Samsung HL-P5067W User's Manual
Contents
1. 46 screen At least 5 6 feet 50 screen At least 5 9 feet 56 screen At least 6 6 feet 61 screen At least 7 2 feet lt Side view gt Pa Saa At least 5 6 feet 46 screen 50 screen At least 5 9 feet 56 screen At least 6 6 feet 61 screen At least 7 2 feet Replacing the Lamp Why do need to replace the lamp The lamp used in a DLP TV has a limited lifespan For the best screen quality it needs to be replaced periodically After replacing the lamp the screen quality will be bright and clear as new When do need to replace it It should be replaced when the screen becomes darker less clear or when all three LEDs on the front Timer Lamp amp Temp are flashing Check before lamp replacement 1 The lamp must be the same code number and type 2 The lamp type is indicated on the right side of the TV It is also indicated on the lamp case 3 After checking the code number for the lamp give the code number to the store where you purchased the TV or to a Samsung Service center Caution 1 Replace with the correct code numbered lamp to avoid damage to the TV 2 Turn the power off and wait for 30 minutes before replacing the lamp as it will be hot 3 Do not touch the glass part of the lamp with your bare hands nor insert any foreign object inside the cover as it may cause poor screen quality electric shock or fire 4 Do not place2. AIR Channel 44 Viewing an External Signal Source Use the remote control to switch between viewing signals from connected equipment such as a VCR DVD Set Top box or the TV source broadcast or cable Setting the Signal Source Press the MENU button Press the ENTER button to select Input G Source List S AAA Edit Name Anynet O Sound q Channel Sa Setup kg Guide Move Enter U Return Alternate method Press the SOURCE button on the remote control repeatedly to select an external signal source Viewing Position Press the ENTER button to select Source List Press the A or W button to select a signal source then press the ENTER button TV Picture AV2 Sry AV3 Terie SVideo1 sE S Video2 eT v More Guide Move Enter T Return e When you connect equipment to the TV you can choose between the following sets of jacks AV1 AV2 S Video1 S Video2 Component Component2 or HDMI DVI on the TV s rear panel and AV3 or S Video3 on the TV s side panel e HDMI input can be selected only when the external device is turned on and connected to the TV AVI To optimize your viewing comfort please follow the guidelines below for viewing distance If viewing for an extended period of time sit as far back from the screen as possible 1 lt Top view gt
3. Before your television can begin memorizing the available channels you must specify the type of signal source that is connected to the TV i e an antenna or cable system Press the MENU button Press the A or W button to select an item The main menu is displayed you want in the menu There are six menu groups Input Press the lt gt or ENTER button to dis Picture Sound Channel Setup play change or use the selected items and Guide Use the ENTER button to enter items in the menu Meany Source List Mode Standard S 7 Edit Name Color Tone Warm1 Picture Sound Anynet Size Digital NR channel DNIe gt My Color Control Vv More Move Enter 1 Exit Move Enter M Return 3 Press the EXIt button to exit Viewing the Display Press the INFO button on the remote control The TV displays the current channel the sta pee tus of certain picture and sound settings and the current time Ricture Mode Standard The information displayed varies according to Me Stereo the selected source V Chip es cormect Memorizing the Channels Your TV can memorize and store all of the available channels for both off air antenna and cable channels After the available channels are memorized use the CH and CH buttons to scan through the channels This eliminates the need to change channels by entering the channel digits There are three steps for me
4. AA n TV Rear of right side the Camcorder The audio video gt cables shown here are usually e H i i included with a Camcorder If not check your local electronics store If your Camcorder is stereo you need to connect a set of two cables Connecting a DVD Player The rear panel jacks on your TV make it easy to connect a DVD player to your TV Connecting to Y Ps PR Connect a set of audio cables between the COMPONENT 1 or 2 audio L R in jacks on the TV and the AUDIO OUT jacks on the DVD player TV Rear Panel Incoming Cable or fO a Antenna Oka ble N ble 3 ar w To enable Component video viewing 2 connect a set of video cables between the COMPONENT 1 or 2 VIDEO Y Ps Pr in jacks on the TV and VIDEO Y Ps Pr or Y Cs Cr OUT jacks on the DVD player Note For an explanation of Component video see your DVD player s owner s manual DVD Player Connecting to Audio and Video Jacks Connect a set of audio cables between the Audio in 1 or 2 jacks on the TV and the AUDIO OUT jacks on the DVD player TV Rear Panel Incoming Cable TT pS Le Connect a video cable between the Antenna i ez VIDEO IN 1 or 2 jack on the TV and A the VIDEO OUT jack on the DVD oi player DVD Player Connecting a DTV Set Top Box Connecting to Y Ps PR Connect a set of audio cables between the COMPONENT 1 or 2 audio L
