SECO-LARM USA EV-122C-DXA3 User's Manual
Contents
1. harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipmentin a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARRANTY This SECO LARM product is warranted against defects in material and workmanship while used in normal service for a period of one 1 year from the date of sale to the original consumer customer SECO LARM s obligation is limited to the repair or replacement of any defective part if the unit is returned transportation prepaid to SECO LARM This Warranty is void if damage is caused by or attributed to acts of God physical or electrical misuse or abuse neglect repair or alteration improper or abnormal usage or faulty installation or if for any other reason SECO LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship The sole obligation of SECO LARM and the purchaser s exclusive remedy shall be limited to replacement or repair only at SECO LARM s option In no event shall SECO LARM be liable for any special collateral incidental or consequential personal or property damages of any Kind to the purchaser or a2. is to be mounted 2 Temporarily connect the camera to the 12VDC power supply 3 Temporarily connect the camera s female BNC connector to the video cable s male BNC connector 4 While watching the monitor hold the camera against the wall by hand where it is to be mounted then turn the camera until it is certain that this mounting location is correct Use a pencil to mark the location of the three screw holes in the base 5 Disconnectthe 12VDC power supply and video cable serviceable parts inside 7 Do not drop the camera or subject it to strong vibrations Note Many video monitors produce strong electromagnetic fields close to the display CRT especially when the monitor is turned on or during de Gaussing which occurs automatically with many monitors when the monitor is turned on 6 Mountthe bracket to the wall using the three included mounting screws If the wall is made of dry wall brick or similar material it may be necessary to use screw anchors not included 7 Reconnectthe 12VDC power supply and video cable Turn the monitor on and make sure the camera is Sending the proper video signal 8 Adjustthe camera angle 9 Putthe case over the camera ball and twist to secure to the base 10 Do a final test of the video camera and monitor Note The base also allows flush mounting of the camera However for the best security run the wires through the wall
3. ENFORCER BaLt Mount IR Dome Camera Manual TROUBLE SHOOTING The screen is blank Check that the camera is powered up Check that the monitor is powered up Check that the video cable connecting the camera to the monitor is connected properly Clean the lens using a soft clean cloth Check that the light source is adequate The screen image is dim The screen image has poor contrast Adjust the monitor s contrast knob Change the position of the camera The screen image flickers Change the position of the camera The screen image is distorted Change the position of the camera The camera case is hot Check that the correct power supply is in use IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national State and local laws and statutes related to monitoring and recording audio and video signals SECO LARM will not be held responsible for the use of this product in violation of any current laws or statutes WARNING Stop using the camera if you see a malfunction like smoke or unusual heat as it could cause fire or electric shock Do not open the case of this device as there are no field serviceable components inside FCC COMPLIANCE STATEMENT Information to the user This equipment has been tested and found to comply with the limits fora Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against
4. nyone else NOTICE The information and specifications printed in this manual are current at the time of publication However the SECO LARM policy is one of continual development and improvement For this reason SECO LARM reserves the right to change Specifications without notice SECO LARM is also not responsible for misprints or typographical errors Copyright 2007 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in part without the written permission of SECO LARM SECO LARM U S A Inc 16842 Millikan Avenue Irvine CA 92606 Weabsteswwwiseca aancon Z PITCW1 Tel 800 662 0800 949 261 2999 Fax 949 261 7326 E mail sales seco larm com iMUBallMountCam PMD MANUAL EV 122C DXA3 13 CCD Color Ball Mount IR Dome Camera SLI SECO LARM ENFORCER BaLt Mount IR Dome Camera Manual ee ag Specifications EV 122C DXA3 NTSC Type Color camera Chip 1 3 CCD Sony Resolution 420 TV lines Pickup elements 910 x 492 pixels Scanning system 2 1 interlace V 59 94Hz H 15 734KHz Sync Internal Video output 1V pp composite output 75 ohms Lens F1 2 3 6mm lens included IR LEDs 24 x LEDs IR distance Up to 50 15m 50 80 beam spread 30 per LED 0 05 lux 0 lux with IR on IR view angle Minimum illumination Gamma correction 0 45 S N ratio gt 50dB Shutter control Auto Electronic Shutter AES 1 60 1 100 000 sec Backlight compen
5. sation Auto Automatic gain control Auto White balance Auto 2500 9500 K Power source 12VDC 10 Power consumption 70mA IR off 280mA IR on Storage temperature 22 140 F 30 60 C Operating temperature 14 122 F 10 50 C Dimensions 3 16 x 21 16 93 x 69mm Weight 6 3 oz 180g Dimensions 2 hie 69mm lt x 31 4 93mm gt ENFORCER BaLt Mount IR Dome Camera Manual EVA F 5521 3 Optional power cord For easy connection of dome or bullet camera to power supply To BNC 3 ft wire length From DC EVA F 5521 3 Camera BEFORE STARTING Parts List 1 x Camera Ball 1 x Case 2 part construction 1 x Base 3 x Screws 1 x Manual Power 3 x Connector Screws DDAA mj Le i f BNC Connector 1 Please read this manual carefully and keep itfor future reference 6 Donotopen or disassemble the camera There are no user 2 Use the camera within given temperature and electrical limits 3 Do notmountthe camera where it is exposed to rain or other moisture orin humid or dusty places 4 Do notpoint the camera at the sun Heat could damage the camera even when notin use 5 Donotmountthe camera in areas exposed to radiation strong magnetic fields or strong electrical signals INSTALLATION 1 Runa 12VDC power supply wire and a video cable with a male BNC connector through the wall to where the camera
Download Pdf Manuals
Related Search