Samsung SCX-RD100 User's Manual
Contents
1. COAXIAL REMOTE CONTROLLER user manual Tye imagine the possibilities Thank you for purchasing this Samsung product To receive more complete service please register your product at www samsungsecurity com ela Safety information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING WARNING 1 a This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture Be sure to use only the standard adapter that is specified in the specification sheet Using any other adapter could cause fire electrical shock or damage to the product Incorrectly connecting the power supply or replacing battery may cause explosion fire electric shock or damage to the product Do not connect multiple controllers to a single adapter Exceeding the capacity may cause abnormal heat generation or fire Securely plug the power cord into the power receptacle Insecure connection may cause fire When installing t2. Monitor 5 T 1 Connect the product to DC 12V power source or insert 4 AA sized batteries into the battery compartment 2 Set the protocol switch 7 to ON 3 Connect the VIDEO IN of the unit and VIDEO OUT of the Al Camera directly For proper data communication the unit and Al camera should be connected directly lf you connect a DVR or keyboard in the middle of the main unit and Al camera bidirectional communication will not be established 4 Connect VIDEO OUT of the main unit to a monitor s video input terminal 5 Connect TX of RS 485 device to RX of the main unit For a full duplex system connect RX of RS 485 device to TX of main unit additionally 6 Using RS 485 device you can control the camera menu For proper coaxial communication Al camera should be set to Samsung protocol Refer to the switch settings See page 17 XE By factory default protocols of SAMSUNG and PANASONIC are supported Or a For additional protocols update the following software program via the web Input of video signal is required to control RS 485 English 13 Connection amp Control TO CONTROL THE CAMERA USING RS 232 DEVICE VIA COAXIAL COMMUNICATIONS Monitor 2 1 Connect the product to DC 12V power source or insert 4 AA sized batteries into the battery compartment N Set the p
3. amp Control SWITCH SETTING TABLE a Use a combination of pin 1 2 3 4 of the Protocol setting switch to select a protocol pepe HALF half duplex PROTOCOL FULL full duplex Protocol Setting Switch OH 1 it Boel HALF FULL Pin1 Pin 2 Pin3 Pin 4 0 0 0 0 SAMSUNG HALF 1 0 0 0 SAMSUNG FULL 1 1 0 0 PANASONIC HALF 0 0 1 0 PANASONIC FULL 1 1 1 0 PHILIPS HALF 1 0 0 1 KALATEL HALF 0 1 0 1 ERNA HALF 1 1 0 1 DIAMOND HALF 0 0 1 1 VCLTP HALF By default it is configured to support SAMSUNG and PANASONIC NOTE For other protocols you can find assistance from our website at http www samsungsecurity com Use pin 7 and 8 of the Protocol setting switch to set the coaxial output PIN 7 Output Selection eH ON COAXIAL out IT OFF RS 485 out PIN 8 RS 232 input q ON RS 232 input PROTOCOL OFF RS 232 No use N m RS 232 and RS 485 communications cannot be used for simultaneous input NOTE English 17 Connection amp Control See the following table to set the baud rate Oe PROTOCOL 1 SAMSUNG BAUD RATE PIN 5 PIN 6 38400 BPS OFF OFF 19200 BPS ON OFF 9600 BPS OFF ON 4800 BPS ON ON 2 PHILIPS BAUD RATE PINS PIN6 38400 BPS OFF OFF 9600 BPS ON OFF 3 PANASONIC BAUD RATE PIN 5 PIN 6 19200 BPS OFF OFF 9600 BPS ON OFF 4800 BPS OFF ON 4 DIAMOND VC
4. INSTALLATION ENVIRONMENT e Please check the following instructions before installation for your safety e The way of connecting the main product with external devices COAXIAL BNC is very important to build up a proper system Do not disassemble the unit doing so could expose you to dangerous high voltage points INSTALLATION PRECAUTIONS e Make sure you turn off the product before installation e Do not put a strong force on or shake the product otherwise it may cause malfunction e Keep the product away from areas of strong magnetic field or electric interference or wireless devices such as radio or TV set e Keep clean the installation place during and after the installation e An abnormal smells from the product is a sign of abnormal condition which may cause fire or electric shock In this case disconnect the product from the main power immediately and contact the retailer for technical help from authorized servicing e Keep the product away from a wet floor do not use an unearthed power extension cable worn out power cord neither forget earth grounding e Use a dry cloth only to dirt off the product If the product is badly dirty apply neutral detergent on a cloth that is used to dirt off and wipe it out with a dry cloth e Do not use volatile substances such as alcohol benzene or thinner as these may damage the finish English 11 Connection amp Control TO CONTROL THE CAMERA COAXIAL COMMUN
