Home

Sagem SAGEMFAST 1500 User's Manual

1. o 00 J slo Add currently associated MAC stations Previous Finish v Once you have done your settings click Finish to save these settings and quit the Setup Wizard Your SAGEM F st 1500 ADSL Router is now set up Go to Troubleshooting on Appendice A if you cannot make a connection to the Internet SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 11 4 3 1 Page 4 12 4 3 SYSTEM 4 Configuring the SAGEM F st 1500 ADSL router In this menu is included the following sub menus gt Time setting see section 4 3 1 Yv vV V WV Password setting and SSID see section 4 3 2 Configuration tools see section 4 3 3 Firware upgrade see section 4 3 4 Reset see section 4 3 5 Time Settings Select your local time zone from the drop down list This information is used for log entries and client filtering STATUS SETUP WIZARD SYSTEM Time Settings Password Settings Configuration Tools Firmware Upgrade Reset WAN LAN WIRELESS NAT FIREWALL ROUTE Qos ADVANCED Save and Reboot Reset Logout Time Settings Set Time Zone Use this setting to insure the time based client filtering feature and system log entries are based on the correct localized time GMT 01 00 Brussels Copenhagen Paris Vilnius v Configure Time Server NTP
2. Windows NT Workstation 2 Inthe Command Prompt window type IPCONFIG RELEASE and press the ENTER key Command Prompt licrosoft Windowse 20060 Uersion 5 08 2195 CG Copyright 19685 19979 Microsoft Corp z gt IPCONFIG RELEASE Jindows 266080 IF Conf igurat ion IF address successfully released For adapter Local Area Connection i 3 Type IPCONFIG RENEW and press the ENTER key Verify that your IP Address is now 192 168 2 xxx your Subnet Mask is 255 255 255 0 and your Default Gateway is 192 168 2 1 These values confirm that your SAGEM F st M 1500 ADSL Router is functioning Command Prompt me Jicrosoft Windows 2000 Version 5 00 2195 C Copyright 19785 1999 Microsoft Corp SEN IPCONFIG RELEASE Jindows 2660 IP Configuration IP address successfully released For adapter Local Area Connection 1 r33 IPCONFIG HENEW Windows 2666 IP Configuration Ethernet adapter Local Area Connection 1 lt 192 168 2 125 Connection specific DNS Suffix d nO Wee k F G IP Address subnet Mask s s se s s we Fl 299 299 299 8 Default Gateway 192 168 2 1 4 Type EXIT and press the ENTER key to close the Command Prompt window Your computer is now configured to connect to the SAGEM F st 1500 ADSL Router SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 3 11 3 Conf
3. Displays WAN connection type and status Click on the button to establish the VC s connection click on the Disconnect button to stop it LAN Wireless Displays system IP settings as well as DHCP Server UPnP and Wireless Status Additional Displays the number of DHCP clients the firmware versions the physical MAC Information address for each media interface and for the SAGEM F st 1500 ADSL Router as well as the hardware version and serial number Security Log Displays events exchanged on your WAN network with the remote equipment Click button saves all the displayed events from the Security Log window within a file on your PC Click button deletes all the events from the Security Log DHCP Client Log Displays information on DHCP clients on your network Refresh In the top of the screen click on this button to refresh the status and the Retresh Security Log SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 7 4 Configuring the SAGEM F st 1500 ADSL router 4 2 SETUP WIZARD menu In this menu is included the following sub menus gt PPP setting see section 4 2 1 gt Channel and SSID see section 4 2 2 gt WEP see section 4 2 3 gt Access control see section 4 2 4 4 2 1 PPP Setting 1 PPP settings 1 PPP settings 2 Channel and SSID Please enter your PPP account information p
4. 20 al 22 23 24 25 26 27 28 29 30 zal 32 z DHCP Client List ip 192 168 2 2 name P1076997 v _copyto 1 w Click Yes to enable or No to disable this function Enter the MAC address in the space provided SAGEM F st 1500 Reference Manual 288053220 04 Page 4 40 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 8 3 URL Blocking The SAGEM F st 1500 ADSL Router allows the user to block access to web sites from a particular PC by entering either a full URL address or just a keyword This feature can be used to protect children from accessing violent or pornographic web sites SS k oe oo S ZAA Save and Reboot Reset Logout STATUS URL Blocking SETUP WIZARD SYSTEM WAN You can block access to certain Web sites from a particular PC by entering either a full URL address or just a LAN keyword of the Web site WIRELESS To specify the particular PC go back to the Access Control page and check the box for Http with URL NAT Blocking in the Normal Filtering Table Disallowed Web Sites and Keywords FIREWALL Access Control MAC Filter URL Blocking Sched
5. Port Range a lo Scheduling Rule Ref Schedule Rule Page Always Blocking J SAGEM F st 1500 Reference Manual 288053220 04 Page 4 39 4 Configuring the SAGEM F st 1500 ADSL router 4 8 2 MAC Filter The SAGEM F st 1500 ADSL Router can also limit the access of hosts within the local area network LAN The MAC Filtering Table allows the SAGEM F st 1500 ADSL Router to enter up to 32 MAC addresses that are not allowed access to the WAN port 3X k sacem i i a S AD Home Save and Reboot Reset Logout STATUS MAC Filter SETUP WIZARD This section helps provides MAC Filter configuration When enabled only MAC addresses configured will have SYSTEM access to your network All other client devices will get denied access This security feature can support up to WAN 32 devices and applies to clients LAN WIRELESS NAT MAC Filtering Table up to 32 computers FIREWALL Access Control MAC Filter URL Blocking Schedule Rule Intrusion Detection DMZ ROUTE Qos ADVANCED MAC Address Control Oves No ID MAC Address m Cer fan CS Ea mna PS a ra m o 11 12 13 14 15 16 17 18 19
6. SAGEM F st 1500 Reference Manual 288053220 04 Page C 4 Reproduction and communication prohibited without the written permission of SAGEM SA Appendix C Cables C 2 2 Wiring Conventions For ADSL connections a cable requires one pair of wires Each wire is identified by different colors For example one wire might be red and the other red with white stripes Also an RJ 11 connector must be attached to both ends of the cable Each wire pair must be attached to the RJ 11 connectors in a specific orientation The following figure illustrates how the pins on the RJ 11 connector are numbered Be sure to hold the connectors in the same orientation when attaching the wires to the pins Na Figure C 2 RJ 11 Connector Pin Numbers gt 2 a3 FFE ol T nm 3 JEg y 5t EP Ese ag es jii jill rei 11 T2 Ri TRZ T2 Fi TRZ 123456 123456 123456 Ba Jack 6x4 Jack x4 Jack T Tip R Ring Figure C 3 RJ 11 Pinouts Pin Signal Name Wire Color a Notused 2 Line 2 Tip Black or White Orange Red or Blue White 4 Line1Tip Green or White Blue 5 Line2Ring Yellow or Orange White 6 nousa SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page C 5 Appendix C Cables SAGEM F st 1500 Reference Manual 288053220 04 Page C 6 Reproduction and communication prohibited without the written permission o
7. 00 00 oo Slo Eloo oo Add currently associated MAC stations ha in M mi M J M oo M so w oO iJ m en M k Click Yes to turn on the filtering function or No to disable this function If you have enabled this function you can enter the client MAC addresses that you want to filter You can give up to 32 client stations SAGEM F st 1500 Reference Manual 288053220 04 Page 4 26 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 6 3 Security To make your wireless network safe you should turn on the security function The SAGEM F st 1500 ADSL Router supports WEP Wired Equivalent Privacy WPA Wi Fi Protected and 802 1x security mechanisms Ssacem GE Home Save and Reboot Reset Logout STATUS Security SETUP WIZARD SYSTEM WAN LAN WIRELESS Channel and SSID Access control Security WEP WPA 802 1 NAT FIREWALL ROUTE Qos ADVANCED The router can transmit your data securely over the wireless network Matching security mechanisms must be setup on your router and wireless client devices You can choose the allowed security mechanisms in this page and configure them in the sub pages Allowed Client Type No WEP No WPA SAGEM F st 1500 Reference Manual 288053220 04 Repr
8. 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 57 4 Configuring the SAGEM F st 1500 ADSL router The following items are included on this information page Parameter Description Operation Mode It allows to specify the ADSL standards to operate with The following standards below are supported gt Automatic 71 413 Issue 2 G 992 1 G DMT G 992 2 G Lite G 992 5 ADSL 2 Status Line Status Shows the current status of the ADSL line connection Link Type Shows the current Link Type Interleaved or Fast Data Rate Upstream Maximum upstream data rate Downstream Maximum downstream data rate Operation Data Defect Indication Noise Margin Maximum upstream and downstream noise margin Attenuation Maximum reduction in the strength of the upstream and downstream signal Fast Path FEC Correction There are two latency paths that may be used fast and interleaved For either path a forward error correction FEC scheme is employed to ensure higher data integrity For maximum noise immunity an interleaver may be used to supplement FEC Interleaved Path FEC Correction An interleaver is basically a buffer used to introduce a delay allowing for additional error correction techniques to handle noise Interleaving slows the data flow and may not be optimal for real time signals such as video transmission Fast Path CRC Error dd The number
9. Note The OAM functions provided are as follows Segment and end to end flow F4 and F5 management by VC AlS RDI functions Response to loopback cells F4 or F5 Response to continuity check CC enable disable cells PPP characteristics IP address Automatic negotiation Connect Type Always Connected ADSL characteristics Maximum upstream rate 896 kbit s Maximum downstream rate 8160 kbit s Simple latency fast or interleaved Note The user can revert to the default configuration via the HTTP interface E 5 Default configuration for advanced functions Advanced functions Function Mode State Value characteristics SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page E 3 Appendix E Default configuration SAGEM F st 1500 Reference Manual 288053220 04 Page E 4 Reproduction and communication prohibited without the written permission of SAGEM SA SAGEM SA Networks Division S SAGEM Le Ponant de Paris 27 rue Leblanc 75512 PARIS CEDEX 15 FRANCE T l 33 1 40 70 63 63 Fax 33 1 40 70 66 40 http www sagem com SAGEM SA Soci t anonyme directoire et conseil de surveillance au capital de 35 500 000 Si ge social 27 rue Leblanc 75512 PARIS CEDEX 15 562 082 909 R C S PARIS
10. Password or MD5 Authentication key Code RIP sends routing update messages at regular intervals and when the network topology changes When a router receives a routing update that includes changes to an entry it updates its routing table to reflect the new route RIP routers maintain only the best route to a destination After updating its routing table the router immediately begins transmitting routing updates to inform other network routers of the change SAGEM F st 1500 Reference Manual 288053220 04 Page 4 50 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 9 3 Routing Table S SAGEM STATUS SETUP WIZARD SYSTEM WAN LAN WIRELESS NAT FIREWALL ROUTE Static Route RIP Routing Table Qos ADVANCED Pics AR Home Reset Logout Routing Table The content of run time Routing Table Flags Network Address Netmask Gateway Interface G 192 168 2 0 AEE E A directly LAN c 127 0 0 1 Hea ibaa directly Loopback Flags C directly connected S static R RIP I ICMP Redirect Parameter Description Indicates the route status C Direct connection on the same subnet S Static route R RIP Routing Information Protocol assigned route ICMP Internet Control Message Protocol Redirect route Network Address Destination IP address The subnetwork associated with the destination This i
11. Select your country page can be accessed from the home page It enables the user to choose a country for Wi Fi area S SAGEM STATUS SETUP WIZARD SYSTEM WAN LAN WIRELESS NAT FIREWALL ROUTE Qos ADVANCED Home Save and Reboot Reset Country Selection Please select a country to configure the Access Point for your location Select Country Warning After applying these settings you will only be able to change them by resetting the Access Point to Factory Defaults To access the various menus of the HTTP configurator it is imperative to validate the country choosen by clicking on the Apply button The choice of country determines the range of channels that you can use in Wi Fi mode SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 3 4 Configuring the SAGEM F st 1500 ADSL router By default no password is required to access the home page screen However a password can be created on your modem router through the Password Setting see subsection 4 3 2 under SYSTEM menu If a password is created the login screen below is displayed Enter this password and then click on the LOGIN button to access the HTTP configurator Password Please enter correct password for Administrator Access Thank you We suggest that you use Internet Explorer 5 5 or above at a minimum of 1024x768 resolution Co
12. Use the Backup tool to save the router s current configuration to a file named backup bin on your PC You can then use the Restore SYSTEM tool to restore the saved configuration to the router Alternatively you can use the Restore to Factory Defaults tool to force the router Time Settings to perform a power reset and restore the original factory settings Password Settings Firmware Upgrade O Restore from saved Configuration file backup bin s Reset O Restore router to Factory Defaults AN LAN WIRELESS NAT FIREWALL ROUTE Qos ADVANCED Choose a function and click Next gt Backup allows you to save the SAGEM F st 1500 ADSL Router s configuration to a file gt Restore can be used to restore the saved backup configuration file gt Restore to Factory Defaults resets the SAGEM F st 1500 ADSL Router to the original settings You will be asked to confirm your decision SAGEM F st 1500 Reference Manual 288053220 04 Page 4 14 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 3 4 Firmware Upgrade Use this screen to update the firmware or user interface to the latest versions Download the upgrade file from the Sagem web site and save it to your hard drive In the Upgrade Target field choose Firmware Then click Browse to look for the downloaded file Click Apply Check the Status page Info
13. 2 Configuring your Windows computer 3 2 1 On Windows 98 Me You may find that the instructions in this section do not exactly match your version of Windows This is because these steps and screen shots were created from Windows 98 Windows Millennium Edition is similar but not identical to Windows 98 1 On the Windows desktop click Start Settings Control Panel 2 In Control Panel double click the Network icon Ed Gani Fanal e gt u a fw J Herk univer Up Wap Dime Oitconnesct Cut ddar eal Camniiol P rial Accessbik Add Wem Add Hemove L PPA Sis da A Togia F aA i 4 nt Ea a Find Fasi Foris Game Use the seinge in Contralers Control Panel to parsonalize your ap di cemputer m A Lie lodste hal hlocdems Taleg an barn to view tke description a tM ODBC Data Passwgids Sunes 3l h REEE a Technical Si Te In the Network window under the Configuration tab double click the TCP IP item listed for your network card 4 In the TCP IP window select the IP Address tab If Obtain an IP address automatically is already selected your computer is already configured for DHCP If not select this option SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 3 3 3 Configuring Client Computer Network a Dierk for Micol Melworka f SMC EZ Card 107100 MCI211
14. 35 4 36 4 37 4 11 Advanced 4 11 1 ADSL 4 11 2 Remote Management 4 11 3 SNMP 11 4 UPnP 11 5 DDNS 4 12 Finding the MAC address of a Network Card A Appendix A Troubleshooting B Appendix B Safety warnings B 1 Safety warnings 1 Safety levels on the mains adapter unit B 1 B 1 2 Safety levels on the SAGEM F st 1500 unit B 2 CE declaration of conformity C Appendix C CABLES C 1 Ethernet cable C 1 1 Specifications C 1 2 Wiring Conventions C 1 3 RJ 45 Port Connection C 1 4 Pin Assignments C 2 ADSL Cable C 2 1 Specifications C 2 2 Wiring Conventions D Appendix D Technical specifications D 1 Mechanical Characteristics Displays D 2 Electrical Characteristics D 3 Soft Component Features D 4 Radio Features D 5 Environmental characteristics E Appendix E Default configuration E 1 Default user name and password for HTTP access E 2 Default language for HTTP User Interface E 3 Default configuration on the local area network side E 4 Default configuration on the wide area network side E 5 Default configuration for advanced functions 4 56 4 56 B 1 B 2 B 2 B 2 C 1 C 2 C32 C 2 C2 C 3 C 4 C 5 D 7 E 1 E 2 SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM sa Page 0 3 List of figures Figure 2 1 Front Panel Figure 2 2 Rear Panel Figure 2 3 Installing with a Splitter Figure 2
15. Attach to Your Network Using Ethernet Cabling The four LAN ports on the SAGEM F st 1500 ADSL Router auto negotiate the connection speed to 10 Mbps Ethernet or 100 Mbps Fast Ethernet as well as the transmission mode to half duplex or full duplex Use RJ 45 cables to connect any of the four LAN ports on the SAGEM F st 1500 ADSL Router to an Ethernet adapter on your PC Otherwise cascade any of the LAN ports on the SAGEM F st 1500 ADSL Router to an Ethernet hub or switch and then connect your PC or other network equipment to the hub or switch When inserting an RJ 45 connector be sure the tab on the connector clicks into position to ensure that it is properly seated Do not plug a phone jack connector into an RJ 45 port This may damage the SAGEM F st 1500 ADSL Router all Ethernet ports Use Category 3 4 or 5 for connections that operate at Use 100 ohm shielded or unshielded twisted pair cable with RJ 45 connectors for t 10 Mbps and Category 5 for connections that operate at 100 Mbps Make sure each twisted pair cable length does not exceed 100 meters 328 feet 2 3 6 Connect the Power Adapter Plug the power adapter into the power socket on the rear of the SAGEM F st 1500 ADSL Router and the other end into a power outlet Check the power indicator on the front panel is lit If the power indicator is not lit refer to Troubleshooting on Appendice A In case of a power input failure the SAGEM F st 1500 ADSL
