Renesas PCA7412E4S-64 User's Manual
Contents
1. LENESAS PCA7412E4S 64 PROM programming adapter for M16C 6V Group MCUs User s Manual Rev 1 00 September 1 2003 REJ10J0337 0100Z Renesas Technology www renesas com R4945 and R4945A are trademarks of Advantest Corporation 264 1300 00 0602J is a trademark of Sumitomo 3M Limited Keep safety first in your circuit designs Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products better and more reliable but there is always the possibility that trouble may occur with them Trouble with semiconductors may lead to personal injury fire or property damage Remember to give due consideration to safety when making your circuit designs with appropriate measures such as i placement of substitutive auxiliary circuits ii use of nonflammable material or iii prevention against any malfunction or mishap Notes regarding these materials These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited to the customer s application they do not convey any license under any intellectual property rights or any other rights belonging to Renesas Technology Corporation Renesas Solutions Corporation or a third party Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage or infringement of any third party s rights originating in the use of any product data d2. 20 Di JAPAN Figure 4 3 Inserting MCU AN CAUTION When Inserting an MCU e When inserting and pulling out the MCU be sure to keep the IC socket side above and horizontal 4 5 Precautions When Handling the Adapter Do not directly touch the connector in the IC socket and the pins on the PROM programmer connector otherwise dirt may cause an electrical insulation failure When not using this product attach the connector pins of this product to the conductive sponge as it was shipped from the factory 10 16 4 6 Setting Programming Area When writing and erasing programs be sure to set the programming area And also specify its device of the PROM programmer Table 4 2 Programming area PROM programmer Internal ROM MCU type name ROM size area of MCU Device Programming area OSDROM 128K bytes 1000016 2FFFFis 9000016 AFFFFis M306V5EESP M5M27C401 Internal ROM 192K bytes 5000016 7FFFFie DOOOO16 FFFFF16 AN CAUTION When Setting the Programming Area 1 Choose the programming mode properly Incorrect setting may destroy the MCU 2 The programming method in M5M27C401 mode is the byte programming method 11 16 5 Recommended PROM Programmers The PROM programmers listed in Table 5 1 are recommended for this product Using the actual products we have verified that these PROM programmers can be used to write programs without problem Nonconformit
3. items listed in Table 2 1 Check to see that it contains all of the items Table 2 1 Contents Main unit PCA7412E4S 64 Interface unit PCA7412C Connector PCA7402E 32 pin User s manual This manual If any part is missing or there is any doubt about your product package contact your local distributor 6 16 3 Specifications Table 3 1 lists the common specifications of the programming adapters and Table 3 2 lists the specifications of the PCA7412E4S 64 Table 3 1 Common specifications of the programming adapters Description 8 MHz Operating clock frequency 1 i i Supplied by the mounted ceramic oscillator Power supply Supplied from Vcc of the PROM programmer Board to insert a programmable MCU Main unit IC socket mounted on it Interface board Buffer IC mounted on it Board PCA7412C Connected by two rows of standard pitch 20 pin connectors configuration Interface unit and two rows of standard pitch 16 pin connectors to the upper and lower boards PCA7402E Board to connect to the PROM programmer Connector Standard pitch 32 pin pin header mounted Table 3 2 Specifications of PCA7412E4S 64 Product name Description McU M306V5EESP PCA7412E4S 64 64 pin 1 778 mm pitch SDIP IC socket 264 1300 00 0602J Sumitomo 3M Limited 7 16 4 How to Write the Program This chapter describes how to write programs with a PROM programmer For details on how
4. socket of the PROM programmer Be careful when attaching to the PROM programmer because incorrect insertion can cause fatal damage to the MCU PCA4702E connector qu m OOOO OO OOOO 00 des 100000000000000 o r32 pin IC socket of PROM programmer m m Nimo Figure 4 1 Attaching the adapter to a PROM programmer 4 3 Setting the Jumper Switch 1 Jumper switch SW1 You can not set the SW1 to IM Set this switch to 4M to use For details on the jumper switch setting see Table 4 1 and Figure 4 2 SWI1 IM Prohibited eSWl1 4M To write to OSD Internal ROM OSDROM Internal ROM SW1 4M 1M Note SW1 4M Do not change this setting Figure 4 2 Jumper switch setting 9 16 4 4 Inserting an MCU into the Programming Adapter As shown in Figure 4 3 insert the No 1 pin of the MCU into the No 1 pin of the IC socket on the main unit Be careful when inserting the MCU because incorrect insertion can cause fatal damage to the MCU Top view ICI o ne JI 33 J2 E MA z o1 4201 Le NL to gpz I w 1 No 1 pin of MCU ZZ o aao seoj um gt i NO i vi 3 i m j wy ES SI GR bo 1 wn 1 A o IC socket E mu Ko Koj 20