5. be sure to tum off the power and then move or reinstall it Remove the power plug from the outlet when there is a lighting storm Neglecting o do so may cause fire or damage to the product Keep out of direct sunlight and heat radiation sources It may cause fire install it in a place with good ventilation Avoid aiming the controller directly towards extremely bright objects such as sun Apparatus shall not be exposed to dripping or splashing and no objects filled with iquids such as vases shall be placed on the apparatus The Mains plug is used as a disconnect device and shall stay readily operable at any time English 3 Important Safety Instructions 1 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water oa fF oO ND Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replaceme
6. using the menus You can use the menu as following Press and hold ENTER Moves to the main menu screen To exit the menu screen press and hold the key again Press ENTER briefly Used to confirm the current settings Four Direction Keys Used to move the cursor up down or left right Control of pan tilt zoom using the buttons is not supported N Input of video signal is required to control RS 485 NOTE a The next time you access the menu press and hold the ENTER key twice English 15 Connection amp Control TO CONTROL THE CAMERA USING RS 485 SIGNAL OUTPUT VIA RS 232 COMMUNICATIONS Monitor 1 Connect the product to DC 12V power source or insert 4 AA sized batteries into the battery compartment 2 Set the protocol switch 8 to ON 3 Connect the RX of the unit to the RS 485 port of the camera 4 Match the camera s address baud rate and protocol to the same to those of the unit RS 232 can be controlled using the Samsung protocol alone 5 Connect the RS 232 device s cable to the RS 232 port of the main unit 6 Using RS 232 device you can control the camera menu N m RS 232 and RS 485 communications cannot be used for simultaneous input NOTE w For the switch settings see the switch setting table See page 17 Input of video signal is required to control RS 485 16 COAXIAL REMOTE CONTROLLER ltr Connection
7. ICATIONS Monitor mN 1 Connect the product to DC 12V power source or insert 4 AA sized batteries into the battery compartment 2 Set the protocol switch 7 to ON 3 Connect the VIDEO IN of the unit and VIDEO OUT of the Al Camera directly For proper data communication the unit and Al camera should be connected directly f you connect a DVR or keyboard in the middle of the main unit and Al camera bidirectional communication will not be established 4 Connect VIDEO OUT of the main unit to a monitor s video input terminal 5 Turn the Power switch ON When it is powered on for the first time initialization begins and the status LED blinks once completed During the initialization no operation is enabled 6 Now you can control the camera by using the menus You can use the menu as following Press and hold ENTER Moves to the main menu screen Press ENTER briefly Used to confirm the current settings Four Direction Keys Used to move the cursor up down or left right For proper coaxial communication Al camera should be set to Samsung protocol Refer to the switch settings See page 17 Control of pan tilt zoom using the keys is not supported 12 COAXIAL REMOTE CONTROLLER Connection amp Control TO CONTROL THE CAMERA USING RS 485 DEVICE VIA COAXIAL COMMUNICATIONS