16. DSCP Direct to YC VCI v Almost fields have been filled please set up these last ones Parameter Description Local Address select Mac addr IP range This router or Any Remote Address Select IP range or Any In the fields Local Address or Remote Address if you choose Mac addr L IP range an other screen appears and you may enter the Mac address or a IP address range or the IP address on the local or remote part For example in the screen above IP range has been selected After having entered several services classes the following screen appears Ssacem i STATUS l SETUP WIZARD Traffic Mapping SYSTEM WAN LAN Rule Name Traffic Description Save and Reboot Reset Logout Up to 16 rules can be defined to classify traffic into Diffserv forwarding groups and outgoing VCs Map to Diffserv Outgoing YC Configure WIRELESS ftp1 from 192 168 2 3 FTP BE VC1 NAT ftp2 from 192 168 2 2 FTP vC1 FIREWALL Qos Traffic Mapping Traffic Statistics ADVANCED SAGEM F st 1500 Reference Manual 288053220 04 Page 4 54 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router This button allows to modify all parameters of each traffic class This button allows to delete a traffic class This button allows to move up the matching priority of the selected rule Down This button allows to move down the matching
17. Reset Logout STATUS RIP SETUP WIZARD SYSTEM WAN General RIP parameter LAN RIP mode Disable Enable WIRELESS Auto summary Disable Enable NAT Table of current interface RIP parameter Please enter the following configuration parameters FIREWALL z 3 i icati icati Interface Operation Mode Version Poison Authentication Authentication ROUTE Reverse Required Code LAN Disable Disable None Static Route RIP WLAN Disable Disable None Routing Table ATM1 gos ADVANCED Disable Disable None ATM2 Disable v Disable None ATM3 Disable Disable None ATM4 Disable b Disable None ATMS Disable v Disable None ATM6 Disable Disable None eee ee Disable 0 _ Disable Gag None ATMS Disable v Disable None PPPoEL Disable v Disable None PPPoE2 Disable Disable None PPPoES Disable Disable None PPPoE4 Disable Disable None PPPoES Disable Disable None PPPoE6 Disable Disable None PPPoE Disable Disable None PPPoES Disable Disable None SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permiss
18. Router will automatically restart and begin to operate once the input power is restored SAGEM F st 1500 Reference Manual 288053220 04 Page 2 10 Reproduction and communication prohibited without the written permission of SAGEM SA 2 Description and physical installation 2 4 Powering up the SAGEM F st 1500 ADSL router gt Check that the SAGEM F st 1500 router is connected correctly to the electrical power supply network see section 2 3 2 gt Set the I O switch to I bottom position Initially the PWR LED and all the ETHERNET LEDs will come on After a certain period only the PWR LED will remain lit the extreme right ETHERNET LED is slowly blinking the ALM LED will come on and the WLAN LED only for the SAGEM F st 1500WG will then come on if the wireless module is installed and active and finally the ADSL LED will start blinking SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 2 11 2 Description and physical installation SAGEM F st 1500 Reference Manual 288053220 04 Page 2 12 Reproduction and communication prohibited without the written permission of SAGEM SA 3 Configuring Client Computer This chapter covers gt the TCP IP Configuration Section 3 1 gt the configuration of your Windows computer Section 3 2 gt the configuration of your Mac computer section 3 3 SAGEM F st 1500 Reference Manua
19. Te g TCPAP Dial Up Adapter Y TCPAP gt SMC EZ Card 10 100 SMC1211 Ts Fedo be I I i SEAE FoF TT 5 Windows may need your Windows 95 98 Me CD to copy some files After it finishes copying it will prompt you to restart your system Click Yes and your computer will restart System Settings Change TCP IP Configuration Setting Primary DNS Server Secondary DNS Server Default Gateway Host Name SAGEM F st 1500 Reference Manual 288053220 04 Page 3 4 Reproduction and communication prohibited without the written permission of SAGEM SA D 3 Configuring Client Computer isable HTTP Proxy You need to verify that the HTTP Proxy feature of your web browser is disabled This is so that your browser can view the SAGEM F st 1500 ADSL Routers HTML configuration pages The following steps are for Internet Explorer In Internet Options Ei ES ternet Explorer Open Internet Explorer Click the Stop button then click Tools Internet Options In the Internet Options window click the Connections tab Next click the LAN Settings button Clear all the check boxes Click OK and then click OK again to close the Internet Options window General Security Content Connections Programs Advanced 2 Dial up settings Add Hemose betting f Hever dalla connection Use the Internet Connection Wizard to connect pour computer to the Internet E jal whenever a
20. Urda Add edit Hemare Dorian Sitti Search Order 4c it Renee cons _ 8 Windows may copy some files and will then prompt you to restart your system Click Yes and your computer will shut down and restart TCP IP Configuration Setting Primary DNS Server Secondary DNS Server Default Gateway Host Name Disable HTTP Proxy You need to verify that the HTTP Proxy feature of your web browser is disabled This is so that your browser can view the SAGEM F st 1500 ADSL Routers HTML configuration pages refer to Internet Explorer on 3 2 1 Obtain IP Settings from SAGEM F st 1500 ADSL Router Now that you have configured your computer to connect to your SAGEM F st 1500 ADSL Router it needs to obtain new network settings By releasing old DHCP IP settings and renewing them with settings from your SAGEM F st 1500 ADSL Router you can also verify that you have configured your computer correctly SAGEM F st 1500 Reference Manual 288053220 04 Page 3 10 Reproduction and communication prohibited without the written permission of SAGEM SA 3 Configuring Client Computer 1 On the Windows desktop click Start Programs Command Prompt ean JF Accessories Startup Documents 1 Command Prompt Settings gt J Windows NT Explorer i Barricade Utility H _ a Startup m E WLAN Bridge Utility A Find 8 Administrative Tools Common gt
21. You can automatically maintain the system time on your ADSL router by synchronizing with a public time server over the Internet Enable Automatic Time Server Maintenance When you enable this option you will need to configure two different time servers use the options below to set the primary and secondary NTP servers in your area Primary Server 129 132 2 21 Europe Secondary Server 130 149 17 8 Europe For accurate timing of log entries and system events you need to set the time zone Select your time zone from the drop down list If you want to automatically synchronize the SAGEM F st 1500 ADSL Router with a public time server check the box to Enable Automatic Time Server Maintenance Select the desired servers from the drop down menu SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA 4 3 2 4 Configuring the SAGEM F st 1500 ADSL router Password Settings Use this page to change the password for accessing the management interface of the SAGEM F st 1500 ADSL Router Passwords can contain from 3 to 12 alphanumeric characters and are case sensitive S SAGEM STATUS SETUP WIZARD SYSTEM Time Settings Password Settings Configuration Tools Firmware Upgrade Reset WIRELESS NAT FIREWALL ROUTE Qos ADVANCED Bias AAR Home Save and Reboot Reset Logout Password Settings Set a password
22. a Save amp Reboot process to store the modifications in the flush memory You can click the Save amp Reboot button at the top of page This section on the left of the Home screen contains the following menus Y VV VV VV VV VWV WV STATUS see section 4 1 SETUP WIZARD see section 4 2 SYSTEM see section 4 3 WAN see section 4 4 LAN see section 4 5 WIRELESS see section 4 6 NAT see section 4 7 FIREWALL see section 4 8 ROUTE see section 4 9 QoS see section 4 10 ADVANCED see section 4 11 On the Home screen you can choose the language in which the HTTP pages will be displayed by clicking the appropriate flag French or English By default the language in use is English SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 5 4 Configuring the SAGEM F st 1500 ADSL router 4 1 STATUS The Status page displays ADSL WAN LAN connection status firmware and hardware version numbers illegal attempts to access your network as well as information on DHCP clients Save connected to your network The security log may be saved within a file by clicking the button and choosing a location on your computer scroll down to view more information on the STATUS page X STATUS SETUP WIZARD ADSL WIRELESS Status Operation Mode Up Stream Down Stream MULTIMODE 0 Kb O Kb NAT DOWN FIREWALL ROU
23. are B 1 1 Safety levels on the mains adapter unit Two pole mains AC connector Primary power supply access HPV Miniature DC socket DC power supply port SELV B 1 2 Safety levels on the SAGEM F st 1500 unit Power Inlet DC power supply port SELV LAN Ports 10 100BASE T Ethernet port SELV ADSL Port ADSL line port TNV3 1 Hazardous Primary Voltage circuit Safety Extra Low Voltage circuit Telecommunication Network Voltage level 3 circuit SAGEM F st 1500 Reference Manual 288053220 04 Page B 2 Reproduction and communication prohibited without the written permission of SAGEM SA Appendix B Safety warnings B 2 CE declaration of conformity Products bearing this symbol are compliant with the EMC regulations and the low voltage directive published by the European Commission SAGEM SA declares that the SAGEM F st 1500 product is compliant with the requirements of European Directives 1995 5 CE and the main requirements of directives 89 336 CEE dated 03 05 1989 and 73 23 CEE dated 19 02 1973 and that it effectively uses the spectrum assigned for terrestrial or space radio communications The CE declaration of conformity concerning the SAGEM F st 1500 is drawn up within the context of the R amp TTE directive Conformity is presumed by full compliance with the harmonized European standards Safety EN 60950 Ed 04 2002 ITU T K 21 EMC EN 301 489 1 Ed V1 4 1 2002 EN 301 489 17 Ed V1 2 1 2002 EN
24. context of SNMP an unsolicited message can be sent by an agent to management station The purpose is to notify the management station of some unusual event No IP Address Community Version 1 Disabled Disabled Disabled Disabled Disabled SNMP Setting A computer attached to the network called a Network Management Station NMS can be used to access this information Access rights to the agent are controlled by community strings To communicate with the SAGEM F st 1500 ADSL Router the NMS must first submit a valid community string for authentication Community A community name authorized for management access Management access is restricted to Read Only Read or Read Write Write Valid Enables disables the entry SAGEM F st 1500 Reference Manual 288053220 04 Page 4 60 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router Up to five community names may be entered SNMP Trap Specify the IP address of the NMS to notify when a significant event is detected by the agent When a trap condition occurs the SNMP agent sends an SNMP trap message to any NMS specified as a trap receiver Parameter Description IP Address Traps are sent to this address when errors or specific events occur on the network Community A community string password specified for trap management Enter a word something other than public or pri
25. nemak connector I not present Aleve dial my deraut connection Lunrentdetaul Hone Set Wehault M Betton sustem secuii check beroe dialing Local 4rea Network LAN settings LAN Settings OK Cancel Apply SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 3 5 Local Area Network LAH Settings Bades lait Le Pita etree ay Bypass prom server for local addtesses SAGEM F st 1500 Reference Manual 288053220 04 Page 3 6 Reproduction and communication prohibited without the written permission of SAGEM SA 3 Configuring Client Computer Obtain IP Settings from SAGEM F st 1500 ADSL Router Now that you have configured your computer to connect to your SAGEM F st 1500 ADSL Router it needs to obtain new network settings By releasing old DHCP IP settings and renewing them with settings from your SAGEM F st 1500 ADSL Router you can also verify that you have configured your computer correctly 1 On the Windows desktop click Start Run 2 Type WINIPCFG and click OK It may take a second or two for the IP Configuration window to appear 3 In the IP Configuration window select your network card from the drop down menu Click Release and then click Renew Verify that your IP address is now 192 168 2 xxx your Subnet Mask is 255 255 255 0 and your Defa
26. of Fast Path Cyclic Redundancy Check errors Interleaved Path CRC Error J The number of Interleaved Path Cyclic Redundancy Check errors Loss of Signal Defect oO Momentary signal discontinuities Fast Path HEC Error Fast Path Header Error Concealment errors Interleaved Path HEC Error Interleaved Path Header Error Concealment errors Received Cells Number of cells received Transmitted Number of cells transmitted Cells SAGEM F st 1500 Reference Manual 288053220 04 Page 4 58 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 11 2 Remote Management By default management access is only available to users on your local network However you can also manage the SAGEM F st 1500 ADSL Router from a remote host by entering the IP address of a remote computer on this screen Check the Enabled check box and enter the IP address of the Host Address and click Apply STATUS Remote Management SETUP WIZARD Set the remote management of the router If you want to manage the router from a remote location outside of SYSTEM the local network you must also specify the IP address of the remote PC WAN LAN Enabled WIRELESS NAT FIREWALL ROUTE Qos ADSL Remote Management SNMP UPnP DDNS Host Address 0 0 0 0 Subnet Mask 255 255 255 0 Port Number 8080 manage the SAGEM F st 1500 A
27. permitted through the WAN interface The default is to permit all outgoing traffic X k Se ii S ZA Home Save and Reboot Reset STATUS Access Control SETUP WIZARD Access Control allows users to define the traffic type permitted or not permitted to WAN port service This page SYSTEM includes IP address filtering and MAC address filtering WAN LAN Enable Filtering Function yYes No WIRELESS NAT FIREWALL Enable Service Access Control RIP UDP 520 MAC Filter URL Blocking Schedule Rule Intrusion Detection DMZ Inbound Default Rules BOOTP UDP 67 Normal Filtering Table up to 10 computers Client PC Client PC IP Schedule ROUTE Description Address alen Seel Rule SalI Qos No Valid Filtering Rule ADVANCED The following items are on the Access Control screen Parameter Description Enable Filtering Function Click Yes to turn on the filtering function Normal Filtering Table Displays the IP address or an IP address range filtering table To add the PC to the filtering table 1 Click Add PC on the Access Control screen 2 Define the appropriate settings for client PC services 3 Click OK and then click SAVE SETTINGS to save your settings SAGEM F st 1500 Reference Manual 288053220 04 Page 4 38 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router SAGEM
28. priority of the selected rule m Joo 4 10 2 Traffic statistics In the QoS menu select Traffic Statistics the following screen appears STATUS SETUP WIZARD Traffic Statistics SYSTEM This page shows the WAN outbound traffic statistics of all the Diffserv forwarding groups in the last 12 WAN hours automatically updated every 5 mins LAN Forwarding WIRELESS Behavior NAT FIREWALL ROUTE Qos Traffic Mapping Traffic Statistics ADVANCED Average sent byte sec 1 hour 6 hour 12 hour BE Forwarding Average dropped byte sec Behavior 1 hour 6 hour 12 hour BE Click on this button to update the WAN outbound traffic screen SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 55 4 Configuring the SAGEM F st 1500 ADSL router 4 11 Advanced In this menu is included the following sub menus gt ADSL see section 4 11 1 gt Remote Management see section 4 11 2 gt SNMP see section 4 11 3 gt UPnP see section 4 11 4 gt DDNS see section 4 11 5 4 11 1 ADSL ADSL ADSL Asymmetric Digital Subscriber Line is designed to deliver more bandwidth downstream from the central office to the customer site than upstream This section is used to display the ADSL operation type and its status SAGEM F st 1500 Reference Manual 288053220 04 Page 4 56 Reproduction and communication prohibi
29. screenshots were created using Mac OS 10 2 Mac OS 7 x and above are similar but may not be identical to Mac OS 10 2 Follow these instructions 1 Pull down the Apple Menu a Click System Preferences Finder File Edit View About This Mac Get Mac OS X Software System Preferences Dock p Location p Recent Items b Force Quit Sleep Restart Shut Down Log Out 0 2 Double click the Network icon in the Systems Preferences window 59 System Preferences Personal Ee SS 2 BE Desktop Dock General International Legin items My Account Screen Effects Hardware gt koo x F gt 6 m Pv ff COs A DVDs Colorsyret Displays Energy Keyboard MOUSE 50 ure Sal VET Internet amp Network a Q is Internet QuickTime Sharing System a EG jaa u gp ACCOUNTS Classic Date amp Time Sofware Speech Startup Disk Universal Liguria te Arrety SAGEM F st 1500 Reference Manual 288053220 04 Page 3 20 Reproduction and communication prohibited without the written permission of SAGEM SA 3 Configuring Client Computer 3 If Using DHCP Server is already selected in the Configure field your computer is already configured for DHCP If not select this Option a4 hetveori 2 Locacon Ainu L Show Built in Echennes Ey EPOPAPS PPPoE appietam proxies Configure Using DMF el DNS Serre eter F Acdvess IELAI Duhngl bisik 2549 3959 FS 5 Searih
30. to restrict management access to the router If you want to manage the router from a remote location outside of the local network you must also specify the IP address of the remote PC You can do this in the Advanced Remote Management menu e Current Passw ord Idle Time Out 10 Min B Idle Time 0 NO Time Out New Password Re Enter Password for Verification If you lost the password or you cannot gain access to the user interface press the blue reset button on the rear panel holding it down for at least five seconds to restore the factory defaults The default password is empty Enter a maximum Idle Time Out in minutes to define a maximum period of time for which the login session is maintained during inactivity If the connection is inactive for longer than the maximum idle time it will perform system logout and you have to log in again to access the management interface The default timeout is fixed to 10 minutes SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 13 4 Configuring the SAGEM F st 1500 ADSL router 4 3 3 Configuration tools Use the Tools menu to backup the current configuration restore a previously saved configuration restore factory settings update firmware and reset the SAGEM F st 1500 ADSL Router See ii Home Reset Logout STATUS Configuration Tools SETUP WIZARD