5. You must obtain a CableCARD from a local cable service provider Insert the CableCARD into the CableCARD slot and the message TV Rear Panel CableCARD Inserted is displayed on the screen If the channel information does not already exist the message Acom Updating Channel List is displayed Cable or O during channel information configura Antenna tion The pairing information containing a telephone number CableCARD ID Host ID and other information will be displayed in about 2 3 minutes If an error message is displayed please contact your Service Provider When channel information configu ration is finished the message i ed Updating Completed is displayed Please insert the It indicates that the channel list is card asso now updated Connecting a Camcorder The side panel jacks on your TV make it easy to connect a Camcorder to your TV You can use your camcorder to view tapes without using a VCR Locate the A V output jacks on the camcorder They are usually found on the side or back of the camcorder Connect a set of audio cables LS N ee 2 between the AUDIO IN jacks on the l TV and the AUDIO OUT jacks on the camcorder If you have a mono Camcorder connect L mono to the Camcorder audio out using only one audio cable G te Dm h Connect a video cable between the or Camcorder 3 VIDEO IN or S VIDEO IN jack on ae the TV and the VIDEO OUT jack on ex
6. R in jacks on the TV and the AUDIO OUT jacks on the Set Top Box TV Rear Panel Connect a set of video cables 2 between the COMPONENT 1 or 2 VIDEO Y Ps Pr in jacks on the TV and VIDEO Y Ps Pr or Y Cs Cr OUT jacks on the Set Top Box Note For an explanation of Component video see your Set Top Box owner s manual wengu Incoming Cable or n9 Antenna voro biciraL SELECT AUDIO OUTPUT wie 5 oj I7 S auno VIDEO OUTPUT DTV Set Top Box Connecting to DVI Digital Visual Interface Connect a set of audio cables between the DVI audio L R in jacks on the TV and the AUDIO OUT jacks on the Set Top Box TV Rear Panel Connect an HDMI DVI video cable between the HDMI DVI IN jack on the TV and the DVI OUT jack on the Set Top Box Ky e Requires a Cable Converter Incoming Cable or Antenna Connect an HDMI cable between the HDMI DVI IN jack on the TV and the HDMI OUT jack on the Set Top Box Ky e Make sure the HDMI DVI source s power is on or you will be unable to select it in the DTV SetTop Box menu s source list weiner Incoming p mema Be So 1080 480 F 3 OPTICAL Connecting a Digital Audio System There are many types of digital audio systems on the market today A simplified illustration of an audio system is shown below For more information see your audio system owner s manual If your audio system has a optical dig ital aud
7. SAMSUNG DIGITal everyone s invitedm HL uial K P5067W HL ia HL P6167W List of Parts i Once you have unpacked your TV check to make sure that you have all the Accessories parts shown here If any piece is missing or broken call your dealer Remote Control BP59 00076A Warranty Cards 2 Instruction Manual AAA Batteries Registration Card 1 Safety Guide Quick Guide Anynet Manual Manual Guide Anynet Cable BP68 00429A 01 Connecting VHF and UHF Antennas If you do not have a cable system you will need to connect an antenna to your TV Antennas with 300 ohm Flat Twin Leads If your antenna looks like this it has 300 ohm flat twin leads Place the wires from the twin leads under the screws on the 300 75 ohm adaptor not supplied Use a screwdriver to tighten the screws Plug the adapter into the Air IN terminal on the rear panel Antennas with 75 ohm Round Leads If your antenna looks like this C it is an antenna with 75 ohm round leads Plug the antenna lead into the Air IN terminal on the rear panel Separate VHF and UHF Antennas If you have two separate antennas for your TV one VHF and one UHF you must combine the two antenna signals before connecting the antennas to the TV This procedure requires an optional combiner adaptor available at most electronics shops Connect both an
8. blocking chan nels e The output from Cable Out is not available when Air CATV is set to Cable in the PIP menu our Analog Cable converter box Connecting an Analog Cable Converter Box and a VCR This connection allows you to watch and TV Rear Panel record basic and premium cable channels as well as watch videotapes You should keep your TV selected to Cable IN so that you can use the TV s features When view From ing premium channels or recording with the Cable VCR select Air IN whichever channel is vacant in your area then use the converter box to change channels Caution If you want to record one channel while watching another channel a splitter not included must be added between the cable and Cable IN One output of the splitter goes to Cable OUT and the sec Analog Cable converter box ond output is connected to IN on the cable converter box If you have a mono VCR connect L Mono ee to VCR Audio OUT using only one audio cable Stereo VCR If you have an S VHS VCR use the S Video connections and remove the video cable Do not connect the video cable and the S Video cable to video1 simultaneously When you use a converter box with your TV there may be features that you can not program using the remote control such as programming your favorite channels and blocking chan nels i Connecting CableCARD