8. L TP BAUD RATE PINS PIN 6 9600 BPS OFF ON Only supports 9600 bps 18 COAXIAL REMOTE CONTROLLER Connection amp Control 5 ERNA BAUD RATE PINS PIN 6 2400 BPS ON ON Only supports 2400 bps 6 KALATEL BAUD RATE PIN 5 PIN 6 9600 BPS OFF ON 4800 BPS ON ON English 19 Specifications SPECIFICATIONS Item Description Communication Method COAXIAL INTERFACE COAXIAL Range Max 500m with 5C HFBT cable Connector Type D SUB 9P RS 232 Port 1 Port 4800 9600 19200 38400bps BAUD RATE Only Samsung protocol supported Connector Type 4P Terminal Type Ae 486 Port 1 Port BAUD RATE 2400 4800 9600 19200 38400bps Supports each protocol USB PORT USB2 0 S W PROGRAM UPLOAD Composite Video 1 0Vp p 750hm VIDEO IN OUT Cable Compensation out Select S L Environmental Operating Temp 10 C 50 C Conditions Humidity Less than 90 POWER DC12V 10 DIMENSIONS WxHxD 150 W X 36 H X 102 0 WEIGHT NET 200 g 20 COAXIAL REMOTE CONTROLLER Spectications DIMENSIONS Unit mm Ts o M 101 5 REMOTE CONTROLLER SCX RD100 W Z English 21 Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European U
9. avigation Key Use this to navigate through the menus 8 COAXIAL REMOTE CONTROLLER Introduction PART NAMES AND FUNCTIONS Rear Panel AA BATTERY You can use 4 AA sized batteries for the power The average operation time is 20 hours based on the alkaline battery If the battery is discharged it can cause a distortion of the video signal or electric interference iS Remove the battery if you do not use the controller for a longer period Otherwise it NOTE may cause damage to the controller from a leak of the battery solution Take caution not to change the specified polarity Do not use a new battery with an old one For storing used batteries keep out of reach of children Wasted batteries are to be collected separately English 9 Introduction Top USB Port This terminal is used for updating the product s firmware RS 232 Port 9 pin D SUB Used to control remotely using RS 232 communication RS 485 Port 4 pin Used to control remotely using RS 485 communication VIDEO IN OUT Connector BNC VIDEO IN receives coaxial communication from cameras and VIDEO OUT outputs the video signal DC12V Power Connector 2 PIN Used for connecting DC12V power source 10 COAXIAL REMOTE CONTROLLER Instalaton CHECKING
10. he controller fasten it securely and firmly The fall of controller may cause personal injury Do not place conductive objects e g screwdrivers coins metal parts etc or containers filled with water on top of the controller Doing so may cause personal injury due to fire electric shock or falling objects Do not install the unit in humid dusty or sooty locations Doing so may cause fire or electric shock If any unusual smells or smoke come from the unit stop using the product In such case immediately disconnect the power source and contact the service center Continued use in such a condition may cause fire or electric shock COAXIAL REMOTE CONTROLLER 9 Safety information If this product fails to operate normally contact the nearest service center Never disassemble or modify this product in any way SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair 10 When cleaning do not spray water directly onto parts of the product Doing so may cause fire or electric shock CAUTION 1 on oO a Do not drop objects on the product or apply strong blows to it Keep away from a location subject to excessive vibration or magnetic interference Do not install in a location subject to high temperature over 50 C low lemperature below 10 C or high humidity Doing so may cause fire or electric shock f you want to relocate the already installed product
11. ing Table 17 Specifications Specifications 20 Dimensions _______ 21 English 5 latroduction INTRODUCTION This product is a remote controller for Samsung s CCTV cameras of New generation DSP via coaxial cable not requiring additional control wirings Features e Long distance remote control Through RS 485 communication remote control is possible up to 1 2 kilometers e Easy Control Easy and simple 5 way keys for controlling the camera e System s Expandability It is possible to implement an integrated system by using the system controller SSC 5000 or similar through RS 485 communication e Portability Its small size and light weight maximizes the portability as well as its power source adopting standard battery for outdoor use List of controllable models e You can control Samsung s cameras supporting coaxial communications e Samsung s RS 485 supporting cameras can be controlled through RS 485 communication For supported 3rd party protocols refer to page 17 What s Included lt Controller gt lt User Guide gt 6 COAXIAL REMOTE CONTROLLER Introduction PART NAMES AND FUNCTIONS Front Panel v Jt JCI0 000 TERMINATION PROTOCOL 2 ag SAMSUNG e Qpowr sus L OD e 4 CABLE N a E a COMPENSATION N o o0 L 6 REMOTE CONTROLLER SCX RD100 o STATUS LED Displays the status of the current