31. use WEP 3 WEP Enable or disable WEP module function Disable O Enable 4 Access control WEP Mode 64 bit 128 bit Key Entry Method Hex O ASCII Static WEP Key Setting 10 26 hex digits for 64 WEP 128 WEP Default Key ID 1 Passphrase 1 32 characters Key 1 0101010101 E Key 2 0202020202 Key 3 0303030303 Key 4 0404040404 Clear Parameter Description WEP module function Select Disable or Enable key to use or not WEP module function Remark It is advised to select the Enable key WEP Mode Select 64 bit or 128 bit key to use for encryption Key Entry Method Select Hex or ASCII key to use a Key Entry Method Hexadecimal or ASCII To validate the WEP security protection you should to set the same parameters for the SAGEM F st 1500 ADSL Router and all your wireless clients You may automatically generate encryption keys or manually enter the keys To generate the key automatically with passphrase check the Passphrase box enter a string of characters Select the default key from the drop down menu Click Next y The passphrase can consist of up to 32 alphanumeric characters To manually L configure the encryption key enter five hexadecimal pairs of digits for each 64 bit key or enter 13 pairs for the single 128 bit key A hexadecimal digit is a number or letter in the range 0 9 or A F Note that WEP protects data transmitted between wireless nodes bu
32. 20 04 Page D 4 Reproduction and communication prohibited without the written permission of SAGEM SA Appendix D Technical specifications Operating Channels IEEE 802 11b compliant 11 channels US Canada 13 channels ETSI 2 Channels Spain 4 Channels France 14 channels Japan Operating Channels IEEE 802 11g compliant 13 channels US Canada Europe Japan RF Output Power Modulation Rate Output Power dBm 802 11b 1Mbps 16 dBm 802 11b 2Mbps 16 dBm 802 11b 5 5Mbps 16 dBm 802 11b 11Mbps 16 dBm Modulation Rate Output Power dBm 802 11g 6Mbps 15 dBm 802 119 9Mbps 15 dBm 802 11g 12Mbps 15 dBm 802 11g 18Mbps 15 dBm 802 11g 24Mbps 15 dBm 802 11g 36Mbps 15 dBm 802 11g 48Mbps 15 dBm 802 11g 54Mbps 15 dBm Sensitivity Modulation Rate Receiver 2 412 2 484 HGz Sensitivity dBm 802 11b 1Mbps 90 dBm 802 11b 2Mbps 88 dBm 802 11b 5 5Mbps 85 dBm 802 11b 11Mbps 84 dBm SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page D 5 Appendix D Technical specifications Modulation Rate Receiver Sensitivity Typical dBm 802 11g 6Mbps 88 dBm 802 11g 9Mbps 87 dBm 802 11g 12Mbps 84 dBm 802 11g 18Mbps 82 dBm 802 11g 24Mbps 79 dBm 802 11g 36Mbps 75 dBm 802 11g 48Mbps 68 dBm 802 11g 54Mbps
33. 4 Installing without a splitter Figure C 1 RJ 45 Ethernet Connector Pin Numbers Figure C 2 RJ 11 Connector Pin Numbers Figure C 3 RJ 11 Pinouts SAGEM F st 1500 Reference Manual 288053220 04 Page 0 4 Reproduction and communication prohibited without the written permission of SAGEM sa 1 Introduction This chapter covers gt an overview of the SAGEM F st 1500 router Section 1 1 gt the Features and Benefits Section 1 2 gt the Applications of the SAGEM F st 1500 router Section 1 3 gt the composition of the supply Section 1 4 gt the IT prerequisites Section 1 5 SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 1 1 1 Introduction Congratulations on your purchase of the SAGEM F st 1500WG IEEE 802 11g ADSL Router hereafter referred to as the SAGEM F st 1500WG ADSL Router We are proud to provide you with a powerful yet simple communication device for connecting your local area network LAN to the Internet For those who want to surf the Internet in the most secure way this router provides a convenient and powerful solution 1 1 About the SAGEM F st 1500WG ADSL Router The ADSL Router provides Internet access to multiple users by sharing a single user account Support is provided for both wired and wireless devices New technology provides wireless security via Wired Equivalent Privacy WEP encr
34. 55022 Ed 09 1998 A1 2000 A2 2003 EN 55024 Ed 09 1998 A1 2001 A2 2003 CISPR 22 Ed 1997 A1 2000 AS NZS CISPR 22 Ed 2002 Radio specific to SAGEM F st 1500WG EN 300 328 1 Ed 12 2001 EN 300 328 2 Ed 12 2001 EN 301 489 1 Ed 08 2002 EN 301 489 17 Ed 08 2002 SAR EN 50371 Limits of human exposure to electromagnetic fields The radio frequency bands authorized for wireless transmission in IEEE 802 11b g depend on national regulations In most European countries the authorized channels are channels 1 to 13 2400 2483 5 MHz band gt In France for a maximum transmitted power of 100 mW within a building channels 10 to 13 2446 5 2483 5 MHz band are authorized throughout the country and channels 1 to 13 2400 2483 5 MHz band are authorized in 58 departments decision N 02 1008 of ART dated 31 10 2002 The list of departments can be viewed on the ART WEB site SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page B 3 Appendix B Safety warnings SAGEM SA cannot accept any liability if current regulations are not observed at the place of installation The CE declaration of conformity for the SAGEM F st 1500 is included in the form of a file with pdf extension in the product delivery CD ROM SAGEM F st 1500 Reference Manual 288053220 04 Page B 4 Reproduction and communication prohibited without the written permis
35. 68 dBm SAGEM F st 1500 Reference Manual 288053220 04 Page D 6 Reproduction and communication prohibited without the written permission of SAGEM SA Appendix D Technical specifications D 5 Environmental characteristics SAGEM F st 1500WG complies with the following standards Temperature IEC 68 2 14 0 to 50 degrees C Standard Operating 40 to 70 degrees C Non operation Humidity 10 to 90 Non condensing Vibration IEC 68 2 36 IEC 68 2 6 Shock IEC 68 2 29 Drop IEC 68 2 32 IEEE Standards IEEE 802 3 802 3u 802 119 802 1d ITU G dmt ITU G Handshake ITU T 413 issue 2 ADSL full rate Standards Conformance Electromagnetic Compatibility CE ETSI R amp TTE FCC part 15 class B amp FCC part 68 ETS 300 328 ETS 300 826 Safety CSA NRTL UL1950 CSA 22 2 950 GS EN60950 CB IEC60950 ITU K21 SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page D 7 Appendix D Technical specifications Internet Standards RFC 826 ARP RFC 791 IP RFC 792 ICMP RFC 768 UDP RFC 793 TCP RFC 783 TFTP RFC 1483 AAL5 Encapsulation RFC 1661 PPP RFC 1866 HTML RFC 2068 HTTP RFC 2364 PPP over ATM RFC 3261 SIP Passthrough SAGEM F st 1500 Reference Manual 288053220 04 Page D 8 Reproduction and communication prohibited without the written permission of SAGEM SA E Appendix E Default
36. ADSL Router s management interface enter the default IP address of the SAGEM F st 1500 ADSL Router in your web browser http 192 168 2 1 Validate by pressing Enter The home page will be displayed in the Web browser Nota This home differs depending on the model e SAGEM F st 1500 e SAGEM F st 1500WG SAGEM F st 1500 The Information page can be accessed from the home page It takes the user to the different menus of the HTTP configurator STATUS N STATUS SETUP WIZARD SYSTEM Refresh WAN LAN ADSL WIRELESS Status Operation Mode Up Stream Down Stream NAT DOWN MULTIMODE 0 Kb 0 Kb FIREWALL WAN ROUTE z C Status YCC Protocol Username Public IP Qos 1 DOWN Connect 8 35 V C MUX PPPoA eer eae ADVANCED Lei LAN Wireless IP Address Subnet Mask DHCP Server Wireless Channel UPnP 192 168 2 1 255 255 255 0 Enabled Enabled 6 Enabled Additional information Runtime Code Version F st 1500WG Yer 2 08 d lan 28 2005 12 07 45 Boot Code Version 0 62 ADSL Modem Code Version 03 00 14 2474 Serial Num 4413034036 Hardware Version 01 LAN MAC Address 00 60 4C 34 30 00 Wireless MAC Address 00 60 4C 34 30 02 WAN MAC Address 00 60 4C 34 30 01 Numbers of DHCP Clients 1 SAGEM F st 1500 Reference Manual 288053220 04 Page 4 2 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router SAGEM F st 1500WG The
37. DSL Router For remote management via WAN IP address you need to connect by using default port 8080 Simply enter WAN IP address followed by 8080 for example http 212 120 68 20 8080 If you check Enabled and specify an IP address of 0 0 0 0 any remote host can The Subnet Mask allows to limit IP source address to a range of sub networks SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 59 4 Configuring the SAGEM F st 1500 ADSL router 4 11 3 SNMP Use the SNMP configuration screen to display and modify parameters for the Simple Network Management Protocol SNMP SNMP In the context of SNMP a relationship between an agent and a set of SNMP managers defines security characteristics The community concept is a local one defined at the agent The agent establishes one community for each desired combination of authentication access control and proxy characteristics Each community is given a unique within this agent community name and the management stations within that community are provided with and must employ the community name in all get operations The agent may establish a number of communities with overlapping management station membership No Community Access Valid 1 public Read private Write Read Remote Management SNMP UPnP Read DDNS o o Read y O a SNMP Trap In the
38. Da ariza b ter 10178751 asta IDpricna BRC Clem IO Cention ferret pie Eihecnat Address O0 ithe 00 2006 snarled ka 4 Your new settings are shown on the TCP IP tab Verify that your IP Address is now 192 168 2 xxx your Subnet Mask is 255 255 255 0 and your Default Gateway is 192 168 2 1 These values confirm that your SAGEM F st 1500 ADSL Router is functioning 5 Close the Network window Now your computer is configured to connect to the SAGEM F st 1500 ADSL Router Disable HTTP Proxy You need to verify that the HTTP Proxy feature of your web browser is disabled This is so that your browser can view the SAGEM F st 1500 ADSL Router s HTML configuration pages The following steps are for Internet Explorer Internet Explorer 1 Open Internet Explorer and click the Stop button Click Explorer Preferences F i File Edit View G 8 About Inernet Explorer License Agreement Prerera nites Serices E 7 Hide Explore a a Hide Others aH Quit Explorer mo 2 Inthe Internet Explorer Preferences window under Network select Proxies 3 Uncheck all check boxes and click OK SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 3 21 3 Configuring Client Computer 38 0 Internet Explorer Preferences Security If you are accessing the Internet from a private network you can set gateways to allow Intem
39. Disable WIRELESS NAT Access Control MAC Filter URL Blocking Schedule Rule Intrusion Detection ADVANCED Network attacks that deny access to a network device are called Denial of Service DoS attacks DoS attacks are aimed at devices and networks with a connection to the Internet Their goal is not to steal information but to disable a device or network so users no longer have access to network resources The SAGEM F st 1500 ADSL Router protects against the following DoS attacks IP Spoofing Land Attack Ping of Death IP with zero length Smurf Attack UDP port loopback Snork Attack TCP null scan and TCP SYN flooding See section 4 8 5 for details The firewall does not significantly affect system performance so we advise leaving it enabled to protect your network Select Enable and click the Apply to open the Firewall submenus In this menu is included the following sub menus gt Access Control see section 4 8 1 MAC Filter see section 4 8 2 URL Blocking see section 4 8 3 Schedule Rule see section 4 8 4 Intrusion Detection see section 4 8 5 DMZ see section 4 8 6 Yv Y VV WV SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 37 4 Configuring the SAGEM F st 1500 ADSL router 4 8 1 Access Control Access Control allows users to define the outgoing traffic permitted or not
40. L transmission gt a subscription to a service provider for the Internet connection gt terminals with a TCP IP protocol stack e an Ethernet 10BASE T or 10 100BASE T interface or e awireless interface IEEE 802 11b g and for the SAGEM F st 1500 s HTTP HTML configuration gt aWEB browser Internet Explorer version 5 or above gt amonitor with a minimum resolution of 1024 x 728 pixels Before installing the SAGEM F st 1500 router we would advise you to L uninstall any other modem or ADSL router SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 1 5 1 Introduction SAGEM F st 1500 Reference Manual 288053220 04 Page 1 6 Reproduction and communication prohibited without the written permission of SAGEM SA 2 Description and Physical installation This chapter covers gt a description of the SAGEM F st 1500 Section 2 1 gt how to install the SAGEM F st 1500 Section 2 2 gt how to connect the ports of the SAGEM F st 1500 Section 2 3 gt how to power up the SAGEM F st 1500 Section 2 4 SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 2 1 2 Description and physical installation 2 1 Before installing the SAGEM F st 1500 ADSL Router verify that you have all the items listed under the Package Contents
41. MZ ROUTE Qos ADVANCED Add Schedule Rule Follow these steps to add a schedule rule 1 Click Add Schedule Rule 2 Define the appropriate settings for a schedule rule as shown in this example 3 Click OK and then click SAVE SETTINGS to save your settings Ssacem GE STATUS SETUP WIZARD SYSTEM WAN LAN WIRELESS NAT FIREWALL Access Control MAC Filter URL Blocking Schedule Rule Intrusion Detection DMZ ROUTE Qos ADVANCED SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 42 Edit Schedule Rule Name Comment Activate Time Period Week Day Every Day Sunday Monday Tuesday Wednesday Thursday Friday Saturday Start Time hh mm Save and Reboot Reset Logout End Time hh mm 4 Configuring the SAGEM F st 1500 ADSL router 4 8 5 Intrusion Detection 1 Intrusion Detection Feature Stateful Packet Inspection SPI and Anti DoS firewall protection Default Enabled The Intrusion Detection Feature of the SAGEM F st 1500 ADSL Router limits access for incoming traffic at the WAN port When the SPI feature is turned on all incoming packets will be blocked except for those types marked in the Stateful Packet Inspection section RIP Defect Default Enabled If an RIP request packet is
42. S allows users to map a static Domain Name to Dynamic IP address Dynamic DNS is a service to allow users anywhere on the Internet to find your website s and or mail server s with their constantly changing IP address STATUS DDNS Dynamic DNS Settings SETUP WIZARD lovsTEM DDNS allows users to map a static Domain Name to a dynamic IP address However You must get an account password and your static Domain Name from a DDNS service provider This router supports DDNS services from WAN www dyndns org and www tzo com ILAN WIRELESS Dynamic DNS Enable Disable NAT FIREWALL ROUTE Domain Name Qos ADVANCED ls ADSL Password Key Remote Management SNMP UPnP DDNS Provider DynDNs org Account E mail With DDNS enabled you can host your own website email server FTP site and more at your own location even if you have a dynamic IP address Select Enable or Disable to respectively activate or disactivate DDNS Dynamic DNS scroll down to support DDNS services from www DynDNS org and www TZO com SAGEM F st 1500 Reference Manual 288053220 04 Page 4 62 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 12 Finding the MAC address of a Network Card Windows 98 ME Click Start Run Type winipcfg and press ENTER The MAC address Is in the Adapter Address section Win
43. SAGEM F st 1500 SAGEM F st 1500WG Reference Manual 288 053 220 04 May 2005 Issue SAGEM SAGEM SA closely follows all technological changes and is continually striving to improve its products for the benefit of its customers It therefore reserves the right to change its documentation accordingly without notice All the trade marks mentioned in this guide are registered by their respective owners SAGEM F st is a registered trade mark of SAGEM sa Windows is a registered trade mark of Microsoft Corporation Internet Explorer is a registered trade mark of Microsoft Corporation Warning Warning icon used in this guide Information icon used in this guide Contents Pages Contents 0 1 to 0 4 1 Introduction 1 1 1 1About the SAGEM F st 1500WG ADSL Router 1 2 1 2Features and Benefits 1 2 1 3Applications 1 2 1 4Composition of the supply 1 4 1 5Prerequisites 1 5 2 Description and Physical installation 2 1 2 1Hardware Description 2 2 2 1 1 Front panel 2 3 2 1 2 Rear panel 2 4 2 2Physical Installation 2 5 2 2 1 Installation instructions 2 5 2 2 2 Desktop Installation 2 6 2 3Settings and Connecting 2 7 2 3 1 ISP settings 2 2 3 2 Install the SAGEM F st 1500 ADSL Router 27 2 3 3 Connect the ADSL Line 2 2 3 4 Phone Line Configuration 2 8 2 3 5 Attach to Your Network Using Ethernet Cabling 2 10 2 3 6 Connect the Power Adapter 2 10 2 4Powering up the SAGEM F st 1500 ADSL router 2 11 3 Co
44. SAGEM F st 1500 ADSL router 4 5 2 DNS Domain Name Servers DNS are used to map a domain name g www sagem com with the IP address e g 212 234 211 50 Your ISP should provide the IP address of one or more Domain Name Servers Enter those addresses on this page and click Apply STATUS DNS SETUP WIZARD Domain Name Server DNS is an index of IP addresses and Web addresses If you type a Web address into your browser such as www sagem com a DNS server will find that name in its index and find the matching IP address xxx xxx XXX Xxx Most ISPs provide a DNS server for speed and convenience Since your Service Provider may connect to the Internet with dynamic IP settings it is likely that the DNS server IP s are also provided dynamically However if there is a DNS server that you would rather use you need to specify the IP address here Domain Name Server DNS Address Secondary DNS Address optional SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 23 4 Configuring the SAGEM F st 1500 ADSL router 4 6 Wireless The SAGEM F st 1500 ADSL Router also operates as a wireless access point allowing wireless computers to communicate with each other To configure this function all you need to do is enable the wireless function define the radio channel the domain identifier and the security options Check E
45. Save and Reboot Reset Logout STATUS Access Control Add PC SETUP WIZARD SYSTEM WAN LAN WIRELESS NAT FIREWALL Access Control MAC Filter URL Blocking Schedule Rule Intrusion Detection DMZ ROUTE Qos ADVANCED Reproduction and communication prohibited without the written permission of SAGEM SA This page allows users to define service limitations of client PCs including IP address service type and scheduling rule criteria For the URL blocking function you need to configure the URL address first on the URL Blocking Site page For the scheduling function you also need to configure the schedule rule first on the Schedule Rule page Client PC Description Client PC IP Addre Client PC Service Service Name VA WW with URL Blocking E mail Sending News Forums E mail Receiving Secure HTTP File Transfer Telnet Service AIM NetMeeting DNS SNMP VPN PPTP VPN L2TP TCP UDP User Define Service Protocol OTCP UDP s Detail Description HTTP TCP Port 80 3128 8000 8001 8080 HTTP Ref URL Blocking Site Page SMTP TCP Port 25 NNTP TCP Port 119 POP3 TCP Port 110 HTTPS TCP Port 443 FTP TCP Port 21 TCP Port 23 AOL Instant Messenger TCP Port 5190 H 323 TCP Port 1720 1503 UDP Port 53 UDP Port 161 162 TCP Port 1723 UDP Port 1701 All TCP Port All UDP Port Blocking O O Q O O O Q O E Q O O C O
