Schlage P515-549 BE365 User's Manual
Contents
1. Reverse steps to assemble lock FE595 Features Bunton D OOO Keypad ODO Key Override Thumbturn Outside Knob Lever Inside Knob Lever amp Button Thumbturn Press to turn on backlight Switches between locked and unlocked Press to clear an incorrect code entry See below Keypad Outside Knob Lever Use to unlock the lock by entering a Always rotates Only retracts latch when valid four digit user code lock is unlocked Use to program the lock See page 8 F Inside Knob Lever C Key Override Always rotates and retracts latch for See page 10 immediate exit FE595 Lock Operation Thumbturn in Locked Position Thumbturn in Unlocked Position Locked User code required for entry Unlocked No user code required for FE595 Lock Operation Continued To Unlock the Lock While thumbturn is in locked position Enter a valid four digit user code See note The button will flash green Rotate outside knob lever within five seconds to open door After five seconds the lock will automatically relock NOTE The lock has two unique preset user codes that are printed on the front of this guide and back of keypad assembly FE595 Changing the Battery For low battery indications see page 11 NOTE Replace with premium 9V alkaline battery2. Reverse steps to assemble lock Programming for All Models Label is located on front of guide and back of keypad assembly Four Digit User Codes Six Digit Programming Code 4DUC Programming Code 123456 6DUC Activates lock User Code A 4321 S N 1 0000000q Programs lock Can be changed User Code B 5678 Model BE365 e Can be changed e Up to 19 user codes P e Won t operate lock e Won t program lock JE xample Schlage Button on front of lock Lights orange while in programming mode Flashes green when programming is successful Lights red when there is an error Retry steps or see troubleshooting guide on page 11 Press to exit programming mode at any time Wait until button stops flashing before entering additional codes Schlage Button 6DPC Six Digit Programming Code 1 Specific Number on Keypad 4DUC Four Digit User Code Add a new user code 6DPC 1 gt New 4DUC Reenter New 4DUC Delete one existing or preset user code 6DPC gt gt D Existing 4DUC Reenter Existing 4DUC Change current or preset programming code IMPORTANT If you forget your new programming code you will have to reset the lock 6DPC gt gt gt 3 New 6DPC Reenter New 6DPC Enable disable all user codes 1 Disable All User Codes DPC gt gt 4 2 Enable All User Codes DPC Turn beeper on or off preset is on NOTE Lock will still beep when battery is low 6DPC gt 96
3. Deadbolt Extended Unlocked Deadbolt Retracted Locked Unlocked Q User code No user code Deadbolt eS required required MSY P for entry for entry BE365 Changing the Battery For low battery indications see page 11 NOTE Replace with premium 9V alkaline battery Reverse steps to assemble lock FE575 Features ae ISSCHLAGE Button 6 OO l OOOO Key Override Outside Knob Lever Inside Knob Lever aay CLO l amp Button C Key Override Press to turn on backlight See page 10 Press to clear an incorrect code entry y D Outside Knob Lever Keypad Always rotates Only retracts latch when Use to unlock the lock by entering a lock is unlocked valid four digit user code E Inside Knob Lever t the lock Bae so pro amelie ee rade ay Always rotates and retracts latch for immediate exit E575 Lock Operation To Unlock the Lock Enter a valid four digit user code See note The button will flash green Rotate outside knob lever within five seconds to open door After five seconds the lock will automatically relock NOTE The lock has two unique preset user codes that are printed on the front page of this guide and back of the keypad assembly FE575 Changing the Battery For low battery indications see page 11 NOTE Replace with premium 9V alkaline battery
4. of manual or back of keypad E for preset 6DPC I TOGOTIMY ODED If needed restore lock to preset settings See page 9 Outside thumbturn does not freely spin after deadbolt is None None Lock is malfunctioning See page 12 thrown Number of beeps if beep is turned on Schlage Customer Service U S A and Canada 888 805 9837 P O Box 1210 Fax 800 366 5625 Olathe KS 66051 1210 www schlage com Emergency Lock Override If the outside thumbturn does not freely rotate or the lock is malfunctioning you can enable the emergency override feature When emergency override is engaged a key must be used to extend retract the deadbolt a Remove screws and thumbturn assembly b Disconnect and remove battery O c Use screwdriver to rotate slot on mounting plate to LOCKOUT position TOP A NOTE You may need to have your lock repaired or replaced M ERRID J
