T00420 0B M SCR TH BLK M4 X 20 www seuservice com 126 32 ASSY TOP LIGHT FRI 3250 ITEM NO 2 3 101 201 FRI 3251 253 5457 421 7501 17 390 6603 20EX 050 F00400 FRI 60081X DESCRIPTION NOTE TOP FL BOX FL HOLDER STICKER FL 20W ASSY FL20W EX W CONN HIGH T CE FLG NUT M4 WIRE HARN BILLBOARD FL 127 www seuservice com 33 ASSY SEAT FRI 3300 D 1 2 I A A SS N 8 Bolt for fastening plastic 82kgf cm Others 195kgfecm MA Sonic Lock Portion 9kgfecm NOTE SCREW FASTENING TORQUE TO BE www seuservice com 128 33 ASSY SEAT FRI 3300 ITEM NO PART NO 1 FRI 3350 2 FRI 3301 3 FRI 3302 4 FRI 3303 5 FRI 3304 6 FRI 3305 7 FRI 3306 8 FRI 3307 9 FRI 3308 10 FRI 3309 11 FRI 3310 12 FRI 3312 13 FRI 3313 14 SRT 2408 15 SPG 2411 16 STC 1608 17 STC 1609 18 SRT 2409 19 117 5414 20 FRI 3314 101 601 9059 91 102 601 9060 91 103 280 5297 104 601 6981 009 105 280 5009 01 106 280 5275 5 10 201 030 000816 S 202 030 000850 S 203 050 H00800 204 060 S00800 205 068 852216 206 000 T00408 0B 207 000 P00410 W 208 000 00516 0 209 000 00616 0 210 060 00800 21 000 00408 5 212 060 F00400 301 FRI 600
41. 9 01 280 5185 6 280 5292 601 6231 D010 601 6231 D045 000 F00410 0B 000 P00408 W 000 T00408 0B 000 P00412 W 050 F00400 050 F00600 068 441616 000 P00312 W 600 6972 1600 www seuservice com 2 2 DESCRIPTION NOTE MONITOR FRAME MONITOR HOLD UPPER MONITOR HOLD LOWER SIDE COVER BRKT SIDE BRKT GLASS HOLDER UPPER SIDE GLASS HOLDER LOWER SIDE GLASS MONITOR SIDE COVER MONITOR BD LID WIRE BRKT BUSH FOR TV COLLAR FOR TV MONITOR MASK RUBBER PACKING NO 96 L 170MM RUBBER PACKING NO 96 L 580MM MONITOR BD BASE ASSY CLR DSPL 29AUTO MS 2931 S CORD CLAMP SR10 CORD CLAMP 21 SPACER TUBE L 6 CORD CLAMP 18 PUSH TYPE EDGING NEW TYPE L 10 EDGING NEW TYPE M SCR FH BLK 10 M SCR PH W FS M4 X 8 M SCR TH BLK 8 SCR PH W FS M4 X 12 FLG NUT M4 FLG NUT M6 FLT WSHR 4 4 16 1 6 SCR PH W FS M3 X 12 WIRE HARN EARTH ID5 1600MM 96 ASSY MONITOR RIGHT APC 1200 D 1 2 Details of PART A 97 www seuservice com ASSY MONITOR RIGHT APC 1200 ITEM NO 1 ON Q Q D 101 102 103 104 105 106 201 202 203 204 205 301 PART NO APC 1151 APC 1152X APC 1153X APC 1154X APC 1155X APC 1156X APC 1157X APC 1054 APC 1159X APC 1058X 280 5112 280 5113 APC 1083 601 10562 0170 601 10562 0580 APC 1086 200 5710 280 5275 SR10 280 5009 01 280 5185 6 601 6231 D010 601 6231 D045 000 F00410 0B 000 P00408 W 000 T00
42. AKE Before starting to work ensure that the Power SW is OFF Failure to observe this can cause electric shock or short circuit WARNING Use care so as not to damage wirings Damaged wiring can cause electric shock or short circuit Do not touch undesignated places Touching places not designated can cause electric shock or short circuit This work should be performed by the Location s Maintenance Man or Serviceman Performing work by non technical personnel can cause electric shock hazard When performing work such as parts replacement other than those specified in this manual be sure to contact where you purchased the product from Confirm the work procedures and obtain precautions from where you purchased the product from prior to performing work Inappropriate parts replacement and or installation with erroneous adjustment can cause an overload or the parts to come into contact resulting in an electric shock a short circuit and a fire If Accel and Brake operation is not satisfactory adjustment of Volume installation position or Volume replacement is needed Also be sure to apply greasing to the gear mesh portion once every 3 months 11 1 ADJUSTING AND REPLACING THE The appropriate value for both ACCEL Volume and Brake Volume is under 30H when released and over COH when stepped on Check Volume values in the TEST mode Since work is performed inside the energized cabinet be very careful so as not to tou
43. AR 15 SUMITUBE F F 15MM HARNESS LUG CORD CLAMP SR10 SET SCR HEX SKT CUP P M3 X 4 M SCR PH W FS M3 X 8 M SCR TH BLK M4 X 6 M SCR PH W FS M4 X 8 M SCR W FS M4 X 10 M SCR PH W FS M4 X 16 M SCR TH CRM M6 X 8 WIRE HARN CLUTCH 110 ASSY REAR SUB CABI FRI 3001 D 1 2 FOR EARTH 5 S 80066 111 www seuservice com ASSY REAR SUB CABI FRI 3001 ITEM NO 101 102 103 201 202 203 204 206 207 209 210 211 212 301 303 304 305 306 307 PART NO FRI 3002 FRI 3003 FRI 3004 FRI 1009 FRI 3010 FRI 3013 FRI 3022 FRI 3024 FRI 3025 FRI 3026 FRI 3027 FRI 3033 FRI 3011 FRI 3012 FRI 3102 117 5233 ARC 1006 601 5699X 253 5457 421 7501 09 440 WS0002XEG 440 WS0012XEG 601 9377 390 6603 30EX 280 5009 01 030 000630 SB 000 P00416 W 030 000630 S 060 00600 079 000008 000 00416 0 000 P00430 W 050 H01600 000 P00408 S 060 F00400 FRI 6003 FRI 60072X FRI 60079X FRI 60080 600 6972 0600 600 6972 1000 www seuservice com 2 2 DESCRIPTION NOTE REAR CABINET CORNER BRKT L CORNER BRKT R CASTER SPACER PLATE FR CONN PNL FOOT PLATE MATA SASH A SASH B SASH C SASH D SP PNL BRKT HOLDER Z UPPER HOLDER Z LOWER REFRECTOR PLATE LEG BRACKET BLACK LEG BRACKET LEG ADJUSTER BOLT M16 X 75 FL HOLDER STICKER FL30W STICKER W POWER OFF ENG STICKER W HIGH TEMP ENG CASTER FAI 75 ASSY FL30W EX W
44. AUTIONS BE HEEDED WHEN MOVING THE MACHINE 27 29 HANDLE MECHA ses 30 9 1 ADJUSTING OR REPLACING THE V R sisi 30 33 9 2 GREASING iine nti e p ER Seer EE coru ceri ue Runs 33 9 3 REPLACING PADDLE WING SHIFT SWITCH 34 35 6 SPEED e 36 10 1 REMOVING THE SHIFT arcos 36 37 10 2 REPLACING THE SWITCH 38 ACCELERATOR amp 39 11 1 ADJUSTING AND REPLACING THE V R eee 39 40 11 2 EE 40 CLUTCH PEDAL nee 41 12 1 REMOVING THE CLUTCH PEDAL eene nennen 41 42 12 2 VOLUME ADJUSTMENT REPLACEMENT eee 43 12 3 Sa hani ue bd v e MARA HAE aia 44 COIN SELECTOR inedite cna a inei eite D sii 45 48 MONITOR u aaa 49 14 1 CAUTIONS AND WARNINGS CONCERNING THE SAFETY FOR HANDLING THE MONITORS rte 49 51 14 2 CAUTIONS TO BE HEEDED WHEN CLEANING THE CRT SURFACES 51 14 3 9 52 53 14 4 CLEANING THE MONITOR GLASS 1z eene 54 56 REPLACING THE FLOU
45. BE F D 20 MM PLASTIC TIE BELT 100 MM EARTH TERMINAL PLATE 6P L FILTER D 84 5 ASSY FRONT SUB CABI FRI 1001 ITEM NO 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 301 302 303 304 305 306 307 308 309 310 311 312 313 314 PART NO 000 P00416 W 000 T00420 0B 000 T00430 0B 011 F00310 011 T00312 011 T03512 030 000630 SB 030 000830 SB 050 H01600 060 F00600 0B 060 F00800 0B 068 441616 0B 011 F03516 FAS 110010 000 P00408 S 050 H00400 060 S00400 060 F00400 600 6455 02 600 7134 600 6275 0150 600 6972 0150 600 6972 0400 600 6972 1200 FRI 6001 FRI 6002 FRI 6004 600 7195 3000 APC 60091 APC 60092 APC 60093 600 7141 100 FRI 60092 D 3 3 DESCRIPTION NOTE M SCR PH W FS M4 X 16 M SCR TH BLK M4 X 20 SCR TH BLK 30 TAP SCR FH 3 X 10 TAP SCR TH 3 X 12 TAP SCR TH 3 5 X 12 HEX BLT BLK W S M6 X 30 HEX BLT W S BLK X 30 HEX NUT M16 FLT WSHR BLK M6 FLT WSHR BLK M8 FLT WSHR BLK 4 4 16 X 1 6 TAP SCR FH 3 5 X 16 TAP SCR FH 1 BLK 3 X 10 M SCR PH W S X 8 HEX NUT M4 SPR WSHR M4 FLT WSHR M4 WIRE HARN C C DOOR SINGLE OTHERS WIRE HARN COIN CHUTE 2 USA ASSY FIBER CABLE 5 0150CM WIRE HARN EARTH ID5 0150 WIRE HARN EARTH 05 0400MM WIRE HARN EARTH 05 1200MM ASSY WIRE FRONT CABI AC ASSY WIRE FRONT CABI DC ASSY WIRE EARTH ASSY PRINTER CABLE 3000 MM WIRE HARN RGB L WIRE HARN RGB C WIRE HARN RGB R CABLE JVS TYPE A B
46. BILLBOARD FRI 1018 B STICKER MONITOR COVER FRI 3016 BACK PLATE BASE FRI 3056 CORNER COVER 422 0766 01 PLAY INSTR SH FRI LEVEL ENG 422 0765 01 PLAY INSTR SH FRI COURSE ENG 422 0767 01 PLAY INSTR SH FRI ASSIST ENG 421 7308 DENOMI SH FRI 1017 B DESIGN PLATE CONT PANEL FRI 3019 SHIFT GATE 421 10092 01 STICKER DENOMI FRI ENG FRI 2002 STEERING EMBLEM FRI FRL3401 B STICKER SW PLATE FRI 1018 C DESIGN PLATE SHIFT PATTE 73 www seuservice com 20 PARTS LIST 1 TOP ASSY FRI DX D 1 3 SECTION www seuservice com 74 1 TOP ASSY FRI DX ITEM NO Dont EUA 201 202 203 204 205 206 207 208 209 210 211 212 401 402 403 404 406 408 409 410 411 413 414 PART NO FRI 1000 FRI 3000 APC 0001 FRI 0001 FRI 0002 FRI 0003 FRI 0004 FRI 0005 FRI 0006 421 7020 421 8479 01 440 W S0002XEG 440 DS0013XEG 440 WS0170 JP 440 CS0181 EG SGM 4048 FRI 0007 440 CS0179 EG SGM 4507 440 CS0175 EG 421 10097 030 000830 SB 068 852216 0B 030 000820 SB FAS 300005 000 T00630 0B 000 T00412 0B 000 P00408 S 060 F00400 068 652016 0B 000 T00416 0C 050 000800 008 B00830 0B 220 5576 SGM 4111 280 5009 01 540 0009 01 600 6729 600 6695 600 6618 220 5484 220 5373 514 5086 6300 509 5636 509 5387 420 6507 01 420 6508 01 D 2 3 DESCRIP
47. CLUTCH PEDAL Before starting to work ensure that the Power SW is OFF Failure to observe this can cause electric shock or short circuit WARNING Use care so as not to damage wirings Damaged wiring can cause electric shock or short circuit Do not touch undesignated places Touching places not designated can cause electric shock or short circuit This work should be performed by the Location s Maintenance Man or Serviceman Performing work by non technical personnel can cause electric shock hazard When performing work such as parts replacement other than those specified in this manual be sure to contact where you purchased the product from Confirm the work procedures and obtain precautions from where you purchased the product from prior to performing work Inappropriate parts replacement and or installation with erroneous adjustment can cause an overload or the parts to come into contact resulting in an electric shock a short circuit and a fire If the Clutch Pedal s operation is not satisfactory the installation position adjustments or V R replacement is needed Also be sure to apply greasing to the V R Gear mesh portion and the 2 Springs once every 3 months 12 1 REMOVING THE CRUTCH PEDAL 1 Turn off power 2 Take out 4 Hexagon Bolts At this time support the Clutch Pedal as taking out the bolts can cause the Clutch Pedal to fall PHOTO 12 1a HEXAGON BOLT 4 M8 X 30 w spring washer