46. TE gos ADVANCED WAN C Status LAN Wireless 1 DOWN CC Protocol Username Public IP 8 35 C MUX PPPoA IP Address Subnet Mask DHCP Server Wireless Channel UPnP 192 168 2 1 255 255 255 0 Enabled Enabled 6 Enabled Additional information Runtime Code Yersion Boot Code Yersion ADSL Modem Code Yersion Serial Num Hardware Yersion LAN MAC Address Wireless MAC Address WAN MAC Address Numbers of DHCP Clients Security Log 08 01 2003 08 01 2003 08 01 2003 08 01 2003 08 01 2003 08 01 2003 08 01 2003 08 01 2003 08 01 2003 Save Clear DHCP Client Log sending sending sending sending sending sending sending sending sending F st 1500WG Ver 2 08 d Jan 28 2005 12 07 45 0 62 03 00 14 2474 4413034036 O1 00 60 4C 34 30 00 00 60 4C 34 30 02 00 60 4C 34 30 01 1 ACK tor192 266 2 OFFER to 192 166 2 ACK to 192 166 2 OFFER to 192 166 2 ACK to 192 166 2 OFFER to 192 166 2 ACK to 192 166 24 OFFER to 192 168 2 OFFER to 192 168 2 ip 192 168 2 4 mac O0 O8 EB 88 C3 68B5 name P1198342 SAGEM F st 1500 Reference Manual 288053220 04 Page 4 6 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router The following items are included on the Status page Item Description Displays ADSL link parameters and connection status Displays your VC settings and its status
47. address that you supplied to your ISP WAN Interface MAC Address Use the Gateway s default MAC address 00 60 4C 3A 30 01 Use this PC s MAC address 00 08 07 25 AB 6B Enter a new MAC address manually oo fos jc 25 AB eB SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 19 4 Configuring the SAGEM F st 1500 ADSL router 4 5 LAN Use the LAN menu to e define the port based VLAN belonging of the physical ports ie VLAN Binding e configure the LAN IP address and to enable the DHCP server for dynamic client address allocation STATUS SETUP WIZARD WIRELESS NAT FIREWALL ROUTE Qos ADVANCED LAN You can enable DHCP to dynamically allocate IP addresses to your client PCs or configure filtering functions based on specific clients or protocols The router must have an IP address for the local network VLAN Binding is to define the port based VLAN belonging of the physical ports Each physical port can be assigned to any configured VLAN profile LAN IP VLAN Binding IP Address Pool IP Address IP Subnet Mask DHCP Server Lease Time Start IP End IP Domain Name 192 168 2 1 255 255 255 0 Enabled Disabled Default v Default Default v Default Default Two Days v 192 168 2 2 192 168 2 254 Help Apply Cancel Paramet
48. affic Mapping l Traffic Statistics Rule Name Enter a Rule Name Traffic Type Select FTP VoIP E MAIL SNMP TELNET WWW VPN User define TCP User define UDP or User define IP Map to forwarding Select Forwarding Service from th lowest to the highest BE Best Effort AF1x Group Assured Forwarding AF2x AF3x AF4x or EF Expedited Forwarding Remark DSCP Check the box to change the DSCP Differenciated Service Code Point field in the IP header of each outgoing frame Direct to VC Select By routing or VCx SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 53 4 Configuring the SAGEM F st 1500 ADSL router e Click on the PER ESP AB EIA button the following screen appears 3X LZ Ssacem EE Home Save and Reboot Reset Logout STATUS Edit Traffic Class SETUP WIZARD This page is for user to specify a classify rule First define the class by the traffic type and the local and remote SYSTEM addresses Then set the Diffserv forwarding group this class is mapped to Finally select the outgoing YC that traffic of this class would be routed to WAN LAN WIRELESS NAT EEE Local Address Prange FIREWALL ROUTE 192 H168 f2 H a Qos Remote Address Any v Traffic Mapping Rule Name ftp Traffic Type FTP vi Traffic Statistics ADVANCED mopio P sbih BE v Remark
49. al Area Connection Status d x General Support Connector Statys Connected Duration 00 23 03 Speed 100 0 Mbps Activity Sent AY Recenved 4405 1 388 Close SAGEM F st 1500 Reference Manual 288053220 04 Page 3 16 Reproduction and communication prohibited without the written permission of SAGEM SA 3 Configuring Client Computer 5 Double click Internet Protocol TCP IP Internet Protocol 1CP IP Properties General Altermate Configuration ou can get IF settings assigned automatically if your network supports this capability Uthenwse you need to ask your network administrator for the appropriate IP settings Obtain ONS server address automatically O Use the following DNS server addresses fo 6 If Obtain an IP address automatically and Obtain DNS server address automatically are already selected your computer is already configured for DHCP If not select this option Disable HTTP Proxy You need to verify that the HTTP Proxy feature of your web browser is disabled This is so that your browser can view the SAGEM F st 1500 ADSL Routers HTML configuration pages refer to Internet Explorer on 3 2 1 SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 3 17 3 Configuring Client Computer Obtain IP Settings from Sagem F st1500 ADSL Router Now that you have configure
50. atistics see section 4 10 2 SAGEM F st 1500 Reference Manual 288053220 04 Page 4 52 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 10 1 Traffic Mapping In the QoS menu select Traffic Mapping the following screen appears 3 k sacem Ei ei ea S ann Home Save and Reboot Reset Logout STATUS SETUP WIZARD Traffic Mapping SYSTEM Up to 16 rules can be defined to classify traffic into Diffserv forwarding groups and WAN outgoing VCs LAN Rule WIRELESS Dee NAT FIREWALL ROUTE Qos Traffic Mapping Traffic Statistics ADVANCED Map to Outgoing Diffserv C No Traffic Mapping was defined all traffic is mapped to BE Traffic Description Configure No traffic Mapping was defined Add trafic class e Click on the button to add a traffic class the following screen appears Ssaccem EE Save and Reboot Reset Logout STATUS Edit Traffic Class SETUP WIZARD This page is for user to specify a classify rule First define the class by the traffic type and the local and remote SYSTEM addresses Then set the Diffserv forwarding group this class is mapped to Finally select the outgoing YC that traffic of this class would be routed to WAN LAN NAT Traffic Type Any J FIREWALL ROUTE Map to Forwarding BE N Group Remark DSCP Qos Direct to YC By Routing Tr
51. b menus gt VLAN see section 4 5 1 gt DNS see section 4 5 2 4 5 1 VLAN The VLAN menu allows the users to create a new VLAN entry and to configure its profile parameters To create a new VLAN profile simply click the Add VLAN hyperlink The Edit and Delete buttons at the end of each VLAN profile entry allow users to modify and delete the specific VLAN profile respectively Note that there is no Delete button for the default VLAN profile that cannot be deleted erates VLAN Profile SETUP WIZARD SYSTEM VLANs are organized and controlled by VLAN Profiles Up to S VLAN profiles can be created Once a VLAN profile is created it is empty and user should add interfaces into the YLAN by changing the VLAN setting of that WAN interface Please note that only those interfaces of IEEE 802 bridging type ex LAN ports and 1483 Bridging PYCs can be added to a VLAN LAN VLAN DNS WIRELESS No VLAN Grouped Interfaces Configure NAT 1 Default LAN1 LAN2 LAN3 LAN4 WLAN FIREWALL ROUTE Add VLAN Qos ADVANCED YLAN Table up to 5 rules The default VLAN is created per default and mapped to all LAN and WLAN ports SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 21 4 Configuring the SAGEM F st 1500 ADSL router Edit Click on the Edit button in the configure field allows to display VLAN profile and modify it
52. bited without the written permission of SAGEM SA Page 4 35 4 Configuring the SAGEM F st 1500 ADSL router 4 7 4 NAT Mapping Table S sacem FIPS Home Reset Logout STATUS NAT Mapping Table SETUP WIZARD SYSTEM NAT Mapping Table displays the current NAPT address mappings Index Protocol Local IP Local Port Pseudo IP Pseudo Port Peer IP Peer Port LAN WIRELESS NAT Address Mapping Virtual Server Special Application NAT Mapping Table FIREWALL ROUTE Qos ADVANCED SAGEM F st 1500 Reference Manual 288053220 04 Page 4 36 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 8 Firewall The SAGEM F st 1500 ADSL Router s firewall inspects packets at the application layer maintains TCP and UDP session information including time outs and the number of active sessions and provides the ability to detect and prevent certain types of network attacks Ssacem GE Home Save and Reboot Reset Logout STATUS FIREWALL SETUP WIZARD SYSTEM The Device provides extensive firewall protection by restricting connection parameters to limit the risk of hacker attack and defending against a wide array of common attacks However for applications that require unrestricted access to the Internet you can configure a specific client server as a demilitarized zone DMZ Enable or disable Firewall features Enable
53. configuration This chapter covers gt the default user name and password for HTTP access Section E 1 gt the default language for HTTP User Interface Section E 2 gt the default configuration on the local area network side Section E 3 gt the default configuration on the wide area network side Section E 4 gt the default configuration for advanced functions Section E 5 SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page E 1 Appendix E Default configuration SAGEM F st 1500 is set to Router mode by default These default settings can be modified by a special pre configuration of the SAGEM F st 1500 This can be performed through CLI Telnet default commands This section gives the default factory settings for the SAGEM F st 1500 The E 1 Default user name and password for HTTP access E 2 Default language for HTTP User Interface Language used to display HTTP pages English E 3 Default configuration on the local area network side characteristics WLAN Keys 64 bits Hex Key1 01 01 01 01 01 SAGEM F st 1500 Reference Manual 288053220 04 Page E 2 Reproduction and communication prohibited without the written permission of SAGEM SA Appendix E Default configuration E 4 Default configuration on the wide area network side vo C UBR QoS Class PCR 4000 cells s SCR 4000 cells s MBS 10
54. connect to this access point 4 Access control SSID SAGEM SSID Broadcast ENABLE DISABLE Wireless Mode Mixed 11b 11g Channel 13 j You must specify a common radio channel and SSID Service Set ID to be used by the SAGEM F st 1500 ADSL Router and all of its wireless clients Be sure you configure all of its clients to the same values Extended Service Set ID The ESSID must be the same on the SAGEM F st 1500 ADSL Router and all of its wireless clients ESSID Broadcast Enable or disable the broadcasting of the SSID Wireless Mode This device supports both 802 11g and 802 11b wireless networks Make your selection depending on the type of wireless network that you have Channel The radio channel used by the wireless router and its clients to communicate with each other This channel number must be the same on the ADSL Router and all of its wireless clients SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 9 4 Configuring the SAGEM F st 1500 ADSL router 4 2 3 WEP To make your wireless network safe you should turn on the security function Sw k S SAGEM E Home Reset Logout 1 PPP settings 3 WEP 2 Channel and SSID WEP is the basic mechanism to transmit your data securely over the wireless network Matching encryption keys must be setup on your router and wireless client devices to
55. curity prevent an Internet application from functioning correctly e Security The SAGEM F st 1500WG ADSL Router supports security features that deny Internet access to specified users or filter all requests for specific services that the administrator does not want to serve The SAGEM F st 1500WG ADSL Router s firewall also blocks common hacker attacks including IP Spoofing Land Attack Ping of Death IP with zero length Smurf Attack UDP port loopback Snork Attack TCP null scan and TCP SYN flooding WEP Wired Equivalent Privacy SSID and MAC filtering provide security over the wireless network e Virtual Private Network VPN The SAGEM F st 1500WG ADSL Router supports three of the most commonly used VPN protocols PPTP L2TP and IPSec These protocols allow remote users to establish a secure connection to their corporate network If your service provider supports VPNs then these protocols can be used to create an authenticated and encrypted tunnel for passing secure data over the Internet i e a traditionally shared data network The VPN protocols supported by the SAGEM F st 1500WG ADSL Router are briefly described below e Point to Point Tunneling Protocol Provides a secure tunnel for remote client access to a PPTP security gateway PPTP includes provisions for call origination and flow control required by ISPs e L2TP merges the best features of PPTP and L2F Like PPTP L2TP requires that the ISP s route
56. d your computer to connect to your SAGEM F st 1500 ADSL Router it needs to obtain new network settings By releasing old DHCP IP settings and renewing them with settings from SAGEM F st 1500 ADSL Router you can verify that you have configured your computer correctly 1 On the Windows desktop click Start All Programs Accessories Command Prompt f Accessibilit 9 MSN Explorer a Windows Update 2 P Communications i Cg Ee ee Windows Media Plae Dak iaa F Entertainment 7 C Games P System Tools LF iD Windows Movie Make m Internet Explorer f QO Address Book Fea l Startup Calculator Tour Windows F i x Internet Explorer in Command Prompt go Files and Settings Tr WA MSN Explorer L Notepad STD Wizard a La Outlook Express Paint Ww Paint ea J Program Compatibility Wizard l a amp Windows Media Player Synchronize All Programs windows Messenger Tour Windows P Log CFF 0 Turn Windows Explorer g windows Movie Maker 3 S o WordPad 2 o Command Prompt G 5 Documents and Settings sagem ipconf igre lease Mindows IP Configuration Ethernet adapter Local Area Connection Connection specific DHS Suffix IP Address 2 2 ew ew ew ee ee E Subnet Mask z Default Gateway C Documents and Settings sagem gt SAGEM F st 1500 Reference Manual 288053220 04 Page 3 18 Reproduction and communication prohibited without the writ
57. different application types that are using dynamic port numbers For the applications checked in the list below the Device will support full operation as initiated LAN from the local LAN WIRELESS The Device firewall can block common hacker attacks including IP Spoofing Land Attack Ping of Death IP NAT with zero length Smurf Attack UDP port loopback Snork Attack TCP null scan and TCP SYN flooding FIREWALL Intrusion Detection Feature Access Control MAC Filter SPI and Anti DoS firewall protection Iv URL Blocking IP defect E e ae Discard Ping To WAN m DMZ e Stateful Packet Inspection ROUTE Qos Packet Fragmentation Iv ADVANCED TCP Connection Iv UDP Session Vv FTP Service Iv H 323 Service TFTP Service e When hackers attempt to enter your network we can alert you by e mail Your E mail Address SMTP Server Address POP3 Server Address User name Password e Connection Policy Fragmentation half open wait ho secs TCP SYN wait fo sec TCP FIN wait 5 sec TCP connection idle timeout 3600 sec UDP session idle timeout fo sec H 323 data channel idle timeout fiso sec e DoS Detect Criteria Total incomplete TCP UDP sessions HIGH 300 session Total incomplete TCP UDP sessions LOW 250 session Incomplete TCP UDP sessions per min HIGH 250 session Incomplete TCP UDP sessions per min LOW 200 session i Maximum incomplete TCP UDP ses
58. dow select the Protocols tab Double click TCP IP Protocol 4 When the Microsoft TCP IP Properties window open select the IP Address tab 5 Inthe Adapter drop down list be sure your Ethernet adapter is selected 6 If Obtain an IP address automatically is already selected your computer is already configured for DHCP If not select this option and click Apply 7 Click the DNS tab to see the primary and secondary DNS servers Record these values and then click Remove Click Apply and then OK Network Ei Ea Identification Serice Piotocoals adapters Bindings Network Protocols Y NetBEU CPP Protoce Microsoft TCP ZIP Properties IPAddiess DNS WINS Address Routing An lF address can be automaticaly assigned to this network card by by a DHCP server If pour network does not have a OHCF server ask your network administrator tor an address and then type itir Deze the space below Tran area diver blan anif address from a OHCP server C Specify an IP addres Rediess l SPUD Mesk l Drath kacma Adwanced SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 3 9 3 Configuring Client Computer Microsoft TCP IP Properties IP Adcress DNS WINS Addresa Routing Domain Mane System DNS Host Mame D omari QEMCOHPUTERF DAS Sorica Sears
59. dows NT4 2000 XP Click Start Programs Command Prompt Type ipconfig all and press ENTER The MAC address is listed as the Physical Address Macintosh Click System Preferences Network The MAC address is listed as the Ethernet Address on the TCP IP tab Linux Run the command sbin ifconfig The MAC address is the value after the word HWaddr SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 63 4 Configuring the SAGEM F st 1500 ADSL router SAGEM F st 1500 Reference Manual 288053220 04 Page 4 64 Reproduction and communication prohibited without the written permission of SAGEM SA A Appendix A Troubleshooting SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page A 1 Appendix A Troubleshooting This section describes common problems you may encounter and possible solutions to them The SAGEM F st 1500 ADSL Router can be easily monitored through panel indicators to identify problems Troubleshooting Chart Symptom LED Indicators The PWR LED is Off e Check connections between the SAGEM F st 1500 ADSL Router the external power supply and the wall outlet e If the power indicator does not turn on when the power cord is plugged in you may have a problem with the power outlet power cord or exter