9. h the power will shut off Lamp may be defective Please contact a certified technician e It takes about 30 seconds for the TV to warm up so normal brightness may not appear imme diately e The TV has a fan to keep the inside lamp from overheating You ll occasionally hear it working Troubleshooting E If the TV seems to have a problem first try this list of possible problems and solutions If none of these troubleshooting tips apply Note then call your nearest Samsung authorized service center Poor picture quality Poor sound quality No picture or sound Try another channel Try another channel Try another channel Adjust the antenna Adjust the antenna Press the SOURCE button Check all wire connections Make sure the MUTE button is off Make sure the TV is plugged in Check the antenna connections No color wrong colors or tints Picture rolls vertically The TV operates erratically Make sure the program is broadcast Adjust the antenna Unplug the TV for 30 seconds then ed in color Check all wire connections try operating it again Adjust the picture settings if you are using a VCR check the track ing Your remote control does not The TV won t switch on Digital broadcasting screen operate your TV problem Press the Mode button to put your Make sure the wall outlet is working Please check the digital signal remote control into TV mode Make sure the TV is plugged in strength a
10. io input connect to the DIGI TAL AUDIO OUT OPTICAL jack on the TV Be certain to remove the black cover from the optical output before insert ing the cable g e OPTICAL converts the electric signal into an optical light sig nal and transmits it through glass fibers A transmission system of digital audio in the form of a light wave S PDIF format using a glass conductor See page 78 to set the digital output format Dolby Digital or PCM appropriate to you digital audio component TV Rear Panel HDMI DVIIN i Connecting to an Analog Amplifier The AUDIO OUT terminals cannot be used for external speakers You must hook them up to an amplifier When an audio amplifier is connected TV Rear Panel to the AUDIO OUT terminals Decrease the gain volume of the OF audio amplifier and adjust the volume level with the volume control on the TV Remote Control You can use the remote control up to about 23 feet from the TV When using the remote control always point it directly at the TV You can also use your remote control to operate your VCR Cable box DVD player or Samsung Set Top Box POWER Turns the TV on and off P MODE Adjust the TV picture by selecting one of the preset factory settings or select your personal customized picture settings ANTENNA Press to select AIR or CABLE CHANNEL NUMBER Press to di
11. morizing channels selecting a broadcast source memorizing the channels automatic and adding and deleting chan nels manual Selecting the Video Signal Source Before your television can begin memorizing the available channels you must specify the type of signal source that is connected to the TV i e an antenna or cable system Press the A or W button to select Auto 1 Press the MENU button Press the A or Program then press the ENTER button V button to select Channel then press the ENTER button Antenna Antenna Auto Program Add Delete Auto Program Add Delete Favorite Channels Favorite Channels Name Fine Tune Y More Name Fine Tune Y More Move Enter M Return Move Enter T Return 2 Press the ENTER button to select g All available DTV and analog Antenna channels are automatically stored Press the A or W button to select Air or in memory Cable then press the ENTER button Antenna Air Auto Program Add Delete Favorite Channels Name Fine Tune Y More Move Enter LL Return Press the A or W button to select the Antenna connection then press the ENTER button e Air Air antenna signal Cable Cable antenna signal Air Cable Air and Cable antenna signals If the CableCARD is inserted into the CableCARD slot on the rear panel Cable and Air Cable are not a
12. nd input antenna Make sure the remote has batteries Make sure the remote has batteries e The display panel used for the DLP TV is composed of many tiny pixels These pixels may occasionally appear on the screen 15
13. nterval for automatic shut off PIP CONTROLS CHA Press to display the avail able channels in sequence These buttons change channels in the PIP window only CAPTION Controls the caption decoder PRE CH Tunes to the previous channel VCR DVD CONTROLS Controls VCR or DVD functions SOURCE Press to display all of the available video sources i e TV Set Top box VCR DVD DTV CH A V Press to change channels Moves from one set of screen infor mation to the next in TV Guide menu INFO Press to display information on the TV screen Rewind Stop Play Pause Fast Forward RESET If your remote control is not function ing properly take out the batteries and press the reset button for about 2 3 seconds Re insert the batteries and try using the remote control again SAMSUNG Ca Turning the TV On and Off Press the POWER button on the remote control You can also use the POWER button on the front panel Viewing the Menus and On Screen Displays The on screen menu system allows you to control the settings of your TV Access the on screen menu system by pressing the Menu button on the remote control Once the on screen menu appears use the A W lt gt ENTER buttons on your remote control to select menu items and make adjustments You can also view the on screen menu system and make some adjustments using the TV s side panel buttons Viewing the Menus