48. ER 220V AC 220V AREA STICKER 240V AC 240V AREA STICKER 120V AC 120V AREA DENOMI SH 1GAME STICKER FCC STICKER SEGA USA 5 76 2 ASSY FRONT CABINET FRI 1000 D 1 3 DOOD SECTION A A NOTE M8 BOLT FASTENING TORQUE BE 178kgfecm a _ 1 FA 69 tp 2741 Al Ee 8 25 D AN _ AEE il L 5 2 48 67 1 7 VA huy AVE Oe 77 Wwww seuservice com 2 ASSY FRONT CABINET FRI 1000 D 2 3 ITEM NO PART NO 1 SPG 2001 2 FRI 1001 3 APC 1100 4 APC 1150 5 1200 6 FRI 2000 7 FRI 2050 8 FRI 2100 9 FRI 2200 10 FRI 2400 13 FRI 4000 14 FRI 4100 15 FRI 4200 16 FRI 4300 17 FRI 4400 18 FRI 2002 19 APC 1153X 20 APC 1053X 21 APC 1054 22 APC 1055 23 APC 1056 24 APC 1057 25 APC 1058X 26 FRI 1015 27 FRI 1016 28 FRI 1017 29 FRI 1018 30 FRI 1019 31 601 10562 0170 32 601 10562 0580 33 FRI 1054X 34 FRI 1051 35 FRI 1052 36 FRI 1053 37 FRI 2055 38 FRI 2504 41 280 5112 42 280 5113 43 253 5366 44 SPG 2039 45 APC 1077 46 APC 1083 47 APC 1014 48 APC 1015 49 APC 1016 50 APC 1017 51 SRT 3206 52 FRI 2006 53 FRI 2007 55 440 CS0140 JP 56 421 10092 01 97 422 0765 01 58 422 0766 01 59 422 0767 01 www seuservice com DESCRIPTION NOTE STEERING WHEEL ASSY FRONT SUB CABI ASSY MONITOR CENTER ASSY MONITOR LEFT ASSY MONITOR RIGHT A
49. N To avoid injury and trouble be sure to constantly give careful attention to the behavior and manner of the visitors and players To avoid injury and accidents those who fall under the following categories are not allowed to play the game Those who need assistance such as the use of an apparatus when walking Those who have high blood pressure or a heart problem Those who have experienced muscle convulsion or loss of consciousness when playing video game etc Those who have a trouble in the neck and or spinal cord Intoxicated persons Pregnant women or those who are in the likelihood of pregnancy Persons susceptible to motion sickness Persons whose act runs counter to the product s warning displays To avoid injury resulting from falling down and electric shock due to spilled drinks instruct the player not to place heavy items or drinks on the product To avoid electric shock and short circuit do not allow customers to put hands and fingers or extraneous matter in the openings of the product or small openings in or around the doors To avoid falling down and injury resulting from falling down immediately stop the customer s leaning against or climbing on the product etc To avoid electric shock and short circuit do not allow the customers to unplug the power plug without a justifiable reason To avoid a fire due to a cigarette stub caution the customers so as not to put dust on the Seat rear Caution the customer
50. O 9 TRUSS SCREW 4 MAX 16 www seuservice com 30 0 Perform the adjustment while another person is securing the Steering Wheel in the centering position 4 The V R is on the VR BASE a white plastic made part Loosen the 2 screws which secure the VR BASE and adjust the angle and appropriateness of gear mesh by moving the VR BASE G Adjust to an appropriate mesh by securing the Steering Wheel in the direction allowing the car to advance straight forward and ensuring the D CUT FACE of the Volume shaft is oriented as shown 6 Tighten the 2 screws to secure the VR BASE VR BASE SCREW 2 X 12 w flat amp spring washers D CUT FACE FIG 9 7 Turn on power Set the Center Value of the Volume in the TEST mode 9 In TEST mode check to see if the Volume Value varies smoothly in accordance with steering wheel operation 31 www seuservice com REPLACING THE VOLUME SCREW 2 X 12 w flat amp spring washers Disconnect the connector from the Volume Take out 2 screws to remove the Volume together with VR BASE from the HANDLE MECHA PHOTO 9 1 b 0 Take out 2 screws from the VR BASE reverse side to remove the Volume together with VR Bracket from the VR BASE 4 Remove the Volume from VR Bracket and replace TRUSS SCREW 2 12 PHOTO 9 www seuservice com 32 5 After replacing
51. Printer Q Unlock with the Master Key and remove the Printer Door 0 Draw ASSY Printer toward you FIG 7 2 b lt 77 21 www seuservice com 4 Pull up the Head Up Lever 5 Take out the roll shaft from the Printer 6 Pass the shaft through the core of the new Roll Paper 7 Install the roll shaft in which the paper is inserted into the unit Make sure to put the Roll Paper on to the correct position Roll shaft New Roll Paper PD d 5 Head Up Lever FIG 7 2 Insert the paper tip in to the roll paper insertion slot Feed the Roll Paper tip through the exit slot straight by hand At this time if the Paper tip comes out in excess of the exit slot Printer performs automatic feeding and cuts the Paper after feeding about one page long 9 Push down the Head Up Lever FIG 7 24 The feeding point of the Roll Paper tip Push down the Head Up Lever FIG 7 26 www seuservice com 22 Select and execute the INIT in the PRINTER TEST The PRINTER INIT message flashes next to MESSAGE on the monitor and then goes off The Printer s initialization is finished D Select and execute the POSITION SET NOW PRINTING message is displayed next to the MESSAGE on the monitor and then goes off The Printer starts automatic feeding of the paper AUTO LOADING and then cuts the paper automatically If the Paper tip position is appropriate the automatic feeding s movement
52. REA Used for installation see of Section 6 TAMPERPROOF WRENCH M8 540 0009 01 1 TOOL CORD CLAMP 280 5009 01 1 Used for securing the power cord see 4 of Section 6 7 www seuservice com VOL CONT B 5K OHM 220 5484 1 220 5373 Spare see Section 9 11 12 FUSE 6 3A 250W 514 5086 6300 1 Spare see Section 17 5 TAMPERPROOFTSCREW 008 B00830 0B 2 Used for installing BILLBOARD see 2 of Section www seuservice com SW MICRO TYPE SW MICRO TYPE 509 5387 2 509 5636 2 Spare see Section 9 Spare see Section 10 CARTON BOX 601 10577 1 Used for transporting the Game Board Refer to Next Page HOW TO USE THE CARTON BOX When requesting for the replacement repair of this product s Game Board NAOMI BOARD follow the instructions below Transporting the Game Board in an undesignated status is unacceptable An erroneous handling can cause parts damage Put the Game Board in the Carton Box together with the Shield Case Do not unnecessarily disassemble nor remove parts By paying careful attention to the direction shown by the following Figure put the Shield Case in the Carton Box IMPORTANT FILTER BD side Ensure that the direction in which the Shield Case is packed is correct Remove the Brackets the shape differs depending on the specific type of machine Enfold the Shield Case with the packing material shown and put it i
53. RESCENT LAMP 57 65 PERIODIC INSPECTION onte nette EE HEP ODE sit tete 66 67 TROUBLESHOOTING erii 68 70 GAME BOARD reiten ara tober GRO POT ram 71 15 TAKING OUT THE BOARD rrt rtt tnnt 71 72 18 2 COMPOSITION OF GAME 72 DESIGN RELATED PARTS sucessores sen pect neta reo Ter En oid e bo E o e TES 73 PARTS LIS To essas 74 143 WIRE COLOR CODE TABE 3 tart 144 WIRING DIAGRAM sits seissanta an edia 145 149 SPECIFICATIONS Installation Space 1 310 mm X 2 830 mm D 51 6 in X 111 4 in Height 2 660 mm 104 7 in Weight 370 kg 815 7 16 Power maximum current 600 W 6 7 A AC 110V 50 Hz AREA 600 W 6 7 A AC 110V 60 Hz AREA 580 W 6 0 A AC 120V 60 Hz AREA 590 W 3 5 A AC 220V 50 Hz AREA 580 W 3 4 A AC 220V 60 Hz AREA 600 W 3 4 A AC 230V 50 Hz AREA 580 W 3 2 A AC 230V 60 Hz AREA 600 W 3 2 A AC 240V 50 Hz AREA 590 W 3 2 A AC 240V 60 Hz AREA For TAIWAN Power current 600 W 6 7 A MAX 340 W 4 0 A MIN MONITOR 50 TYPE COLOR MONITOR INTRODUCTION OF THE OWNERS MANUAL This Owner s Manual is intended to provide detailed descriptions together with all the necessary information covering the general operation of
54. S M4 X 8 S TITE SCR PH W F M3 X 8 M SCR PH W FS M3 X 20 M SCR PH W FS M4 X 12 WIRE HARN FAN MOTOR MASTER WIRE HARN FAN MOTOR SLAVE 137 www seuservice com ASSY PWR SPLY FRI 4100 D 1 2 2 0 20 3 X38 DEA PRIMARY 25 Note 1 450 5163 103 should be set to 3 sec 2 Make sure that there is no wiring etc in the slash mark portions ASSY PWR SPLY FRI 4100 D 2 2 ITEM NO D 101 102 103 104 105 106 107 108 110 111 201 202 203 204 205 207 208 301 302 303 304 305 306 307 308 310 PART NO FRI 4101 FRI 4102 839 0976 421 7468 01 560 5430 H 560 5431 H 117 5225 450 5163 214 0191 601 7783 450 5126 280 5169 280 0419 280 5275 5 10 512 5046 15000 000 P00512 W 011 T03512 000 P00412 W 000 P00320 W 000 P00416 W 000 P00416 S 000 P00325 W FRI 60009 FRI 60010 FRI 60011 FRI 60012 FRI 60013 FRI 60014 FRI 60015 FRI 60016 FRI 60007 DESCRIPTION NOTE WOODEN PWR SPLY BASE PWR SPLY BRKT CONN BD STICKER C P W PIC XFMR 100 120V 100V 15A WB 110 120V AREA XFMR 220 240V 100V 15A WB 220 240V AREA TERMINAL 3P 20A TIMER RELAY GT5P N30SA100 RELAY SOCKET FIXED SPRING MAGNET CONTACT S NIOCX CORD CLAMP TL 20S HARNESS LUG CORD CLAMP SR10 15000MA CE UL M SCR PH W FS M5 X 12 TAP SCR TH 3 5 X 12 M SCR PH W FS M4 X 12 M SCR PH W FS M3 X 20 M SCR PH W FS M4 X 16 M SCR PH W S M4 X 16 M SCR PH W FS M3 X 25 WIRE HARN
55. SE FRI WOODEN MAIN BASE SHIELD CASE BRKT SW REGU BRKT SW REGU FOR JVS CORD CLAMP 21 DC SEQUENCE BD HARNESS LUG PLASTIC TIE BELT 100 MM L FILTER D TAP SCR FH 3 X 10 M SCR PH W FS M4 X 8 M SCR PH W FS 12 TAP SCR TH 3 5 X 12 SCR W FS 6 TAP SCR PH 3 X 25 WIRE HARN MAIN BD AC IN WIRE HARN MAIN BD DC OUT WIRE HARN MAIN BD DC A WIRE HARN MAIN BD WIRE HARN MAIN BD DC C WIRE HARN MAIN BD DC D 135 www seuservice com ASSY SHIELD CASE FRI FRI 4050 www seuservice com 136 D 1 2 00000000000000 00000000000000 5 99899998 ASSY SHIELD CASE FRI FRI 4050 ITEM NO t O D p R D 101 102 103 201 202 203 204 301 302 PART NO 105 5366 105 5367 839 1109 02 839 1110 02 833 13841 421 9174 01 421 10023 AAA 421 10023 BAM 441 313841 601 10577 105 5390 421 9757 L 421 9757 C 421 9757 R 260 0064 280 5275 SR10 601 0460 000 P00408 W 010 P00308 F 000 P00320 W 000 P00412 W APC 60045 APC 60046 D22 DESCRIPTION NOTE SHIELD CASE NAOMI MULTI SHIELD CASE LID NAOMI MULTI FLT BD NAOMI MULTI MASTER FRI FLT BD NAOMI MULTI SLAVE FRI GAME BD FRI DX STICKER CAUTION ANTISTATIC STICKER BD SERIAL NUMBER AAA STICKER BD SERIAL NUMBER BAM STICKER 833 13841 CARTON BOX NAOMI MULTI FIXING BRACKET STICKER L STICKER C STICKER R FAN MOTOR DC12V CORD CLAMP SR10 PLASTIC TIE BELT 100 MM M SCR PH W F