60. e pinging has been configured for TCP IP Management Problems The user cannot connect e Be sure to have configured the SAGEM F st 1500 ADSL Router with a using the web browser _ valid IP address subnet mask and default gateway e Check that you have a valid network connection to the SAGEM F st 1500 ADSL Router and that the port you are using has not been disabled e Check the network cabling between the management station and the SAGEM F st 1500 ADSL Router The user forgot or lost the e Press the Reset button on the rear panel holding it down for at least five seconds to restore the factory defaults SAGEM F st 1500 Reference Manual 288053220 04 Page A 2 Reproduction and communication prohibited without the written permission of SAGEM SA Appendix A Troubleshooting Troubleshooting Chart LED Indicators Wireless Problems A wireless PC cannot associate with the ADSL Router The wireless network is often interrupted The SAGEM F st 1500 ADSL Router cannot be detected by a wireless client e Make sure the wireless PC has the same SSID settings as the SAGEM F st 1500 ADSL Router See Channel and SSID on section 4 6 1 e You need to have the same security settings on the clients and the SAGEM F st 1500 ADSL Router See Security on section 4 6 3 e Move your wireless PC closer to the SAGEM F st 1500 ADSL Router to find a better signal If the signal is still weak chang
61. e the angle of the antenna e There may be interference possibly caused by a microwave ovens or wireless phones Change the location of the interference sources or of the ADSL Router e Change the wireless channel on the SAGEM F st 1500 ADSL Router See Channel and SSID on section 4 6 1 e Check that the antenna connectors and cabling are firmly connected The distance between the SAGEM F st 1500 ADSL Router and wireless PC is too great e Make sure the wireless PC has the same SSID and security settings as the SAGEM F st 1500 ADSL Router See ADSL Router See Channel and SSID on section 4 6 1 and Security on section 4 6 3 SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page A 3 Appendix A Troubleshooting SAGEM F st 1500 Reference Manual 288053220 04 Page A 4 Reproduction and communication prohibited without the written permission of SAGEM SA B Appendix B Safety warnings This chapter covers gt Safety warnings Section B 1 gt CE declaration of conformity Section B 2 SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page B 1 Appendix B Safety warnings B 1 Safety warnings The SAGEM F st 1500 product is compliant with EN 60950 April 2002 edition The safety levels in the sense of this standard
62. e via web based management Web based management configuration Power indicators Event and history logging Network ping Security Features Password protected configuration access User authentication PAP CHAP with PP Firewall NAT NAPT VPN pass through IPSec ESP Tunnel mode L2TP PPTP LAN Features IEEE 802 1d self learning transparent Bridging DHCP Server DNS Proxy Static Routing RIPv1 and RIP Dynamic DNS VLAN binding SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page D 3 Appendix D Technical specifications QoS Features Diffserv RFC 2475 Diffserv PHBs BE AF1x AF1x AF1x AF1x and EF Diffserv code point DSC remarking Layer 2 3 Multi field Classification Application Layer Classification Voice Over IP Features SIP Passthrough RFC 3261 Applications Netmeeting ICQ Real Player QuickTime DialPad PC Anywhere Telnet SNTP NNTP D 4 Radio Features Wireless RF module Frequency Band 802 11g Radio 2 4GHz 802 11b Radio 2 4GHz USA FCC 2412 to 2462 MHz Ch1 to Ch11 Canada IC 2412 to 2462 MHz Ch1 to Ch11 Europe ETSI 2412 to 2472 MHz Ch1 to Ch13 Spain 2457 to 2462 MHz Ch10 et Ch11 France 2457 to 2472 MHz Ch10 to Ch13 Japan STD T66 STD 33 2412 to 2484 MHz Ch1 to Ch14 Modulation Type OFDM CCK SAGEM F st 1500 Reference Manual 2880532
63. ect the default key from the drop down menu Click Apply gt The passphrase can consist of up to 32 alphanumeric characters To manually L configure the encryption key enter five hexadecimal pairs of digits for each 64 bit key or enter 13 pairs for the single 128 bit key A hexadecimal digit is a number or letter in the range 0 9 or A F Note that WEP protects data transmitted between wireless nodes but does not protect any transmissions over your wired network or over the InternetSAGEM st 1500 ADSL Router using Internet Explorer 5 0 or above SAGEM F st 1500 Reference Manual 288053220 04 Page 4 28 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 46 5 WPA Wi Fi Protected Access WPA combines Temporal Key Integrity Protocol TKIP and 802 1x mechanisms It provides dynamic key encryption and 802 1x authentication service Ssacem FE STATUS SETUP WIZARD SYSTEM WAN LAN WIRELESS Channel and SSID Access control WPA Cypher suite Authentication Pre shared key type Pre shared Key Group Key Re_Keying FIREWALL ROUTE Qos ADVANCED Parameter Cypher suite Authentication Home Save and Reboot Reset Logout WPA is a security enhancement that strongly increases the level of data protection and access control for existing wireless LAN Matching authentication and encryption methods must be setup o
64. en permission of SAGEM SA 2 Description and physical installation 2 1 1 Front panel PWR ADSL WLAN ALM ETHERNET te Ve lt S SAGEM Figure 2 1 Front Panel From left to right this comprises eight green supervisory LEDs followed by the SAGEM logo the meaning of which is given in the table below seo famus fooson O The SAGEM F st 1500 ADSL Router is receiving power Normal operation Power off or failure ADSL ADSL connection is functioning correctly Flashing The SAGEM F st 1500 ADSL Router is establishing an ADSL link ADSL connection is not established ALM PPP is not established Off PPP has been established 4 LEDs SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 2 3 2 Description and physical installation 2 1 2 Rear panel LAN Ports ADSL Port Antenna Power Inlet Power button Figure 2 2 Rear Panel ADSL WAN port RJ 11 Connect your ADSL line to this port Connect the included power adapter to this inlet Warning Using the wrong type of power adapter may damage the SAGEM F st 1500 ADSL Router Use this button to reset the power and restore the default factory settings To reset without losing configuration settings see Reset on chapter 4 Fast Ethernet ports RJ 45 Connect devices on your local area network to these ports i e a PC hub or switch Di
65. er Description IP Address The IP address of the SAGEM F st 1500 ADSL Router IP Subnet Mask The subnet mask of the network DHCP Server The SAGEM F st 1500 ADSL Router comes with the DHCP function To dynamically assign an IP address to client PCs enable this function VLAN Binding AN1 to LAN4 WLAN Each LAN or Wireless LAN port can be bound to any configured VLAN profile Per default the LAN and WLAN ports are bound to a default VLAN Lease Time Set the IP lease time For home networks this may be set to Forever which means there is no time limit on the IP address lease SAGEM F st 1500 Reference Manual 288053220 04 Page 4 20 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router IP Address Pool Start IP Specify the start IP address of the DHCP pool Do not include the gateway address of the SAGEM F st 1500 ADSL Router in the client address pool If you change the pool range make sure the first three octets match the gateway s IP address i e 192 168 2 xxx PE nd IP Specify the end IP address of the DHCP pool If your network uses a domain name enter it here Otherwise leave this field blank Modify all parameters on the screen then click on Apply a Remember to configure your client PCs for dynamic address allocation See section L 3 1 for details In this menu is included the following su
66. eriod Quiet Period Server Type RADIUS Server Parameters Server IP Server Port Secret Key NAS ID OEnable Disable 300 Seconds 0 for no timeout checking 300 Seconds 0 for no re authentication 60 Seconds after authentication failed RADIUS v SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 30 4 Configuring the SAGEM F st 1500 ADSL router 802 1X 802 1X Enable or disable this authentication function Authentication Session Idle timeout Defines a maximum period of time for which the connection is maintained during inactivity Re Authentication Defines a maximum period of time for which the Period authentication server will dynamically re assign a session key to a connected client Quiet Period Defines a maximum period of time for which the SAGEM F st 1500 ADSL Router will wait between failed authentications Server Type Select TINY or RADIUS as the authentication server RADIUS Server Parameters Server IP The IP address of your authentication server The port used for the authentication service Secret Key The secret key shared between the authentication server and its clients NAS ID Defines the request identifier of the Network Access Server TINY Server Users The Tiny Encryption Algorithm is used to encrypt the Profile up to 10 pass
67. et access Contact your network manager Security Zones for more information Note These settings are shared with other Ratings applications through Internet Config Use Proxy Servers a Web Prony Settings Advanced y Foma AutoFill Use Web Proxy for all _ Bypass Web Proxy for FTP Forms AutoComplete AutoFill Profile Y Receiving Fibes Download Options File Helpers Cookies 3 Network Secure Proxy SHthings E Mall Proxy a can Gopher Proxy Setting sic List the sites you want to connect to directly bypassing the proxies a isa Helpers set above Puta space or comma between each site Q Proxies Site Passwords Ww E mail General SAGEM F st 1500 Reference Manual 288053220 04 Page 3 22 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router This chapter covers gt The SETUP WIZARD menu section 4 2 gt The ADVANCED menu Section 4 11 gt Finding the MAC address of a Network Card Section 4 12 SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 1 4 Configuring the SAGEM F st 1500 ADSL router P After you have configured TCP IP on a client computer you can configure the L SAGEM st 1500 ADSL Router using Internet Explorer 5 0 or above To access the SAGEM F st 1500
68. f SAGEM SA D Appendix D Technical specifications This chapter covers gt the Mechanical Characteristics Displays Section D 1 gt the Electrical Characteristics section D 2 gt the Soft Component Features Section D 3 gt the Radio Features Section D 4 gt the Environmental characteristics Section D 5 SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page D 1 Appendix D Technical specifications D 1 Mechanical Characteristics Displays Dimensions mm D 2 Electrical Characteristics ADSL Features Supports DMT line modulation Supports Annex A Full Rate ADSL up to 8 Mbps downstream up to 1 Mbps upstream G 992 1 amp 11 413 Issue 2 Supports G Lite ADSL up to 1 5 Mbps downstream up to 512 Kbps upstream Supports Annex A ADSL 2 up to 25 Mbps downstream up to 2 Mbps upstream G 992 5 Dying GASP support Input Power 12V 1A SAGEM F st 1500 Reference Manual 288053220 04 Page D 2 Reproduction and communication prohibited without the written permission of SAGEM SA Appendix D Technical specifications D 3 Soft Component Features ATM Features RFC1483 Encapsulation IP Bridging and encapsulated routing PPP over ATM LLC amp VC multiplexing RFC2364 Classical IP RFC1577 Traffic shaping UBR CBR OAM F4 F5 support PPP over Ethernet Client Management Features Firmware upgrad
69. f the power supply to the router The SAGEM F st 1500 is designed for connection to a TT or TN system power supply network The SAGEM F st 1500 is not designed for connection to an IT system electrical installation power supply with separate neutral Protection against short circuits and leaks between phase neutral and earth must be provided by the building s electrical installation The power circuit for this equipment must be fitted with 16 A overcurrent protection and differential protection The mains connection must be via a readily accessible switched wall socket Maintenance gt gt The casing must not be opened This must be done only by personnel qualified and approved by your supplier Do not use liquid or aerosol cleaning agents Never open the mains adapter block this can expose you to mortal danger SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 2 5 2 Description and physical installation 2 2 2 Desktop Installation gt place the SAGEM F st 1500 on its plastic stand fitted with four non slip rubber feet gt make sure that the various leads pass correctly through the cable guide to avoid any risk of tension or of dropping the unit SAGEM F st 1500 Reference Manual 288053220 04 Page 2 6 Reproduction and communication prohibited without the written permission of SAGEM SA 2 Description a
70. face SETUP WIZARD ATM1 Protocol PPPoA VPI YCI 8 435 Encapsulation VC MUX v QoS Class UBR PCR SCR MBS 4000 4000 10 IP assigned by ISP Yes xi IP Address 0 0 0 0 Subnet Mask 0 0 0 0 Clone MAC Address LAN WIRELESS NAT Username Connect Type Always Connected Idle Time Minute 20 FIREWALL Password ROUTE Confirm Password Qos ADVANCED MTU Protocol Disables the ATM mode e 1483 Bridging Bridging Bridging is a standardized layer 2 technology It is typically used in corporate networks to extend the physical reach of a single LAN segment and increase the number of stations on a LAN without compromising performance Bridged data is encapsulated using the RFC1483 protocol to enable data transport e PPPoA Point to Point over ATM e 1483 Routing Use 1483 Routing protocol e PPPoE Point to Point over Ethernet e MAC Encapsulated MAC Encapsulated Routing Routing VPI VCI Virtual Path Identifier VPI and Virtual Circuit Identifier VCI Each connection must have a unique pair of VPI VCI settings Encapsulation Specifies how to handle multiple protocols at the ATM transport layer e VC MUX Point to Point Protocol over ATM Virtual Circuit Multiplexer null encapsulation allows only one protocol running per virtual circuit with less overhead Point to Point Protocol over ATM Logical Link Control LLC allows multiple protocols running over one virtual circuit using sligh
71. iguring Client Computer 3 2 3 On Windows 2000 1 On the Windows desktop click Start Settings Network and Dial Up Connections 2 Click the icon that corresponds to the connection to your SAGEM F st 1500 ADSL Router 3 The connection status screen will open Click Properties Local Area Connection 1 Status x General Connection Status Connected Duration 00 15 12 Speed 10 0 Mbps Sent an HHeceived Ct Packets 49 0 Properties Disable Close SAGEM F st 1500 Reference Manual 288053220 04 Page 3 12 Reproduction and communication prohibited without the written permission of SAGEM SA 3 Configuring Client Computer 4 Double click Internet Protocol TCP IP Internet Protocol TCP IP Properties 2 a 3 x General fou can get IF settings assigned automatically if your network supports this capability Othenvise you need to ask your network administrator For the appropriate F settings f Use the following IP address IP address Subnet mask Default gateway f Obtain ONS server address automatically Use the following ONS server addresses Prefered OWS server Advanced men 5 If Obtain an IP address automatically and Obtain DNS server address automatically are already selected your computer is already configured for DHCP If not select this option Alternate WAS server Disable HTTP Pr
72. ion of SAGEM SA Page 4 49 4 Configuring the SAGEM F st 1500 ADSL router General RIP Parameters RIP mode Globally enables or disables RIP Auto summary If Auto summary is disabled then RIP packets will include sub network information from all subnetworks connected to the router If enabled this sub network information will be summarized to one piece of information covering all subnetworks Table of current Interface RIP parameter Operation Mode Disable RIP disabled on this interface e Enable RIP enabled on this interface e Silent Listens for route broadcasts and updates its route table It does not participate in sending route broadcasts Version Sets the RIP Routing Information Protocol version to use on this interface Poison Reverse A method for preventing loops that would cause endless retransmission of data traffic Authentication None No authentication Required e Password A password authentication key is included in the packet If this does not match what is expected the packet will be discarded This method provides very little security as it is possible to learn the authentication key by watching RIP packets e MD5 An algorithm that is used to verify data integrity through the creation of a 128 bit message digest from data input which may be a message of any length that is claimed to be as unique to that specific data as a fingerprint is to a specific individual Authentication
73. ions as described in the following table Parameter Defaults Description Fragmentation 10 sec Configures the number of seconds that a packet state structure half open wait remains active When the timeout value expires the router drops the unassembled packet freeing that structure for use by another packet TCP SYN wait 30 sec Defines how long the software will wait for a TCP session to synchronize before dropping the session TCP FIN wait 5 sec Specifies how long a TCP session will be maintained after the firewall detects a FIN packet TCP connection 3600 seconds The length of time for which a TCP session will be managed if there idle timeout 1 hour is no activity UDP session 30 sec The length of time for which a UDP session will be managed if idle timeout there is no activity H 323 data 180 sec The length of time for which an H 323 session will be managed if channel idle there is no activity timeout SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 45 4 Configuring the SAGEM F st 1500 ADSL router 5 DoS Criteria and Port Scan Criteria Set up DoS and port scan criteria in the spaces provided as shown below Note The firewall does not significantly affect system performance so we advise enabling the prevention features to protect your network Page 4 46 Parameter Total incomplete TCP UDP sessions HIGH To
74. l 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 3 1 3 Configuring Client Computer After completing hardware setup by connecting all your network devices you need to configure your computer to connect to the SAGEM F st M 4500 ADSL Router See PC Windows 98 Me on sub section 3 2 1 Windows NT 4 0 on sub section 3 2 2 Windows 2000 on sub section 3 2 3 Windows XP sub section 3 2 4 Mac Mac OS 10 2 on sub section 3 3 Configuring Your Macintosh Computer depending on your operating system 3 1 TCP IP Configuration To access the Internet through the SAGEM F st 1500 ADSL Router you must configure the network settings of the computers on your LAN to use the same IP subnet as the SAGEM F st 1500 ADSL Router The default IP settings for the SAGEM F st 1500 ADSL Router are IP Address 192 168 2 1 Subnet Mask 255 255 255 0 m These settings can be changed to fit your network requirements but you must first configure at least one computer to access the SAGEM F st 1500 ADSL Router s web configuration interface in order to make the required changes See Configuring the SAGEM F st 1500 ADSL Router on chapter 4 for instruction on configuring the SAGEM F st 1500 ADSL Router SAGEM F st 1500 Reference Manual 288053220 04 Page 3 2 Reproduction and communication prohibited without the written permission of SAGEM SA 3 Configuring Client Computer 3