12. nion and other European countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Correct disposal of batteries in this product Applicable in the European Union and other European countries with separate battery return systems This marking on the battery manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life Where marked the chemical symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 If batteries are not
13. nt of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus 13 Unplug this apparatus when a card is used Use caution A when moving the cart apparatus combination to avoid injury from tip over 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as powersupply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 4 COAXIAL REMOTE CONTROLLER Contents Introduction Introduction 6 Part names and functions ____________7 Installation Checking Installation Environment 11 Installation precautions 11 Connection amp Control To Control the camera coaxial communications ______ 12 To control the camera using RS 485 device via coaxial communications ______ 13 To control the camera using RS 232 device via coaxial communications 14 To control the camera using RS 485 signal output 15 To control the camera using RS 485 signal output via RS 232 communications _________ 16 Switch Sett
14. operation POWER LED When the controller turns on it will be turn light POWER Switch If you slide it to ON the controller turns on CABLE COMPENSATION Switch For long distance coaxial communications you can use this switch for amplifying the control signal Cable SPEC Compensation S L 5C HFBT 250M or less 200M 500M English 7 Introduction RS 485 TERMINATION amp PROTOCOL Setting Switch You can select to set the RS 485 termination Tum this switch ON if RS 485 termination is required Ei TERMINATION For multi protocol settings you can set the protocol and baud rate and selection of COAXIAL RS 485 or RS 232 aaa PROTOCOL Use pin 1 2 3 4 of the Protocol setting switch to select a protocol Use pin 5 6 of the Protocol setting switch to select a baud rate Use pin 7 of the Protocol setting switch to select COAXIAL RS 485 output Use pin 8 of the Protocol setting switch to select RS 232 input Address Switch For RS 232 RS 485 communications you can use this switch to set the address ADDRESS x 100 x 10 x 1 Set the address by using three switches shown above From the left the number is hundreds tens and ones place respectively The effective range of valid address is between 0 and 255 1 255 for multi protocol QE If you specify the address as other than between 0 and 255 it will be set to 0 NOTE Menu N
15. properly disposed of these substances can cause harm to human health or the environment To protect natural resources and to promote material reuse please separate batteries from other types of waste and recycle them through your local free battery return system
16. rotocol switches 7 and 8 to ON Connect the VIDEO IN of the unit and VIDEO OUT of the Al Camera directly w For proper data communication the unit and Al camera should be connected directly If you connect a DVR or keyboard in the middle of the main unit and Al camera bidirectional communication will not be established 4 Connect VIDEO OUT of the main unit to a monitor s video input terminal Connect the RS 232 device s cable to the RS 232 port of the main unit ao a Using RS 232 device you can control the camera menu The RS 232 device is the same as RS 485 regarding the protocol setting but supports only the Samsung protocol For proper coaxial communication Al camera should be set to Samsung protocol Refer to the switch settings See page 17 iS m RS 232 and RS 485 communications cannot be used for simultaneous input NOTE 14 COAXIAL REMOTE CONTROLLER xX Connection amp Control TO CONTROL THE CAMERA USING RS 485 SIGNAL OUTPUT onnswvs Gane Ava LAA Daa 1 Connect the product to DC 12V power source or insert 4 AA sized batteries into the battery compartment 2 Set the protocol switches 7 and 8 to OFF 3 Connect the RX of the unit to the RS 485 port of the camera 4 Match the camera s address baud rate and protocol to the same to those of the unit 5 Now you can control the camera by
Download Pdf Manuals
Related Search