56. SSY STEERING MECHA ASSY PADDLE SHIFT STEERING MOTOR UNIT PEDAL UNIT CLUTCH UNIT ASSY MAIN BD DX ASSY PWR SPLY DX ASSY I O BASE DX ASSY AUDIO BASE ASSY SERVO DRV BASE STEERING EMBLEM FRI MONITOR HOLD LOWER GLASS HOLDER REAR GLASS GLASS HOLDER UPPER CENTER GLASS HOLDER LOWER CENTER GLASS SUSH MONITOR BD LID CONT PNL BRKT UPPER CONT PNL UPPER CONT PNL LOWER MONITOR COVER L MONITOR COVER R RUBBER PACKING NO 96 L 170MM RUBBER PACKING 96 L 580MM CUSHION SPONGE 550 ROOF BRKT FRONT BOSS PLATE SIDE BOSS PLATE CENTER BOSS COVER PRINTER BLIND LID BUSH FOR TV COLLAR FOR TV CASH BOX SPACER RING AIR VENT PLATE MONITOR MASK COVER BRKT A COVER BRKT B COVER BRKT C COVER BRKT D KEY 5X5X17 KEY 6 X 6 16 KEY 5X5 X10 STICKER C GEAR STISKER DENOMI FRI ENG PLAY INSTR SH FRI COURSE ENG PLAY INSTR SH FRI LEVEL ENG PLAY INSTR SH FRI ASSIST ENG 78 2 ASSY FRONT CABINET FRI 1000 ITEM NO 62 63 64 101 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 225 226 227 230 301 PART NO FRI 1055 FRI 1056 FRI 1057 111 1131 000 T00408 0B 000 P00416 W 000 T00410 0B 000 T00410 0C 000 T00416 0B 008 B00830 0B 020 000820 0Z 030 000630 SB 030 000820 SB 030 000830 SB 030 000850 SB 032 000425 050 F00600 060 F00800 0B 060 S00800 0B 068 441616 068 441616 0B 068 441616 0C 068 652016 0B 068 852216 0B 000 T
57. STR 1070 102 FLOW ITEM NO PART NO DESCRIPTIONNOTE 1 105 5340 01 FAN BRKT LONG 101 260 0011 02 AXIAL FLOW 100 50 60HZ 102 601 8543 FAN GUARD 201 000 P00312 W M SCR PH W FS M3 X 12 11 ASSY WIRE FRONT CABI AC FRI 6001 ASSY WIRE FRONT CABI AC is comprised of the following wire harnesses An ASSY DRG is unavailable ITEM NO PART NO DESCRIPTION NOTE 101 601 0460 PLASTIC TIE BELT 100 MM 301 60045 WIRE HARN EXT AC MONITOR 302 FRI 60046 WIRE HARN EXT AC REAR 303 FRI 60047 WIRE HARN EXT AC FRONT 304 FRI 60061 WIRE HARN EXT SERVO PWR 12 ASSY WIRE FRONT CABI DC FRI 6002 ASSY WIRE FRONT CABI DC is comprised of the following wire harnesses An ASSY DRG is unavailable ITEM NO PART NO DESCRIPTION NOTE 101 601 0460 PLASTIC TIE BELT 100 MM 301 FRI 60048 WIRE HARN EXT DC 302 FRI 60049 WIRE HARN EXT SOUND 303 FRI 60050 WIRE HARN EXT COIN 304 FRI 60051 WIRE HARN EXT ANALOG 305 FRI 60052 WIRE HARN EXT SHIFT LOCK A 306 FRI 60053 WIRE HARN EXT BRAKE LAMP A 307 FRI 60054 WIRE HARN EXT REAR CTRL 308 FRI 60055 WIRE HARN EXT BASS SP 309 FRI 60056 WIRE HARN EXT SEAT SP A 311 FRI 60058 WIRE HARN EXT DRV CTRL TX 312 FRI 60059 WIRE HARN EXT DRV CTRL RX 313 FRI 60060 WIRE HARN EXT SERVO ENC 314 FRI 60062X WIRE HARN EXT PADDLE 13 ASSY WIRE EARTH FRI 6004 ASSY WIRE EARTH is comprised of the following wire harnesses An ASSY DRG is unavailable ITEM NO PART NO DESCRIPTION NOTE 101 601 0460
58. TEM NO 4A UC P2 101 201 202 203 204 205 PART NO FRI 2301 FRI 2302 FRI 2303 FRI 2305 FRI 2306 601 10662 030 000825 SB 060 F00800 0B 060 S00600 050 U00600 068 652016 www seuservice com 03 208 205 1 ue SCREW FASTENING TORQUE TO BE M6 57kgf cm 8 178kgf cm DESCRIPTION NOTE ABSORBER BRKT ABSORBER SUB BRKT PLUNGER COMP SPRING FRI STOPPER SHAFT SHOCK ABSORBER W O CAP HEX BLT W S BLK M8 X 25 FLT WSHR BLK M8 SPR WSHR M6 U NUT M6 FLT WSHR 6 5 20 X 1 6 108 03 CLUTCH UNIT FRI 2400 D 1 2 109 www seuservice com 03 CLUTCH UNIT FRI 2400 ITEM NO PART NO 1 FRI 2401 2 FRI 2402 3 FRI 2403 4 FRI 2404 5 FRI 2405 6 FRI 2406 7 FRI 2407 8 FRI 2408 9 FRI 2409 10 FRI 2410 11 FRI 2411 12 FRI 2412 13 FRI 2413 14 FRI 2414 15 FRI 2415 16 FRI 2416 17 FRI 2417 101 100 5359 102 220 5484 220 5373 103 601 7944 104 310 5029 15 105 280 0419 106 280 5275 5 10 201 028 A00304 P 202 000 P00308 W 203 000 T00406 0B 204 000 P00408 W 205 000 P00410 W 206 000 P00416 W 207 FAS 000062 301 FRI 60093 www seuservice com D 2 2 DESCRIPTION NOTE BOTTOM COVER CLUTCH SPRING A CLUTCH GEAR CLUTCH BASE SPRING STOPPER CLUTCH PEDAL CLUTCH SPRING B STOPPER BASE BEARING PLATE VR BRKT SPRING HOLD CLUTCH RUBBER B CLUTCH RUBBER A CLUTCH COLLAR INSULATOR NON SLIP SHEET STOPPER COLLAR BEARING 16 VOL CONT B 5K OHM VOL CONT B 5K OHM GE
59. TION NOTE ASSY FRONT CABINET ASSY REAR CABINET JOINT PIPE ROOF NUT PLATE F ROOF NUT PLATE R CENTER ROOF JOINT PLATE CENTER JOINT BRKT L JOINT BRKT R STICKER CAUTION FORK STICKER INSTR SUNLIGHT ENG STICKER W POWER OFF ENG STICKER D MONITOR ENG STICKER W FALL DOWN STICKER C DOOR HINGE ENG POLY COVER 1250 X 1800 X 2100 SHIPPING BRKT REAR STICKER C DO NOT GET ON ENG POLY COVER 1700 X 1700 X 1950 STICKER C CEPILEPSY ENG STICKER FORK POSITION FRI DX HEX BLT W S BLK M8 X 30 FLT WSHR BLK 8 5 22 X 1 6 HEX BLT W S BLK M8 X 20 HEX BLT CRM W FS X 30 M SCR TH BLK M6 X 30 SCR TH BLK 12 M SCR PH W S M4 X 8 FLT WSHR M4 FLT WSHR BLK 6 5 20 X 1 6 M SCR TH CRM M4 X 16 HEX NUT M8 TMP PRF SCR BH BLK M8 X 30 KEY MASTER FOR 220 5575 KEY BAG SGB 1035X CORD CLAMP 21 WRENCH FOR TAMP SCR M8 AC CABLE CONNECT TYPE 15A AC 110V AREA AC CABLE CONNECT TYPE USA 15A AC 120V AREA AC CABLE CONNECT TYPE FOR EXP AC 220 240V AREA VOL CONT B 5K OHM VOL CONT B 5K OHM FUSE S B 6300MA 250V HBC CE SW MICRO TYPE SS 5GL2T SW MICRO TYPE OWNERS MNL FRI DX ENG SERVICE MANUAL FRI DX ENG 75 www seuservice com 1 TOP ASSY FRI DX ITEM NO PART NO 105 5356 421 8740 280 6609 421 6690 06 421 6690 03 421 6690 05 421 6690 01 421 7308 421 6119 91 421 6120 91 www seuservice com D273 DESCRIPTION NOTE SHIPPING BRKT CAUTION INSTR COP U R REPEAT TIE RF140 STICKER 110V AC 110V AREA STICK
60. USA and 220 7240 and therefore this procedure is not necessary FIG 6 4 b Earth Wire Connection 0 Firmly insert the power plug into the socket outlet Insert the opposite side of Power Cord plug to the AC Unit s connector INLET 4 Perform wiring for the Power Cord and Earth Wire Install protective covering for the Power Cord and Earth Wire FIG 6 4 Connecting Power Cord and Earth Wire In case the Power Plug is apt to come out of place secure the Power Cord to the periphery of the AC Unit with the Cord Clamp an accessory HOW TO USE THE CORD CLAMP 17 www seuservice com 15 TURNING POWER Turn the Main SW of AC Unit ON to turn power on When the power is turned on the fluorescent lamps of the left amp right of Seat in the Rear cabinet the back and the inside the Billboard light up The screen displays the starting of Naomi System and then proceeds to ADVERTISE mode During this time the machine automatically performs Power On check Do not touch the machine until Power On check is finished and ADVERTISE mode is displayed on the screen In the Power On check the steering wheel turns left and right then returns to the centering position and stops In this check the values of V R inside the control panel are corrected Until the check is finished the steering wheel stops automatically do not touch the steering wheel or play the game If you d
61. XFMR IN WIRE HARN XFMR OUT WIRE HARN MAG CONT IN WIRE HARN TIMER A WIRE HARN TIMER B WIRE HARN TIMER C WIRE HARN MAG CONT OUT WIRE HARN PWR SPLY OUT A WIRE HARN PWR SPLY OUT B 139 www seuservice com ASSY I O BASE DX FRI 4200 NOTE Make sure that there is no wiring etc in the slash mark portions ITEM NO PART NO DESCRIPTION NOTE 1 4201 WOODEN I O BASE 2 837 13844 CONTROL 2 FOR JVS 3 839 1148 4A DC SSR BD 4 839 1011 SSR 1EA BD 101 280 5009 01 CORD CLAMP 21 102 280 0419 HARNESS LUG 103 601 7467 L LOCK BK 104 400 5368 15024 SW REGU 1 1508 24 105 601 0460 PLASTIC TIE BELT 100 MM 106 270 5052 04 L FILTER D 201 011 P00325 TAP SCR PH 3 X 25 202 011 F00310 TAP SCR FH 3 X 10 203 011 T03512 TAP SCR TH 3 5 X 12 204 011 T03516 TAP SCR TH 3 5 X 16 205 000 P00308 W M SCR PH W FS M3 X8 301 FRI 60023 WIRE HARN I O AC IN 302 FRI 60025X WIRE HARN I O 303 FRI 60026 WIRE HARN I O DC IN 304 FRI 60027 WIRE HARN I O ANALOG www seuservice com 140 D 1 2 ASSY AUDIO BASE DX FRI 4300 02 9 2 AS ca 80 70 i Fa E 7 px NOILISOd TVNINAAL 800 00 408 GC 1 141 ASSY AUDIO BASE FRI 4300 D 2 2 ITEM NO 101 102 103 104 105 106 107 108 109 110 111 112 113 114 201 202 203 204 205 206 207 208 301 302 303 304 305 306 307 308 309 31
62. Z M5 X 10 HEX SKT H CAP SCR BLK OZ M5 X 25 HEX SKT H CAP SCR BLK OZ M6 X 15 M SCR FH M4 X 6 SET SCR HEX SKT CUP P M4 X 6 SPR WSHR M4 SPR WSHR M5 SPR WSHR M6 FLT WSHR M5 UNUT 5 HEX NUT M8 STP RING BLK OZ S14 WIRE HARN SHIFT SW 116 NOTE 3 3 07 ASSY SIDE TOWER FRI 3050 D 1 2 A portion Details of PART A 117 www seuservice com 07 ASSY SIDE TOWER FRI 3050 ITEM NO 00 10 tA Q 101 102 201 202 203 301 302 PART NO FRI 3051 FRI 3052 FRI 3053 FRI 3054 253 5457 421 7501 18 440 WS0002XEG 440 WS0012XEG 390 6649 32 390 6650 32EX 000 T00425 0B 011 T00312 000 T00412 0B FRI 60084 FRI 60085 www seuservice com 2 2 DESCRIPTION NOTE SIDE TOWER L SIDE FL COVER L SASH FRONT L WOODEN BASE FOR BRST FL HOLDER STICKER FL32W STICKER W POWER OFF ENG STICKER W HIGH TEMP ENG GLOW amp BALLAST UNIT 1P 32W FL 32WEX W CONN LOW W O G amp B SCR TH BLK 25 TAP SCR TH 3 12 M SCR TH BLK M4 X 12 WIRE HARN SIDE TOWER L INV IN WIRE HARN SIDE TOWER L FL 118 ASSY SIDE TOWER R FRI 3060 D 1 2 Details of PART A 50 5 119 www seuservice com ASSY SIDE TOWER FRI 3060 ITEM NO 00 10 101 102 201 202 203 301 302 FRI 3061 FRI 3062 FRI 3063 FRI 3054 253 5457 421 7501 18 440 WS0002XEG 440 WS0012XEG 390 6649 32 390 6650 32EX 000 T00425 0B 011 T0
63. aid high tension voltage can be discharged causing a very hazardous situation Therefore under no circumstances should it be disassembled 49 www seuservice com Static Electricity Touching the CRT surface sometimes causes you to slightly feel electricity This is because the CRT surfaces are subject to static and will not adversely affect the human body Installation and removal CAUTION Ensure that the Magnetizer Coil FBT Fly Back Transformer Anode Lead and Focus Lead are not positioned close to the sheet metal work s sharp edges etc and avoid damaging the insulated portions so as not to cause electric shock and malfunctioning For the name of parts refer to the above Figures www seuservice com 50 For the purpose of static prevention special coating is applied to the CRT face of this product To protect the coating pay attention to the following points CAUTION Damaging the coating film can cause electric shock to the customers Do not apply or rub with a hard item a rod with pointed edge pen etc to or on the CRT surfaces Avoid applying stickers seals etc on the CRT face Aluminum Foil Do not remove aluminum foils from the CRT corners Removing the aluminum foils can cause static prevention effects to be lowered 14 2 CAUTIONS TO BE HEEDED WHEN CLEANING THE CRT SURFACES Static preventive coating is applied t
64. cal Specifications can cause a fire and electric shock Be sure to independently use the power supply equipped with the Earth Leakage Breaker Using a power supply without the Earth Leakage Breaker can cause an outbreak of fire when earth leakage occurs Putting many loads on one electrical outlet can cause generation of heat and a fire resulting from overload When using an extension cord ensure that the cord is rated at 15 or higher AC 100 120V area and 7A or higher AC 220 240V area Using a cord rated lower than the specified rating can cause a fire and electric shock www seuservice com 2 Electric current consumption MAX 8 70 A AC 110V 50 Hz MAX 8 30 A AC 110V 60 Hz MAX 7 70 A AC 120V 60 Hz MAX 4 50 A AC 220V 50 Hz MAX 4 30 A AC 220V 60 Hz MAX 4 20 A AC 230V 50 Hz MAX 4 00 A AC 230V 60 Hz MAX 4 10 A AC 240V 50 Hz MAX 3 90 A AC 240V 60 Hz MAX 8 30 A For TAIWAN For transporting the machine into the location s building the minimum necessary dimensions of the opening of doors etc are 1 2m W and IMPORTANT 1 7m H For the operation of this machine secure a minimum area of 2 49m W X 3 16m D For ventilation provide an approximately 20cm space between the rear part of the cabinet and the wall 3 www seuservice com 3 OPERATION PRECAUTIONS TO BE HEEDED BEFORE STARTING THE OPERATION To av
65. ccumulated statics by touching grounded metallic surfaces etc IMPORTANT Put the Game Board in the Carton Box an accessory together with the Shield Case when requesting for the replacement or repair Transporting the Game Board in an undesignated status for replacement repair is unacceptable 18 1 TAKING OUT THE BOARD 7 Turn power off 2 Take out the 2 truss screws unlock and remove the Back Door Lower 0 Disconnect all of the Connectors connected to ASSY MAIN BOARD 2 Remove the 2 Wing Bolts take out ASSY MAIN BD DX with the Shield Case as is mounted FIG 18 1a WING BOLT 2 15 25 flat washer used TRUSS SCREW 2 X 30 flat washer used Cl n 71 www seuservice com CONNECTING THE VIDEO SIGNAL LINE AND AUDIO SIGNAL LINE SPEAKER AUDIO1 MONITOR LEFT RGB3 MONITOR RIGHT RGB4 FIG 18 1b SPEAKER AUDIO2 MONITOR CENTER RGB2 18 2 COMPOSITION OF GAME BOARD GAME BD FRI DX USA 833 13841 01 USA GAME BD FRI DX EXP 833 13841 02 OTHERS GAME FRI DX KOR 833 13841 03 KOREA GAME BD FRI DX AUS 833 13841 04 AUSTRALIA PHOTO 18 2 DIP SW SETTING In the product set all of the DIP SWes to OFF FIG 18 2 www seuservice com 72 19 DESIGN RELATED PARTS For the Warning Display stickers refer to Section 1 FRI 3052 SIDE FL COVER L FRI 3062 SIDE FL COVER R OPPOSITE SIDE a FRI 0501
66. ch undesignated places Touching places not specified can cause electric shock or short circuit 7 Take out the 2 truss screws remove the Front Cover from the Accel amp Brake Unit FIG 11 1 Loosen the screw which secure the Potentiobase and adjust the Volume value by moving the Base FIG 11 1b 0 Secure Potentiobase 4 Perform Volume setting in the Volume setting mode TRUSS SCREW 2 x 8 chrome T FIG 11 1a SCREW COVER 5 X 12 w flat amp spring washers POTENTIOBASE 220 5484 FIG 11 1b 220 5373 39 www seuservice com REPLACING THE VOLUME TRUSS SCREW 2 M4X8 k Drum the power off 2 Take out the 2 screws and remove the Potentiocover FIG 11 1 0 Disconnect the connector of the Volume to be replaced 4 Remove the screw which secures the Potentiobase FIG 11 1 b Remove the Potentiobase together with the Volume as is attached FIG 11 1 c 6 Remove the Base and Gear to replace the Volume 7 Adjust the Volume as per the previous page after replacing 11 2 GREASING POTENTIOBASE Be sure to use the designated grease Using undesignated grease can cause parts damage IMPORTANT Once every 3 months apply greasing to the Spring and Gear mesh portion For spray greasing use GREASE MATE PART No 090 0066 GREASING FIG 11 2 www seuservice com 40 12
67. ct the Earth Termi nal to the accurately grounded indoor earth terminal by using an earth wire Unless the product is grounded appropriately the user can be subject to electric shock After performing repair etc for the Control equipment ensure that the Earth Wire is firmly connected to the Control equipment Q Ensure that the Power Supply used is equipped with an Earth Leakage Breaker This product does not incorporate the Earth Leakage Breaker Using a power supply which is not equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs O Be sure to use fuses which meet the specified rating only for the machines which use fuses Using fuses exceeding the specified rating can cause a fire and electric shock Specification changes removal of equipment conversion and addition not designated by SEGA are not allowed The parts of the product include warning labels for safety covers for personal protection etc It is very hazardous to operate the product by removing parts and or modifying the circuits Should doors lids and protective parts be damaged or lost refrain from operating the product and contact where the product was purchased from or the office herein stated SEGA shall not be held responsible for any accidents compensation for damage to a third party resulting from the specifications not designated by SEGA Ensure that the product meets the requirements of appropriate Electrical Specifications B
68. ctions given below Note that the caution warning symbol marks and letters are used in the instructions Indicates that handling the monitors Indicates that handling the monitors by erroneously by disregarding this warning may disregarding this caution may cause a cause a potentially hazardous situation potentially hazardous situation which could which could result in death or serious injury result in personal injury and or material CAUTION Gamage Indicates that access to a specific part of the Indicates the instruction to disconnect a equipment is forbidden power connector or to unplug When performing such work as installing and removing the monitor inserting and disconnecting the external connectors to and from monitor interior and the monitor be sure to disconnect the power connector plug before starting the work Proceeding the work without following this instruction can cause electric shock or malfunctioning Using the monitor by converting it without obtaining a prior permission is not allowed SEGA shall not be liable for any malfunctioning and accident caused by said conversion Primary side and Secondary side The monitor s circuit which is divided into the Primary side SECONDARY SIDE and Secondary side is electrically isolated Do not touch the Chassis CRT primary side or do not touch both the primary side and the secondary side simultaneously Failing to observe the PRIMARY instruction can cause electric s
69. d securely connected Unless connected in the correct direction connector connections can not be made accurately Do not insert connectors forcibly L Do power cords have cuts and dents L Do the fuses used meet specified rating Is the Circuit Protector in an energized status Are all accessories available L Can all Doors and Lids be opened with the Accessory keys Can Doors and Lids be firmly closed TABLE OF CONTENTS BEFORE USING THE PRODUCT BE SURE TO READ THE FOLLOWING TABLE OF CONTENTS INTRODUCTION OF THE OWNER S MANUAL cy gy o 10 12 13 14 15 16 17 18 19 20 21 22 HANDLING PRECAUTIONS tr enne rr tentent Eee ve ge 1 PRECAUTIONS CONCERNING INSTALLATION LOCATION ee 2 3 OPERATION s aqna tr nite 4 5 NAME OE PARTS rentre aeta bri a o RAS REDES pano na 6 ACCESSORIES inerti itte 7 9 ASSEMBLING AND INSTALLATION 530 ettet trt ER HIERHER EHE IHE 10 19 PRINTER OPTIONAL ia apa pied ie unas et de begins 20 7 1 OPERATION WITH THE PRINTER ATTACHED 20 21 7 2 SETTING THE ROLL PAPER ttti tte heparin 21 24 7 23 CLEANING OF THE PRINTER HEAD iss rer rris 25 7 4 COUNTERMEASURES AGAINST PAPER JAM 26 PREC
70. d to an electric shock and the product s functioning may not be stable Ensure that the power cord and earth wire are not exposed on the surface passage etc If exposed they can be caught and are susceptible to damage If damaged the cord and wire can cause electric shock and short circuit accidents Ensure that the wiring position is not in the customer s passage way or the wiring has protective covering After wiring power cord on the floor be sure to protect the power cord Exposed power cord is susceptible to damage and causes an electric shock accident The AC Unit is mounted on the rear of the machine The AC Unit has Main SW Circuit Protector and the Inlet which connects the Power Cord 1 Ensure that the SW is OFF D gt MAIN SW 1 EARTH TERMINAL Connect with the indoor earth terminal 6 Main SW off CIRCUIT PROTECTOR D O AC Cable Power Cord O Ts D O FIG 6 4 AC unit INLET www seuservice com 16 2 Connect one end of the earth wire to the AC Unit Connect the Earth Wire earth terminal and the other end to the indoor earth to the Earth Terminal terminal The AC Unit earth terminal has a Bolt and Nut combination Take off the Nut pass the end of earth wire through the Bolt and fasten the Nut Note that the Earth Wire is incorporated in the Power Cord for the Areas of AC 120V
71. e 2 screws from the Monitor Board Lid on top of the monitor and the Adjustment Board appears TRUSS SCREW 2 blackM4 X 10 Monitor Board Lid PHOTO 14 3 For adjustment use the Resinous Adjustment Rod FIG 14 3 www seuservice com 52 OPERATION 1 Press the MODE button to display OSD The right hand end numeral indicates INPUT FRE QUENCY IN OUT MODE Example 31 kHz Input V POSI 31 051 OSD Display 2 Press the MODE button to select the adjustment item Each time the MODE button is pressed the OSD display shifts sequentially in order of V POSI A H POSI A V SIZE A H SIZE A CONTRAST A BRIGHT A DEGAUSS A RESET A OSD display disappears Press the DOWN button while pressing the MODE button to return the adjustment item to the preceding one 0 Adjust with UP button and DOWN button 4 To exit from OSD keep pressing the MODE button until the OSD display disappears V POSI The image s vertical position is adjustable V POSI H POSI H POSI The horizontal image s position is adjustable V SIZE The vertical image size is adjustable H SIZE The horizontal image size is adjustable CONTRAST Adjusts image contrast BRIGHT This adjusts the on screen image brightness DEGAUSS Degaussing is performed Once degaussed it takes approximately 4 minutes and 30 seconds to have degaussing function again Wait until the lower OSD display indicates PLEASE RESET Rese
72. e you purchased the product from and confirm the work procedures and obtain precautions prior to performing work Inappropriate parts replacement and or installing with erroneous adjustment can cause an overload or the parts to come into contact resulting in an electric shock a short circuit and a fire When adjusting the Volume be sure to use 2 workers 9 ADJUSTING OR REPLACING THE V R ADJUSTING THE VOLUME 1 Turn off power Take out 4 Truss screws to remove In cases the Steering operability is poor and the adjustment of VOLUME SETTING in the TEST mode is ineffective the causes may be the Volume Gear s mesh failure and or Volume malfunctioning By using the following procedure adjust Volume gear mesh or replace the Volume In this product when the Steering Wheel is moved fully left right if the Volume shaft is rotating within the movable range the Volume is not feared to be damaged Secure the Volume in the manner the Volume shaft is oriented as shown and the gears are appropriately engaged when the steering wheel is in the centering position allowing the car to go straight forward REAR LID Be sure to use 2 workers in adjust ing the Volume one is for operat ing the Steering Wheel and the other one for performing the adjustment the Rear Lid from the back of Front Cabinet At this time carefully support the Rear Lid as taking out the 4 Truss screws can cause the Rear Lid to drop PHOT
73. edal Steering Wheel Billboard Coin chute door Effect switch FIG 4 REAR VIEW TABLE 4 Wi X FRONT CABINET 2 080 mm X 780mm X 1 649 mm 401 kg REAR CABINET 1 190 mm X 1 480 mm X 1 649 mm 187 kg When assembled 2 080 mm X 2 260 mm X 1 833 mm 598 kg www seuservice com 6 5 ACCESSORIES When transporting the machine make sure that the following parts are supplied The printer is available in this product as an optional The printer prints Player s game results on the paper exclusively used for this product Contact where you purchased the product from and mention the following Kit No for an order Detailed installation method is explained in the Kit Manual contained in the Kit KIT XKT 0440 EX1 DESCRIPTION PRINTER KIT FOR FRI DX EXP TABLE 5 ACCESSORIES DESCRIPTION OWNERS MANUAL SERVICE MANUAL Part No Qty 420 6507 01 1 420 6508 01 1 Note Figures If Part No has no description the Number has not been registered or can not be registered Such a part may not KEY MASTER KEY be obtainable even if the customer desires to purchase it 220 5576 2 2 Therefore ensure that the part is in safekeeping with you For opening closing For the CASHBOX DOOR the doors AC Cable Power Cord 600 6729 1 AC 110V AREA 600 6695 1 AC 120V AREA 600 6618 1 AC 220 240V A
74. efore installing the product check for Electrical Specifications SEGA products have a nameplate on which Electrical Specifications are described Ensure that the product is compatible with the power supply voltage and frequency requirements of the location Using any Electrical Specifications different from the designated Specifications can cause a fire and electric shock Install and operate the product in places where appropriate lighting is available allowing warning labels to be clearly read To ensure safety for the customers labels and printed instructions describing potentially hazardous situation are applied to places where accidents can be caused Ensure that where the product is operated has sufficient lighting allowing the warnings to be read If any label is peeled off apply it again imme diately Please place an order with where the product was purchased from or the office herein stated When handling the Monitor be very careful Applies only to the product w monitor Some of the monitor TV parts are subject to high tension voltage Even after running off power some portions are still subject to high tension voltage sometimes Monitor repair and replacement should be performed only be those technical personnel who have knowledge of electricity and technical expertise Be sure to adjust the monitor projector properly Applies only to the product w monitor Do not operate the product leaving on screen flickering or blurring as it
75. electronic assemblies electromechanicals servicing control spare parts etc as regards the product F355 CHALLENGE DX TYPE This manual is intended for the owners personnel and managers in charge of operation of the product Operate the product after carefully reading and sufficiently understanding the instructions If the product fails to function satisfactorily non technical personnel should under no circumstances touch the internal system Please contact where the product was purchased from Use of this product is unlikely to cause physical injuries or damages to property However where special attention is required this is indicated by a thick line the word IMPORTANT and its sign in this manual Indicates that mishandling the product by disregarding this display can cause the product s intrinsic performance not to be obtained resulting in malfunctioning IMPORTANT SEGA ENTERPRISES INC U S A CUSTOMER SERVICE 45133 Industrial Drive Fremont California 94538 U S A Phone 415 701 6580 Fax 415 701 6594 DEFINITION OF LOCATION MAINTENANCE MAN AND SERVICEMAN WARNING Non technical personnel who do not have technical knowledge and expertise should refrain from performing such work that this manual requires the location s maintenance man or a serviceman to carry out or work which is not explained in this manual Failing to comply with this instruction can cause a severe accident such as electric shock
76. gt RJ 17 77 7 GRIP FIG 8c 28 Do not push glass made or plastic parts www seuservice com Precautions concerning applying a rope SHIPPING BRACKET REAR Position designation of Forklift s Fork to be inserted ET 249 7 Z IPEN S V NS y FORK INSERTION POSITION STICKER Do not apply a rope to Handle or Lever Use protective materials to the places the rope is applied to Caution when transporting the machine www seuservice com 29 9 HANDLE MECHA WARNING 5 IMPORTANT Before starting to work ensure that the Power SW is OFF Failure to observe this can cause electric shock or short circuit Use care so as not to damage wirings Damaged wiring can cause electric shock or short circuit Do not touch undesignated places Touching places not designated can cause electric shock or short circuit This work should be performed by the Location s Maintenance Man or Serviceman Performing work by non technical personnel can cause electric shock hazard Do not insert hand into the mechanism so as not to cause hand and fingers pinched in Failure to observe this can cause a serious injury such as a fracture When performing work such as parts replacement other than those specified in this manual be sure to contact wher
77. he washers used underneath the Bushes 16 TRUSS SCREW 2 G Replace the Fluorescent Lamp das BUSHE FL PLATE M4 SSSSSs FIG 15b PLATE HOLDER FLUORESCENT LAMP 20W 390 5251 20 01 GLOW BULB 390 5638 1E When performing work be sure to use a step 59 www seuservice com THE REAR SIDE 7 Turn off power Take out 8 Truss screws TRUSS 8 M4 X 12 flat washer used 0 Remove the FL Cover Rear 2 Replace the Fluorescent Lamp PHOTO 15 FLUORESCENT LAMP 30W 390 525 1 30 01 GLOW BULB 390 5638 1E PHOTO 15b www seuservice com 60 SLIM LAMP SASH REAR Remove the FL Cover Rear as per procedures in THE REAR Take out 4 screws of the FL Cover Rear installing portion where the Slim lamp to be replaced is attached SCREW 4 M4 X 16 w flat amp spring washers 0 Remove the Sash Rear 4 Take out 2 screws 5 Remove the Rear Window PHOTO 15 REAR WINDOW TRUSS SCREW 2 12 lj li 3 3 d PHOTO 154 www seuservice com 61 Remove the Comer Plate When it CORNER LIGHT LID is hard to remove the Corner Plate 390 6651 loosen the 5 screws which secure the Corner Light Lid 5 e CORNER PLATE Take out 2 screws which secure the Bracket of connector side of Pd the Slim lamp P d Disconnect the connector and CONNECTOR replace
78. hock and this is very SIDE dangerous When making monitor adjustments use a non conductive driver and make adjustment without touching part other than the Adjustment V R and knob Also be sure not to cause a short circuit to the Primary side and Secondary side If short circuited it can cause electric shock or malfunctioning which is very dangerous High tension Voltage Some of the parts inside monitor are subject to high tension voltage in excess of 20 000 volts and very dangerous Therefore do not touch the monitor interior Should soldering amp paper wastes etc be mixed in the monitor interior turn the power off so as not to cause malfunctioning or fire hazard voor CAP PRIMARY SIDE DEMAGNETIZER REAR PART COIL ANODE LEAD Approx 29 kV DEMAGNETIZER NUN FOCUS LEAD COIL black Approx 10 kV Chassis sheet metal work CRT etc SECONDARY SIDE Disconnect or unplug Connecting CRT and PCB For combining the CRT and PCB use the specified part No to maintain the status of adjustments made at the factory The anode of the CRT itself will be accumulatively charged as time elapses generating high tension voltage which is very dangerous The monitor should be used with the Chassis CRT and PCB assembled When repair etc is required at the time of malfunctioning be sure to send it in an as is assembled condition If these are disassembled what s charged to s
79. is Using the product with the monitor not properly adjusted may cause dizziness or a headache to an operator a player or the custom ers When transporting or reselling this product be sure to attach this manual to the product In the case where commercially available monitors and printers are used in this product only the contents relating to this product are explained herein Some commercially available equipment has functions and reactions not stated in this manual Read this manual together with the specific Instruc tion Manual of such equipment Descriptions herein contained may be subject to improvement changes without notice The contents described herein are fully prepared with due care However should any question arise or errors be found please contact SEGA INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION OOOO Normally at the time of shipment SEGA products are in a status allowing for usage immediately after transporting to the location Nevertheless an irregular situation may occur during transportation Before turning on power check the following points to ensure that the product has been transported in a satisfac tory status Are there any dented portions or defects cuts etc on the external surfaces of the cabinet Are Casters and Adjusters damaged Do the power supply voltage and frequency requirements meet with those of the location Are all wiring connectors correctly an
80. llation position 2 Put each of Roof Nut Plates F amp R on to the fixed portion of the Center Roof front and rear and secure with 3 Truss screws for each 0 Remove the Shipping Bracket Rear from the Rear Cabinet s ceiling Remove the 2 pairs of Tamperproof screws and Hexagon Bolts 4 Secure the Billboard with 2 Tamperproof screws separately packed and 2 flat washers which previously secured the Shipping Bracket Rear ROOF NUT PLATE F CENTER ROOF ROOF NUT PLATER BILLBOARD TAMPERPROOF SCREW 2 8 X 30 SHIPPING BRACKET REAR TRUSS SCREW 3 each M6 X 30 flat washer used HEXAGON NUT 8 washer used TAMPERPROOF SCREW 2 M8 X 30 flat washer used FIG 6 2 www seuservice com 14 E SECURING IN PLACE ADJUSTER ADJUSTMENT WARNING Make sure that all of the adjusters are in contact with the floor If they are not the cabinet can move and cause an accident This product has 8 casters 4 for Front Cabinet 4 for Rear Cabinet and 8 Adjusters 4 for Front Cabinet 4 for Rear Cabinet FIG 6 3a When the installation position is determined cause the adjusters to come into contact with the floor directly make adjustments in a manner so that the casters will be raised approximately 5mm from the floor and make sure that the machine position is level Transport the product to the installation position Be sure to provide adequate space allo
81. n slot Feed the Roll Paper tip through the exit slot straight by hand until the paper tip can be seen from the exit slot Pull up the Head Up Lever D Turn on power The Printer performs automatic feeding AUTO LOADING and cutting of the paper 2 Put the ASSY Printer and lock the printer door to secure www seuservice com 26 8 PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE WARNING CAUTION gt IMPORTANT When moving the machine be sure to unplug the power plug Moving the machine with the plug as is inserted can damage the power cord and cause fire and electric shock hazards When moving the machine on the floor retract the Adjusters and ensure that Casters make contact with the floor During transportation pay careful attention so that Casters do not tread power cords and earth wires Damaging the power cords can cause electric shock and short circuit hazards When lifting the cabinet be sure to hold the grip portions or bottom part Lifting the cabinet by holding other portions can damage parts and installation portions due to the empty weight of the cabinet and cause personal injury In the case the cabinet is separated into the front and rear portions do not push the upper rear part of the front cabinet Failure to observe this causes the front cabinet to fall down towards the monitor side and result in accidents and injury to persons When moving the front cabinet in the above case be sure to
82. n the carton box Positioning the Shield Case upside down or packing in the manner different from what is shown in this Figure can cause the Game Board and other parts to be damaged 9 www seuservice com 6 ASSEMBLING AND INSTALLATION Perform assembly work by following the procedure herein stated Failing to comply with the instructions can cause electric shock hazard Perform assembling as per this manual Since this is a complex machine erroneous assembling can cause an electric shock machine damage and or not functioning as per specified performance When assembling be sure to use plural persons Depending on the assembly work there are some cases in which working by one person alone can cause personal injury or parts damage Ensure that connectors are accurately connected Incomplete connections can cause electric shock hazard Be careful so as not to damage wirings Damaged wiring can cause electric shock and short circuit hazards In the case the cabinet is separated into the front and rear portions do not push the upper rear part of the front cabinet Failure to observe this causes the front cabinet to fall down towards the monitor side and result in accidents and injury to persons When moving the front cabinet in the above case be sure to push it from side directions and move it by 2 or more persons for safety This work should be performed by the Location s Maintenance Man or Serviceman Performing work by non technical pe
83. o the steering wheel reaction during the game reaction at the time of a course out or crashing can not be obtained correctly In case of an abnormal reaction during the game turn the power on again from the beginning and complete the power on check In this product once the power is turned off the data of inserted coins less than one credit and BONUS ADDER is cleared As the exclusively used paper is not supplied to the Printer at the time of shipment the message Printer unavailable is displayed on the Advertise screen and the 2 red Lamps of the Rear Cabinet back side light up FIG 6 5 www seuservice com 18 4 ASSEMBLING CHECK In the TEST mode ascertain that the assembly has been made correctly IC BD is satisfactory and the screen adjustment is appropriate For details refer to the SERVICE MANUAL In the test mode perform the following test MEMORY TEST The on board memory is tested automatically CRT TEST The screen on which the monitor is adjusted is displayed INPUT TEST Each switch and V R are tested OUTPUT TEST The lamp motor etc are tested SOUND TEST The sound related BD and wiring connections are tested Be sure to check if the sound is satisfactorily emitted from each speaker and the sound volume is appropriate Perform the above inspections also at the time of monthly inspection 19 www seuservice com 7 PRINTER OPTIONAL Refer to this section only when the Printer optional i
84. o the CRT surfaces When cleaning pay CAUTION attention to the following points Peeling off of static preventive coat can cause electric shock Remove smears by using a dry soft cloth flannels etc Do not use a coarse gauze etc For smear removing solvent alcohol ethanol is recommended When using chemical detergent be sure to follow instructions below Dilute chemical detergent with water and dip a soft cloth in and then thoroughly wring it to wipe smears off Do not use a chemical detergent containing an abradant powder or bleaching agent Do not use alkaline chemical detergents such as glass cleaner available on the market or solvents such as thinner etc Do not rub or scratch the CRT face with hard items such as brushes scrub brush etc Clean the CRT surfaces once a week When cleaning pay attention to the above caution so that the antistatic coating will not come off 51 www seuservice com 14 3 ADJUSTMENT METHOD Monitor adjustments have been made at the time of shipment Therefore do not make further adjustment without a justifiable reason Adjusting the WARNING monitor which contains high tension parts is a dangerous work Also an erroneous adjustment can cause deviated synchronization and image fault resulting in malfunctioning When making adjustment utilize a resinous Alignment Rod Servicing with bare hand or using conductive tools can cause electric shock Remove th
85. ock be sure to turn power off and unplug from the socket outlet before performing work by touching the internal parts of the product Be careful so as not to damage wirings Damaged wiring can cause electric shock and short circuit accidents Be sure to use fuses meeting specified rating Using fuses exceeding the specified rating can cause fire and electric shock accidents After eliminating the cause of the blowing of fuse replace the fuse Depending on the cause of fuse blowing continued use with the fuse as is blown can cause generation of heat and fire hazard Take out 2 screws to remove Side Door R and the fuse appears as shown www seuservice com FUSE 6 3A 250W SPEAKER V R Use the setting of Adjust Volumes shown as is the time of shipment TRUSS SCREW 2 black X 30 flat washer used SIDE DOORR FIG 17 70 18 GAME BOARD WARNING In order to prevent electric shock and short circuit hazards be sure to turn power off before performing work Be careful so as not to damage wirings Damaged wiring can cause fire electric shock and short circuit hazards Do not expose the Game BD etc without a good reason Failure to observe this can cause electric shock or malfunctioning CAUTION The electronic parts on the IC Board could be damaged due to human body s static electricity Before performing IC Board related work be sure to discharge physically a
86. oduct by disregarding this by disregarding this caution will cause warning will cause a potentially a slight hazardous situation which can WARNING hazardous situation which can CAUTION result in personal injury and or material result in death or serious injury damage For the sage usage of the product the following pictographs are used Indicates HANDLE WITH CARE In order to protect the human body an equipment this display is attached to places where the Owner s Manual and or Service Manual should be referred to Q Perform work in accordance with the instructions herein stated Instructions for work are explained by paying attention to the aspect of accident prevention Failing to perform work as per the instructions can cause accidents In the case where only those who have techni cal expertise should perform the work to avoid hazardous situation the instructions herein state that the serviceman should perform such work O Be sure to turn off power before working on the machine To prevent electric shock be sure to turn off power before starting the work in which the worker touches the interior of the product If the work is to be performed in the power on status the Instruction Manual herein always states to that effect Be sure to ground the Earth Terminal this however is not required in the case where a power cord with earth is used This product is equipped with the Earth Terminal When installing the product Conne
87. oid injury and trouble be sure to constantly give careful attention to the behavior and manner of the visitors and players A In order to avoid accidents check the following before starting the operation Check if all of the adjusters are in contact with the surface If they are not the WARNING Cabinet can move and cause an accident ig Ensure that all of the Adjusters are in contact with the floor Do not put any heavy item on this product Placing any heavy item on the product can cause a falling down accident or parts damage Do not climb on the product Climbing on the product can cause falling down accidents To check the top portion of the product use a step To avoid electric shock check to see if door amp cover parts are damaged or omitted To avoid electric shock short circuit and or parts damage do not put the following items on or in the periphery of the product Flower vases flowerpots cups water tanks cosmetics and receptacles containers vessels containing chemicals and water To avoid injury be sure to provide sufficient space by considering the potentially crowded situation at the installation location Insufficient installation space can cause the customers to come into contact with or hit the others and result in injury or trouble CAUTION www seuservice com 4 PRECAUTIONS TO BE HEEDED DURING OPERATION PAYING ATTENTION TO CUSTOMERS WARNING CAUTIO
88. omplete the power on check incorrect Deviation of Center V R position deviated Adjust V R value in the test mode see Service Manual Steering Wheel Reaction Mecha s secular change Adjust V R value in the Test mode reaction strength is see Service Manual insufficient Paddle Shift s Switch malfunctioning Replace the Switch see 9 3 operation is not satisfactory 6 speed Shift s Switch malfunctioning Replace the Switch see Sec 9 operation is not satisfactory Operation of Accel V R malfunctioning Replace the V R see Sec 11 and Brake Pedals are not satisfactory ADJUST GEAR s engagement is not Adjust the engagement of ADJUST GEAR correct see Sec 11 Crutch Pedal s V R malfunctioning Replace the V R see Sec 12 operation is not satisfactory ADJUST GEAR s engagement is not Adjust the engagement of ADJUST GEAR correct see Sec 12 Fluorescent lamp Fluorescent lamp needs replacement Replace the fluorescent lamp see Sec 15 doesn t light up CIRCUIT PROTECTOR SIDE DOOR R TRUSS SCREW 2 4 X 30 flat washer used FIG 17 b 69 www seuservice com REPLACMENT OF FUSE WARNING Fuse replacements other than those specified can cause accidents and are strictly forbidden In case fuse replacements other than those stated in this manual are necessary contact where you purchased the product from for inquiries regarding this matter In order to prevent an electric sh
89. ough where the product was purchased from or the office herein stated Using the cord as is damaged can cause fire electric shock or leakage Be sure to perform grounding appropriately Inappropriate grounding can cause an electric shock Be sure to use fuses meeting specified rating Using fuses exceeding the specified rating can cause a fire or electric shock Completely make connector connections for IC BD and others Insufficient insertion can cause an electric shock To avoid causing a fire or electric shock do not make Specification changes by removing converting and making additions unless otherwise designated by SEGA Be sure to perform periodic maintenance inspections herein stated For the IC board circuit inspections only the logic tester is allowed The use of a multiple purpose tester is not permitted so be careful in this regard When cleaning the CRT surfaces use a soft dry cloth Do not apply chemicals such as thinner benzine etc The electronic parts on the IC Board could be damaged due to human body s static electricity Before performing IC Board related work be sure to discharge physically accumulated statics by touching grounded metallic surfaces etc 1 www seuservice com 2 PRECAUTIONS CONCERNING INSTALLATION LOCATION WARNING This product is an indoor game machine Do not install it outside Even indoors avoid installing in places mentioned below so as not to cause a
90. rsonnel can cause a severe accident such as electric shock Failing to comply with this instruction can cause a severe accident such as electric shock to the player during operation Provide sufficient space so that assembling can be performed Performing work in places with narrow space or low ceiling may cause an accident and assembly work to be difficult WARNING When handling plastic parts use care Do not give a shock or apply excessive load to the fluorescent lamps and plastic parts Failure to observe this can cause CAUTION parts damage resulting in injury due to fragments cracks and broken pieces www seuservice com 10 When carrying out the assembling and installation follow the following 6 item sequence ASSEMBLING THE CABINET INSTALLING THE CENTER ROOF AND THE BILLBOARD SECURING IN PLACE ADJUSTER ADJUSTMENT POWER SUPPLY CONNECTION TURNING POWER ON ASSEMBLING CHECK fo fen The master key accessories in addition to the tools such as a Phillips type screwdriver wrench for M16 hexagon bolt socket wrench Ratchet Handle for M6 M8 hexagon bolt Tamperprooftwrench accessories are required for the assembly work Tj Phillips type screwdriver 24mm N WRENCH for M16 hexagon bolt SOCKET WRENCH for M6 M8 hexagon bolt RATCHET HANDLE TAMPERPROOFTWRENCH 0 Un KEY MASTER 11 www seuservice com ASSEMBLING THE
91. s attached Be sure to turn off power unless otherwise specified before performing work Performing work on the energized machine can cause hands or fingers to be CAUTION pinched in or in jured due to the machine s sudden move Do not touch undesignated places Failure to observe this may cause a burn due to the Head s high temperature when printing When performing work that uses the cutter be very careful so as not to cut hands or fingers unspecified parts can cause malfunctioning and or a damage to parts Be sure to use the new roll paper unwrapped immediately before the use IMPORTANT Using the roll paper previously unwrapped and left for a while can cause malfunctioning due to deterioration resulted from humidity When setting the paper with the power on if the paper volume is small the Printer might not accept the set roll paper In that case follow the SETTING THE PAPER WITH THE POWER OFF procedures to set the paper Gror Be sure to use the exclusively used paper and a Cleaning Pen Using When the Printer is malfunctioning the 2 Error Lamps attached to the Rear Cabinet back side flash or light up The Lamps flash when the paper is exhausted and light up when the trouble is other than the running out of paper 2 SA When placing an order contact where you purchased the product or the Printer Kit from in stating the _ following part number and the description The following
92. s so as not to put dust on the outlet for driving records Failure to observe this may cause a fire due to cigarette stubs This product is intended for Player only Playing the game by 2 or more Players riding on the seat together can cause falling down and collision accidents by striking head hand or elbow Immediately stop such violent acts as hitting and kicking the product Such violent acts can cause parts damage or falling down resulting in injury due to fragments and falling down To avoid collision or falling down accident caution the customers so as not to come in to the Seat rear Instruct the Player to take firm hold of the Steering Wheel when in play The Steering Wheel is equipped with reaction mechanism Holding the Steering Wheel lightly while playing the game can cause a contingent accident Instruct the customer other than the Player not to touch the operation device when in play Touching the operation device during play can cause accidents and trouble between customers Instruct the Player to adjust the seat before playing the game Playing the game in a forcible posture can cause a contingent accident This product is designed for players taller than 130cm and shorter than 210cm To avoid accidents instruct the customers who do not meet the height requirements to refrain from playing the game 5 www seuservice com 4 NAME OF PARTS 29 inch monitor Accel amp Brake Pedal Clutch P