75. list see 1 4 If any of the items are missing or damaged contact your local distributor Also be sure that you have all the necessary cabling before installing the SAGEM F st 1500 ADSL Router After installing the ADSL Router refer to Configuring the SAGEM F st 1500 ADSL Router on chapter 4 Hardware Description The SAGEM F st 1500 ADSL Router contains an integrated ADSL modem and connects to the Internet or to a remote site using its RJ 11 WAN port It can be connected directly to your PC or to a local area network using any of the four Fast Ethernet LAN ports Access speed to the Internet depends on your service type Full rate ADSL provides up to 8 Mbps downstream and 640 kbps upstream G lite or splitterless ADSL provides up to 1 5 Mbps downstream and 512 kbps upstream However you should note that the actual rate provided by specific service providers may vary dramatically from these upper limits Data passing between devices connected to your local area network can run at up to 100 Mbps over the Fast Ethernet ports and 54 Mbps over the built in wireless network adapter The SAGEM F st 1500 ADSL Router includes an LED display on the front panel for system power and port indications that simplifies installation and network troubleshooting It also provides the following ports on the rear panel SAGEM F st 1500 Reference Manual 288053220 04 Page 2 2 Reproduction and communication prohibited without the writt
76. n connecting to other network devices such as an Ethernet switch use the cable type shown in the following table Attached Device Port Type Connecting Cable Type MDI X Straight through SAGEM F st 1500 Reference Manual 288053220 04 Page C 2 Reproduction and communication prohibited without the written permission of SAGEM SA Appendix C Cables C 1 4 Pin Assignments General With 100BASE TX 10BASE T cable pins 1 and 2 are used for transmitting data and pins 3 and 6 for receiving data RJ45 Pin Assignments COR The and signs represent the polarity of the wires that make up each wire pair Straight Through Wiring If the port on the attached device has internal crossover wiring MDI X then use straight through cable Straight Through Cable Pin Assignments Crossover Wiring If the port on the attached device has straight through wiring MDI use crossover cable Crossover Cable Pin Assignments 1 Tx 1 Rx 2 3 SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page C 3 Appendix C Cables C 2 ADSL Cable Use standard telephone cable to connect the RJ 11 telephone wall outlet to the RJ 45 ADSL port on the Sagem F st1500 ADSL Router DO NOT plug a phone jack connector into any RJ 45 port C 2 1 Specifications Cable Types and Specifications ADSL Line Standard Telephone cable RJ11
77. n your router and wireless client devices to use WPA TKIP x 802 1x Pre shared Key Passphrase 8 63 characters O Hex 64 digits Seconds K Packets Per 86400 Oper 1000 O Disable The security mechanism used in WPA for encryption Choose 802 1X or Pre shared Key to use as the authentication method for the enterprise network with a RADIUS server ePre shared key for the SOHO network environment without an authentication server Pre shared key type Select the key type to be used in the Pre shared Key Pre shared Key Type in the key here Group Key Re Keying The period of renewing broadcast multicast key Reproduction and communication prohibited without the written permission of SAGEM SA SAGEM F st 1500 Reference Manual 288053220 04 Page 4 29 4 Configuring the SAGEM F st 1500 ADSL router 4 6 6 802 1X lf 802 1X is used in your network then you should enable this function for the SAGEM F st 1500 ADSL Router STATUS SETUP WIZARD SYSTEM WAN LAN WIRELESS Channel and Save and Reboot Reset Logout This page allows you to set the 802 1X a method for performing authentication to wireless connection These parameters are used for this access point to connect to the Authentication Server 802 1 Authentication SSID Session Idle Timeout Access control Security WEP gt WPA 802 1 NAT FIREWALL ROUTE Qos ADVANCED Re Authentication P
78. nable and click Apply S SAGEM 3 Home Save and Reboot Reset Logout STATUS WIRELESS SETUP WIZARD SYSTEM WAN LAN Enable or disable Wireless module function eEnable ODisable The gateway can be quickly configured as an wireless access point for roaming clients by setting the service set identifier SSID and channel number It also supports data encryption and client filtering WIRELESS Channel and SSID Access control FIREWALL ROUTE Qos ADVANCED In this menu is included the following sub menus gt Channel and SSID see section 4 6 1 Access control see section 4 6 2 Security see section 4 6 3 WEP see section 4 6 4 WPA setting see section 4 6 5 802 x see section 4 6 6 V VV V WV SAGEM F st 1500 Reference Manual 288053220 04 Page 4 24 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 6 1 Channel and SSID You must specify a common radio channel and SSID Service Set ID to be used by the SAGEM F st 1500 ADSL Router and all of its wireless clients Be sure you configure all of its clients to the same values Ssacem GE Home Save and Reboot Reset Logout STATUS Channel and SSID SETUP WIZARD SYSTEM WAN This page allows you to define SSID and Channel ID for wireless connection In the wireless environment the router can also act as an wireless access point These parame
79. nal power supply However if the unit powers off after running for a while check for loose power connections power losses or surges at the power outlet If you still cannot isolate the problem then the external power supply may be defective In this case contact Technical Support for assistance The ADSL LED is Off e Verify that the SAGEM F st 1500 ADSL Router and attached device are powered on e Be sure the cable is plugged into both the ADSL Router and the corresponding device e Verify that the proper cable type is used and that its length does not exceed the specified limits e Be sure that the network interface on the attached device is configured for the proper communication speed and duplex mode e Check the adapter on the attached device and cable connections for possible defects Replace any defective adapter or cable if necessary Network Connection Problems The user cannot ping the Verify that the IP addresses are properly configured For most applications SAGEM F st 1500 you should use the A DSL Router s DHCP function to dynamically assign IP ADSL Router from the addresses to hosts on the attached LAN However if you manually configure attached LAN IP addresses on the LAN verify that the same network address network component of the IP address and subnet mask are used for both the SAGEM F st 1500 ADSL Router and any attached LAN devices e Be sure the device you want to ping or from which you ar
80. nd physical installation 2 3 Settings and Connecting 2 3 1 ISP settings Please collect the following information from your ISP before setting up the SAGEM F st 1500 ADSL Router e ISP account user name and password e Protocol encapsulation and VPI VCI circuit numbers e DNS server address e P address subnet mask and default gateway for fixed IP users only 2 3 2 Install the SAGEM F st 1500 ADSL Router The SAGEM F st 1500 ADSL Router can be positioned at any convenient location in your office or home No special wiring or cooling requirements are needed You should however comply with the following guidelines e Keep the SAGEM F st 1500 ADSL Router away from any heating devices e Do not place the SAGEM F st 1500 ADSL Router in a dusty or wet environment You should also remember to turn off the power remove the power cord from the outlet and keep your hands dry when you install the SAGEM F st 1500 ADSL Router 2 3 3 Connect the ADSL Line Connect the supplied RJ 11 cable from the ADSL Microfilter Splitter to the ADSL port on your SAGEM F st 1500 Router When inserting an ADSL RJ 11 plug be sure the tab on the plug clicks into position to ensure that it is properly seated SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 2 7 2 Description and physical installation 2 3 4 Phone Line Configuration Ins
81. nfiguring Client Computer 3 1 3 1TCP IP Configuration 3 2 3 2Configuring your Windows computer 3 3 3 2 1 On Windows 98 Me 3 3 3 2 2 On Windows NT 4 0 3 8 3 2 3 On Windows 2000 3 12 3 2 4 On Windows XP 3 16 3 3Configuring your Mac computer 3 20 SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 0 1 4 Configuring the SAGEM F st 1500 ADSL router 4 1STATUS 4 2 SETUP WIZARD menu 4 2 1 PPP Setting 4 2 2 Channel and SSID 4 2 3 WEP 4 2 4 Access Control 4 3SYSTEM 4 3 1 Time Settings 4 3 2 Password Settings 4 3 3 Configuration tools 4 3 4 Firmware Upgrade 4 3 5 Reset 4 4 WAN menu 441 ATMPVC 44 2 Clone MAC 4 5LAN 4 5 1 VLAN 4 5 2 DNS 4 6Wireless 4 6 1 Channel and SSID 4 6 2 Access Control 4 6 3 Security 46 4 WEP 46 5 WPA 46 6 802 1X 4 7NAT 4 7 1 Address Mapping 4 7 2 Virtual Server 4 7 3 Special Application 4 7 4 NAT Mapping Table 4 8Firewall 4 8 1 Access Control 4 8 2 MAC Filter 4 8 3 URL Blocking 4 8 4 Schedule Rule 4 8 5 Intrusion Detection 48 6 DMZ 4 9Route 4 9 1 Static Route 4 9 2 RIP 4 9 3 Routing Table 4 10 QoS 4 10 1 Traffic Mapping 4 10 2 Traffic statistics SAGEM F st 1500 Reference Manual 288053220 04 Page 0 2 Reproduction and communication prohibited without the written permission of SAGEM SA 4 1 4 15 4 16 4 17 4 19 4 20 4 21 4 23 4 24 4 25 4 26 4 27 4 28 4 29 4 30 4 32 4 33 4 34 4
82. nication prohibited without the written permission of SAGEM SA 3 Configuring Client Computer 3 Type IPCONFIG RENEW and press the ENTER key Verify that your IP Address is now 192 168 2 xxx your Subnet Mask is 255 255 255 0 and your Default Gateway is 192 168 2 1 These values confirm that your SAGEM F st M 4500 ADSL Router is functioning c Command Prompt 3 O icrosoft Windows 2666 Version 5 06 2195 LC Copyright 1985 1999 Microsoft Corp C gt IPCONFIG RELEASE findows 2660 IP Configuration IP address successfully released For adapter Local Area Connection 1 Gs TPCONFIG RENEW Windows 2668 IP Configuration Ethernet adapter Local Area Connection 1 Connection specific DHS Suffix 192 168 subnet Mask s ss a E 299 299 Default Gateway i 172 168 4 Type EXIT and press the ENTER key to close the Command Prompt window Your computer is now configured to connect to the SAGEM F st 1500 ADSL Router SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 3 15 3 Configuring Client Computer 3 2 4 On Windows XP 1 On the Windows desktop click Start Control Panel 2 Inthe Control Panel window click Network and Internet Connections 3 The Network Connections window will open Double click the connection for this device 4 On the connection status screen click Properties Loc
83. not acknowledged to by the router it will stay in the input queue and not be released Accumulated packets could cause the input queue to fill causing severe problems for all protocols Enabling this feature prevents the packets from accumulating Discard Ping to WAN Default Disabled Prevent a ping on the ADSL Router s WAN port from being routed to the network 2 Stateful Packet Inspection This is called a stateful packet inspection because it examines the contents of the packet to determine the state of the communications i e it ensures that the stated destination computer has previously requested the current communication This is a way of ensuring that all communications are initiated by the recipient computer and are taking place only with sources that are known and trusted from previous interactions In addition to being more rigorous in their inspection of packets stateful inspection firewalls also close off ports until connection to the specific port is requested SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 43 4 Configuring the SAGEM F st 1500 ADSL router Ssacem i Home Save and Reboot Reset Logout STATUS SETUP WIZARD Intrusion Detection SYSTEM When the SPI Stateful Packet Inspection firewall feature is enabled all packets can be blocked Stateful WAN Packet Inspection SPI allows full support of
84. oduction and communication prohibited without the written permission of SAGEM SA Page 4 27 4 Configuring the SAGEM F st 1500 ADSL router 4 6 4 WEP lf you want to use WEP to protect your wireless network you need to set the same parameters for the SAGEM F st 1500 ADSL Router and all your wireless clients Sw k sacem fi ee S AD Home Save and Reboot Reset Logout A STATUS WEP SETUP WIZARD i i WEP is the basic mechanism to transmit your data securely over the wireless network Matching encryption keys must be setup on your SYSTEM router and wireless client devices to use WEP WAN LAN WEP Mode 64 bit 128 bit WIRELESS Channel and SSID Access control Key Provisioning Static ODynamic Key Entry Method Hex O ASCII Static WEP Key Setting 10 26 hex digits for 64 WEP 128 WEP FIREWALL Default Key ID 1 v ROUTE Qos ADVANCED Key 1 0101010101 Passphrase 1 32 characters Key 2 0202020202 Key 3 0303030303 Key 4 0404040404 J v Parameter Description WEP Mode Key Provisioning Select 64 bit or 128 bit key to use for encryption Select Static if there is only one fixed key for encryption If you want to select Dynamic you would need to enable 802 1x function first You may automatically generate encryption keys or manually enter the keys To generate the key automatically with passphrase check the Passphrase box enter a string of characters Sel
85. ormation Protocol parameters In this menu is included the following sub menus gt Static Route see section 4 9 1 gt RIP see section 4 9 2 gt Routing Table see section 4 9 3 4 9 1 Static Route JX k sacem ff i Reset Togo S ZA Home Save and Reboot Reset Logout STATUS Static Route SETUP WIZARD SYSTEM WAN Index Network Address Subnet Mask Gateway Configure LAN No Yalid Static Route Entry WIRELESS NAT FIREWALL ROUTE Please enter the following configuration parameters Routing Table Qos ADVANCED Click Add to add a new static route to the list or check the box of an already entered route and click Modify Clicking Delete will remove an entry from the list JX kZ sacem fi fl a S AD Home Save and Reboot Reset Logout STATUS Static Route SETUP WIZARD SYSTEM WAN Index Network Address Subnet Mask Gateway Configure LAN 1 k E i N A WIRELESS NAT FIREWALL ROUTE Static Route Please enter the following configuration parameters Routing Table Qos ADVANCED Check the box of the route you wish to delete or modify Subnet Mask Enter the subnet mask of he remote network Tor which to set a statie route SAGEM F st 1500 Reference Manual 288053220 04 Page 4 48 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 9 2 RIP eFON FIPS Save and Reboot
86. ou have a client computer that cannot run an Internet application properly from behind the firewall you can open the client up to unrestricted twoway Internet access Enter the IP address of a DMZ DeMilitarized Zone host on this screen Adding a client to the DMZ may expose your local network to a variety of security risks so only use this option as a last resort Ssacem OE STATUS DMZ SETUP WIZARD Save and Reboot Reset Logout If you have a local client PC that cannot run an Internet application properly from behind the NAT firewall then you can open the client up SYSTEM to unrestricted two way Internet access by defining a Virtual DMZ Host WAN LAN Enable DMZ Oves No WIRELESS Multiple PCs can be exposed to the Internet for two way communications e g Internet gaming video conferencing or YPN connections NAT To use the DMZ you must set a static IP address for that PC FIREWALL Access Control MAC Filter i 0 0 0 0 URL Blocking Schedule Rule Intrusion Detection DMZ ROUTE Qos ADVANCED Public IP Address Client PC IP Address SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 47 4 Configuring the SAGEM F st 1500 ADSL router 4 9 Route These pages define routing related parameters including static routes and RIP Routing Inf
87. oxy You need to verify that the HTTP Proxy feature of your web browser is disabled This is so that your browser can view the SAGEM F st 1500 ADSL Routers HTML configuration pages refer to Internet Explorer on 3 2 1 SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 3 13 3 Configuring Client Computer Obtain IP Settings from SAGEM F st 1500 ADSL Router Now that you have configured your computer to connect to your SAGEM F st 1500 ADSL Router it needs to obtain new network settings By releasing old DHCP IP settings and renewing them with settings from SAGEM F st 1500 ADSL Router you can verify that you have configured your computer correctly 1 On the Windows desktop click Start Programs Accessories Command Prompt Communications Command Prompt Faint WordPad Documents d Outlook Express Settings bol gt Search Help Run 2 Inthe Command Prompt window type IPCONFIG RELEASE and press the ENTER key Command Prompt Micrwocoft Windows 2000 Vercion 5 06 7195 CG Copyright 1785 1977 Microsoft Corp r r TL POOHFIG RELEASE Windows 26080 IP Conf igurat ion IP address successfully released For adapter Local Area Connection i SAGEM F st 1500 Reference Manual 288053220 04 Page 3 14 Reproduction and commu
88. ple virtual IPs from Global IP is transformed as multiple virtual IPs from Global IP is transformed as multiple virtual IPs from 10 Global IP is transformed as multiple virtual IPs from Help Apply Il Cancel SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 33 4 Configuring the SAGEM F st 1500 ADSL router 4 7 2 Virtual Server If you configure the SAGEM F st 1500 ADSL Router as a virtual server remote users accessing services such as web or FIP at your local site via public IP addresses can be automatically redirected to local servers configured with private IP addresses In other words depending on the requested service TCP UDP port number the SAGEM F st 1500 ADSL Router redirects the external service request to the appropriate server located at another internal IP address Ss k SAGEM E SS Re S La N Home Save and Reboot Reset Logout Virtual Server You can configure the router as a virtual server so that remote users accessing services such as the Web or FTP at your local site via public IP addresses can be automatically redirected to local servers configured with private IP addresses In other words depending on the requested service TCP UDP port number the router redirects the external service request to the appropriate server located at another internal IP add