5. 5 For BE365 see page 7 2 Press and release 3 Reconnect the battery and wait until is no longer lit 4 Within 10 seconds press and hold gt until lights green and the lock beeps Keeping Your Lock Secure Security Tips 1 Do not share your programming code with other people Write down your programming and user codes and keep them in a safe place Use the table below if desired Give each person his her own user code You can have up to 19 user codes If you don t remember or don t know who has a user code you can delete all the user codes See page 8 Use key override to unlock the lock in the following situations 1 Battery is dead 2 No User Code is known FE575 and FE595 NOTE Key does not retract latch Rotate key Rotate key 270 When finished Insert Key 270 to unlock Rotate knob lever back to relock remove key Key cannot be removed in this position BE365 Only NOTE Key will both extend and retract deadbolt Push key into Rotate key and Insert key thumbturn thumbturn 90 CB AY op na ys WE Troubleshooting Guide Problem Beeps Lights _ Solution S Red 4DUC entered is not a valid 4DUC User code 4DUC does not unlock lock 1 High Green then User codes have been disabled Enable User 1 Low Red Codes See page 8 1 Too many incorrect user codes have been entered Wait 30 seconds and try again 2 If keypad does not respond
6. BE365 FE575 FE595 Programming Operating Guide P515 549 Table of Contents BE365 Features Lock Operation Changing the Battery FE575 Features Lock Operation Changing the Battery FE595 Features Lock Operation Changing the Battery Programming for All Models Keeping Your Lock Secure Key Override Troubleshooting Guide Emergency Lock Override Preset Programming Code User Code B 5678 Model BE365 Kehno Lock Series Preset User Codes Place Label Here BE365 Features ees Button DOOON B Keypad C Key Override D Outside Thumbturn E Inside Thumbturn C Key Override See page 10 Press to turn on backlight Press to clear an incorrect code entry D Outside Thumbturn Freely rotates until deadbolt is activated Keypad Then thumbturn will extend or retract Use to unlock the lock by entering a deadbolt valid four digit user code E Inside Thumbturn t the lock i HSS 1O pro rarik tio logi 1959 Page Extends and retracts the deadbolt from the inside E365 Lock Operation To Retract the Deadbolt To Extend the Deadbolt Enter a valid four digit user code a Push button The button will flash green b Rotate outside thumbturn while Rotate outside thumbturn within five button is lit to extend deadbolt seconds to retract deadbolt BE365 Lock Operation Continued Locked
7. Delete ALL user codes at once IMPORTANT This will delete all the user codes but not the programming code 6DPC 6 Reenter EDPC 8 Enable disable Turn Lock feature BE365 ONLY preset is enabled NOTE When Turn Lock feature is disabled you must enter a valid user code to extend the bolt 6DPC gt 9 7 Create a temporary code house sitter plumber etc Add New User Code 6DPC gt 1 New 4DUC Reenter New 4DUC Give person his her code but keep a written copy for yourself When code is no longer needed delete User Code 6DPC gt gt 2 Existing 4DUC Reenter 4DUC Delete a user code if user code is unknown IMPORTANT This will delete ALL the user codes but not the programming code 1 Delete ALL User Codes 6DPC gt amp gt 6 gt Reenter DPC Add New User Code 6DPC gt 1 gt New 4DUC Reenter New 4DUC Repeat step 2 until all User Codes are reentered Ensure only you have codes to the lock 1 Change Programming Code 6DPC gt amp 3 New 6DPC Reenter New 6DPC Delete ALL User Codes 6DPC gt gt 6 Reenter DPC Add New User Code 6DPC gt gt 1 New 4DUC Reenter New 4DUC Restore ALL preset lock settings IMPORTANT Lock will be reset to the preset programming and user codes All existing user codes and current programming code will be erased 1 Disconnect the battery For FE575 see page 3 For FE595 see page
8. after 30 seconds then replace battery For FE575 see page 3 For FE595 see page 5 For BE365 see page 7 Battery is low and should be replaced There is a delay before unlock High Low Red then For FE575 see page 3 after a valid 4DUC is entered then 1 Green For FE595 see page 5 For BE365 see page 7 Battery is dead and MUST be replaced blinking red but no codes Quick Red For FE575 see page 3 have been entered Blinking For FE595 see page 5 For BE365 see page 7 19 4DUCs already exist Delete a 4DUC gow O Red before adding a new one See page 8 Cannot add a new 4DUC 1 Second 4DUC entered did not match first 2 4DUC entered 2 The 4DUC matches the first four digits of the existing 6DPC Second 4DUC entered did not match first Cannot delete a 4DUC 2 Red ADUC entered does not light when numbers are pressed 1 Second 6DPC entered did not match first Cannot change 6 digit 2 6DPC entered programming code 6DPC 2 First four digits of new 6DPC match an existing 4DUC Cannot delete all user codes 2 Red 6DPC entered second time is incorrect Any key other than was pressed immediately after programming mode was entered 2 Anincorrect entry was made during the programming process Lock will not stay in programming mode For BE365 after pushing Schlage button and rotating thumbturn the deadbolt does not extend Turn Lock Feature is disabled See page 9 Check front
Download Pdf Manuals
Related Search