93. slot Feed the Roll Paper tip through the exit slot straight by hand At this time if the Paper tip is in excess of the feeding point the automatic feeding of Paper is performed and the Paper is cut after feeding about one page long 9 Push down the Head Up Lever The feeding point of the Roll Paper tip FIG 7 21 Push down the Head Up Lever power The Printer starts automatic feeding of the paper AUTO LOADING and then cuts the paper automatically If the Paper tip position is appropriate as per previous procedure the automatic feeding s movement is slight and the paper cutting may not be done D Push the ASSY PRINTER into the point the PRINTER reaches the securing part in the innermost of the unit 3 Lock the Printer Door to secure www seuservice com 24 7 3 CLEANING OF THE PRINTER HEAD Each time the Roll Paper is supplied clean the Printer Head Prepare the cleaning pen which is included in the Print Paper Set exclusively used for this product and a Master Key 7 Turn off power Roll Paper Q Unlock with the Master Key and remove the Printer Door 0 Draw ASSY Printer toward you 4 Push up the Head Up Lever G Remove the Roll Paper 6 Push down the Cutter Lever and open the Auto Cutter 7 By using the cleaning pen clean the printer head Use the exclusively used Cleaning Pen FIG 7 3 Lift the Auto Cutter and lock 9 Set the Roll Paper Push down the
94. t the on screen setting status to the factory setting Press the UP button or DOWN button for one second or longer Note that the factory setting status is predetermined and not changeable 53 www seuservice com 14 4 CLEANING THE MONITOR GLASS Removing the Monitor Glass requires complicated work Clean the Front Glass only in the weekly cleaning To clean the Reverse Glass of the Monitor and the CRT Surface removing the Monitor Glass is required FRONT MONITOR GLASS 1 Take out 2 screws to remove the Boss Cover 0 Take out 10 screws to remove the Control Panel Upper If it is hard to take out the screws due to the existence of the Steering Wheel remove the emblem and the Steering Wheel ahead of time 0 Take out 4 screws to remove the Control Panel Bracket Upper 4 Take out a total of 6 screws and remove each of Glass Holder Upper Center Glass Holder Upper Lower and Glass Sash GLASS HOLDER UPPER CENTER GLASS SASH GLASS HOLDER LOWER CENTER GLASS SASH CONTROL PANEL BRACKET UPPER CONTROL PANEL UPPER N TRUSS SCREW 6 in total black M4 X 16 flat washer used SCREW 4 M4 X 16 w flat amp spring washers Gm of BOSS COVER x TRUSS SCREW 10 black 7 4 12 flat washer used TRUSS SCREW 2 black M4 X 8 FIG 14 4 G Take out the Monitor Glass 2 FIG 14 4 b MONITOR GLASS www seuservice com 5
95. the Slim lamp P Pd 9 Insert the edge of the replacing Slim lamp in to the holder 4 x 42 m Pass the plastic made bush and 22 5 274 spacer through the 2 screws which 22 d secure the Bracket of the connector Ge side Install in a manner to put installation portion between the bush and the spacer EN nus SCREW 2 M4 X 12 flat washer used FIG 15 www seuservice com 62 ERROR LAMP To perform the following work a Phillips type Screwdriver and a driver for M4 Hexagon Nut are required CVmm 7 Turn off power Q Take out 2 screws 0 Remove the Socket Cover SCREW 2 8 SOCKET COVER PHOTO 15 f 4 Disconnect a connector Disconnect the connector PHOTO 15 g 63 www seuservice com G Take out 2 Flange Nuts 6 Remove the Lamp together with the Lamp Base FLANGE NUT 2 M4 PHOTO 15h 7 Replace the Lamp LAMP 110V 10W 390 5174 PHOTO 151 www seuservice com 64 REPLACING THE EFFECT SWITCH LAMP 1 Remove the Shift Cover as per procedures 10 1 Unlock the lock Q A metallic part is ejected from the switch base of the EFFECT SWITCH reverse side Turning the metallic part can unlock the lock Take off the wiring connecting portion from the switch PHOTO 15j PHOTO I5 k 0 The lamp is inside the wiring connecting portion Push and then turn the Lamp counterclockwise to remove LAMP 6 3V 1W 390 5445
96. the Volume engage the gears at the angular position shown and fix the VR Bracket VR BASE SCREW 2 12 w flat amp spring washers FIG 9 1b V R 220 5484 220 5373 Turn on power Set the Center Value of the Volume in the TEST mode In the TEST mode check to see if the Volume Value varies smoothly in accordance with the steering wheel operation 9 2 GREASING Be sure to use the designated grease Using undesignated grease can cause parts damage Do not apply greasing to undesignated places Failure to observe this can cause malfunctioning or quality deterioration of parts VOLUME GEAR MESH PORTION Apply greasing to gear mesh portions once every 3 months Use GREASE MATE SEGA PART NO 090 0066 PHOTO 9 2 33 www seuservice com 9 3 REPLACING PADDLE WING SHIFT SWITCH In case the Paddle Shift operability is poor malfunctioning of or a damage to the Microswitch inside the Paddle Shift can be considered PADDLE SHIFT 1 Tum off power BOSS COVER Q Take out 2 Truss screws for each to remove Boss Cover Upper and Lower 0 Disconnect the wiring connected to the Microswitch M4 X 8 PHOTO 9 3 www seuservice com 34 SCREW 2 M3 X 16 4 Take out 2 screws to replace the Microswitch 5 Adjust Microswitch s actuator to an angular position so as not to touch the Switch when operating the
97. urrent and functioned due to instantaneous reinstate the circuit protector to its original overcurrent status see Sec 6 CIRCUIT PROTECTOR inside the Reinstate the circuit protector to its original Cabinet functioned due to instantaneous status see FIG 17 b overcurrent The color of image Incorrect monitor adjustment Make appropriate adjustments see Sec 14 on MONITOR screen is incorrect The on screen The power source and voltage are not Make sure that the power supply and voltage image of the correct are correct monitor sways and or shrinks Sound is not Sound volume adjustment is not correct Adjust the SWITCH UNIT s sound emitted adjustment volume see Service Manual Malfunctioning BD and Amp Perform Sound Test to check it see Service Manual Connector connection is incorrect Check connectors between the Front and the Rear Cabinets see Sec 6 CIRCUIT PROTECTOR CIRCUIT PROTECTOR Functions due to the activation of bimetal To restore the function wait for approximately one minute or longer until the bimetal cools FIG 17a off Press the Button www seuservice com 68 TABLE 17 b PROBLEMS CAUSE COUNTERMEASURES No sound is emitted The Fuse is blown due to momentary Replace fuse see FIG 17 c from WOOFER overload 514 5086 6300 FUSE 6 4 30 6300mA 125W Steering Wheel Power ON check not performed Turn off power and then turn it back on reaction strength is correctly again C
98. wing the player to get on and off 2 Have all of the Adjusters make contact with the floor Adjust the Adjuster s height by using a wrench so that the machine position is kept level 0 After making adjustment fasten the Adjuster Nut upward and secure the height of Adjuster FIG 6 3 b ADJUSTER 2 Re FIG 6 3 Refer to this Fig Scale 1 100 for the layout of the place of installation CASTER FIG 6 3 a BOTTOM VIEW FASTEN UPWARD P d FIG 6 3 b ADJUSTER CASTER Approx 5mm A 1 g 21 si 22 FIG 6 34 Be sure to provide space as shown between the Air Vent and the wall surface 15 www seuservice com POWER SUPPLY AND EARTH CONNECTION Be sure to independently use the power supply socket outlet equipped with an Earth Leakage Breaker Using a power supply without an Earth Leakage WARNING Breaker can cause a fire when electric leakage occurs Ensure that the accurately grounded indoor earth terminal and the earth wire cable are available except in the case where a power cord plug with earth is used This product is equipped with the earth terminal Connect the earth terminal and the indoor earth terminal with the prepared cable If the grounding work is not performed appropriately customers can be subjecte
99. www seuservice com 2nd PRINTING AUG S Deluxe Version OWNER S MANUAL SEGA ENTERPRISES INC USA MANUAL NO 4201 6507 01 VISIT OUR WEBSITE E PERRIER cem SERVICE ne a E u m 01116 Ask Dave std M cad a E r 4 m a unas M S DES people have visited this page since 3 16 01 aa me If you have any questions or comments about this site please E Mail to Darl Davdsonf seu sega com E i Senece Department phere 415 m 5 Tas 415701 0506 Al Platforms Windows Macintosh BEFORE USING THE PRODUCT BE SURE TO READ THE FOLLOWING To maintain the safety To ensure the safe usage of the product be sure to read the following before using the product The following instructions are intended for the users operators and the personnel in charge of the operation of the product After carefully reading and sufficiently understanding the warning displays and cautions handle the product appropriately Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary Herein explanations which require special attention are enclosed with dual lines Depending on the poten tially hazardous degrees the terms of WARNING CAUTION etc are used Be sure to understand the contents of the displays before reading the text Indicates that mishandling the Indicates that mishandling the product pr
Download Pdf Manuals
Related Search
Related Contents
PROGRAMMATION HIVER Océ Colour Copy 5.0 - Océ - John Deere 本製品を使用する前に、付属の取扱説明書をお読みください。 また、安全 Parker Hannifin HD65 User's Manual HP ProLiant ML310 Server Setup Manual - RayBiotech, Inc. Eddy DK - Lysator Emerson (K580HC-K975A) Diagrams and Drawings H O T - Meilleur du Chef Copyright © All rights reserved.
Failed to retrieve file