89. pyright 2004 SAGEM SA All rights reserved You can now configure the modem router Navigating the Management Interface The SAGEM F st 1500 ADSL Router s management interface consists of a Setup Wizard and an Advanced Setup section Setup Wizard Use the Setup Wizard if you want to quickly set up the SAGEM F st 1500 ADSL Router Go to SETUP WIZARD on section 4 2 Advanced Setup Advanced Setup supports more advanced functions like hacker attack detection IP and MAC address filtering virtual server setup virtual DMZ host as well as other functions Go to Advanced Setup on section 4 11 You can also display router information on section 4 1 SAGEM F st 1500 Reference Manual 288053220 04 Page 4 4 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router Making Configuration Changes Configurable parameters have a dialog box or a drop down list Once a configuration change has been made on a page click the SAVE SETTINGS or NEXT button at the bottom of the page to enable the new setting To ensure proper screen refresh after a command entry be sure that Internet Explorer 5 0 is configured as follows Under the menu Tools Internet Options General Temporary Internet Files Settings the setting for Check for newer versions of stored pages should be Every visit to the page Some new Settings require
90. r a more secure Wireless network you can specify that only certain Wireless PCs can connect to the Access Point Up to 32 MAC addresses can be added to the MAC Filtering Table When enabled all registered MAC addresses are controlled by the Access Rule Enable MAC Filtering OYes No Access Rule for registered MAC address Odllow Deny MAC Filtering Table up to 32 stations ID MAC Address o 00 00 00 00 2 00 00 5 00 00 00 00 00 H 00 00 00 00 go Jeo e o0 g 00s 0 oo 00 00 00 oo 00 00 00 00 lt 00 j00 00 oo j00 Eloo 00 oo 00 00 00 o0 oo 00 00 00 00 oo soo e joo Joo oo Slo Eloo oo oo aloo 00 00 oo zlo 00 Elo 00 klo llo klo klo oo loo Eloo oo oo Slo loo oo 00 00 00 00 oo 00 00 00 00 SE pma En eee pn ame ees ie e mm m be H M m aa H fp m in a oa m J m co m D M m 00 00 00 00 o 00 00 00 00 00 00 00 M m M m M ian M o 00 00 o0 o 00 00 00 00 00 00 00 o 00 00 00 oo joo 00 joo 00 oo 00 00 00 o oo 00 o0 00 00
91. r homes e Internet Access This device supports Internet access through an ADSL connection Since many DSL providers use PPPoE or PPPOA to establish communications with end users the SAGEM F st 1500WG ADSL Router includes built in clients for these protocols eliminating the need to install these services on your computer SAGEM F st 1500 Reference Manual 288053220 04 Page 1 2 Reproduction and communication prohibited without the written permission of SAGEM SA 1 Introduction e Shared IP Address The SAGEM F st 1500WG ADSL Router provides Internet access for up to 253 users via a single shared IP address Using only one ISP account multiple users on your network can browse the web at the same time e Virtual Server If you have a fixed IP address you can set the SAGEM F st 1500WG ADSL Router to act as a virtual host for network address translation Remote users access various services at your site using a constant IP address Then depending on the requested service or port number the SAGEM F st 1500WG ADSL Router can route the request to the appropriate server at another internal IP address This secures your network from direct attack by hackers and provides more flexible management by allowing you to change internal IP addresses without affecting outside access to your network e DMZ Host Support Allows a networked computer to be fully exposed to the Internet This function is used when NAT and firewall se
92. rectable antenna 180 rotation not removable only for the SAGEM F st 1500WG SAGEM F st 1500 Reference Manual 288053220 04 Page 2 4 Reproduction and communication prohibited without the written permission of SAGEM SA 2 Description and physical installation 2 2 Physical Installation 2 2 1 Installation instructions Environment VV VV WV V Y The SAGEM F st 1500 must be installed and used inside a building The room temperature must not exceed 45 C The SAGEM F st 1500 must be placed on a desktop The SAGEM F st 1500 must not be exposed to strong sunlight or excessive heat The SAGEM F st 1500 must not be placed in an environment subject to significant steam condensation The SAGEM F st 1500 must not be exposed to splashed water The SAGEM F st 1500 casing must not be covered The SAGEM F st 1500WG and its peripheral devices must not be used for outdoor transmissions Power supply source gt The SAGEM F st 1500 s mains adapter block must not be covered The SAGEM F st 1500 router is supplied with its own power supply adapter It must not be used with any other adapter This Class Il adapter does not need to be earthed The connection to the electrical network must comply with the information on its label Use a readily accessible mains outlet near to the router The power supply lead is 2 m long Arrange the power supply lead to avoid any accidental disconnection o
93. ress This tool can support both port ranges multiple ports and combinations of the two For example Port Ranges ex 100 150 gt Multiple Ports ex 25 110 80 Address Mapping Combination ex 25 100 800 Virtual Server Special Application NAT Mapping Table FIREWALL ROUTE Qos ADVANCED Public Port Enable z g LAN IP Address Protocol Type v g ajjaja a a o o o o o j g El gt ajja aj 2 ojj 2 pa a 2 Q o g 1 2 v 3 v 4 v 5 v 6 v Ti v 8 v 9 o g NAANA s g o a Q oa a Q Q Q Q Qo ao a ao a a a Qa a a a a Oo oO oO o oO oO oO oO oO g g g 5 5 D p a 2 Q AIAZ gt ajja ajlo Le KIK a a Q BG eee ee ee eee eee eel ele E For example if you set Type Public Port to TCP 80 HTTP or web and the Private IP Port to 192 168 2 2 80 then all HTTP requests from outside users will be transferred to 192 168 2 2 on port 80 Therefore by just entering the IP address provided by the ISP Internet users can access the service they need at the local address to which you redirect them The more common TCP service ports include HTTP 80 FTP 21 Telnet 23 and POP3 110 A list of ports is maintained at the following link http www iana org assignments port numbers SAGEM F st 1500 Reference Manual 288053220 04 Page 4 34 Reproduction and comm
94. rmation section to confirm that the upgrade process was successful See ii Home Reset Logout STATUS Firmware Upgrade SETUP WIZARD This tool allows you to upgrade the router firmware using a file provided by us You can download the latest firmware from SYSTEM http www sagem com Time Settings Password Settings Enter the path and name or browse to the location of the upgrade file then click the Apply button You will be prompted to confirm the Configuration Tools upgrade to complete the process Firmware Upgrade a Firmware File Parcourir Reset LAN WIRELESS NAT FIREWALL ROUTE Qos ADVANCED 4 3 5 Reset Click REBOOT ROUTER to reset the SAGEM F st 1500 ADSL Router The reset will be completed when the power LED stops blinking Ssacem GL STATUS Reset SETUP WIZARD Home Reset Logout In the event that the system stops responding correctly or in some way stops functioning you can perform a reset Your settings will not SYSTEM be changed To perform the reset click on the Apply button below You will be asked to confirm your decision The reset will be complete Time Settings when the power light stops blinking Password Settings Configuration Tools Firmware Upgrade Reset WAN LAN WIRELESS NAT FIREWALL ROUTE Qos ADVANCED If you perform a reset from this page the configurations will not be changed back to the factory default settings Router perfo
95. rms a power reset If the button is depressed for over five seconds all If you use the Reset button on the front panel the SAGEM F st 1500 ADSL the LEDs will be lighted and the factory settings will be restored SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 15 4 Configuring the SAGEM F st 1500 ADSL router 44 WAN menu Specify the WAN connection parameters provided by your Internet Service Provider ISP The SAGEM F st 1500 ADSL Router can be connected to your ISP in one of the following ways gt ATM PVC see section 4 4 1 gt Clone MAC see section 4 4 2 Ssacem GE Home Reset Logout STATUS WAN SETUP WIZARD SYSTEM WAN ATM PYC To configure ATM YC parameters VC1 Clone MAG To configure WAN Interface MAC Address VC2 VC3 V C4 e VCS VC6 VC VCS Clone MAC Address LAN WIRELESS NAT FIREWALL ROUTE Qos ADVANCED The router can be connected to your service provider in any of the following ways SAGEM F st 1500 Reference Manual 288053220 04 Page 4 16 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 4 1 ATM PVC Enter ATM Asynchronous Transfer Mode function parameters here J k sacem i Reset Toont S AR Home Save and Reboot Reset Logout STATUS ATM Inter
96. rname In the field it appears the username that you entered during the SETUP WIZARD menu In the field it appears the Password that you entered during the SETUP WIZARD menu Confirm In the field it appears the Confirm Password that you entered during the SETUP WIZARD menu Password Specifies the maximum size of the payload data in IP packets as a number of bytes default value is 1400 The following parameters only appear in Routed mode that you can select in the Protocol field Default Gateway Default gateway of the ATM interface DHCP Client Check this box if your ISP assigns an IP to clients using DHCP SAGEM F st 1500 Reference Manual 288053220 04 Page 4 18 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 4 2 Clone MAC some ISPs require you to register your MAC address with them If this is the case the MAC address of the SAGEM F st 1500 ADSL Router must be changed to the MAC address that you have registered with your ISP S SAGEM STATUS SETUP WIZARD SYSTEM WAN eVC1 VC2 VC3 V C4 eVCS VC6 VC7 VCS Clone MAC Address LAN WIRELESS NAT FIREWALL ROUTE Qos ADVANCED TES AR Clone MAC Address Save and Reboot Reset Logout Some ISPs require you to register your MAC address with them If you have done this the MAC address of the Gateway must be changed to the MAC
97. rovided by your service provider 3 WEP Username username 4 Access control Password Crore Confirm Password eeccee Enter the PPPoA Point to Point Protocol over ATM settings provided by your ISP Parameter Description Username Enter the ISP assigned user name Password Enter your password Confirm Password Confirm your password This will automatically configure the SAGEM F st 1500 ADSL Router with the correct Protocol Encapsulation and VPI VCI settings for your ISP Click Next the router will try to connect to the Internet Se i 1 PPP settings 2 Channel and SSID 3 WEP Connecting to Internet Please wait 4 Access control SAGEM F st 1500 Reference Manual 288053220 04 Page 4 8 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router Once the ADSL Router has been connected to the Internet you get the following message SZ S sacem i 1 PPP settings 2 Channel and SSID 3 WEP Pig eee eae You are connected to the Internet 4 2 2 Channel and SSID Now you can start the wireless configuration 1 PPP settings 2 Channel and SSID 2 Channel and SSID This page allows you to define SSID and Channel ID for wireless connection In the wireless 3 WEP environment the router can also act as an wireless access point These parameters are used for the mobile stations to
98. rs support the protocol e IP Security Provides IP network layer encryption IPSec can support large encryption networks such as the Internet by using digital certificates for device authentication SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 1 3 1 Introduction 1 4 Composition of the supply The SAGEM F st 1500 is supplied in a package with gt one SAGEM F st 1500 router or gt one SAGEM F st 1500WG router gt one mains adapter unit gt one RJ11 RJ11 lead length 3 m gt one crossed RJ45 RJ45 Ethernet lead length 1 8 m gt one CD ROM gt ADSL filters optional gt wireless accessories optional Note This list is by no means exhaustive the package may also include safety instructions and other documents The CD ROM contains e the software for installing the four Ethernet and wireless interfaces e the SAGEM F st 1500 User Guide in pdf file format e the Acrobat Reader software for reading pdf files Incomplete or If the equipment is received damaged or incomplete contact the damaged supply supplier of your SAGEM F st 1500 router SAGEM F st 1500 Reference Manual 288053220 04 Page 1 4 Reproduction and communication prohibited without the written permission of SAGEM SA 1 Introduction 1 5 Prerequisites To use the SAGEM F st 1500 you must have gt aline supporting ADS
99. s a template that identifies the address bits in the destination address used for routing to specific subnets Each bit that corresponds to a 1 is part of the subnet mask number each bit that corresponds to 0 is part of the host number The IP address of the router at the next hop to which frames are forwarded Interface The local interface through which the next hop of this route is reached When a router receives a routing update that contains a new or changed destination network entry the router adds 1 to the metric value indicated in the update and enters the network in the routing table SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 51 4 Configuring the SAGEM F st 1500 ADSL router 4 10 QoS The QoS function allows users to classify outbound traffic of applications and provides differentiated services Diffserv for different applications Home Save and Reboot Reset STATUS QoS Settings SETUP WIZARD The bandwidth gap between LAN and WAN may significantly degrade performance of critical network applications such SYSTEM as VoIP gaming and VPN This QoS function allows users to classify traffic of applications and provides them with WAN differentiated services Diffserv LAN WIRELESS Enable or disable QoS module function Enable Disable NAT Diffserv Forwarding Groups FIREWALL Below
100. s parameters Tka ISETUP WIZARD SYSTEM Enter parameters of the profile to define a VLAN WAN LAN gt VLAN 2 DNS WIRELESS Subnet Mask 255 255 255 o VLAN Parameters Description Default IP Address 192 168 2 f I NAT NAT Domain Private Public FIREWALL IGMP Snooping OeEnabled Disabled ROUTE IGMP Querier O Enabled Disabled Qos ADVANCED HELP SAVE SETTINGS CANCEL Enter parameters of the profile to define a VLAN then click on the SAVE SETTING button to take into account the entered parameters Add VLAN Click on Add VLAN allows to create a new VLAN entry STATUS SETUP WIZARD VLAN Parameters Enter parameters of the profile to define a VLAN Description IP Address 0 0s 0 Jo WIRELESS Subnet Mask 255 255 255 0 NAT NAT Domain Private Public FIREWALL IGMP Snooping O Enabled Disabled ROUTE IGMP Querier O Enabled Disabled Qos ADVANCED HENE SAVE SETTINGS CANCEL Enter parameters of the profile to define a VLAN then click on the SAVE SETTING button to take into account the entered parameters When you have created a VLAN profile another Delete button appears in the Configure field and allows you to modify profile parameters or delete a VLAN profile SAGEM F st 1500 Reference Manual 288053220 04 Page 4 22 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the
101. shows the Diffserv forwarding behaviors this router supports User can further configure the bandwidth allocation ROUTE of each forwarding behavior Qos res a Bandwidth Allocation Name Descnption Prority Mi Al N inimum ow More Traffic Mapping x 25 Traffic Statistics BE Best Effort forwarding Lowest h AF 1x 0 v ADVANCED Assured Forwarding provides delivery Low g of packets in four independently mek forwarded AF classes Within each AF f 0 class an IP packet can be assigned AF3 one of three different levels of drop 0 m recedence h ara P Hig 75 lop a Expedited Forwarding is intended to EF provide low delay low jitter and low Highest 0 l v loss delivery of packets Help Cancel v The following items are on the QoS Settings screen Parameter Description Enable or disable QoS module function Click Enable to activate QoS module function Diffserv Forwarding Groups Allow users to configure guaranteed bandwidth of each Forwarding Group EF AF4x to AF1x and BE Please complete the Minimum Bandwith Allocation field The amount of guaranteed bandwidth for the Forwarding Groups must not be over 100 The displayed values 25 and 75 are only given as an example Allow to limit whether or not the guaranteed bandwidth of each Forwarding Group by checking or not the Allow More box In this menu are included the following sub menus gt Traffic Mapping see section 4 10 1 gt Traffic st
102. sion of SAGEM SA C Appendix C CABLES This chapter covers gt Ethernet cable section C 1 gt ADSL cable Section C 2 SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page C 1 Appendix C Cables C 1 Ethernet cable DO NOT plug a phone jack connector into any RJ 45 port Use only twisted pair cables with RJ 45 connectors that conform with FCC standards C 1 1 Specifications Cable Types and Specifications Cable Max Length Connector 10BASE T Cat 3 4 5 100 ohm UTP 100 m 328 ft RJ 45 100BASE TX Cat 5 100 ohm UTP 100 m 328 ft RJ 45 C 1 2 Wiring Conventions For Ethernet connections a twisted pair cable must have two pairs of wires Each wire pair is identified by two different colors For example one wire might be red and the other red with white stripes Also an RJ 45 connector must be attached to both ends of the cable Each wire pair must be attached to the RJ 45 connectors in a specific orientation The following figure illustrates how the pins on an Ethernet RJ 45 connector are numbered Be sure to hold the connectors in the same orientation when attaching the wires to the pins lt gt N ej r Figure C 1 RJ 45 Ethernet Connector Pin Numbers C 1 3 RJ 45 Port Connection Use the straight through CAT 5 Ethernet cable provided in the package to connect the Sagem F st1500 ADSL Router to your PC Whe
103. sions number from same host hooo Incomplete TCP UDP sessions detect sensitive time period bo tt msec Maximum half open fragmentation packet number from same host fo Half open fragmentation detect sensitive time period hoo ooo msec Flooding cracker block time 300 sec SAGEM F st 1500 Reference Manual 288053220 04 Page 4 44 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router When particular types of traffic are checked only the particular type of traffic initiated from the internal LAN will be allowed For example if the user only checks FTP Service in the Stateful Packet Inspection section all incoming traffic will be blocked except for FTP connections initiated from the local LAN Stateful Packet Inspection allows you to select different application types that are using dynamic port numbers If you wish to use the Stateful Packet Inspection SPI to block packets click on the Yes radio button in the Enable SPI and Anti DoS firewall protection field and then check the inspection type that you need such as Packet Fragmentation TCP Connection UDP session FTP Service H 323 Service or TFTP Service 3 When hackers attempt to enter your network we can alert you by e mail Enter your email address Specify your SMTP and POP3 servers user name and password 4 Connection Policy Enter the appropriate values for TCP UDP sess