14. rectly tune to a particular channel Press to select additional channels digital and analog being broadcast by the same station For example to EXIT Press to exit the menu A V lt gt ENTER Press to select highlight up down left or right While using the on screen menus press the ENTER to activate or change a particular item MTS Multichannel Television Stereo Press to choose Stereo Mono or SAP Secondary Audio Program PIP Picture In Picture Displays the available channels in sequence These buttons change channels in the PIP window only select channel 54 3 press 54 STILL then press and 3 Press to pause the current screen VOL VOL ASPECT Press to increase or decrease Press to change the screen size the volume SRS MUTE Activates TruSurround Press to mute the TV sound oe DNle Digital Natural ANYNET Image engine Runs the Anynet view functions and Activates DNle sets up Anynet devices ore SET MENU Displays the main on screen menu CH LIST Displays the channel list FAV CH Favorite Channel Press to switch between your favorite channels MODE Selects a target device to be controlled by the Samsung remote control i e TV STB VCR CABLE or DVD Used during set up of this remote control so that it will work compati bly with other devices Set Top box VCR Cable box DVD etc SLEEP Press to select a preset time i
15. tenna leads to the combiner Plug the combiner into the Cable IN terminal on the rear panel Connecting Cable TV and VCR You can connect different cable systems to your TV including cable without a cable box and cable with a cable box that descrambles some or all channels Cable without a Cable Box If you want to connect cable and you do not need to use a cable box Plug the incoming cable into the Cable IN terminal on the rear panel Cable with a Cable Box that Descrambles All Channels Find the cable that is connected to the ANTENNA OUT terminal on your cable box This terminal might be labeled ANT OUT VHF OUT or simply OUT Connect the other end of this cable to the Cable IN terminal on the rear panel z Q auio vineo s v Av0 4 CHT Connecting an Analog Cable Converter Box This connection allows you to watch cable and premium channels You should keep your TV selected to Cable IN so that you can use the TV features When viewing premium chan nels select Air IN and tune the TV to channel 3 or 4 whichever channel is vacant in your area then use the converter box to change channels You will need two coaxial cables Ky e When you use a converter box with your TV there may be fea tures that you can not program using the remote control such as programming your favorite channels and
16. the old lamp near flammable objects or within the reach of children 5 Be sure to connect this TV directly to an AC wall outlet If the TV s AC plug is connected to a cable box or other source it will not allow for proper cool down time For replacement you will need a 5 91 Inch screwdriver and a pair of gloves 1 Unplug TV then use a screwdriver to Separate the Lamp from the engine by remove the screw holding the handle and pulling it out 2 Remove the Lamp cover To reinstall the Lamp follow these steps in reverse order 3 Remove the screw securing the Lamp by g e Be sure the replacement Lamp is the using a screwdriver same type e After replacing the lamp align the lamp cover with the groove and secure the screws e The TV will not turn on if the lamp cover is not correctly closed as this will acti vate the protective circuit Front Panel LED Indicators The three lights on the front panel indicate the status of your TV Lightis On 9 Light is Blinking Light is Off STAND BY TEMP Indication Standby state The picture will automatically appear in about 15 seconds Auto Timer ON OFF has been set and the set will automatically be turned on in about 25 seconds A cooling fan inside the set is not operating normally Lamp cover on rear of the set is not properly shut Check if the ventilation hole on the rear of the set is blocked because if the inner temperature is too hig
17. vail able Select the antennas to memorize Air Start cable Se Air Cable Start Move Enter T Return When selecting Cable TV system Press the A or W button to select Cable then press the ENTER button Press the A or W button to select Analog or Digital STD HRC or IRC then press the ENTER button e STD HRC and IRC identify various types of cable TV systems Contact your local cable company to identify the type of cable system that exists in your particular area At this point the signal source has been selected Proceed to Storing Channels in Memory Select the cable system Analog STD IRC igital STD Y HRC IRC Move Enter T7 Return Press the gt button to select Start then press the ENTER button to start the auto program The TV begins memorizing all available stations Press the ENTER but ton at any time to interrupt the memoriza tion process Press the EXIT button to exit e The TV MUST be connected to an antenna in order to receive digital TV signals Even if a particular channel is deleted from the memory you can always tune to that channel directly by using the number buttons on the remote control V Input Select the cable system Analog el Picture STD Y HRC EO Sound IRC amp igital s STD m Setup HRC r IRC P Guide Move Enter MT Return Auto Program in progress
Download Pdf Manuals
Related Search