5. ge to your properties This chapter describes precautions which should be taken in order to use this product safely and properly Be sure to read this chapter before using this product 1 1 Safety Symbols and Meanings If the requirements shown in the WARNING AN WARNING sentences are ignored the equipment may cause serious personal injury or death If the requirements shown in the CAUTION AN CAUTION sentences are ignored the equipment may malfunction IMPORTANT important information on using this In addition to the three above the following are also used as appropriate Z means WARNING or CAUTION Example 4 CAUTION AGAINST AN ELECTRIC SHOCK O means PROHIBITION Example Q DISASSEMBLY PROHIBITED means A FORCIBLE ACTION Example UNPLUG THE POWER CABLE FROM THE RECEPTACLE The following page describes the symbols WARNING CAUTION and IMPORTANT 4 16 ZN WARNING Warnings for Use Environment e This equipment is to be used in an environment with a maximum ambient temperature of 35 C Care should be taken that this temperature is not exceeded e Select the proper programming mode of the PROM programmer N CAUTION Cautions to Be Taken for Modifying This Product GD e Do not disassemble or modify this product Disassembling or modifying this product can cause damage Cautions to Be Taken for Handling This Product A e Use caution when handling this product Be careful not to a
6. iagrams charts programs algorithms or circuit application examples contained in these materials All information contained in these materials including product data diagrams charts programs and algorithms represents information on products at the time of publication of these materials and are subject to change by Renesas Technology Corporation and Renesas Solutions Corporation without notice due to product improvements or other reasons It is therefore recommended that customers contact Renesas Technology Corporation Renesas Solutions Corporation or an authorized Renesas Technology product distributor for the latest product information before purchasing a product listed herein The information described here may contain technical inaccuracies or typographical errors Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage liability or other loss rising from these inaccuracies or errors Please also pay attention to information published by Renesas Technology Corporation and Renesas Solutions Corporation by various means including the Renesas home page http www renesas com When using any or all of the information contained in these materials including product data diagrams charts programs and algorithms please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products Renesas Technology Corporation and Renesas Solu
7. m development and evaluation stages In mass producing your program you have finished developing be sure to make a judgment on your own risk that it can be put to practical use by performing integration test evaluation or some experiment else In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge However this does not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any circumstances This product has been developed by assuming its use for program development and evaluation in laboratories Therefore it does not fall under the application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when used in Japan Renesas Tools Homepage http www renesas com en tools 2 16 Contents Precautions for Saleby isis psi stopis puso skoto vaca sestue sib ad sbeupes au sko kaki Renee ee 4 1 1 Safety Symbols and Meanings 0 eee ec eececceeeeeeeeeeeeeeeseecseeseecaecaecaessaeeseensees 4 2 Introduction EN 6 2 1 Things to Check When Unpacking ooooconicnoccnccnncnnonnnononnnonncononononnccnnonnccnncnnocnnconoos 6 SESPecwicatlOns ci So eee Se el enue a ale nae eee geaj 7 4 How to Write the Progra x os simpa drs nek sr iii 8 4 1 Progra
8. mming Procedures o0 ee ee eee ceesecseeesececesececeseeeeeseeseceseseeeeseeeaecneeeaeeaee 8 4 2 Attaching the Adapter to a PROM Programmer eeiseeseee sesnee ite 9 4 3 Setting the Jumper Switch oo ee ceeseeceneseeceeseecsecssen sees seossoonsessconsensonesen sees 9 4 4 Inserting an MCU into the Programming Adapter sees rene ener 10 4 5 Precautions When Handling the Adapter ooococcnccnonccocconnnonnnanconnnnncnncnnnonncin conan 10 4 6 Setting Programming Area oo elect cee cee ceseeeeceseeeeceeeeseceseeeeecaeeeaecaaesaesnaesaees 11 5 Recommended PROM Programmers eoocococcocnconcnononncnnnonncnnncnnconncn nono co nonnnonnnnnn narnia ran crnncnnos 12 6 Memory Map sus Su isto a tios 13 7 How to Request for Support 5 sis siso istostsasksb speak vbeas Au yess ead sesa vokon ek aE EsTe ss 14 To use the product properly Precautions for Safety O e In both this User s Manual and on the product itself several icons are used to insure proper handling of this product and also to prevent injuries to you or other persons or damage to your properties e The icons graphic images and meanings are given in Chapter 1 Precautions for Safety Be sure to read this chapter before using the product 3 16 1 Precautions for Safety In this user s manual several icons are used to insure proper handling of this product and also to prevent injuries to you or other persons or dama
9. oms Fails blank check Cannot write a program Fails verification etc e Detailed symptoms e How often does the problem occur 2 out of 10 etc e When did the problem start to occur Since purchase Used to work correctly e Type name of the PROM programmer Advantest R4945A etc e Specified device when writing to PROM M27C101 etc e Specified programming area when writing to PROM e Switch settings of the adapter when writing to PROM 14 16 PCA7412E4S 64 User s Manual Rev 1 00 September 1 2003 REJ10J0337 0100Z COPYRIGHT 2003 RENESAS TECHNOLOGY CORPORATION AND RENESAS SOLUTIONS CORPORATION ALL RIGHTS RESERVED TENESAS Renesas Technology Corp 2 6 2 Ote machi Chiyoda ku Tokyo 100 0004 Japan