104. t does not protect any transmissions over your wired network or over the Internet SAGEM F st 1500 Reference Manual 288053220 04 Page 4 10 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 2 4 Access Control Access Control allows users to define the outgoing traffic permitted or not permitted through the Wi Fi interface The default is to permit all outgoing traffic The following items are on the Access Control screen gt Click Yes to turn on the filtering function or No to disable this function lf you have enabled this function you can enter the client MAC addresses that you want to filter S SAGEM 1 PPP settings 2 Channel and SSID 3 WEP 4 Access control You can give up to 32 client stations TES AR Home Save and Reboot Reset Logout A 4 Access control For a more secure Wireless network you can specify that only certain Wireless PCs can connect to the Access Point Up to 8 MAC addresses can be added to the MAC Filtering Table When enabled all registered MAC addresses are controlled by the Access Rule Enable MAC Filtering OYes No Access Rule for registered MAC address Odallow Deny MAC Filtering Table up to 8 stations MAC Address 00 z 00 lo e 00 slo e 00 io T ie Boo 00 laid 00 le loo 00
105. t telephony SR OE Save and Reboot Reset Logout STATUS Special Application SETUP WIZARD T ai 3 Some applications require multiple connections such as Internet gaming video conferencing Internet telephony and others These applications cannot work when Network Address Translation NAT is SYSTEM enabled If you need to run applications that require multiple connections specify the port normally associated with an application in the Trigger Port field select the protocol type as TCP or UDP then WAN enter the public ports associated with the trigger port to open them for inbound traffic Note The range of the Trigger Ports is from 1 to 65535 LAN WIRELESS Trigger Port NAT Address Mapping TY TCP l i Virtual Server a OuDP J Special Application NAT Mapping Table FIREWALL ROUTE TCP Qos i Oubp ADVANCED Trigger Public Port Enabled Type TCP O upP O TCP Oupp TCP O upP TCP O upP TCP Oupp TCP O UDP TCP O uDP TCP Oupp Popular applications select one COPY TO Help Apply Cancel These applications may not work when Network Address Translation NAT is enabled If you need to run applications that require multiple connections use these pages to specify the additional public ports to be opened for each application SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohi
106. tal incomplete TCP UDP sessions LOW Incomplete TCP UDP sessions per min HIGH Incomplete TCP UDP sessions per min LOW Maximum incomplete TCP UDP sessions number from same host Incomplete TCP UDP sessions detect sensitive time period Maximum half open fragmentation packet number from same host Half open fragmentation detect sensitive time period Flooding cracker block time Defaults Description 300 sessions Defines the rate of new unestablished sessions that will cause the software to start deleting half open sessions 250 sessions Defines the rate of new unestablished sessions that will cause the software to stop deleting halfopen sessions 250 sessions Maximum number of allowed incomplete TCP UDP sessions per minute 10 Maximum number of incomplete TCP UDP sessions from the same host 300 msec Length of time before an incomplete TCP UDP session is detected as incomplete 30 Maximum number of half open fragmentation packets from the same host 10000 msec Length of time before a half open fragmentation session is detected as half open 300 second Length of time from detecting a flood attack to blocking the attack Minimum number of allowed incomplete TCP UDP sessions per minute SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 8 6 DMZ If y
107. talling a Full Rate Connection If you are using a full rate G dmt connection your service provider will attach the outside ADSL line to a data voice splitter In this case you can connect your phones and computer directly to the splitter as shown below System POTS ADSL Router aoa Eth ernet hub or switch Figure 2 3 Installing with a Splitter SAGEM F st 1500 Reference Manual 288053220 04 Page 2 8 Reproduction and communication prohibited without the written permission of SAGEM SA 2 Description and physical installation Installing a Splitterless Connection If you are using a splitterless G lite connection then your service provider will attach the outside ADSL line directly to your phone system In this case you can connect your phones and computer directly to the incoming ADSL line but you will have to add low pass filters to your phones as shown below Plain Old k Telephone Eo System POTS f 7 Voice es Residential Filter Gonn ection i Voice j Point Network amp Data interface Device HID T ra Voice EF i amp Data L yam ADSL Router zi Data a o a 1 gg Ethernet p hub or switch Figure 2 4 Installing without a splitter SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 2 9 2 Description and physical installation 2 3 9
108. ted without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 7 1 Address Mapping This feature allows one or more public IP addresses to be shared by multiple internal users This also hides the internal network for increased privacy and security Enter the Public IP address you wish to share into the Global IP field Enter a range of internal IPs that will share the global IP into the from field XN k sacem fj El i aa S AA Home Save and Reboot Reset Logout Address Mapping Network Address Translation NAT allows IP addresses used in a private local network to be mapped to one or more addresses used in the public global Internet This feature limits the number of public IP addresses required from the ISP and also maintains the privacy and security of the local network We allow one or more than one public IP address to be mapped to a pool of local addresses Address Mapping 1 Global IP is transformed as multiple virtual IPs gt Address Mapping from gt Virtual Server Special Application gt NAT Mapping Table from 2 Global IP is transformed as multiple virtual IPs 3 Global IP is transformed as multiple virtual IPs from 4 Global IP is transformed as multiple virtual IPs from 5 Global IP is transformed as multiple virtual IPs from 6 Global IP is transformed as multiple virtual IPs from 7 Global IP is transformed as multi
109. ted without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router Monitoring Index The Status screen displays information on connection line status data rate operation data and defect indication and statistics Scroll down to view more information STATUS ADSL SETUP WIZARD l 7 This page allows you to specify the ADSL standards to operate with You may explicitly set a specific standard SYSTEM or choose Automatic to automatically negotiate with remote DSLAM WAN LAN Operation Mode Automatic v WIRELESS NAT FIREWALL ADSL Status Information ROUTE Status Data Rate Information Qos Defect Failure Indication ADVANCED Statistics ADSL Remote Management Monitoring Index a Status Configured Current SNMP Line Status QUIET UPnP Link Type Interleaved Path DDNS Go Top a Data Rate Stream Type Actual Data Rate Up Stream 0 Kbps Down Stream 0 Kbps Go Top Operation Data Defect Indication Operation Data Upstream Downstream Noise Margin 0 dB 0 dB Attenuation 0 dB 0 dB Indicator Name Near End Indicator Far End Indicator Fast Path FEC Correction 0 Interleaved Path FEC Correction 0 Fast Path CRC Error 0 Interleaved Path CRC Error 0 Loss of Signal Defect Fast Path HEC Error Interleaved Path HEC Error Go Top a Statistics Received Cells Transmitted Cells Go Top SAGEM F st 1500 Reference Manual
110. ten permission of SAGEM SA 3 Configuring Client Computer 3 Type IPCONFIG RENEW and press the ENTER key Verify that your IP Address is now 192 168 2 xxx your Subnet Mask is 255 255 255 0 and your Default Gateway is 192 168 2 1 These values confirm that your SAGEM F st M 1500 ADSL Router is functioning Type EXIT and press the ENTER key to close the Command Prompt window ce Command Prompt C Documents and Settings sagem ipconfig re lease Windows IP Configuration Ethernet adapter Local Area Connection Connection specific DAS Suffix IP Address Se ee es oR a Se ee ee oe AB n Subnet Mask 4 8 6 8 Default Gateway yey vais tec te C gt 5 Documents and Settings sagem gt ipconf ig renew Mindows IP Configuration Ethernet adapter Local Area Connection Connection specific DHS Suffix IP Address 2 ow n a a T 1922168 22 2 Subnet Mask a naa a l 255 255 2558 Default Gateway a a a a a a a 192 168 2 1 C Documents and Settings sagem gt Your computer is now configured to connect to the SAGEM F st 1500 ADSL Router SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 3 19 3 Configuring Client Computer 3 3 Configuring your Mac computer You may find that the instructions here do not exactly match your operating system This is because these steps and
111. ters are used for the mobile stations to connect to this access point LAN SSID SAGEM WIRELESS Channel and SSID Access control Wireless Mode Mixed 11b 11g v SSID Broadcast ENABLE DISABLE Channel Auto v FIREWALL ROUTE Qos ADVANCED Service Set ID The ESSID must be the same on the SAGEM F st 1500 ADSL Router and all of its wireless clients SSID Broadcast Enable or disable the broadcasting of the SSID Wireless Mode This device supports both 11g and 11b wireless networks Make your selection depending on the type of wireless network that you have Channel The radio channel used by the wireless router and its clients to communicate with each other This channel number must be the same on the ADSL Router and all of its wireless clients SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 25 4 Configuring the SAGEM F st 1500 ADSL router 4 6 2 Access Control Access Control allows users to define the outgoing traffic permitted or not permitted through the Wi Fi interface The default is to permit all outgoing traffic The following items are on the Access Control screen STATUS SETUP WIZARD SYSTEM WAN LAN WIRELESS Channel and SSID Access control Security WEP WPA 802 1 NAT FIREWALL ROUTE Qos ADVANCED Save and Reboot Reset Logout Access Control Fo
112. tly more overhead SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 17 4 Configuring the SAGEM F st 1500 ADSL router QoS Class Constant Bit Rate It is used for voice application Variable Bit Rate It is used for video application Unspecified Bit Rate It is used in Best Effort for IP and Ethernet for Data Application PCR SCR MBS Peak Cell Rate defined in number of cells second Sustainable Cell Rate defined in number of cells second MBS Maximum Burst Size defined in number of cells second IP assigned by Click Yes or No to assign or no IP address to your ISP ISP IP Address IP address of the ATM interface Subnet Mask Subnet mask of the ATM interface Connect Type e Always connected e Auto Triggered by traffic Manual Start in Disconnected e Manual Start in Disconnected e Manual Start in Last State Your router is always connected to the WAN automatic mode Your router only connect to WAN when traffic is on automatic mode When your router start this is disconnected to WAN Manual mode When your router start this is connected to WAN Manual mode When your router start this connect to WAN in last stated Manual mode Idle Time Minute Enter the maximum idle time for the Internet connection After this time has been exceeded the connection will be terminated Use
113. ule Rule Site Intrusion Detection Site DMZ ROUTE Qos ADVANCED Rule Number URL Keyword Rule Number URL Keyword Site 1 Site Site Site Site Site Site Site Site Site Site Site Site Site Site Wop pies PCA Pte a pes a Ea Site Site Site o Site Site Site Site Site Site Site Site Site Site You can define up to 30 sites here SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 41 4 Configuring the SAGEM F st 1500 ADSL router 4 8 4 Schedule Rule You may filter Internet access for local clients based on rules Each access control rule may be activated at a scheduled time Define the schedule on the Schedule Rule page and apply the rule on the Access Control page Ssacem FE Save and Reboot Reset Logout STATUS Schedule Rule SETUP WIZARD SYSTEM WAN Schedule Rule Table up to 10 rules LAN WIRELESS This page defines schedule rule names and activates the schedule for use in the Access Control page Rule Comment Configure No Yalid Schedule Rule Rule Name NAT FIREWALL Access Control MAC Filter URL Blocking Schedule Rule Intrusion Detection D
114. ult Gateway is 192 168 2 1 These values confirm that your SAGEM F st 1500 ADSL Router is functioning Click OK to close the IP Configuration window Run 7 m ype the name of a program folder document of Internet resource and Windows will open it for you Windows Update Open WINIPCFE o Programs Favontes Docunents IP Configuration fei Settings Ethernet Adapter Information Find Adapter Address 00 E0 29 75 35 9E Help IF Address 192 168 2 161 K Subnet Mask 255 255 255 0 Default Gatewar 132 168 2 1 Log Cit larson Shut D owr OK Release Release All Senew All More Info gt SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 3 7 3 Configuring Client Computer 3 2 2 On Windows NT 4 0 1 On the Windows desktop click Start Settings Control Panel Control Panel Printers Taskbar amp Start Menu Settings d g pa Add Remove Console Date T ime Programs F Ports Printers Regonal SUSI Adapters Server Services Settings a Sounds System Tape Devices Telephony 25 object s Me SAGEM F st 1500 Reference Manual 288053220 04 Page 3 8 Reproduction and communication prohibited without the written permission of SAGEM SA 3 Configuring Client Computer 2 Double click the Network icon 3 In the Network win
115. unication prohibited without the written permission of SAGEM SA 4 Configuring the SAGEM F st 1500 ADSL router 4 7 3 Special Application S sacem OE STATUS Special Application SETUP WIZARD Save and Reboot Reset Logout Some applications require multiple connections such as Internet gaming video conferencing Internet telephony and others These applications cannot work when Network Address Translation NAT is SYSTEM enabled If you need to run applications that require multiple connections specify the port normally associated with an application in the Trigger Port field select the protocol type as TCP or UDP then WAN enter the public ports associated with the trigger port to open them for inbound traffic Note The range of the Trigger Ports is from 1 to 65535 Trigger Public Public Port Enabled WIRELESS Trigger Port Type Type NAT Address Mapping TCP Otcp S Virtual Server Oupp Oupp Special Application NAT Mapping Table TCP r TCP O upP OupP E FIREWALL ROUTE TCP TCP Qos 3 Oupp Oupp ADVANCED Tep TCP OuDP O uDP OTER TCP Oupp Ouopp TCP tTep Oupp Oupp TCP TCP OuDP OupP TCP TCP OuDP Oupp TCP TCP OuDP OuDP tce TCP OuDP Oupp Popular applications select one v COPY TO Help Apply Cancel Some applications require multiple connections such as Internet gaming video conferencing and Interne
116. vate to prevent unauthorized individuals from accessing information on your system Version Sets the trap status to disabled or enabled with V1 or V2c The v2c protocol was proposed in late 1995 and includes enhancements to v1 that are universally accepted These include a get bulk command to reduce network management traffic when retrieving a sequence of MIB variables and a more elaborate set of error codes for improved reporting to a Network Management Station 4 11 4 UPnP Click Enable to turn on the Universal Plug and Play function of the ADSL Router This function allows the device to automatically gt dynamically join a network gt obtain an IP address X k sacem i T S ain Home Save and Reboot Reset STATUS UPnP SETUP WIZARD 2 The Universal Plug and Play architecture offers pervasive peer to peer network connectivity of PCs of all form SYSTEM factors intelligent appliances and wireless devices UPnP enables seamless proximity network in addition to WAN control and data transfer among networked devices in the home office and everywhere in between LAN WIRELESS Enable or disable UPnP module function eEnable ODisable NAT FIREWALL ROUTE Qos ADVANCED ADSL Remote Management SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 61 4 Configuring the SAGEM F st 1500 ADSL router 4 11 5 DDNS DDN
117. word with a randomly generated number sent by users the server Check the box of the user you wish to modify Username Defines the user name of olens Password Set the single use password for the clients New Create anew Tiny series accout SAGEM F st 1500 Reference Manual 288053220 04 Reproduction and communication prohibited without the written permission of SAGEM SA Page 4 31 4 Configuring the SAGEM F st 1500 ADSL router 4 7 NAT Network Address Translation allows multiple users to access the Internet sharing one public IP 3X k Ssacem GE Save and Reboot Reset Logout STATUS NAT SETUP WIZARD Network Address Translation NAT allows multiple users at your local site to access the Internet through a single public IP address or SYSTEM multiple public IP addresses NAT can also prevent hacker attacks by mapping local addresses to public addresses for key services such as WAN the Web or FTP Enable or disable NAT module function Enable Disable WIRELESS NAT Address Mapping Virtual Server Special Application NAT Mapping Table FIREWALL ROUTE Qos ADVANCED In this menu is included the following sub menus gt Address Mapping see section 4 7 1 gt Virtual Server see section 4 7 2 gt Special Application see section 4 7 3 gt NAT Mapping Table see section 4 7 4 SAGEM F st 1500 Reference Manual 288053220 04 Page 4 32 Reproduction and communication prohibi
118. yption and MAC address filtering It is simple to configure and can be up and running in minutes 1 2 Features and Benefits Internet connection to an ADSL modem via an RJ 11 ADSL port Local network connection via four 10 100 Mbps Ethernet ports On board IEEE 802 11g wireless network adapter DHCP for dynamic IP configuration and DNS for domain name mapping Firewall with Stateful Packet Inspection client privileges intrusion detection and NAT Y VV VV WV NAT also enables multi user Internet access via a single user account and virtual server functionality providing protected access to Internet services such as web FTP e mail and Telnet VPN pass through IPSec ESP Tunnel mode L2TP PPTP User definable application sensing tunnel supports applications requiring multiple connections v WV Easy setup through a web browser on any operating system that supports TCP IP Compatible with all popular Internet applications QoS for outbound traffic classification and bandwidth configuration based on Diffserv Dynamic DNS for mapping a static Domain Name to a dynamic IP address SIP Pass through VV VV WV 1 3 Applications Many advanced networking features are provided by the SAGEM F st 1500WG ADSL Router e Wireless and Wired LAN The SAGEM F st 1500WG ADSL Router provides connectivity to 10 100 Mbps devices and wireless IEEE 802 119 compatible devices making it easy to create a network in small offices o

Sagem SAGEMFAST 1500 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents