Samsung SW52ASP User's Manual
Contents
1. SOAK e The laundry is soaked in water so that heavy dirt can be eliminated sufficiently e You can choose soak cycle after choosing wash program When you select soak function 5 minute cycle 1 min washing then 4 min pause continue for 30 minutes before main wash program e Load size and water level is determined automatically gt Unplug the power cord after washing RINSE AND SPIN ONLY When you choose this cycle only rinse amp spin cycle are operated without wash cycle e Pressing cycle key during operation changes the number of rinse see above You cannot change the spin dry time using this function Unplug the power cord after washing SPIN ONLY When you choose this cycle only spin cycle is operated e Pressing cycle key during spinning only cycle changes the spin dry time The spin dry time can be changed to between 1 and 7 minutes Unplug the power cord after washing DELAY START e This function allows you to delay the start of your chosen wash program for 3 4 18 hours e By pressing the delay start key you can select delayed period for 3 4 17 18 hours and your washing machine will finish the selected wash program after the delayed period Washing machine won t work Is the water tap opened Is the washer plugged in Is the power cut off N Is the fuse all right E Is there enough water amp Water does not drain Is the drain hose down No pump2. Is the drain hose frozen Is the drain hose clogged If the water does not drain in 15 minutes a buzzer will sound and the remaining time indicator will show 5E While lid is opening the washing machine won t work Make sure to close the lid while washing machine is operating TROUBLESHOOTING Spinning does not work Is the laundry spread out evenly in the washer Is the washer set on a sturdy K flat surface Loe Is the lid closed E Water is not supplied Is the water tap opened Is the water cut off Is the water supply hose or hose connection clogged Is the water tap frozen If water is not supplied in 60 minutes a buzzer will sound and the remaining time indicator will shown 4E TTT SPECIFICATION SW52ASP SW62ASP Power input Watts 426 Load capacity kg 6 0 Size WxDxH mm 540 X 560 X 850 588 X 618 X 955 Net Weight kg 38 Water Consumption liters 106 high 138 high Water Pressure min max 50 780KPa 50 780KPa Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center Samsung Electronics Australia 7 Parkview Drive Homebush Bay NSW 2127 1300 362 603 www samsung com au
3. Owner s Instructions SW52ASP SW62ASP Please read this manual before using and note how to use in the proper manner Please be careful of keeping the manual Otherwise it should be bought separately The User s Manual is for common use Make use of the User s Manual depending upon your washing machine model FEATURES io 5 soci aware ces 6 elie a aces sca verwels Ye 8 ar 1 DESCRIPTION OF PARTS 2 eee cece ee cccns 2 SAFETY INSTRUCTIONS 0 ce eee cee vvcce 3 INSTALLATION amp MAINTENANCE 00 00 4 ENVIRONMENT 2 cece cece cece nee e een ncees 4 IN CASE OF PUMP DRAINED WASHER 2ee eee 4 HOW TO CONNECT WATER SUPPLY HOSE 2000 4 CLEANING THE FILTER NET 2 cece cere ee ec ences 5 HOW TO ADD THE FABRIC SOFTENER 22 2 ee eee 5 HOW TO PUT THE DETERGENTIN 0000 ce eeenseves 5 CLEANING THE FILTER 1 ee eee eee e eee r erences 5 LEVELLING vion eaa oi sha oe She AE to ev cto oe ete 5 PRECAUTIONS is 66 80 68 e0diinn se amacaa aa a ear a a 6 WASHING INSTRUCTION eessesssosussseeseeo 7 PROCEDURE sce oi e rici e a ae 6 eter EA E EEEE O 7 WASH PROGRAM sessssssssossessssesessesene 7 WASHING PROGRAM sssssssesososeseseseeo 8 CLEANING THETUB sa hetene ee ee eee eee een eee eeee 8 OPTIONAL CYCLE EEEE TAE EEEE 9 TROUBLESHOOTING eee e eee e eee vnne 10 SPECIFICATION E EREE EEEE E Ses 10 Register your product at www samsung com global r
4. authorized person in order to avoid the risk Connect the grounding wire to the shell plate and bury it under at least 25cm of earth elternatively connect the ground wire to the appropriate pin ona properly grounded power receptacle Never connect the wire to a telephone line lightning rod or gas pipe pp on ummm NSTALLATION amp MAINTENANCE ENVIRONMENT Leave some space Maintain at least 10cm between the washer and the wall Place the washer on a sturdy flat surface If the washer is placed on an uneven or weak surface noise or vibration occurs allowable slope is 1 degree Never install the washer in a very steamy environment or where it might be open to the rain Excessive moisture may cause an electrical shock hazard Avoid direct sunlight or heaters As plastic and electrical components are affected by direct heat never place the washer near furnaces boilers etc Do not place under direct sunlight HOW TO CONNECT WATER SUPPLY HOSE IN CASE OF PUMP DRAINED WASHER e Install the drain hose in the position of about 70 80cm above the ground e Take out the cap hose and connect the outlet hose e Be sure to join tightly the drain hose into the drain outlet on the left side of the machine 70 80cm OUTLET HOSE Check the type of tap fitting which is in your laundry and then see appropriate instruction below A tap of ordinary type is desirable ORDINARY TAP SQUARE TAP 1
5. does of Do not open the lid during the Spin Dry cycle fabric softener is stored in the softener inlet it is If added too early its effectiveness will decrease automatically put in at the last rinsing cycle Do not leave the softener Do not use detergent bleach or starch into the into the Softener Softener Inlet Dispenser for a long time e Using too much softener may produce Because softner f unsatisfactory results became stiff BROW TO PUT THE DETERGENT IN 1 Open the detergent box by pulling in the direction of the arrow as shown in the figure and then put the powder detergent in the detergent box 2 Put in one time amount of detergent evenly so the detergent may not brim over the box Detergent Device Put the detergent in proportion to water level Caution If softener is stored over the above base line it may flow down at any time DPEVELLING LEANING THE FILTER pump drained washer 1 Place a rag under washer filter not to wet the floor If the washer is not leveled with the ground it makes the 2 Turn the filter cap to the left machine tremble more or be out of order So make sure 3 Take out the filter and remove any sludge that the washer is leveled properly 4 Reassemble in reverse order SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING THE POSITION OF THE WASHING TUB e Open the lid of the machine pour water into the tub up to the level just below the pulsator and adjust the legs so that t
6. materials under the washer You may be hurt by spinning board beneath the washer Stay away from the washer when the bottom of the washer sinks into the water There might be an electric shock Please wait until the water drains out completely Do not put laundry stained with gasoline benzene or alcohol in the washer and keep the materials away from the washer An explosion or a fire may take place During spinning don t put your hand in the spinning tub It may hurt your hands If it does not stop within 15 seconds after you open the lid call service agent immediately e This appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use the appliance safely Young children should be supervised to ensure that they do not play with the appliance e This appliance has to be connected to the plug endurable to proper power consumption e This appliance has to be positioned so that the plug is accessible after installation No user serviceable parts inside Refer any servicing to qualified service personnel Otherwise this may cause a mechanical error electric shock fire or physical damage The product warranty does not cover problems resulting from disassembling the product Do not use this product for business purposes e For washing machines with ventilation openings in the base that a carpet
7. must not obstruct the openings CAUTIONS There might be a slight injury or damage when you violate this instruction Don t install it in the area with moisture or outdoor where it has rain or snow An electric shock or a fire may take place Please unplug the power supply cord when you do not use it An electric shock or a fire may take place If there is dust or water on the power supply plug and its connected part please remove it completely An electric shock or a fire may take place Do not make your kids look into the inside of the washer If your kid falls into the washer his life could be in danger e Ventilate immediately without touching the power plug if gas is leaking An electric shock or a fire may take place if it catches flame If the washer makes strange noise smell or smoke unplug it promptly and call service agent An electric shock or a fire may take place e When cleaning don t spray water to the parts of the washer directly It may make it s life span shorten Also an electric shock or fire may take place Don t use several appliances together with an outlet A fire may take place due to unusual heat Don t press the button with an awl or pin An electric shock or a fire may take place Use the new hose sets and old hose sets should not be reused If the damage is found on the current cord in use it should be replaced by manufacturer service cener or
8. Remove the adaptor from the water supply hose ROTATING TAP In case of square tap e Take out the internal part of the connector and join it in the following way en Internal part 4 Connect the water supply hose to the adaptor Pull down the part c of the water supply hose When you release part c the hose is automatically connects to the adaptor making a click sound 2 First using a type screw driver loosen the four screws on the adaptor Next take the adaptor and turn part b following the arrow for gap about 5mm between them 3 Connect adaptor to the water tap by tightening the screws firmly Then turn part b following the arrow and put a and b together 5 Connect the other end of the water supply hose to the inlet water valve at the top of the washer Screw the hose clockwise all the way in 6 lf the water tap is a screw type assemble a water supply hose that fits to the tap as shown Note The appliance is to be connected to the water mains using new hose sets and that old hose sets should not be used CEEANING THE FILTER NET 1 Push the upper part of 2 Open the cover as 3 Clean the filter 4 Close the cover and insert the lower the filter and pull in shown in the figure part of the filter in the basket first and then push the filter with click sound HOWTO ADD THE FABRIC SOFTENER e When a proper amount one time
9. egister CODE NO DC68 01488K EN MAGIC FILTER 4 ECONO WASH COURSE e This unique magic Filter ensures that e Designed to address concerns on water all the lint inside the tub is captured for consumption Less water is used per top quality filtering results to deliver wash while continuing to deliver a clean consistently effective cleaning results and effective washing performance It has been certified from WELS Water Efficiency Labelling and Standards of Australia SOFTENER DISPENSER e The Softener Dispenser releases the fabric softener at the appropriate time when the last rinsing proceeds 2 WATERFALL FLOW e The Waterfall Flow injected from under the pulsator cascades with full force back into the tub pushing down any clothes that float right under the water surface It is this Waterfall Flow that enables this washing machine to effectively wash large and heavy items such as bluejeans and blankets mm DESCRIPTION OF PARTS WATER SUPPLY HOSE HOT WATER SUPPLY HOSE COLD FILTER LID Be sure to keep the lid closed during washin and spinning hen p DRAIN HOSE PUMP Lint will be collected in the filter during washing FABRIC SOFTENER S p DISPENSER ARIE GF DETERGENT BOX BLEACH INLET ss S POWER CORD WATERFALL FLOW 4 SPIN BASKET 7 H PULSATOR option tea GROUND LEAD FRONT CONTROL When the water pipe is PANEL H metal
10. ergent See Page 5 Add the fabric softener See Page 5 Close the lid Press power button Choose the wash program amp optional cycle See Page 7 9 If you choose SENSOR program you don t need to select water level Water level is set automatically at SENSOR program Press the START PAUSE button Select the water level Before choosing the water level remember following things When you choose SENSOR HEAVY DUTY ECONO WASH WOOL program water level is selected AUTO automatically but if you want to choose water level manually you can select HIGH MEDIUM LOW MINIMUM Select the water temperature Before choosing thr water temperature remember the following You can choose COLD gt COLD HOT gt HOT on all programs HOT is hot wash and cold rinse COLD is cold wash and cold rinse 10 Close the lid and press the START PAUSE button 11 Do you want extra rinse For extra rinses press the cycle key 1 to 5 times depending on the number of extra rinses required You can select up to 5 extra rinses or return to a single rinse by pressing the cycle key The time left display will show the number of rinses selected Note that the extra rinse program is not available when pause is selected or during the spin cycle WASH PROGRAM SENSOR HEAVY DUTY ECONO WASH WOOL SW52ASP 25 min 26 min 18 min 5 min Wash Time SW62ASP 20 min 20 min 18 min 5 min Wash Action Normal Normal N
11. he pulsator is positioned at the center of the water as shown in the figure e Place the machine more than 10cm away from the wall e Adjust the legs on feet for levelling Loosen EY Lock ANY PRECAUTIONS WARNING NOTE THE FOLLOWING PRECAUTIONS TO PREVENT ELECTRICITY f on LEAKAGE AND THE POSSIBILITY OF ELECTRIC SHOCK Earthing is necessary to prevent leakage or electric shocks caused by the electric currents leaked from the machine How to earth an outlet with earthing terminals when an earthed power load is not fitted Outlet with earthing terminals Earthing e Even when the internal wires of the earthing terminals are terminas Ny joined connect the earthing conductor green of the B machine to the tap When using an extension cord and a boosting transformer Make sure that the earthing conductor is connected SS Never make an earthing to e The telephone line lightning rod or gas pipe as it is extremely dangerous in case of lightning strikes Gas pipe _ Earthing conductor Earthing conductor WASHING INSTRUCTION PROCEDURE 1 N Sort the laundry into separate wash loads Each load of washing should contain clothing which needs the same washing conditions For example you should not wash delicate clothes with very dirty work clothes Load the laundry into washing Before load check all pockets and close zippers hooks and eyes Add the det
12. make sure to cover H the end of the ground wire ADJUSTABLE LEGS 777775757222427 Adjust the length H Sption of the legs when y H cons installing the washer aes cae ce ae ae RAT PROTECTION PANEL 7 Start Pause Time sh O Cold O High O Soak O Sensor Power H O Hot OMedium Wash O Heavy Duty Min O Low O Rinse O Econo Wash OMinimum Spin O Wool Delay Start th Temperature p Water Level Cycle ioe CONTROL PANEL SAFETY INSTRUCTIONS Please note that the following precautions for safety intend to prevent unpredictable danger and damage by helping the proper use in safety When using hot water in washing please make sure that the water should not exceed 50 C Plastic parts may be deformed or damaged and an electric shock or a fire may take place WARNING There might be serious injury or fatal accident when you violate this instruction If the plug power supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard Do not pull the cord off or touch it with moist hands An electric shock or a fire may take place Do not bend the power supply cord by force or press it with heavy things An electric shock or a fire may take place Do not install the washer nearby electric implement or don t put a candle light or cigarette light on the washer A fire may take place During operation do not put your hands or metal
13. ormal Gentle HOT HOT HOT Wash Temp HOT COLD HOT COLD HOT COLD an COLD COLD COLD 4 HOT COLD Deep Rinse COLD COLD COLD COLD SW52ASP 5 min 30sec 5 min 30sec 5 min 30sec 1 min 30sec Spin Time SW62ASP 5 min 5 min 5 min 1 min Total Time SW52ASP 48 min 49 min 43 min 23 min High Water level SW62ASP 49 min 49 min 49 min 29 min ss ASHING PROGRAM SENSOR Program e The best washing program is chosen automatically e Load size and water level is determined automatically Unplug the power cord after washing HEAVY DUTY Program e This program is suitable for heavily soiled laundry e Load size and water level is determined automatically or you can choose the water level you want gt Unplug the power cord after washing CLEANING THE TUB e Press the POWER button e Press the PROGRAM button to select the HEAVY DUTY course e Press the CYCLE button to select SOAK You can select the water supply or temperature hot cold e Press the WATER LEVEL button to select HIGH e Press the START HOLD button Add a dedicated detergent and close the lid NOTE Never place laundry in the tub when cleaning inside the tub as this can cause discoloration or damage to the laundry When doing the laundry after cleaning the tub you may find some impurities These are just detergent residues and impurities after the tub cleaning Perform the rinse cycle two to three times ECONO Wash Program e Saving yo
14. ur time energy and water e Achieving Rinse performance which is determined at AS NZS 2040 e This program is suitable for lightly soiled laundry e Load size and water level is determined automatically or you can choose the water level you want Unplug the power cord after washing WOOL Program e This program is suitable for woollen clothes Only high and medium water levels are available gt Unplug the power cord after washing X Keeping the tub clean When using the machine under humid conditions for an extended time various bacteria from the air may stick to the tub and form black dirt fungi causing damage to the human body To keep the tub clean and hygienic at all times it is recommended reading Cleaning the Tub above and using only dedicated or recommended detergents to clean the tub regularly at least once every one to three months OPTIONAL CYCLE mmm WASH ONLY When you choose this cycle wash cycle is operated Pressing optional cycle key during washing changes the wash time in two minute intervals e The wash time can be changed to between 3 and 25 minutes Load size and water level is determined automatically Unplug the power cord after washing RINSE ONLY When you choose this function only rinse cycle is operated e Pressing function key during rinsing changes the number of rinses Up to 5 rinses can be optionally selected Unplug the power cord after washing
Download Pdf Manuals
Related Search