10. pply a mechanical shock such as falling e Do not touch the connector pins of this product e Be careful with the static electricity when handling this product and the MCU When Not Using This Product for a Long Time 1 Attach the connector pins of this product to the conductive sponge 2 Put it into a conductive polyvinyl and keep it in the package case shipped from the factory 3 Store it in the place where humidity and temperature are low and direct sunshine does not strike IMPORTANT When Using The Product e Attach this product to the IC socket on the PROM programmer properly e Insert the MCU to the IC socket of this product properly e When opening and closing the IC socket of this product be sure to keep it horizontal e Be sure to set the programming area as described in this user s manual Do not use the PROM programmer s device identification code readout function 5 16 2 Introduction This product is a PROM programming adapter for M16C 6V Group of 16 bit MCUs The adapter is a tool that can be used to write programs into internal ROM of microcomputers using a commercially available PROM programmer This manual describes the specifications and the operation Figure 2 1 shows the external view and constituent parts of the adapter va Main unit Interface unit Connector Figure 2 1 External view and constituent parts 2 1 Things to Check When Unpacking This product consists of the
11. tions Corporation assume no responsibility for any damage liability or other loss resulting from the information contained herein Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake Please contact Renesas Technology Corporation Renesas Solutions Corporation or an authorized Renesas Technology product distributor when considering the use of a product contained herein for any specific purposes such as apparatus or systems for transportation vehicular medical aerospace nuclear or undersea repeater use The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or reproduce in whole or in part these materials If these products or technologies are subject to the Japanese export control restrictions they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination Any diversion or reexport contrary to the export control laws and regulations of Japan and or the country of destination is prohibited Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the products contained therein Precautions to be taken when using this product This product is a development supporting unit for use in your progra
12. to operate the PROM programmer refer to the user s manual of the PROM programmer 4 1 Programming Procedures Follow procedures 1 to 8 to write programs into the MCU 1 Read the program into the PROM programmer 8000016 offset required gt 2 Attach the adapter to the PROM programmer see Section 4 2 v 3 Set the jumper switch SW1 see Section 4 3 Dd 4 Insert the MCU into the adapter see Section 4 4 Y 5 Specify the programming area of the MCU using the PROM programmer see Section 4 6 v 6 Using the PROM programmer s erase check function check whether data can be written into the programming area of the MCU v 7 Write the program into the programming area of the MCU using the PROM programmer y v 8 Verify the programming area of the MCU using the PROM programmer to check whether the program is written into the MCU correctly Notes Be sure to set the programming area Otherwise the mode s shift to the programming mode may not be performed successfully The erase check function etc may not also be performed completely 2 Some PROM programmers perform the steps 6 through 8 automatically 8 16 4 2 Attaching the Adapter to a PROM Programmer As shown in Figure 4 1 attach the No 1 pin of the PCA7402E connector standard pitch 32 pin pin header mounted to the No 1 pin of the IC
13. y occurring by using any other PROM programmers can not be supported For the latest type of PROM programmers contact the manufacturer to confirm whether it can be used for your product Table 5 1 Recommended PROM programmers R4945 Advantest M5M27C401 mode R4945A FANS Uh ue x Cautions for Recommended PROM Programmers 1 Choose the programming mode properly Incorrect setting may destroy the MCU 2 The programming method in M5M27C401 mode is the byte programming method 12 16 6 Memory Map Figure 6 1 shows memory maps of the MCU and the PROM programmer Offset 8000016 0000016 0000016 Unused area OFFFFie 1000016 OSDROM area 2FFFF 6 Internal reserved area 3000016 Unused area 4EFFFie 5000016 o Programming area OSDROM area AEFFF is 128K bytes B000016 ZFFFFie Internal reserved area PROM programmer CFFFFie M5M27C401 mode D000016 Internal ROM area 192K bytes FFFFF 6 MCU Figure 6 1 Memory map 13 16 7 How to Request for Support After checking this manual fill in the following information and email to your local distributor For prompt response please specify the following information 1 Contact address e Company name e Department e Responsible person e Phone number e Fax number e E mail address 2 Product information e Name of the programming adapter e Serial number e Date of purchase e Target MCU e Sympt
Download Pdf Manuals
Related Search