SECO-LARM USA EV-132C-DLW6Q User's Manual
Contents
1. Specifications EV 132C DWL8Q EV 135C DWL8Q EV 132C DWLDQ EV 135C DWLDQ EV 132C DWLHQ EV 135C DWLHQ Q Type Color camera Video format NTSC PAL Chip 1 3 CCD Sony Resolution 420 TV lines Pickup elements 512 x 492 pixels NTSC 512 x 582 pixels PAL Scanning system 2 1 interlace Sync Internal Video output 1V pp composite output 75 ohms EV 132C DWLDQ EV 135C DWLDQ 12mm EV 132C DWLHQ EV 135C DWLHQ 16mm EV 132C DWL6Q EV 135C DWL6Q 53 EV 132C DWL8Q EV 135C DWL8Q 39 EV 132C DWLDQ EV 135C DWLDQ 26 EV 132C DWLHQ EV 135C DWLHQ 19 0 1 lux LEDs off 0 0 lux LEDs on Viewing angle Minimum illumination Gamma correction 0 45 S N ratio gt 50dB AGC off Shutter control Auto Electronic Shutter AES 1 60 1 50 1 100 000 sec Backlight compensation auto Automatic gain control AGC auto Enclosure IP68 weatherproof of infrared LEDs 24 Max LED range Approximately 80 25m 12VDC 10 100mA IR off 360mA IR on 14 131 F 10 59 C 3 16 L x 21 4 D 78 x 57 mm without sunshield Weight 16 oz 454g All viewing angles are approximate Power source Power consumption Operating temperature Dimensions Dimensions 23 16 65mm 1 16 46mm ENFORCER Kee 31 16 78mm 16 14 5mm 2 57mm 2 16 68mm ENFORCER 24 LED CCD IR Day NiGcHt Camera MANUAL A Camera F BNC connector female P2. 1 Run a 12VDC power supply wire and a video cable with a male 7 Mount the bracket to the wall using the three included mounting BNC connector through the wall to where the camera is to be mounted if necessary Assemble the mounting bracket then screw it into the back of the camera Make sure the mounting base is tightened to the bracket Temporarily connect the camera to the 12VDC power supply Do not cut DC jack or video jack as warranty will be voided Use the included SECO LARM s pigtail connector Temporarily connect the camera s female BNC connector to the video cable s male BNC connector While watching the monitor hold the camera bracket against the wall by hand where it is to be mounted then twist the camera until it is certain that this mounting location is correct Use a pencil to mark the location of the three screw holes in the bracket Disconnect the 12VDC power supply and video cable screws If the wall is made of dry wall brick or similar material it may be necessary to use the three included screw anchors Reconnect the 12VDC power supply and video cable Turn the monitor on and make sure the camera is sending the proper video signal 9 Adjust the camera angle a Loosen and tighten the bracket s thumb screw to turn the camera and change its angle relative to the bracket This ensures the camera is pointing in the right direction b Loosen and tighten the adjustment plat
3. SECO LARM be liable for any special collateral incidental or consequential personal or property damages of any kind to the purchaser or anyone else NOTICE The information and specifications printed in this manual are current at the time of publication However the SECO LARM policy is one of continual development and improvement For this reason SECO LARM reserves the right to change specifications without notice SECO LARM is also not responsible for misprints or typographical errors Copyright 2007 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in part without the written permission of SECO LARM SECO LARM U S A Inc 16842 Millikan Avenue Irvine CA 92606 Website www seco larm com of PITNW1 Tel 800 662 0800 949 261 2999 Fax 949 261 7326 E mail sales seco larm com _ 1R_24LQseries_076 PMD ENFORCER VIDEO MANUAL 1 3 CCD Color IR Day Night Camera with 24 LEDs Video Lens Viewing Format Size Angle EV 132C DWL6Q EV 132C DWL8Q EV 132C DWLDQ NTSC 12mm EV 132C DWLHQ NTSC 16mm EV 135C DWL6Q PAL EV 135 DWL8Q PAL EV 135 DWLDQ PAL EV 135C DWLHQ PAL All viewing angles are approximate SLI SECO LARM RoHS Fe CE Note Products with model number that ends with Q or have a round green Q sticker represents RoHS compliant products r q ENFORCER 24 LED CCD IR Day NiGcHt Camera MANUAL EV 132C DWL6Q EV 135C DWL6Q
4. ENFORCER 24 LED CCD IR Day NiGcHtT Camera MANUAL TROUBLE SHOOTING The screen is blank Check that the camera is powered up Check that the power supply s polarity is correct Check that the monitor is powered up Check that the video cable connecting the camera to the monitor is connected properly The screen image is dim Clean the lens using a soft clean cloth Check that the light source is adequate The screen image has poor contrast Adjust the monitor s contrast knob Change the position of the camera The screen image flickers Change the position of the camera The screen image is distorted Change the position of the camera The camera case is hot Check that the correct power supply is in use IR LEDs do not turn on e Check that the correct power supply is in use IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national state and local laws and Statutes related to monitoring and recording audio and video signals SECO LARM will not be held responsible for the use of this product in violation of any current laws or statutes WARNING Stop using the camera if you see a malfunction like smoke or unusual heat as it could cause fire or electric shock Do not open the case of this device as there are no field serviceable components inside FCC COMPLIANCE STATEMENT Information to the user This equipment has been tested and found to comply with the l
5. arts List B Adjustable Sunshield G Adjustment nut C Mounting bracket H Mounting holes me eas gt A MOUNDS SOMES D 36 cord 1 x Sunshield 3 x Screw anchors E DC jack 1 x Mounting bracket 1x Manual 1 x Pigtail connector NOTE For additional pigtail connectors Important B inquire SECO LARM s EVA F5521 3Q Do not remove label or i pigtail connector with 3 f length cable open case as warranty will be voided Use SECO LARM s included Pigtail Connector for easy installation and serviceability Important N F eh Do not cut DC Jack E or Video Jack F as warranty ee will be voided BEFORE STARTING Please read this manual carefully and keep it for future reference Use the camera within given temperature and electricity limits Do not aim the LED light directly at the eyes when the LEDs are on Do not point the camera at the sun Heat could damage the camera even when not in use 5 Do not mount the camera in areas exposed to radiation strong magnetic fields or strong electrical signals 6 Do not open or disassemble the camera There are no user serviceable parts inside 7 Do not drop the camera or subject it to strong vibrations Note Many video monitors produce strong electromagnetic fields close to the display CRT especially when the monitor is turned on or during de Gaussing which occurs automatically with many monitors when the monitor is turned on e Ww N ee INSTALLATION
6. e to rotate the camera on its axis This rotates the angle of the video image 10 Tighten the bracket s thumb screw and the adjustment plate so that the camera does not move but not so tight that it cracks the case or bracket 11 Do a final test of the video camera and monitor
7. imits for a class a digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARRANTY This SECO LARM product is warranted against defects in material and workmanship while used in normal service for a period of one 1 year from the date of sale to the original consumer customer SECO LARM s obligation is limited to the repair or replacement of any defective part if the unit is returned transportation prepaid to SECO LARM This Warranty is void if damage is caused by or attributed to acts of God physical or electrical misuse or abuse neglect repair or alteration improper or abnormal usage or faulty installation or if for any other reason SECO LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship The sole obligation of SECO LARM and the purchaser s exclusive remedy shall be limited to replacement or repair only at SECO LARM s option In no event shall
Download Pdf Manuals
Related Search